summaryrefslogtreecommitdiff
path: root/src/mainboard/siemens/mc_apl1
AgeCommit message (Collapse)Author
2017-11-07siemens/mc_apl1: Select CONFIG_NC_FPGA_NOTIFY_CB_READYMario Scheithauer
For internal measurements this mainboard needs a marking inside the NC FPGA when coreboot is ready and payload has been loaded. Change-Id: I37908b21e2a077dec7fa99b0db6d1fd9b6878341 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/22356 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-11-03siemens/mc_apl1: Enable I2C0 with 100kHzMario Scheithauer
The default setting for I2Cx is 400kHz. On this mainboard there is a device on I2C0 which requires a lower clock rate to work correctly. For this reason we set the frequency to 100kHz. Change-Id: I637a58a0c89ead55ca1176d6aecdfaba5897d64f Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/22140 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-11-03siemens/mc_apl1: Set coreboot ready LEDMario Scheithauer
This mainboard has its own coreboot ready LED. The LED is switched on via GPIO CNV_RGI_DT. Change-Id: I179d013746c1334337dc9e6b7f09ac54eff0cd77 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/22136 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-11-03siemens/mc_apl1: Add legacy IRQ routing for PCI devicesMario Scheithauer
On this mainboard there are PCI devices, which are connected to the PCIe root port via a PCIe-2-PCI bridge. One of the devices only supports legacy interrupt routing. For this reason we have to adjust the PIR6 register (0x314c) which is responsible for PCIe device 13h and 14h. This means that the interrupt routing will also be the same for both PCIe devices. The bridge is connected to PCIe root port 4 (Device 14.0). The following routing is required: INTA#->PIRQB#, INTB#->PIRQC#, INTC#->PIRQD#, INTD#->PIRQA# Change-Id: I5464c9a2669773bc1e6cd4b4d29d1be838dbfa27 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/22139 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-09-26Use stopwatch_wait_until_expired where applicableJonathan Neuschäfer
Change-Id: I4d6c6810b91294a7e401a4a1a446218c04c98e55 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/21590 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-09-21siemens/mc_apl1: Move SCI to IRQ 10Mario Scheithauer
IRQ 9 is used for different purpose on this mainboard so move SCI away to IRQ 10. Change-Id: I7f055447f5d92bc4696b38e8103a7aebde95d9d3 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/21586 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-09-14siemens/mc_apl1: Add delay to wait for legacy devicesWerner Zeh
There are old legacy onboard devices which are too slow for a coreboot boot with log level BIOS_ERR. In this case coreboot is so fast that these devices do not have enough time to become visible on the PCI bus and this in turn leads to missing resource allocation for this devices. The most generic way to work around this problem on existing hardware is to introduce a delay right before the PCI enumeration starts. The needed delay time depends on the hardware and will therefore be get from hwinfo. Change-Id: Ia91babc81e3a347bbc498c3def97b2ea70e10922 Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/21518 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
2017-09-08siemens/mc_apl1: Disable internal UARTsMario Scheithauer
APL internal UARTs are not used on this mainboard. Change-Id: I39118262fc6f37b45785538a3f2d1d31d42cbe86 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/21406 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-09-08siemens/mc_apl1: Set bus master bit for on-board PCI deviceMario Scheithauer
There is one on-board PCI device where bus master has to be enabled in PCI configuration space. As there is no need for a complete PCI driver for this device just set the bus master bit in mainboard_final(). Change-Id: I45202937eba11da3bea14fef6ebed70599804335 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/21405 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-08-18include/device: Split i2c.h into threeNico Huber
Split `i2c.h` into three pieces to ease reuse of the generic defi- nitions. No code is changed. * `i2c.h` - keeps the generic definitions * `i2c_simple.h` - holds the current, limited to one controller driver per board, devicetree independent I2C interface * `i2c_bus.h` - will become the devicetree compatible interface for native I2C (e.g. non-SMBus) controllers Change-Id: I382d45c70f9314588663e1284f264f877469c74d Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/20845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-08-15soc/intel/common/block: Add LPC Common code and use it for APLRavi Sarawadi
Add LPC common code to be shared across Intel platforms. Also add LPC library functions to be shared across platforms. Use common LPC code for Apollo Lake soc. Update existing Apollolake mainboard variants {google,intel,siemens} to use new common LPC header file. Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/20659 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-27siemens/mc_apl1: Select skip RAPL configurationMario Scheithauer
The mc_apl1 mainboard needs to disable the RAPL algorithm for a constant power management of the processor package. An active RAPL algorithm leads to negative effects with our real time software. Change-Id: I09ca56a034fd3896a000e64cac35f12fb507a682 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20760 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-07-20siemens/mc_apl1: Activate ECC for DRAMMario Scheithauer
This mainboard is equipped with DDR3L modules which support ECC. The BWG says that for activating ECC the FSP-M parameter MemoryDown must be set to 5. Change-Id: Idc68df1e2bae2396c9b9788d4a026a75b7d9119b Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20634 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-07-20siemens/mc_apl1: Include platform.aslMario Scheithauer
The OS of this mainboard needs the _PIC method for the selection of the type of interrupt routing. Change-Id: Ic82ba1b368aff0030422d9602ebc882247a2191b Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20618 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-07-18siemens/mc_apl1: Disable SDCARDMario Scheithauer
SDCARD is not used on this mainboard. Change-Id: I28d23cdb3652bf736b19daf67c7057c396230e24 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20611 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-07-13Rename __attribute__((packed)) --> __packedStefan Reinauer
