| Age | Commit message (Collapse) | Author |
|---|
|
Due to layout restrictions on mc_ehl2, the SD-card interface is limited
to operate in DDR50 mode. The alternative modes SDR104 and SDR50 are not
supported. Limit the capabilities in the SD card controller to DDR50
mode only so that the SD card driver in OS will choose the right mode
for operation even if the attached SD card supports higher modes.
Change-Id: Idc7f1466ec71f4218f6b957cadeeffadd069eb2d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Since the new RTC is located in I2C bus 1 now, set the bus speed to
100 kHz as well.
Change-Id: Ica9468e559bc654545592a9b4d23f3164eafca8a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67102
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the latest redesign a new RTC was introduced on mc_ehl2. Instead
of the old RX6110SA the new Micro Crystal RTC RV3028 is used now. Since
the address of this new RTC conflicts with an EEPROM on I2C bus 2, the
new RTC was moved to I2C bus 1.
As the mainboard is not finished yet, there are no incompatibility
issues with this change. Every new mainboard will have the new RTC and
the older mainboards are not delivered yet.
Change-Id: I3dd00855b8c9b22bdea21d3c8563cdb392868751
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With a redesign of mc_ehl2 the used RTC was changed. In order to be able
to select a different RTC type for every variant move the RTC Kconfig
switch into the variant's Kconfig file.
Change-Id: Ia24703ede6a935e3b9886df87237857baec7d6a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67100
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
mc_apl7 does not use security features like VBOOT and TPM.
Test: flash mc_apl4 mainboard and ensure the disabled features via log.
Change-Id: I16683b92deb047208848b69c5aa79dc4212ce930
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65284
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch adds a new mainboard variant called mc_apl7 which is based
on mc_apl4. So far only the names have been adjusted with no further
changes. Following commits will introduce the needed changes for this
mainboard variant.
Test: build mc_apl7, flash to mc_apl4 and compare log level 8 output
Change-Id: Ie9f2f5c29d071de442f8f3e3eaf4b3c2a6b8920f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65283
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook Up SataPortsEnable to the devicetree. As the default value is 0,
set both [0] and [1] in all mainboards so they aren't affected.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ica8cf9484a6e6fe4362eabb8a9a59fcaf97c1bd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64524
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the following mainboards, since it is
obsolete now.
* siemens/chili
* starlabs/laptop/cml
Change-Id: I173b87da5ce76549672c50ba30204cd77be8b82f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Disable RAPL for all mainboards based on mc_ehl for stable real time
mode of CPUs.
Test: Boot mc_ehl1 with this patch and ensure the bits in the MCBAR
register are cleared.
Change-Id: Ie58a4b6444d5be088ac2b25ff0a2f5cd33120ace
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are three external Marvell PHY 88E1512 on this mainboard. The PHY
IRQ comes with a falling edge but the EHL MAC side needs a rising edge
signal. For that reason, we need an inversion of the IRQ polarity.
Change-Id: Id3caf582b4434b046779f5733e6ad9b57528ce35
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on quick fix on this commit 7b0fe59be (soc/intel/ehl: Fix
logical bug for PseTsnGbePhyInterfaceType), disable PSE TSN
SGMII as the original intention is to set the PSE TSN phy
interface as RGMII.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Id2e05b19f156621a945110791038bc0d19a0aad0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are two APL specific config switches for RAPL and min. cpu clock
(APL_SKIP_SET_POWER_LIMITS, APL_SET_MIN_CLOCK_RATIO). These switches
could be used in future in other CPU platforms. Move them to common code
instead of having them just for one SOC.
Test: Make sure that the clock ratio (MSR 0x198) and the RAPL settings
(MSR0x610) do not change with this patch applied on mc_apl{1,4,5}
mainboard.
Change-Id: I3d63d1b9b6c96586a3c20bf8c1d8001b1d7c4bed
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
repalcement ---> replacement
Change-Id: I486170e89f75fa7c01c7322bb8db783fd4f61931
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64404
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Program the `SmbusEnable` FSP UPD according to the SMBus PCI device's
state in the devicetree. This avoids having to manually make sure the
SMBus PCI device and the `SmbusEnable` setting are in sync.
