| Age | Commit message (Collapse) | Author |
|---|
|
In RS485 mode RTS line acts as a transceiver direction control.
The datasheet is not very clear about the polarity but register setting
here is tested to drive nRTS line high when transmitting.
Also note revision of B of the super-IO has errata and 8N1 setting does
not work properly, you would need revision C of the chip assembled to
fix this.
Change-Id: I705fe0c5a5f8369b0a9358a64c74500238b5c4ba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14998
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Idc29373cb01f4304d22ae315812bd40f0aaa94c9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16729
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia1f24d328a065a54975adde067df36c5751bff2d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15987
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Run the command below to format the files `irq_tables.c` of (mostly AMD)
mainboards correctly with GNU indent 2.2.10.
```
$ git grep -l 'if (sum != pirq->checksum) {' | xargs indent -l
```
Fix up the following two checkpatch.pl errors manually.
```
ERROR: that open brace { should be on the previous line
#1219: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:129:
+ uint8_t reg[8] =
+ { 0x41, 0x42, 0x43, 0x44, 0x60, 0x61, 0x62, 0x63 };
ERROR: that open brace { should be on the previous line
#1221: FILE: src/mainboard/gigabyte/ga_2761gxdk/irq_tables.c:131:
+ uint8_t irq[8] =
+ { 0x0A, 0X0B, 0X0, 0X0a, 0X0B, 0X05, 0X0, 0X07 };
```
This is needed, so that follow-up commits, fixing checkpatch.pl errors
and warnings, won’t run into conflicts with the git commit hooks, when
for example, spaces instead of tabs are used for indentation.
Change-Id: If254723f3013377fb3b9b08dd5eca6b76730ec4a
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/15932
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Boards incorrectly used intel include file for AMD board.
Change-Id: I6d3172d1aa5c91c989a6ef63066a7cd6f70013f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15232
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Just the memory size, there is no strap to identify PCB revision.
Change-Id: I65b2f5b0ac6930bead60ea0a551f13a6bcab24c7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14997
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The way dispatcher table is set up prevents linker from
optimizing unused code away, we currently have raminit in ramstage.
Optimize this manually by configuring AGESA_ENTRY booleans for
romstage and ramstage separately. This will remove references in
FuncParamsInfo and DispatchTable -arrays.
All boards now include multi-core dispatcher, it has minimal footprint:
AGESA_ENTRY_LATE_RUN_AP_TASK
ACPI S3 support depends on HAVE_ACPI_RESUME being enabled:
AGESA_ENTRY_INIT_RESUME
AGESA_ENTRY_INIT_LATE_RESTORE
AGESA_ENTRY_INIT_S3SAVE
Disabled for all boards as it was not used:
AGESA_ENTRY_INIT_GENERAL_SERVICES
Change-Id: I7ec36a5819a8e526cbeb87b04dce4227a1689285
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14417
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add APU1 prefix because Kconfig throws errors if we try to
define the same variables as choice-entry for APU2 board.
Change-Id: Ic071600dd88e391a8a278d63aad13abd01fd3c9d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14988
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
File buildOpts.c is a can of worms, pull platform memory
configuration in to OemCustomize.c. This array should be
assigned at runtime instead of linking a modified defaults
table.
Change-Id: I73d9d3fbc165e6c10472e105576d7c40820eaa6a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There are other things besides PCIe port configuration that
require board specific hooks.
Change-Id: I0923651487b9ed5f6f7569ce08e02d993fa5f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14527
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The two external USB ports and the internal USB header have overcurrent
protection chips with the low-active overcurrent signal connected to the
chipset.
The power-on default for this register disables the software detection
of overcurrent conditions.
