summaryrefslogtreecommitdiff
path: root/src/mainboard/siemens/mc_bdx1
AgeCommit message (Collapse)Author
2018-01-26mb/*/*/cmos.layout: Fix the values for the console levelArthur Heymans
Fix the values that were off by one. This was discovered when using postcar stage that prints with debuglevel BIOS_NEVER. Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/23186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-10-19siemens/mc_bdx1: Initialize GPIOsWerner Zeh
Add GPIO initialization for mc_bdx1 mainboard. Call init_gpios() as early as possible as FSP will set up things (like hiding PCI devices) rather early. If connections on the mainboard are dependent on GPIO settings then FSP can screw things up (e.g. disabling not yet connected PCI root ports). Change-Id: I003277cfb871f861900b7fcdc5ec851d4c1c1e6a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/22035 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-10-12siemens/mc_bdx1: Add delay to wait for legacy devicesWerner Zeh
Like happend in commit efd0eb35af5e5620331d885d3140c734a6fc9098 (siemens/mc_apl1: Add delay to wait for legacy devices) add the feature to mc_bdx1 as it uses the same legacy devices. Change-Id: I355a53ce7aea70098d7bc08f24dc6a4e43d1d618 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/21933 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-09-23mb/*/*: Remove rtc nvram configurable baud rateArthur Heymans
There have been discussions about removing this since it does not seem to be used much and only creates troubles for boards without defaults, not to mention that it was configurable on many boards that do not even feature uart. It is still possible to configure the baudrate through the Kconfig option. Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/19682 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-08-18drivers/i2c/rx6110sa: Drop I2C interface arbitrationNico Huber
Change-Id: Ib31e77eec639c231520198c0b978d6c3c1eadaed Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20454 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-06mainboard/[m-w]: add IS_ENABLED() around Kconfig symbol referencesMartin Roth
Change-Id: Ifba3257b0328d0b6ad1bee9bf885683998df5851 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/20344 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-06-30mb/siemens/mc_bdx1: Set up RTC backup mode to primary cellWerner Zeh
The used RTC6110SA has issues to enter backup mode when the power supply decreases too slow when the mainboard is turned off. Switch to backup mode "primary cell" to make sure backup mode will be entered correctly on power-off. In addition set IOCUTEN to minimize the backup current consumption of the RTC. Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20413 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-06-29mb/siemens/mc_bdx1: Set bus master bit for on-board PCI devicesWerner Zeh
There are up to two on-board PCI devices where bus master has to be enabled in PCI config space. As there is no need for a complete PCI driver for these devices just set the bus master bit in mainboard_final(). In a perfect world that would be the task of the runtime driver which unfortunately don't do that. Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-05-31mc_bdx1: Switch to RTC RX6110SAWerner Zeh
The prior used RTC PCF8523 is replaced with RX6110SA on this mainboard. Switch to the new RTC in Kconfig and adapt devicetree to the new chip. Change-Id: I7c4911191cae254900f9a958da42ecd18497484c Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/19979 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-03-21mainboards: Don’t select `CONSOLE_POST`Paul Menzel
Currently, it’s impossible for the user to select `NO_POST`, for boards selecting `CONSOLE_POST` in their config. ``` warning: (BOARD_SPECIFIC_OPTIONS) selects CONSOLE_POST which has unmet direct dependencies (VENDOR_SIEMENS && BOARD_SIEMENS_MC_BDX1 || !NO_POST) ``` This is currently done for Intel Camelback Mountain and Siemens MC-BDX1. Selecting the option `CONSOLE_POST` in board specific configuration is not a good idea, as this should be user configurable over Kconfig, and also the tree-wide defaults should be the same for these options. Kconfig is different, as commit 97535558f1 (mainboard/{google,intel}: Change config option selection) only touch the Intel board. Change-Id: I91c1e0cb92ed218b6bbc7c33759b91f748cf6f51 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/18878 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2016-09-12siemens/mc_bdx1: Enable decoding for COM 3 & COM 4 on LPCWerner Zeh
Since this mainboard provides 4 COM ports on LPC, enable decoding of the corresponding addresses using the generic LPC decode registers. Change-Id: I0e93d40dca01d55f3567a18c7ec02269e3bec466 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/16535 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-08-17mainboard: Clean up boot_option/reboot_bits in cmos.layoutNico Huber
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector code) the reboot counter stored in `reboot_bits` isn't reset on a reboot with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR enabled, later stages (e.g. payload, OS) have to clear the counter too, when they want to switch to normal boot. So change the bits to (h)ex instead of (r)eserved. To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also remove all occurences of the obsolete `last_boot` bit that have sneaked in again since 24391321 (mainboard: Remove last_boot NVRAM option). Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/16157 Tested-by: build bot (Jenkins) Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com> Reviewed-by: York Yang <york.yang@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-08-01Add newlines at the end of all coreboot filesMartin Roth
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/15974 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-14siemens/mc_bdx1: Add usage of external RTC PCF8523Werner Zeh
This mainboard contains an external RTC chip PCF8523. Enable usage of this chip and add some initialization values to device tree. Change-Id: I25c0a017899ee904f3aa02bdc7dcaf61dee67e3a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15642 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-08siemens/mc_bdx1: Move SCI to IRQ 10Werner Zeh
IRQ 9 is used for different purpose on this board so move SCI away to IRQ10. Change-Id: I107bfb5ec8cd05f844ee75550779be7746e77a88 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15563 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-07-07siemens/mc_bdx1: Set up opcode menu for SPI controllerWerner Zeh
Since SPI controller opcode registers are locked by FSP, they need to be initialized to a known good state before ReadyToBoot event and after every SPI flash access (e.g. for MRC cache) has been finished in order to enable the OS to use SPI controller without constraints. Change-Id: I0a66344cd44e036c3999ae98d539072299cf5112 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15547 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2016-07-06siemens/mc_bdx1: Add usage of Siemens NC FPGA driverWerner Zeh
Enable NC FPGA driver for this mainboard. Change-Id: I87b6b10038f3d161a25b2008b7ea44b5627cca43 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15545 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-07-05siemens/mc_bdx1: Set up MAC address for available i210 MACsWerner Zeh
Enable the usage of DRIVER_INTEL_I210 and provide a function to search for a valid MAC address for all i210 devices using hwilib. Change-Id: Ic0f4f1579364cf5b0111334a05a8a0926785318b Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/15517 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2016-04-29siemens/mc_bdx1: Add new mainboard.Werner Zeh
Add new mainboard for MC BDX1 board which is based on Intel Camelback Mountain. This mainboard is an industry type board and has several Ethernet interfaces among with two USB3.0 connectors. It uses 24V DC power supply and has its own form factor which does not match any standard. This commit adds the new mainboard and prepares the Kconfig environment so that this board can be selected and generated. Although the generated image can boot into Linux and DOS, not all functions are implemented yet. Forthcoming commits will add more functionality. Change-Id: I29011cfd3b0d13bcf163223f657e02f69978e39a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/14516 Tested-by: build bot (Jenkins) Reviewed-by: York Yang <york.yang@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 12:00:02 +0000