Also unify __attribute__ ((..)) to __attribute__((..)) and handle ((__packed__)) like ((packed)) Change-Id: Ie60a51c3fa92b5009724a5b7c2932e361bf3490c Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-on: https://review.coreboot.org/15921 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-06-30mb/siemens/mc_apl1: Set up RTC backup mode to primary cellWerner Zeh
Set RX6110SA RTC backup mode to primary cell. This mode reduces the backup current consumption of the RTC. Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/20414 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2017-06-23siemens/mc_apl1: Enable decoding for COM 3 on LPCMario Scheithauer
It does not work to enable the LPC range in the function mainboard_init() because the LPC bus driver closes the range during PCI enumeration again. For this reason, enabling decoding of the address range for COM 3 will be done at a later point in time - mainboard_final(). Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20295 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-23siemens/mc_apl1: Disable XDCIMario Scheithauer
With enabled XDCI support we are not able to use USB port 0 over XHCI driver. For this reason, we disable XDCI into devicetree.cb. Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20296 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-13siemens/mc_apl1: Enable decoding for COM 3 on LPCMario Scheithauer
Since this mainboard provides 3 COM ports on LPC, enable decoding of the corresponding address range for COM 3. Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20162 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-06-13siemens/mc_apl1: Use Siemens NC FPGA driverMario Scheithauer
- use Siemens NC FPGA driver for backlight brightness and PWM control - set Dsave time for board reset after falling edge of signal xdsave Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/20161 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-05-17siemens/mc_apl1: Program eMMC DLL settingsMario Scheithauer
Program eMMC DLL settings for mc_apl1 mainboard, after that system can boot up with eMMC successfully. Change-Id: I3d60f66ec5c7e09540ccda59f244aac6f78bf954 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19712 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-17siemens/mc_apl1: Select external 8250 UARTMario Scheithauer
The mainboard siemens/mc_apl1 uses an external I/O port for console output. For this reason we need to activate the 8250 LPC UART. Change-Id: Ib5616a116aec6135191bdce95f9f9566ce13d6f1 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19694 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-05-11siemens/mc_apl1: Add usage of external RTC RX6110 SAMario Scheithauer
This mainboard contains an external RTC chip RX6110 SA. Enable usage of this chip and set some initialization values to device tree. Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19647 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-11siemens/mc_apl1: Correct GPIO settingsMario Scheithauer
- set GPIO_183 to high level for enabling the power of SD card - delete all GPIOs for JTAG interface because they lead to problems with Lauterbach debug hardware Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19623 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-05-05mainboard/siemens/mc_apl1: remove unnecessary headerAaron Durbin
soc/i2c.h does not need to be included in this compilation unit. Change-Id: Ife11642d2e69af7235c93fc54bba38853b046169 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19572 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-04-04siemens/mc_apl1: Activate PTN3460 eDP to LVDS bridge ICMario Scheithauer
This mainboard uses a LVDS connection for LCD panels. Apollo Lake SoC provides a display controller with three independent pipes (1x eDP and 2x DP/HDMI). PTN3460 is an embedded DisplayPort to LVDS bridge device that enables connectivity between an eDP source and LVDS display panel (http://www.nxp.com/documents/data_sheet/PTN3460.pdf). The bridge contains an On-chip Extended Display Identification Data (EDIT) emulation for EDIT data structures. This patch sets up PTN3460 to be used with the appropriate LCD panel. Change-Id: Ib8fa79bb608f1842f26c1af3d7bf4bb0513fa94d Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/19043 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-29siemens/mc_apl1: Adjust gpio settingsMario Scheithauer
Adjust gpio settings according to the hardware layout. Change-Id: I2f440e863c2e6f59298c500ac5aefa3b7386bcdf Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18995 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-03-15siemens/mc_apl1: Clean up the codeMario Scheithauer
This patch make some general adaptations in relation to commit 6a489237 (mainboard/intel/leafhill: Clean up). - add necessary defaults to Kconfig - remove irrelevant entries from FMD file - include romstage file for better understanding Change-Id: I190d648a7ffeca11acc6560db85ff03c78e85b21 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18808 Tested-by: build bot (Jenkins) Reviewed-by: Andrey Petrov <andrey.petrov@intel.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20siemens/mc_apl1: Set MAC address for all available i210 MACsMario Scheithauer
This mainboard uses two i210 Ethernet controller. Therfore we enable the usage of the i210 driver and have to provide a function to search for a valid MAC address for all i210 devices by using Siemens hwilib. Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18380 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-15siemens/mc_apl1: Make basic settings for booting the mainboardMario Scheithauer
This commit makes a basic adjustment for GPIOs, device tree, flash map and MRC settings. With these basic settings the mainboard boots into Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow. Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18292 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-02siemens/mc_apl1: Add new mainboardMario Scheithauer
This mainboard is based on Intel's Leafhill CRB with Apollo Lake silicon. In a first step, it concerns only a copy of intel/leafhill directory with minimum changes. Special adaptations for MC APL1 mainboard will follow in separate commits. Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18272 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 20:55:29 +0000