After setting the register Linux correctly shows the overcurrent
condition in the kernel log (tested by shorting the 5v and gnd lines on
J14 / the internal USB header):
[ 2015.229921] usb usb1-port3: over-current condition
[ 2015.449925] usb usb1-port4: over-current condition
Simlar for the external ports:
[ 256.237916] usb usb1-port1: over-current condition
[ 256.458084] usb usb1-port5: over-current condition
Note that each signal is shared between two ports:
usboc0#: External ports (port1/5)
usboc1#: Internal ports (port3/4)
Change-Id: I02d498053b8ec61dc206e74a96c4a1dcfd4fae92
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/14084
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The newer versions of IASL are unhappy when an operator
has the same object as both source and destination.
The warning can be completely disabled with a command
line argument, but in general, I'd really rather not
just disable warnings.
The bits in this register are write 1 to clear, so reading and
writing the same register is what we want to do. Instead, store
it in a temporary register then write it in a second operation.
Fixes warning:
dsdt.aml 1396: Store(PWST, PWST)
Warning 3023 - ^ Duplicate value in list
(Source is the same as Target)
Change-Id: I52d73d4431db237be83016d67cd397f31b53d9c6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12691
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The _HID was present for the top level BTNS and LEDS Devices, but
was missing in the individual devices.
The alternative would be to supply the GPIO being used as an _ADR
object, but since it looks like the driver already has another
method of handling that, it isn't required.
Fixes these IASL warnings:
dsdt.aml 1522: Device (BTN1)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1567: Device (LED1)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1576: Device (LED2)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
dsdt.aml 1587: Device (LED3)
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
Change-Id: I67c48084a6ee2a104ffff2b5a986d24a51ee49e1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12582
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've actually got more warnings now than when I first tested IASL
warnings as errors. Because of this, I'm adding it with the option
to have it disabled, in hopes that things won't get any worse as we
work on fixing the IASL warnings that are currently in the codebase.
- Enable IASL warnings as errors
- Disable warnings as errors in mainboards that currently have warnings.
- Print a really obnoxious message on those platforms when they build.
***** WARNING: IASL warnings as errors is disabled! *****
***** Please fix the ASL for this platform. *****
Change-Id: If0da0ac709bd8c0e8e2dbd3a498fe6ecb5500a81
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
only enable pcie gpp clocks when the corresponding clkreq pin is asserted
Change-Id: I7822d011bb94867d470c0194e6b652833c395cb2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12353
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
disable unconnected FCH clock outputs to save some power
Change-Id: Ib3efebb8656392d58d762c23827168017d273de8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12082
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All the deleted mainboard files contain no code besides some print
statements denoting, that the init is executed.
If such statements are desired, this should be done in common code so it
does not have to be added to each mainboard.
Therefore, also delete files with just print statements.
Change-Id: I379e4b1e1b1725648c6231bc6954ac3cc655a596
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/12355
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I0f3297dff47dfb44da034ac6f305dcf1981b9de1
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11080
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I09d2449af9c1562f4f3d5af1e8764b82b6550007
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: http://review.coreboot.org/12223
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Serial number is derived from the MAC address of first NIC.
Change-Id: I91e5555b462cca87d48fb56c83aedd1eb02eba62
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11901
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
Do this to wipe error message and hexdump of SPD from console log.
Change-Id: I45ffcb1c80aecf43b79d93faedcd62c8f0023cb7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11900
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Value of tRFCmin was incorrectly using 2 Gigabit chip data.
There was no observed instability or bug reports because of this.
Change-Id: Ifa03b883afa5a304dd20caf3d4d0383c6cfebdb8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/11899
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Inspired by the Sage source code (itself from coreboot).
Change-Id: I4864923166efb200882d895c572d1ee060c71951
Signed-off-by: Maxime de Roucy <maxime.deroucy@gmail.com>
Reviewed-on: http://review.coreboot.org/11730
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The thermal sensor interface exposed in function 3 of the northbridge is
a more convenient and faster way to access the processor-internal
thermal sensor than using the SMBus/SB-TSI interface from the FCH, see
the Family14 BKDG: "Tctl is a processor temperature control value used
for processor thermal management. Tctl is accessible through SB-TSI and
D18F3xA4[CurTmp]. Tctl is a temperature on its own scale aligned to the
processors cooling requirements"
Also on at least some of these boards the existing thermal zone is
broken and always returns 40C (the default value if the SMBus read
failed) because the SMBus muxing register (SmBus0Sel) is not set up
correctly.
