| Age | Commit message (Collapse) | Author |
|---|
|
The attributes are initialized with 0 and thus setting them to 0 makes
them superfluous. Remove them.
Change-Id: I572a9092633c61907794ecbbbe431066d889c5fb
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The attributes are initialized with 0 and thus setting them to 0 makes
them superfluous. Remove them.
Change-Id: Icdf58a85bbde0dcb4e555df68cd20eade241dde3
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83176
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Evers <marvin.n.evers@gmail.com>
|
|
The attributes are initialized with 0 and thus setting them to 0 makes
them superfluous. Remove them.
Change-Id: Icb41f0a9baded01267410bd4c9458ab4bfb82b70
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83175
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Evers <marvin.n.evers@gmail.com>
|
|
The attributes are initialized with 0 and thus setting them to 0 makes
them superfluous. Remove them.
Change-Id: I1239132d5f25345ebb051d216e9187f3d2250339
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83174
Reviewed-by: Marvin Evers <marvin.n.evers@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The attributes are initialized with 0 and thus setting them to 0 makes
them superfluous. Remove them.
Change-Id: Ic16d568c38d708da27efa7229e23019e71c0019b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marvin Evers <marvin.n.evers@gmail.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I7114612e686a0bf3cfc241f45fa62077fad16f5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Replace `0x411111f0` with `AZALIA_PIN_CFG_NC(0)`, which evaluates to the
same value and conveys additional information to the reader. Done with a
bulk search and replace operation.
Change-Id: Ibd84daec017bc1ab1ee4edd906fda80231c134cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
If the ChromiumOS EC indicates that the device has an assistant key,
we should also add it to the generated linux,keymap binding. This
commit simply does so by examining the keyboard capabilities reported by
the EC.
BUG=b:333088656
TEST=With a device that has an assistant key, flash AP FW and verify
that the key is mapped to `KEY_ASSISTANT` in the Linux kernel using
`evtest`.
Change-Id: I217220e89bce88e3045a4fc3b124954696276442
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81996
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Change-Id: I265e427254ce9f735e65b0631c43f98bc778a34f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81812
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Change-Id: Ib1a8fc50217c84e835080c70269ff50fc001392c
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81811
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2285d1bdaa2734658ca1a0cc58ef2294d90d333e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
It's not needed other than for booting w/SeaBIOS, where it is already
selected by default, and enabling it with edk2 payload prevents Linux/
Windows from fully entering S0ix.
TEST=build/boot purism/librem_cnl (Mini v2), verify Win11/Linux able
to enter and exit S0ix properly.
Change-Id: I974a82bedc4e06f48ce801f2bc0c29afbd80ffcf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80602
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The PcieRpEnable option is redundant to our on/off setting in the
devicetrees. Let's use the common coreboot infrastructure instead.
Thanks to Nicholas for doing all the mainboard legwork!
Change-Id: Iea7f616f6db579c06722369c08de7cf7261dece8
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Nicholas Sudsgaard <devel+coreboot@nsudsgaard.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79919
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the baseboard uses chipset devicetree references, remove
all references whose value is identical to the chipset devicetree
default or the baseboard default, since they are pointless clutter.
TEST=build/boot purism/librem_cnl (Mini v2), verify output of lspci
and lsusb unchanged before and after patch.
Change-Id: I12498e7261dafd7ee59fe79926532399392d1b09
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80600
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the board uses chipset devicetree references, remove all
references whose value is identical to the chipset devicetree default,
since they are pointless clutter.
TEST=build/boot purism/librem_cnl (Mini v2), run lspci and verify output
unchanged before and after patch.
Change-Id: I6c656d227962548cebde61f1d82333837adbbf56
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80599
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib7beed7218f317bc2352b65a6191ef1cdaa0742d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: Ia2100d26027a7f71739d5445f781b52c517ed966
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80594
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
As with other devices with only an external display, the Librem mini/
mini-v2 need a few extra seconds (vs an internal panel) for display init in order for the edk2 boot splash to be visible before the
default boot target is booted.
TEST=build/boot Librem Mini v2 w/edk2 payload, verify splash screen
shown / user has time to enter setup menu.
Change-Id: I9d2d514719a9918ee58cc63969b3adae44ac1632
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4790adb41cb62c8c8dd44261a2926dfb6350955a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80111
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
WLAN has always been pcie_rp5, there is nothing on pcie_rp1. RP5 gets
promoted to function 0 (RP1's function) since no earlier functions are
enabled.