Change-Id: I275a981f914a55dc57a75e7d436912ff0255a293
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64402
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard there are legacy PCI devices connected behind a
PCIe-2-PCI bridge. Not all clock outputs of this bridge are used. This
patch disables the unused PCI clock outputs on the XIO2001 bridge.
Change-Id: Iedbf0abfa554e0a6ad5b1d1741f4e9934103d171
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63931
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This variant uses all three EHL Ethernet GbE-TSN Controller so enable
the TSN GbE driver in order to set the needed MAC addresses. The
required function to retrieve a valid MAC address was already implement
in the common mainboard.c for mc_ehl.
TEST:
- Boot mc_ehl2 into Linux and check MAC addr via 'ip a'
Change-Id: Ia052c44feb606f9e1d31d047f2acc67e3226a895
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
TSN runs in SGMII mode on this mainboard. This requires setting the link
speed to 1 Gbps.
Change-Id: I9f1da971b4de5671d6d38be6dbc50edbbe20d157
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard uses all three internal Ethernet GbE-TSN controllers. Two
of them are initialized by the Programmable Services Engine (PSE).
This patch enables the Serial Gigabit Media Independent Interface
(SGMII) mode for GbE PSE0 and GbE PSE1. By setting PCH PSE DMA pins to
host owned, the IO is under control of the IA processor cores through
system software.
TEST:
- Boot mc_ehl2 into Linux and check inet addr via 'ip a'
Change-Id: I74e660548b2c44d5dbdb6023d5a36cfdd7e96f43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
In order to achieve a stable eMMC interface disable the HS400 capability
of the host controller. This will result in an operating mode of maximum
HS200 (200 MHz single data rate) which leads to a more relaxed timing.
Change-Id: I0e125dd569b00f59ae0fd2f76169c4461291b47a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
On mc_apl2 the external RTC is connected to I2C bus 3. All other I2C bus
devices (16.0, 16.1 and 16.2) have been disabled as they are not used.
While coreboot can handle the case where a PCI device does not have
function 0 enabled but a later one (here function 3), Linux seems to
check for function 0 first and ignores the rest if function 0
is missing. So enable PCI device 16.0 in order to let Linux use 16.3
again.
Test=Boot into Linux and make sure that PCI device 16.0 and 16.3 are
visible and I2C attached RTC works properly.
Change-Id: I55a748b6de8128f4b26b908118feff9f06d3fb7c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The mainboards mc_apl{2,4,5,6} use VBOOT for verification and can be in
a recovery state for different reasons. In this case we still want the
MRC cache to be around to avoid the DRAM retraining on every boot.
This patch enables the Kconfig switch HAS_RECOVERY_MRC_CACHE which makes
the already available MRC recovery region in FMAP useable.
Test=Boot mc_apl2 in recovery mode and make sure the recovery MRC
cache is used.
Change-Id: I2ea4993f05dd87a0e637f55e84b4fc06f5e29ecc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision only PCIe RP2 and RP7 are used on this
mainboard.
Change-Id: I7702c2b9058dde1c819cb1df8a68fd602f5997da
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With latest hardware revision SATA interface is no longer used on this
mainboard. The mainboard is still in development and not yet released
and for this reason there may still be adjustments.
Change-Id: Icbf088ce4c907e207f6f5d11b8bf5556fe2c90d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Aggressive Link Power Management are no longer supported on these
mainboards and must therefore be disabled. This feature can have a
negative impact on the real-time behavior of the systems.
TEST:
- Boot into system software on mc_apl1
Change-Id: I8b08381743018790a20273ea1f61e5b0a56e6015
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In order to guarantee data integrity an expired TCO must not hard reset
the board. Select the Kconfig switch to prevent this reset.
Change-Id: I04080c6bcd486e3a406438cc7a703165bb6945a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The only option to make HECI1 function disable on Elkhart Lake SoC
platform is using SBI under SMM mode.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76c625e6221fdef1343599e7dbc7739caa91bf98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng Lean Tan <sheng.tan@9elements.com>
|
|
Found using:
diff <(git grep -l '#include <console/console.h>' -- src/) <(git grep -l 'console_time_report\|console_time_get_and_reset\|do_putchar\|vprintk\|printk\|console_log_level\|console_init\|get_log_level\|CONSOLE_ENABLE\|get_console_loglevel\|die_notify\|die_with_post_code\|die\|arch_post_code\|mainboard_post\|post_code\|RAM_SPEW\|RAM_DEBUG\|BIOS_EMERG\|BIOS_ALERT\|BIOS_CRIT\|BIOS_ERR\|BIOS_WARNING\|BIOS_NOTICE\|BIOS_INFO\|BIOS_DEBUG\|BIOS_SPEW\|BIOS_NEVER' -- src/) |grep "<"
Change-Id: I9116965512a5b3241fd7e28537d96637008b31e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Run the command below to fix all occurrences.