Case in point: The fallback "smbus read failed" temperature is 40 C and
the the logs taken from the board status repository for the Asrock
E350M1 board all show: "ACPI: Thermal Zone [TZ00] (40 C)"
e.g.
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-5054-gf584218/2013-12-20T20:56:20Z/kernel_log.txt#l390
and
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-7030-g6d7de4f/2014-10-16T15:34:19Z/kernel_console.txt#l404
and
http://review.coreboot.org/gitweb?p=board-status.git;a=blob;f=asrock/e350m1/4.0-9989-gf2dfef0/2015-06-13T00:22:49Z/kernel_log.txt#l425
Example lm-sensors output with this patch on the pcengines APU1, on
Linux 4.1.0-rc8+ (wiht both CONFIG_ACPI_THERMAL and
CONFIG_SENSORS_K10TEMP enabled):
acpitz-virtual-0
Adapter: Virtual device
temp1: +54.0 C (crit = +100.0 C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +54.0 C (high = +70.0 C)
(crit = +100.0 C, hyst = +97.0 C)
Change-Id: Id9c5b783ba424246816677099ec6651814e59f21
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10940
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Instead of reaching into src/include and re-writing code
allow for cleaner code sharing within coreboot and its
utilities. The additional thing needed at this point is
for the utilities to provide a printk() declaration within
a <console/console.h> file. That way code which uses printk()
can than be mapped properly to verbosity of utility parameters.
Change-Id: I9e46a279569733336bc0a018aed96bc924c07cdd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11592
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The APU1 board has no IDE port, remove ide.asl.
Change-Id: I76b926969748de79ac1281ed50b37e9ade1a6771
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10622
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Iacad070f43534a8b27a2473a6a2854bc2f6e607a
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/10598
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Provide ACPI devices with devicetree-compatible annotations for the
three leds and the button of the APU1, as well as the GPIO driver.
This will cause the Linux kernel to automatically load the following
modules:
leds_gpio (CONFIG_LEDS_GPIO)
gpio_keys_polled (CONFIG_KEYBOARD_GPIO_POLLED)
gpio_sb8xx (CONFIG_GPIO_SB8XX)
See
http://events.linuxfoundation.org/sites/events/files/slides/ACPI_vs_DT.pdf
and https://lwn.net/Articles/612062/ for some more information on how
the PRP0001 HID works.
To make this usable a Linux GPIO driver for the AMD chipset is also
required, which I am currently working on, but have not submitted
upstream yet.
Leds have been named after the convention in
Documentation/leds/leds-class.txt:
LED Device Naming
=================
Is currently of the form:
"devicename:colour:function"
For comparison, on an OpenWRT device:
GPIOs 0-21, ath79:
gpio-1 (tp-link:green:usb ) out hi
gpio-2 (tp-link:green:system) out lo
gpio-3 (reset ) in hi
gpio-5 (tp-link:green:qss ) out lo
gpio-7 (qss ) in hi
gpio-9 (tp-link:green:wlan ) out lo
gpio-18 (rtl8366rb ) in hi
gpio-19 (rtl8366rb ) in hi
On the apu1:
GPIOs 288-511, platform/PRP0001:00, AMD SB8XX/SB9XX/A5X/A8X GPIO driver:
gpio-475 (switch1 ) in hi
gpio-477 (apu1:green:led1 ) out hi
gpio-478 (apu1:green:led2 ) out hi
gpio-479 (apu1:green:led3 ) out hi
Change-Id: I956ee92d9d98ef27a83ccb30d314543bd8634f2c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10540
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The smbus.asl operation regions prevent the Linux i2c driver (i2c_piix4)
for this chipset from claiming the ioport ranges and thus it fails to
load.