This simplifies later refactoring that will handle the FSP root port
enable flags (which were correctly set already) using the device tree
enables.
Test: Boot librem_13v2 and verify WLAN is enabled.
Change-Id: I7a724a01b5f171a16de83ff6122630e2d66557c1
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Change-Id: I87cec9026bcb621ceb7eae51f65ae35bc31d584a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Change-Id: Id592241a1dc33559115800da10a57a5fc10867f9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
Change-Id: I09dd5871cb366ef95410efc1ca6c4337f23b52fd
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79912
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Change-Id: If4f89fb81664474e03ab0ade76cfbd617127127e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79040
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for the Librem 11 tablet, using the ME 13.50.15.1436
binary from the original BIOS (version 28.D8.E1.021) and FSP binaries
from a Jasper Lake Chromebook.
The following features were tested with PureOS:
* Audio (speakers, microphone, headset jack)
* Cameras
* Display
* Touchscreen and pen
* Keyboard cover, with tablet/laptop mode switch indicated via ACPI
* Power and volume buttons
* USB-C ports (USB 2/3, DP alt mode, PD charging)
* SD card reader
* WLAN
* Bluetooth
* NVMe SSD (socketed)
* Battery state information from EC
* Accelerometer
A UART is accessible with soldering via test points on the mainboard,
documented in the mainboard Kconfig with a toggle to enable it for
coreboot logging.
Change-Id: I545994889ddfb41f56de09b3a42840bccbd7c4aa
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The next board revision of Librem 14 (v1-02) has replaced the ALC256
codec with ALC269. Add verbs for it.
Two GPIOs were changed from SMBus native functions to NC for this
revision. They are not used on either revision, change to NC.
Change-Id: I43b6265d2f502c05d5539ff3abf53ade0da6d706
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78347
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New Librem 14s have a newer CPU stepping, which changes them from CML
v1 to v2. The product is not significantly different and remains v1,
specifically "v1-02".
Select SOC_INTEL_COMETLAKE_1_2 to support all CPU steppings.
Change-Id: Iab37208b81e973714a2c088d2346eda518bf1214
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
This adds support for booting the Librem L1UM v2 mainboard with
coreboot, using binaries from the original BIOS.
The following features have been tested on PureOS:
- USB: front USB3, rear USB3, USB2 header on board
- SATA: 8x SATA ports, one M.2 M-key shared with SATA0
- PCIe: two PEG slots, one PCIe slot from PCH, and one M.2 M-key
- Network: 2x GbE
- Video: BMC VGA and IPMI
- Serial: Physical serial port, provided by BMC SuperIO
- Hardware monitor
- POST code display
- TPM2
These binaries are extracted from the original BIOS:
- Intel Management Engine
- Intel Firmware Descriptor
This was developed and tested on a Librem L1UM v2 using a Core i7-9700
CPU. Native graphics init works for the Aspeed AST2500 BMC.
For development, the serial port console works from bootblock. Early
init waits for the BMC to finish booting since this is required for
serial port output.
Change-Id: I990f6024d65098a9553d7d1fe7f36614cc55ea19
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75090
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable HDMI1 output, which corresponds to the physical DisplayPort
connector, so passive adapters to DVI or HDMI will work with native
graphics init.
Change-Id: I95a147978697f4af092fe61ceacd2e725155d489
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Define a CMOS layout for Librem Mini v1/v2 spanning both banks. The
only setting provided is the automatic power-on setting, which is
implemented by the EC. This can now be configured in a firmware image
by replacing cmos.default in CBFS.
Since cmos.default is applied early in bootblock, the EC BRAM interface
must now be configured in bootblock, including opening the LPC I/O
range.
Change-Id: Ib0a4ea02d71f6f99e344484726a629e0552e4941
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74363
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use verbs enabling jack detect if the EC firmware has been updated
with fixed jack detection.
Test: Build Librem 14 and boot with latest EC, test headset jack
detection.
Change-Id: I57a27b1d51e4f6c7c712bcb2823d21692b9c5ce6
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74364
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name.