$ git grep -l 'ramstage\*/' | xargs sed -i 's,ramstage\*/,ramstage */,'
Change-Id: Ied155d325846fc0ef3e823e5708c6f74e3d7998f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Reuse the options from Kconfig.name for variant-specific selects.
Change-Id: I35f51756180882d019a3ea8c555ccd18cd588f44
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable TPM init in bootblock so that all further stages and other CBFS
files are directly measured into PCRs immediately instead of being
logged into a buffer and replayed to the TPM in ramstage.
Change-Id: Ib3ac29aa72abe8e967660ae7e8416aeb8812de26
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This board does not have a LPC or eSPI connection to the NC FPGA anymore
and therefore IO port 0x80 is not useable for POST codes anymore. Enable
the feature of sending the POST codes to the NC FPGA via PCI so that the
POST codes are visbile again in coreboot.
Change-Id: I9043e4ec9a2ad6b946e373bb3dce9da3d42d00d1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision all clock outputs will be used on this
mainboard. For this reason set all clock source mappings to
'PCIE_CLK_FREE' to have a free running clock.
Change-Id: Ic3f6fb4e24128742ed72dade7a4555c39fb722ae
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
HECI #2 is not used for CSE communication. Therefore, it is not
necessary to set the parameter 'Heci2Enable' in devicetree.
Change-Id: I7012e4d877a464699727ca775af3f9965e0602e9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I329efcb42a444b097794fde4f40acf5ececaea8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
|
|
All the mainboard variants of mc_ehl do not use the external switches
for the bypass rails. Disable the matching UPDs and all the low power
modes of the PMC.
Change-Id: I08f4effe5c4d5845bed01dfe1bd1251c58012b7f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58895
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to get a reliable real-time performance disable all P-States
for all mc_ehl based mainboard.
Change-Id: I22857cc0f1476483ca82c1c872e4519e4b350ea9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Disable all C-states other than C0/C1 for CPU and package.
Change-Id: I2c163f859dab4b0dc02896c70122e993cdd3db72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: I7486f9ba362c80b43b6c888a3b40a4c947218299
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58887
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a prevention of Row-Hammer attacks enable the FSP-M parameter
'RhPrevention'.
Change-Id: I52f68525e882aee26822d9b3c488639c00f27d17
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This configures GPIO GPP_G5 as an input pin for SD card detect.
Change-Id: I708eb112fa054f2f88857001c409fb62493b6206
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
PCIe root ports #4 (00:1c.3) and #6 (00:1c.5) are currently not used on
this mainboard and are not routed either, so remove them from the
devicetree completely. PCIe root port #7 (00:1c.6) is connected and
used. Add the missing settings for L1 substates and latency reporting to
disable these features for this port as well.
Change-Id: I47e8528bea993ed527a0aecdbc93b94bbd9a7a49
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On mc_ehl2 there are currently four of the six PCIe clocks used to drive
PCIe devices. None of the used clock output is dedicated to a special
device. Therefore do not use a port mapping of the clocks to avoid a
stopping clock once a device is missing and the matching root port is
disabled. Instead set the mapping to 'PCIE_CLK_FREE' to have a free
running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I81419887b7f463a937917b971465245c1cb46b94
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
|
|
On mc_ehl1 there are three of the 6 PCIe clocks used to drive PCIe
devices. None of the used clock output is dedicated to a special device
(CLK0 drives several devices on the mainboard, CLK1 and CLK2 are
connected to a PCIe switch). Therefore do not use a port mapping of the
clocks to avoid a stopping clock once a device is missing and the
matching root port is disabled. Instead set the mapping to
'PCIE_CLK_FREE' to have a free running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I2beea76ff8fefd79f476bef343d13495b45cdfcf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58740
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIe root ports #5 (00:1c.4) and #6 (00:1c.5) are not used on this
mainboard and are not routed either, so remove them from the devicetree
completely. PCIe root port #7 (00:1c.6) is connected and used. Add the
missing settings for L1 substates and latency reporting to disable these
features for this port as well.