The methods defined in smbus.asl are not used in the DSDT and also don't
exist in the DSDT of the vendor firmware.
In particular due to the following check in i2c-piix4.c will fail unless
acpi_enforce_resources=no is explicitly set on the Linux kernel
parameters:
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
Depending on kernel options the only error message printed is
ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B07 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0B (\SMB0) (20150410/utaddress-254)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
However since it does not implement a standard interface there is no
native ACPI driver for smbus.asl.
Change-Id: Id8401e8b36f0e2412d490a92c20540a04d853125
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: http://review.coreboot.org/10539
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Note: apu1c models do not support this. That we expose S3 in
ACPI table while it is not available, is a wider issue to solve.
Change-Id: I9b07550d0523593f51c1882a40cccd783115057b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10315
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Same comments were already removed for the latest board, the amd/lamar.
Change-Id: Ie244f838409c567c11f7444c9cf17de72e49dbb0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10283
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
These are alternative customer options connected to J19 header.
We need to avoid modifying devicetree.cb, so we fix devicetree
for the super-io device-enables at runtime instead.
Change-Id: I04a79974b9bdf52b09ffc1b1362e201eab1ee011
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10178
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These tables are not referenced anywhere, thus all
comments about adjustments are void.
Also drop stub AgesaReadSpd that is all commented out.
Change-Id: I12233ea0dc4baaf36a75f359c52cc59c9b6dad79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10143
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
This change switches all southbridge vendors and southbridges
to be autoincluded by Makefile.inc, rather than having to be
mentioned explicitly in southbridge/Makefile.inc or in
southbridge/<vendor>/Makefile.inc.
In order to be able to drop southbridge/amd/Makefile.inc, some
scattered source files had to be moved to a southbridge/amd/common
directory, in accordance to what we are doing on other architectures
already.
This means, vendor and southbridge directories are now "drop
in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree components to be
built with a given coreboot version (given that the API did not
change).
Change-Id: I79bd644a0a3c4e8320c80f8cc7a7f8ffd65d32f2
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/9796
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
echo is evaluated by a shell builtin producing non-binary
spd data of the form '-e -n \<byte>'. Correct this by
using printf builtin which does the equivalent and is
more cross platform friendly.
Boards changed:
gizmosphere/gizmo
gizmosphere/gizmo2
google/bolt
google/falco
google/link
google/peppy
google/rambi
google/samus
google/slippy
pcengines/apu1
Change-Id: Iefdaf59903b9682cc88c94fd991883b560616492
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9196
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These binaries were being added to CBFS using hexadecimal values instead
of the CBFS binary type names. The same value was being used in
different places for different things.
For example, the value 0xAB is used for SPDs, MRC & FSP binaries.
This patch uses CBFS type names instead of hex values everywhere a
hex value was previously used.
Change-Id: Id5ac74c3095eb02a2b39d25104a25933304a8389
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/8978
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
We do not allow platforms to mess around with memory layout.
Change-Id: I316ff522c8833fa3b7ad20f2c5a9cae21f4174d8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change gpp_configuration to GPP_CFGMODE_X1111 (was X4000), this is done
to only advertise x1 lane width for PCIe link 0:15.0.
Hide functions of PCIe links that have no slots connected. Our PCI
infrastructure does not support bridge devices that are set off
in devicetree but remain visible in the PCI hardware tree.
Change-Id: If90919634995076ab0f029baece3ba9cb8f3f3b2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8388
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Remove functions 0:12.1 and 0:13.1 that do not exist in the hardware.
Disable 0:14.1 IDE controller, as it would only be used with SATA ports
4 and 5 that are not populated with connectors in the hardware.
Disable 0:14.2 HD audio, as it is not implemented in the hardware
Disable 0:14.5 OHCI controller, as ports behind this USB1.1 -only controller
are not populated in the hardware.
Fix some alignment and whitespace.
To my knowledge these changes are not included with SAGE release
pcengines.apu_139_osp.tar.gz, but that tarball does not contain
either devicetree.cb or a pre-compiled static.c file so I cannot tell
for sure.