Change-Id: I2ae03a3ac548674b8c5e7dfaff47d6c536b452f1
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75013
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Librem Mini v1/v2 has an automatic power-on setting provided by the EC
in BRAM bank 1. Use this bank as the high bank of CMOS memory so that
setting can be described in cmos.layout.
Change-Id: Icb87bc521f71aa4350c8f5a64fc2cbe7a7a8c808
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Configure the SuperIO and logical devices in the device tree. This
overrides the power-on default state.
UART1 was already enabled, and if ENABLE_EC_UART1 was selected in
Kconfig, the LPC UART1 I/O range was also already enabled.
The RTC/BRAM interface was enabled (and the BRAM1 base was 0x360 by
default), but the LPC I/O range was not opened previously. Now it is
open and BRAM bank 1 is accessible.
Mouse/Keyboard are not wired to anything on this board and are now
disabled.
UART2, SMFI, power channel 1, and power channel 2 were enabled
previously, but their LPC I/O ranges were not opened and they were not
accessible to the OS. Fan control is performed by the EC on this board
so there is no change.
SWUC and power channels 3-5 were disabled by default, no change.
Change-Id: I58a5a427737f4a2caa64326c110eb53ec00b347d
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove explicit PNP 6e.1 configuration for UART. This had no effect,
the SuperIO is actually on I/O port 2e. Enabling the 8250IO driver is
sufficient to use the UART, the UART device is enabled by default.
Test: Build Mini v2 with and without CONFIG_ENABLE_EC_UART1, boot and
check output on serial.
Change-Id: Idbb39c81cadd633f4718f0682d231dc578d20325
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74362
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I4f2f02623b060ef0ebefc5aceb713c77a8b1e9a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71523
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Id1078b14a805eea53d2a7c5a8183a5413f26e115
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71521
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes using USB-C devices in either orientation on left-side USB-C
port.
Test: Plug USB-C device in both orientations on left-side USB-C port,
check speed with lsusb -t.
Change-Id: I9fbc53bb51a5225e92b0b6bb9ced87a0ab90c9ce
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69702
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The cpu cluster is always present and it's the proper device to contain
the settings that need to be applied to all cpus. This makes it possible
to remove the fake lapic from devicetrees.
Change-Id: Ic449b2df8036e8c02b5559cca6b2e7479a70a786
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59314
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I77a333827552741453d8b575f2a8009b3e1bf8f1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Librem Mini has a UART (accessible with soldering), which is very
useful for work on coreboot. It can be used for coreboot/SeaBIOS/Linux
boot logs, or as a general purpose UART.
Change-Id: I38ad5f19da6af5ed286ad3583f34b824a3660916
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68551
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9b03ccc1100307e3c24393903600d18f6cc9abdc
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68378
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. As done on Haswell, add the `mb_get_spd_map`
function and the `struct spd_info` type to retrieve SPD information from
mainboard code without having to use `pei_data` in said mainboard code.
Unlike Haswell MRC, Broadwell MRC uses all positions of the `spd_data`
array, not just the first. The placeholder SPD address for memory-down
seems to be different as well. Adapt the existing code to handle these
variations. Once complete, the abstraction layer for both MRC binaries
will have the same API.
Change-Id: I92a05003a319c354675368cae8e34980bd2f9e10
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: I8d3b352333bea7ea6f7b0f96d73e6c2d7d1a2cfb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55809
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Introduce the `SPD_MEMORY_DOWN` macro to indicate that a slot is used
with memory-down. This enables computing the channel disable masks as
the bits for slots where the SPD address is zero. To preserve current
behavior, zero the SPD addresses for memory-down slots afterwards.
Change-Id: I75b7be7c72062d1a26cfc7b09b79de62de0a9cea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55807
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert the librem_14 and librem_mini from using separate devicetrees
to using a baseboard devicetree and overridetrees. This reduces code
duplication, and facilitates adding any new variants with minimal
additional code.
Test: build/boot Librem 14 and Librem Mini v2 boards
Change-Id: Ide65ffc750495c9ba2074757ce467efa2f384c56
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Hide the Linux gpio-led ACPI device from Windows by setting the device
status (_STA) to 0xB (enabled, hidden) so Windows doesn't show an
unknown device/missing drivers in Device Manger. Linux doesn't care
about the _STA value.
