|
Enable change Ic6b8ce4a9db50211a9c26221ca10105c5a0829a0
(sb/intel/common: Automatically generate ACPI PIRQ) for BD82X6X.
This generates the main ACPI _PRT table automatically based on the
chipset registers.
Tested on Intel NUC DCP847SKE with Linux 4.13.14:
$ cat /proc/interrupts
CPU0 CPU1
0: 23 0 IO-APIC 2-edge timer
8: 1 0 IO-APIC 8-edge rtc0
9: 0 0 IO-APIC 9-fasteoi acpi
19: 86 0 IO-APIC 19-fasteoi ehci_hcd:usb1
23: 0 0 IO-APIC 23-fasteoi i801_smbus
[...MSI and other interrupts skipped...]
Log messages:
ACPI_PIRQ_GEN PCI: 00:02.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1b.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1c.0: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1c.1: pin=2 pirq=6
ACPI_PIRQ_GEN PCI: 00:1c.2: pin=3 pirq=4
ACPI_PIRQ_GEN PCI: 00:1d.0: pin=1 pirq=4
ACPI_PIRQ_GEN PCI: 00:1f.2: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1f.3: pin=2 pirq=8
ACPI_PIRQ_GEN PCI: 00:04.0: pin=1 pirq=1
Generated _PRT:
Scope (\_SB.PCI0)
{
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
{
If (PICM)
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
0x00000000,
0x00000015
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
0x00000000,
0x00000017
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
0x00000000,
0x00000010
}
})
}
Else
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKF,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKH,
0x00000000
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
}
})
}
}
}
Change-Id: I832a86925283d61b64b8268246d9e6f11994c120
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