Change-Id: I06f59f0369ffcd958b5fe12bb3c646d37103811f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58568
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: Ia5ffb382e3524e61b8583aca801063942fe2f247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The `SMBIOS_PROVIDED_BY_MOBO` Kconfig option is already selected through
the `SECUNET_DMI` option. So, there's no need to select both of them.
Change-Id: I784df87893043a011906af8808aff27d636c7626
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58625
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the PCH serial IO settings, suitable for this mainboard.
Change-Id: I3c9915b2d52fbc6a15ac1e68c77bfb3983f7b1cd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I691d91d2a76e27b8efdc18eeae737a78e9ae38fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: I8112fa5ea86e879741061798530150701b759156
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has its own coreboot ready LED. The LED is switched
on via GPIO GPP_F20.
Change-Id: I3570d691e90d2cb6e11b856b876f0327da118522
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In upcoming patches, we need mainboard specific adjustments.
Change-Id: Icf9d829b19b2d26a39ad34be4658064083e9da6d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Enable LPC ComB on this mainboard.
TEST:
- Boot Linux and check with 'dmesg | grep tty'
Change-Id: I7ec58685a723c177df18144011934b206e6425d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses an eSPI-to-LPC bridge for console output. For this
reason, the internal LPSS UART must be disabled.
Change-Id: I86777cf719def331f4d257ddd94e9a87125ebce8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the GPIOs according to the circuit diagram for this mainboard.
Change-Id: I19dc24a16ee9f533b45879bf60fb441e24018cc8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has only SATA Port 1 available with no device sleep
feature.
Change-Id: I338833f2f9bcb407599cfc676ead0b8a9d7379bd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Change-Id: I0c97e2dc589bf6b89713a473925e42a20278f457
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are currently two variants for mc_ehl where different UARTs are
used for the console. Move the Kconfig switch UART_FOR_CONSOLE to the
Kconfig of the variant and select the matching value there.
Change-Id: I7152013a0e32ff151b92932a47953705e591dc0d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58052
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new variant of the mc_ehl board called mc_ehl2. This patch just
copies the files and renames things where needed.
Following patches will adapt the needed features for this new variant.
Change-Id: I3ec3c091017fd66fe6a09216203cdc7c9e833846
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Enable LPSS UART for coreboot console on mc_ehl1.
Change-Id: Id995953741d48fbbe2482ff7c0ef81cac5a31207
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I8c5d6686bf7c694f9d594e3801c79cfd7fb3da80
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56342
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some legacy devices need to have the master bit set in the PCI config
due to old drivers not setting it correctly. Set the master bit if the
feature is enabled via Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
For now, the PCI devices with the ID 110a:403e and 110a:403f needs this
master bit to be set.
Change-Id: Id3f6bda97e5f47d0613a1db8f8adac0b158ab8b1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56632
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Boards based on mc_ehl have, just like some mc_apl variants, legacy
devices on the PCI bus which take longer to boot. In order to ensure
that they will be enumerated correctly wait for them to come up before
PCI scan starts.
TEST=Checked that the new message is visible in the log.
Change-Id: If2f935b69ddaa9364566deacfada5e7d41fcdabd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56631
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Latency Tolerance Reporting is yet another PCIe power management feature
which can have a bad influence on realtime performance. Disable this
feature for all PCIe root ports.
Change-Id: I38023e095ca55efd2178ad944f651fee1f1c34cd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
L1 substates of a PCIe link are meant to save some power when the link
is not active but have the drawback that the PCIe latency is increased
as PLLs are switched on and off as needed.
In order to get a better realtime performance, disable all substates for
every PCIe root port.
Change-Id: Ic5bc8410709d0f0094810bc11a7723e88c30e397
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This variant uses I210 MACPHYs so enable the I210 driver in order to set
the needed MAC addresses. In addition add the function to retrieve a
valid MAC address for the given MACPHY.
Change-Id: Id1d59349db1b86cfdd71bbe27577c0530e8f0b51
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56567
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All the boards based on the mc_ehl baseboard have the NC-FPGA available.
