| Age | Commit message (Collapse) | Author |
|---|
|
It does not work to enable the LPC range in the function
mainboard_init() because the LPC bus driver closes the range during PCI
enumeration again. For this reason, enabling decoding of the address
range for COM 3 will be done at a later point in time -
mainboard_final().
Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With enabled XDCI support we are not able to use USB port 0 over XHCI
driver. For this reason, we disable XDCI into devicetree.cb.
Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Program eMMC DLL settings for mc_apl1 mainboard, after that system can
boot up with eMMC successfully.
Change-Id: I3d60f66ec5c7e09540ccda59f244aac6f78bf954
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The mainboard siemens/mc_apl1 uses an external I/O port for console
output. For this reason we need to activate the 8250 LPC UART.
Change-Id: Ib5616a116aec6135191bdce95f9f9566ce13d6f1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This mainboard contains an external RTC chip RX6110 SA. Enable usage of
this chip and set some initialization values to device tree.
Change-Id: I5aceb4401f0bb059ef893dfe7d157716c82e4a76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
- set GPIO_183 to high level for enabling the power of SD card
- delete all GPIOs for JTAG interface because they lead to problems with
Lauterbach debug hardware
Change-Id: I24bfff479601933c43e3dcbfa3baa49510831703
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
soc/i2c.h does not need to be included in this compilation unit.
Change-Id: Ife11642d2e69af7235c93fc54bba38853b046169
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard uses a LVDS connection for LCD panels. Apollo Lake SoC
provides a display controller with three independent pipes (1x eDP and
2x DP/HDMI). PTN3460 is an embedded DisplayPort to LVDS bridge device
that enables connectivity between an eDP source and LVDS display panel
(http://www.nxp.com/documents/data_sheet/PTN3460.pdf).
The bridge contains an On-chip Extended Display Identification Data
(EDIT) emulation for EDIT data structures.
This patch sets up PTN3460 to be used with the appropriate LCD panel.
Change-Id: Ib8fa79bb608f1842f26c1af3d7bf4bb0513fa94d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/19043
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adjust gpio settings according to the hardware layout.
Change-Id: I2f440e863c2e6f59298c500ac5aefa3b7386bcdf
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18995
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch make some general adaptations in relation to commit 6a489237
(mainboard/intel/leafhill: Clean up).
- add necessary defaults to Kconfig
- remove irrelevant entries from FMD file
- include romstage file for better understanding
Change-Id: I190d648a7ffeca11acc6560db85ff03c78e85b21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18808
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard uses two i210 Ethernet controller. Therfore we enable the
usage of the i210 driver and have to provide a function to search for a
valid MAC address for all i210 devices by using Siemens hwilib.
Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18380
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This commit makes a basic adjustment for GPIOs, device tree, flash map and
MRC settings. With these basic settings the mainboard boots into
Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow.
Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18292
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with minimum changes. Special adaptations for MC APL1
mainboard will follow in separate commits.
Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18272
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
|
