| Age | Commit message (Collapse) | Author |
|---|
|
Although VmxEnable is currently ignored by FSP, a forthcoming patch
explicitly enables it in coreboot, so set it in anticipation of that.
Enable Intel SpeedStep to ensure the ACPI tables are generated for
the C-states/P-states which are required for the xen-acpi-processor
module to be loaded. Without it, the Qubes 4.0-rc4 installer will
complain at boot about modules that could not be loaded.
Change-Id: I968ef36ec9382a10db13d96fd3a5c0fc904db387
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the GPIO to match the TPM-enabled motherboards, and add TPM
support in devicetree and enable the config.
After changing the GPIO table, the librem 13v2 and librem 15v3 now
have the same GPIOs, so use a single gpio.h file instead of one
file per variant.
Change-Id: I425654c1c972118aa81c27961246238c2eef782d
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/23683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The LPC I/O ports for EC communication were not set properly,
causing ectool to fail to read the Index I/O from the EC.
The EC Index I/O is on port 0x380 and the LPC I/O port needs to be
decoded by the PCI device for it to be accessible.
Correct the value for the Librem 13v1, 13v2 and 15v3.
Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/25328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Convert the Purism Librem13v2 board to a variant setup,
in preparation of adding the librem15v3 as a new variant.
The 13v2 and 15v3 are nearly identical, so this minimizes new
code to add support for the latter.
Change-Id: I5d648cdb8f63c03de5474253203b3d0853673294
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22047
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
