| Age | Commit message (Collapse) | Author |
|---|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP 2.0 needs to set the ac_loadline and dc_loadline for
each VR config. Without it, the Loadline is considered to be
0 mOhm and this causes CPU temp to jump all over the place
whenever the CPU is used.
This is necessary since there are no VR_CONFIG icc mappings for
Skylake SKUs, only KabyLake.
These values were copied from the Google Poppy devicetree.
Change-Id: I6aeb6ee521988b94f2ae94a60d1a28b87ba984d4
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set the Thermal Control Circuit (TCC) activaction value to 95C
even though FSP integration guide says to set it to 100C for SKL-U
(offset at 0), because when the TCC activates at 100C, the CPU
will have already shut itself down from overheating protection.
This was tested on Purism Librem 13 v2. A bisect showed that the
immediate shutdowns happened after commit [1] was merged which led
to this solution.
[1] ec5a947b (soc/intel/skylake: make tcc_offset take effect)
Change-Id: Idfc001c8e46ed3b07b24150c961c4b9bc9b71a62
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Although VmxEnable is currently ignored by FSP, a forthcoming patch
explicitly enables it in coreboot, so set it in anticipation of that.
Enable Intel SpeedStep to ensure the ACPI tables are generated for
the C-states/P-states which are required for the xen-acpi-processor
module to be loaded. Without it, the Qubes 4.0-rc4 installer will
complain at boot about modules that could not be loaded.
Change-Id: I968ef36ec9382a10db13d96fd3a5c0fc904db387
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the GPIO to match the TPM-enabled motherboards, and add TPM
support in devicetree and enable the config.
After changing the GPIO table, the librem 13v2 and librem 15v3 now
have the same GPIOs, so use a single gpio.h file instead of one
file per variant.
Change-Id: I425654c1c972118aa81c27961246238c2eef782d
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/23683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC needs to set the PPCM value depending on whether
Turbo is enabled or not, and the values differ between
Broadwell (0, 1) and Skylake (1, 2) platforms.
Change-Id: I662dce54415e685c054ffc00b6afde0f1f7765e2
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The LPC I/O ports for EC communication were not set properly,
causing ectool to fail to read the Index I/O from the EC.
The EC Index I/O is on port 0x380 and the LPC I/O port needs to be
decoded by the PCI device for it to be accessible.
Correct the value for the Librem 13v1, 13v2 and 15v3.
Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This speeds up the SPD read ('calling FspMemoryInit' phase) from
218ms to 134ms consistently.
Tested on both the Librem 13 v2 and Librem 15 v3.
Change-Id: I44fbe96c256972bd074537159771d61fe7adf082
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/22969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Make lint-stable was giving an error on this.
Change-Id: I06d11d86151f683b82b6df537e3de8c52d33e8b4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Add new board librem15v3 as a variant of the librem_skl baseboard.
Changes from the librem13v2:
- Change board name and version
- Change GPIO A18, A19, A20, D9, D10 and D11 from NC to GPIO
- Enable PCI device 1c.4
- Change USB port definitions in devicetree
TEST: build w/SeaBIOS, boot PureOS on Librem 15 v3 hardware
Change-Id: I7c762a34f5b961c908e4a29ec331da4b0dea9986
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22048
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Convert the Purism Librem13v2 board to a variant setup,
in preparation of adding the librem15v3 as a new variant.
The 13v2 and 15v3 are nearly identical, so this minimizes new
code to add support for the latter.
Change-Id: I5d648cdb8f63c03de5474253203b3d0853673294
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22047
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