Change-Id: Idcb8e76645fce7e89a37ff7007531b668f472131
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8328
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Interrupts from USB controllers 0:16.0 and 0:16.2 were not routed
in PIC mode. The only affected peripheral was the SD card reader.
This patch is not included with SAGE release pcengines.apu_139_osp.tar.gz.
Change-Id: Ie7f0fa3751b46cca0132bd6dcada3628c6a45efb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8327
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Some GPIO pins are shared with (disabled) PCI bridge 0:14.4.
As our PCI subsystem currently does not configure PCI bridges that are
marked disabled, but remain visible in the hardware, we cannot mark 0:14.4
disabled in devicetree just yet.
Change-Id: Ibc5d950662d633a07d62fd5a5984a56d8e5f959d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8326
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
While we cannot recreate exact copies of PC Engines APU1 firmware images,
I shall upstream the vital changes for coreboot from the following tarballs
SAGE has published to meet GPL:
SageBios_PCEngines_APU_sources_for_publishing_20140405_GPL_package.tar.gz
md5sum: ce5f54723e4fe3b63a1a3e35586728d4
pcengines.apu_139_osp.tar.gz
md5sum: af6c8ab3b85d1a5a9fbeb41efa30a1ef
The patch here adds Kconfig, Makefile.inc and devicetree.cb files to
match 2014/04/05 release tarball config.h and static.c files.
Change-Id: Id61270b4d484f712a5c0e780a01fc81f1550b9ad
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8325
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Drop persimmon customization for superio, azalia, PCI-e reset etc.
Change-Id: I35f49ca67e6cc2df826f24e5a4bb3db5bb6f711e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8324
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I19d6b56e3ac5e6e7946648b97c86a223b748e3bd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8460
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Icebc12d8f83494150a7bdd3adcc168d7b48b2e68
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8458
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iccad79c142a7fcf89dd0fbebe8c07ad9ef019e91
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8459
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Because we had no stack on romcc boards, we had a separate, not as
powerful clone of printk: print_*. Back in the day, like more than
half a decade ago, we migrated a lot of boards to printk, but we never
cleaned up the existing code to be consistent. instead, we worked around
the problem with a very messy console.h (nowadays the mess is hidden in
romstage_console.c and early_print.h)
This patch cleans up the mainboard code to use printk() on all non-ROMCC
boards.
Change-Id: I2383f24343fc2041fef4af65d717d754ad58425e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/8111
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
Fix system include paths to be consistent. Chipset support is
part of the Coreboot 'system' and hence 'non-local' (i.e., in
the same directory or context). One possible product of this, is
to perhaps allow future work to do pre-compiled headers (PCH) on
the buildbot for faster build times. However, this currently just
makes mainboard's consistent.
Change-Id: I2f3fd8a3d7864926461c960ca619bff635d7dea5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8085
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
There were instances of unneeded arch/hlt.h includes,
various hlt() calls that weren't supposed to exit (but
might have) and various forms of endless loops around
hlt() calls.
All these are sorted out now: unnecessary includes are
dropped, hlt() is uniformly replaced with halt() (except
in assembly, obviously).
Change-Id: I3d38fed6e8d67a28fdeb17be803d8c4b62d383c5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7608
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This header has nothing to do with cache-as-ram. Therefore, 'car'
is the wrong term to use. It is about providing a prototype for
*romstage*.
Change-Id: Ibc5bc6f3c38e74d6337c12f246846853ceae4743
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/6661
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
When passing '-ffreestanding' the 'main' romstage.c may no longer
necessarily be considered the entry point.
From the C specification in 5.1.2.1 Freestanding environment;
"In a freestanding environment (in which C program execution may take
place without any benefit of an operating system), the name and type of
the function called at program startup are implementation-defined."
Clang complains about these being missing as Clang is somewhat more
strict about the spec than GNU/GCC is. An advantage here is that a
different entry-point type-signature shall now be warned about at
compile time.