Enable the appropriate driver on baseboard level.
Change-Id: I40b76a837b7ddb70ceba3135996b1c1080170c4d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56566
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All variants based on mc_ehl will use the Siemens HWILIB. Select the
Kconfig switch on baseboard level.
Change-Id: I940f84a4a7449487fe78c793f8dbb1c1b49fa54b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56565
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable IBECC for mc_ehl1 to provide a memory failure protection.
Change-Id: If8f81d6bacb77dc38e231c1cedf22831de8a38a9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56564
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In favor of better realtime performance disable dynamic frequency
support in the System Agent for mc_ehl1.
Change-Id: I0e62bcf2e5efa97d89bf7192f1536747a02ad992
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56563
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable measured boot for all boards based on mc_ehl baseboard.
Change-Id: I3aff943305c024d1f25d2127e6f60495828da3eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
All the boards based on the mc_ehl baseboard have a TPM which is
connected to SPI but mapped into the address space of the x86 so that
it acts like a LPC attached TPM. Enable the TPM driver so that it will
be used. In addition add the needed entry in devicetree.
Change-Id: I301d0ed4a108bac45d95eced120e7ba280945d9c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
All the mainboards based on mc_ehl use the external RTC RX6110SA.
Enable the driver in Kconfig for all boards based on mc_ehl. In
addition, as mc_ehl1 has the RTC attached to the SMBus, add the
devicetree entry on behalf of the SMBus device 00:1f.4 for this variant.
Change-Id: Ie1f45d0e6f9063c00253fe58a6268d40de91cf63
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56523
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `FMDFILE` Kconfig symbol once instead of doing
so on each and every mainboard.
Change-Id: I810bd3fe8d42102586db6c2c58b7037a60189257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56557
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `DEVICETREE` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If68f11a5ceaa67a3e8218f89e1138c247ebb9a25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56555
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to specify the type of the `CBFS_SIZE` Kconfig symbol
more than once. This is done in `src/Kconfig`, along with its prompt.
Change-Id: I9e08e23e24e372e60c32ae8cd7387ddd4b618ddc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide a valid GPIO configuration based on the mainboard wiring.
Change-Id: I36f0e8292a405b4bac74fbc5fde62e5e414387e7
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56519
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there is no SD card interface on this mainboard do not set the
card detect GPIO.
Change-Id: Ibe6799c5c540538f97d1726ec16e79f3edbb16fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56489
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE instead of
PCI_ALLOW_BUS_MASTER to enable PCIe bus master bit as requested in
CB:56441 during review.
Change-Id: I433dbae0d9b15e41d1d0750298868341ce3d6b46
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Since this mainboard does not use GSPI at all, disable all GSPI ports.
Change-Id: I60254e9f4047537d86c972151ec9e33552332959
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses I2C1 and I2C4 buses only. Disable all the others as
they are not connected at all.
Change-Id: I4743f6ea6b9a9987ad63b60f56ee9a597a08284b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Features like DevSLP and Aggressive Link Power Management are not
supported on this mainboard and are therefore disabled.
Change-Id: I3bc650ea78be8587889fb7abfe7075cd9a122198
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board does not use CLKREQ-signaling for PCIe, so disable the pin
assignments. In addition only three clock outputs are used for PCIe,
therefore disable all others to improve EMI.
Change-Id: I545f890fa55a109df7f44d2c82170874fb769009
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56455
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are in total three USB ports that are used on mc_ehl1:
- Port 1: Type A connector connected to USB2/USB3 port 0
- Port 2: Type A connector connected to USB2/USB3 port 1
- Onboard: connected to USB2 port 2
None of the ports supports overcurrent reporting.
Adjust the appropriate UPDs in devicetree to match the hardware
configuration.
Change-Id: I220637b8e9f03efccacd0955e82cfc0c7a6f53ee
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56454
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mc_ehl1 does not have a display attached nor have a display
connector available (pure headless design), remove display related
settings from the devicetree.
Change-Id: Id31c09fcfba15f55eed19134bd0c2fb887bd2478
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56453
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Take Kconfig switch PCI_ALLOW_BUS_MASTER into account and set the PCI
bus master bit for legacy devices only if it is allowed.
Change-Id: I7798a767d528419bb093f301140ab68cc8b9c5ae
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