Test: build/boot Windows (10/11) and Linux (PureOS 10) on a Librem Mini
v2, verify LED works under Linux, is ignored under Windows
Change-Id: If3ee0db685a2f7dab505602afa98c3c2d5adf5d3
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
The front status LED on the Librem Mini is driven by the SATALED# GPIO
line configured for native function, so only shows disk activity for
SATA drives, but not NVMe. To allow it to show disk activity for NVMe
drives as well, reconfigure the GPIO as GPIO-OUT (rather than native
function), and configure it via ACPI so that the linux gpio-leds
driver will attach and use it accordingly.
This has the added benefit of allowing the user to reconfigure the
LED as they see fit via sysfs.
Test: boot Linux (PureOS) on Librem Mini v2 with NVMe drive, observe status
LED blinks during periods of disk activity (tested via 'stress').
Change-Id: I34c2a5f3fd1038266f4514544abfc1020da6f85b
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As all librem_skl devices ship with the ME disabled via HAP bit and ME
firmware "neutralized" via me_cleaner, the HECI1 PCI device should be
marked off/disabled to ensure that heci_reset() is not called at the end
of heci_init(), as this causes a 15s timeout delay when booting
(introduced in commit cb2fd20 [soc/intel/common: Add HECI Reset flow in
the CSE driver]).
Change-Id: Ib6bfcfd97e32bb9cf5be33535d77eea8227a8f9f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
3. Make dt CSE PCI device `on` by default.
4. Mainboards set DISABLE_HECI1_AT_PRE_BOOT=y to make Heci1
function disable at pre-boot instead of the dt policy that uses
`HeciEnabled = 0`.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5c13fe4a78be44403a81c28b1676aecc26c58607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I587dcd8fc208562ecf0e0ba6ea9f741538511192
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
All Coffee Lake mainboards use the default value for the setting
`SataMode`. Thus, drop it from their devicetree.
Change-Id: Ibb329eb8b752c2220bb25f14fb6ae92dd8a308d6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59889
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All Skylake mainboards use the default value for the setting `SataMode`.
Thus, drop it from their devicetree.
Change-Id: I9be5eca93cac65afc4cc30ceb64d9a5b7e5cd514
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59888
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the `AZALIA_RESET` macro, write hex values in lowercase and remove
redundant comments. Also express verb length in decimal.
Tested with BUILD_TIMELESS=1, Purism Librem 15 v4 remains identical.
Change-Id: Id9f5ff9614a8f8c0b7f3a3c633a1dcdda8c5876c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Rewrite the HDA configuration using macros for clarity.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I987a41329425a5c8c7169a7fa66a34de5742532e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Switch to common GNVS. No additional fields to those being present in
common GNVS are used by any SKL/KBL device. Thus, they're dropped
completely.
Change-Id: I87ab4ab05f6c081697801276a744d49e9e1908e0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
The `IRQ_SLOT_COUNT` value is only meaningful when generating a PIRQ
table. None of these boards do it, so specifying this value achieves
absolutely nothing. Drop it to prevent further useless copy-pasting.
Change-Id: I2d63b850c03fc1471c0eef180e8b621311b2c336
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Test: build/boot Purism Librem 13v1, verify brightness controls
work under Windows 10/11 with Tianocore payload.
Change-Id: I27d04655adcd4a5dd42b025cfccb508cfd7aaeae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Move includes using library paths to the top and remove unnecessary
comments. Also, get rid of that unnecessary _SB scope. Use an absolute
path for the PCI0 device instead.
Change-Id: I2c4fb1933eda2eb75bfe9181f13e189ec66cadf9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
These statements fit on a single line. Reflow them to ease future works.
Change-Id: Ie18e9a00f67b999fdcedcab3c28b68e34bc93da4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The `CaVrefConfig` FSP-M UPD describes how the on-die Vref generators
are connected to the DRAM. With the exception of an early Skylake RVP
board (which doesn't have coreboot support), mainboards using DDR3 or
LPDDR3 memory should set `CaVrefConfig` to 0, whereas mainboards with
DDR4 should set `CaVrefConfig` to 2. MRC uses this information during
memory training, so it is important to use the correct value to avoid
any issues, such as increased power usage, system instability or even
boot failures.
However, several Skylake DDR4 mainboards don't set `CaVrefConfig` to 2.
Although they can boot successfully, it's not optimal. For boards that
set `DIMM_SPD_SIZE` to 512 (DDR4 SPD size), set `CaVrefConfig` to 2.