Change-Id: I467001adabd47958c30c9a15e3248e42ed1151f3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5872
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: If29a70be4fb56ebb0dbf6d510412cbe2f34480ef
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6291
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I05d6d22664155ac8478e665733f816776e277c22
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6200
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Move towards the removal of the superio model specific xxx_serial_enable
implementation. Make remaining superio romstage parts link-time symbols
and fix corresponding mainboards to match.
The following mainboards remain unconverted as they are ROMCC:
- mainboard/supermicro/x6dai_g
- mainboard/supermicro/x6dhe_g
- mainboard/supermicro/x6dhr_ig
- mainboard/supermicro/x6dhr_ig2
and so block the final removal of w83627hf_serial_enable().
Special cases:
- mainboard/supermicro/h8qme_fam10: Provide local pnp_ sio func
Provide local superio pnp_ programming entry/exit functions as to avoid
making superio implementation global symbols. Although this is not the
proper/final solution, it does mitigate possible symbol collisions and
allow for continued superio refactorisation.
Change-Id: Iaefb25d77512503050cb38313ca90855ebb538ad
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5601
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I24b2cbd671ac3a463562d284f06258140a019a37
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
According to vendor (Pascal Dornier) they're the same from coreboot
perspective.
Change-Id: I43aeb77f21c251b3d9c5c2dcfa01d4d1de0bc87b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5114
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I4e56f6b37314bff569728b732b4115fb940f70dd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4756
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
board_info.txt is a file to be used by board-status to add
some useful info to the generated table like flash chip type.
This series is autogenerated from wiki page Supported_Motherboards.
Change-Id: Ie2bda900713ef4883134477163320936c84c34f5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4701
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
After Booting the BIOS, flashing coreboot
and booting coreboot with that patch we have:
# ./nvramtool -a
boot_option = Fallback
last_boot = Fallback
ECC_memory = Disable
baud_rate = 115200
power_on_after_fail = Disable
debug_level = Spew
boot_first = HDD
boot_second = Fallback_Floppy
boot_third = Fallback_Network
boot_index = 0xf
boot_countdown = 0x7f
nvramtool: Warning: Coreboot CMOS checksum is bad.
Change-Id: Ia87b09003d859f6dee7c09aa963df002c1d02688
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3323
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I249c63646267ebe8dd8e06980aa6367a16fe7297
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3370
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ie329606852dfd7109acb694e9a9ff851b023cc63
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3369
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Move the include before static inline int spd_read_byte().
Change-Id: I4cac4b1f55368041b067422d95c09208e15d0f2d
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3368
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Revert commit f90071faeee3358748d0c8d31e46721b53241e28 [1] as
it was merged without its dependencies and therefore the source
tree currently does not build [2][3].
OPTION option_table.h
GEN build.h
SCONFIG mainboard/pcengines/alix1c/devicetree.cb
CC arch/x86/lib/cbfs_and_run.romstage.o
CC arch/x86/lib/memcpy.romstage.o
CC arch/x86/lib/memset.romstage.o
CC arch/x86/lib/rom_media.romstage.o
CC arch/x86/lib/romstage_console.romstage.o
CC console/die.romstage.o
CC console/post.romstage.o
CC console/vtxprintf.romstage.o
CC device/device_romstage.romstage.o
CC lib/cbfs.romstage.o
CC lib/compute_ip_checksum.romstage.o
CC lib/gcc.romstage.o
CC lib/lzma.romstage.o
CC lib/memchr.romstage.o
CC lib/memcmp.romstage.o
CC lib/memmove.romstage.o
CC lib/ramtest.romstage.o
CC lib/uart8250.romstage.o
CC southbridge/amd/cs5536/smbus.romstage.o
ROMCC generated/bootblock.inc
GEN generated/bootblock.ld
make: *** No rule to make target `nvramtool', needed by `coreboot-builds/pcengines_alix1c/coreboot.pre1'. Stop.
make: *** Waiting for unfinished jobs....