Change-Id: Idab77daff311584b3e3061e9bf107c2fc1b7bdf1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
FSP-S hides the PMC from the PCI bus when it runs, but there are still
initialization steps coreboot programs for the PMC. Therefore, change
all of the cannonlake mainboards to set the PMC as hidden in the
devicetree, which means the device will be skipped during enumeration,
but device callbacks are still issued as if the device were enabled.
TEST=Ran full patch train on google/dratini, disassembled SSDT and the
PEPD device matches what is in pep.asl. Also verified via dmesg that the
INT33A1 device is still initialized by the kernel.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib4a20ce9075ce7653388a5d3e281fe774bf89355
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Specify the type of the `DIMM_MAX` Kconfig symbol once.
Change-Id: I2e86baaa8bd50c7b82c399fde5dcea05da6b4307
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Make `mainboard_fill_spd_data` mandatory and adapt mainboards to define
this function accordingly.
Change-Id: Ic18c4c574e8c963bbb41c980f43bdbacc57735af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55806
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `OVERRIDE_DEVICETREE` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I4cbf4e318a30f0cf75aa8690e7454b9caa115c9d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56556
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `DEVICETREE` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If68f11a5ceaa67a3e8218f89e1138c247ebb9a25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56555
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to specify the type of the `CBFS_SIZE` Kconfig symbol
more than once. This is done in `src/Kconfig`, along with its prompt.
Change-Id: I9e08e23e24e372e60c32ae8cd7387ddd4b618ddc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New kconfig parsers interpret $(var) themselves, leading to empty
fields. Old kconfig understands \$(var), so use that.
Change-Id: I927fc9dc7a66211bfe51d4324cf7c51b555ea3a8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55912
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- Add a codec reset before setting the subvendor ID using the Azalia macro
for consistency with all other Realtek HDA codecs
- disable jack detect for the external mic on the 3.5mm jack, since it's not
currently working, so that the external microphone can be manually selected
Change-Id: Ib0f99e5088973a721c0a295899012c9aea5009cf
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
- set subsystem/subvendor ID to Realtek default, as the one dumped
from the vendor UEFI firmware provides no advantages
- fix the number of verb entries, which excluded the 4 following the
pin configs
- issue the reset *before* setting the subvendor, and use the Azalia macro
- disable jack detect for the 3.5mm jack, both line out and mic, since
it's not currently working, so that the outputs can be manually selected
Change-Id: Icd961c3c5aec23cf61d6a9ad65c603c6dc04697a
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable FastPkgCRampDisable for all domains, set SlowSlewRate to fast/16
for all domains. This aligns the settings with the Librem 14.
Test: boot Librem Mini v2, observe high frequency acoustic noise reduced.
Change-Id: I10bc2a3e6b631b8c0b430e204f376aa9a81ac683
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Decrease SA slew rate to match other domains and reduce
high-frequency noise slightly.
Change-Id: I02cd93481f6bfba6249cb338a0e2f47d471a438e
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use hostbridge.asl from Haswell instead of Broadwell. Both files are
equivalent. Then, drop the now-unused hostbridge.asl from Broadwell.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I87d51727b75a9c59e2f5f3ba8d48c575ce93c78c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Tested on Librem Mini v1 (WHL), both DisplayPort and HDMI 2.0 work.
Change-Id: I0da26fef304583eec0375eee2082a9d2ebe27292
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Replace `3` with `SaGv_Enabled`, which has the same value.
Change-Id: I05cfddfefc45ba5bfb0e684445a6d8e02d7865e3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: Ib2625754e7df818e8a6311e649bc357b2093acb4
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is
done") introduced a workaround in coreboot for `soc/intel/cannonlake`
platforms to save and restore GPIO configuration performed by
mainboard across call to FSP Silicon Init (FSP-S). This workaround was
required because FSP-S was configuring GPIOs differently than
mainboard resulting in boot and runtime issues because of
misconfigured GPIOs.
This issue has since been fixed in FSP (verified with FSP v1263 on
hatch). However, there were still 4 boards in coreboot using
`cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u
and system76/lemp9 were tested to ensure that this workaround is no
longer required.
This change drops the workaround using `cnl_configure_pads()` and
updates all mainboards to use `gpio_configure_pads()` instead.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Tested-by: Angel Pons <th3fanbus@gmail.com>
(Tested purism/librem_cnl)
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
(Tested clevo/cml-u which is similar to system76/lemp9)
Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update GPIO config based on review of latest schematics:
- LAN/WLAN reset lines are NC
- SDIO lines configured via GPP_G0-G7
- DMIC lines are wired directly to codec, not PCH, so GPP_D17-20
are set to NC
- Pads GPP_H0-H3 are configured for I2S2
- Pads GPP_H7-H9 are straps for board revision, so treated as GPI
- CPU_C10_GATE# is NC
- PWRBTN# does not need an internal pull-up
- GPP_C20-23 are configured for M.2 UART
- SATAXPCIE1/2 and EC SCI/SMI lines do not need internal pull ups
- GPP_C6/C7 set to I2C1 for future use
- GPP_E15 changed from SCI to SMI, edge triggered
Change-Id: If113cfeadf093e10dd84ab827ead594088f02ba1
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52389
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When a pad is configured as NC, it is set as a GPI with both
TX and RX disabled, and as the pad is internally disconnected,
no pull up or pull down is needed.
Change-Id: Id551b8f6f5b8c772e17670b8b728b5e890ef0b21
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52388
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Port 80 (actually 0x80-0x8f) is a fixed I/O range and thus does not have
to be set up as generic range. Drop the entries from the devicetrees.
Change-Id: I8a54d3c35a321a2d57bd846662f7339eff53e5a8
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The define for color keyboard setting has never been used, as it was
added as a Kconfig selection when ec/system76/ec was introduced.
Change-Id: Iec9134e226382d32783342ef1d37c6f6f6caeb6e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
On production boards, the touchpad interrupt line was moved
from GPP_B20 to GPP_B3. Fix the GPIO pad config and devicetree entry,
and update documentation to remove touchpad config issue.
Change-Id: Iaefeba8f78c567b67e7a416c27299bff574c23ab
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51797
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The 'device pci 00.0 on end' entries are not necessary for socketed
devices unless a chip driver needs to be bound to a device, so remove
them from the devicetree. Also remove the `drivers/wifi/generic` chip
driver as it was not necessary either.
Change-Id: Id5f2e34d98b236f9cfac9f0afd8a8017e349603f
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
On-board devices should be present in the devicetree, so that
`.on_mainboard` field of `struct device` is `1`.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3678514482724377bcdfcbdc7f2c5b312a48b2c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Do not use the same name as the non-LP GPIO config. This allows checking
at build-time that a mainboard uses the correct GPIO config format.
Without this commit, there are no build-time errors when using the wrong
format of GPIO config, but there would be undefined behavior at runtime.
Tested by trying to build asrock/b85m_pro4 and hp/folio_9480m after
toggling the `INTEL_LYNXPOINT_LP` Kconfig option (and trimming down the
USB config arrays for asrock/b85m_pro4). In both cases, building failed
because the necessary GPIO config global is not defined, as expected.
Change-Id: Ib06507ef8179da22bdb27593daf972e788051f3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51661
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for the CometLake-U based Librem 14 laptop.
Change-Id: I24a2a92091cc272638ecaf8ea23a896cab8a7153
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51549
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No need to restrict this further than the platform default,
and will be problematic with the addition of the upcoming
6C/12T Librem 14 board.
Change-Id: I1913992ec12578e1ad3bf6bf679d1a35a46d7370
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make the SATA LED blink when coreboot dies. GPIO functions aren't
compiled in for postcar, so add a check to prevent linker failures.
TEST: Try to boot Librem Mini WHL without RAM, observe blinking (and
also blinding LED). Re-install RAM (and re-seat RAM a few times),
boot to OS, and observe SATA LED operating normally, as expected.
Change-Id: I0ffac0ab02e52e9fbba7990f401d87e50a1b5154
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50013
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Refresh2X to mitigate RAM corruption during long
(> 1hr) periods of S3/suspend, which leads to failure to
successfully resume from S3. Unknown if an issue with all
DRAM types, but tested w/Kingston KVR24S17D8 16GiB DDR4 SODIMMs.
Test: Build/boot Librem Mini v1/v2, put device in suspend,
wait > 1hr, ensure resume from S3 successful 100% of the time.
Change-Id: Ie8e3ebbb1ebdcd98813b5f36f580a235712d2f97
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50756
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