OPTION cmos_layout.bin
[1] http://review.coreboot.org/#/c/3229/
[2] http://www.coreboot.org/pipermail/coreboot/2013-May/075864.html
[3] http://qa.coreboot.org/job/coreboot-gerrit/6251/testReport/junit/(root)/board/i386_pcengines_alix1c/
Change-Id: I4764d90c39ccdb4dc7e7a9aef7525c306614e1a8
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3245
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
After removing power and the CMOS Battery, putting it back
and booting coreboot we have:
# ./nvramtool -a
boot_option = Fallback
last_boot = Fallback
ECC_memory = Disable
baud_rate = 115200
power_on_after_fail = Disable
debug_level = Spew
boot_first = HDD
boot_second = Fallback_Floppy
boot_third = Fallback_Network
boot_index = 0xf
boot_countdown = 0x7f
nvramtool: Warning: Coreboot CMOS checksum is bad.
Change-Id: Iba2701d4611cd2c2e5a2d76d41ffc23ed65574e8
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3229
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
To reduce the differences between these file name the enabling
device function in the directory `src/mainboard` uniformly
`mainboard_enable` [1].
Thanks to the awesome help of gnomon and BlastHardcheese in the
IRC channel #sed on <irc.freenode.net>. gnomon came up with the
following command to do the actual work.
$ cd src/mainboard
$ for f in */*/mainboard.c ; \
> do src="$(awk '/\.enable_dev = /{v=$NF; sub(/,$/,"",v); print v}' "$f")" ; \
> [[ -z $src ]] && continue ; \
> printf '%s\n' "g/${src}/s/${src}\([,(]\)/mainboard_enable\1/p" w | ed -s "$f" ; \
> done
`src/mainboard/digitallogic/msm586seg/mainboard.c` and
`src/mainboard/technologic/ts5300/mainboard.c` had to be adapted
manually as no comma was used separating the struct members.
And with the following statement, gnomon is even more likable!
My pleasure entirely. Good luck with coreboot; I'm a big fan of the project.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074548.html
Change-Id: Ife9cd0c2d9cc1ed14afc6d40063450553f06a6c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2493
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
intel_irq_routing_table is a local structure that should not be used
globally, because it might not be there on all mainboards.
Instead, the API has to be corrected to allow passing a PIRQ table in
where needed.
Change-Id: Icf08928b67727a366639b648bf6aac8e1a87e765
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1862
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
mainboard_config never worked right, at least not since we've had sconfig.
Hence, drop mainboard/<vendor>/<device>/chip.h and fix up the mainboards that
tried to use it anyways.
Change-Id: I7cd403ea188d8a9fd4c1ad15479fa88e02ab8e83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1359
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
LX has two values that are usually automatically derived but can
be overridden, that were so far defined in each board's romstage.
These values, along with the toggle to enable override are now
part of LX's Kconfig. For boards that gave values but requested
autogeneration, the values are removed.
Further improvements: Figure out the various fields in PLLMSRlo
and make them sensible Kconfig options (instead of the hex value
it is now)
Change-Id: I8a17c89e4a3cb1b52aaceef645955ab7817b482d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1227
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The Alix6 is very similar to the alix2, differing in having 1 mini-PCIe
slot (USB 2.0 only), an RFKILL GPIO line going to that slot, and 1 or 2
SIM sockets.
Change-Id: I19e4e756966e60bb0310c19286654d3d579b8850
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Reviewed-on: http://review.coreboot.org/521
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Kconfig directives to select chip drivers for compile literally
match the chip directory names capitalized and underscored.
Rename directories and Kconfig as follows:
model_lx -> geode_lx
model_gx1 -> geode_gx1
model_gx2 -> geode_gx2
Change-Id: Ib8bf1e758b88f9efed1cf8b11c76b796388e7147
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/613
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Coming changes to abuild require that VENDOR_ and BOARD_ names have
common suffixes.
Change-Id: I44cf759dd3b2d02c525eb325dc9c5c989f172ac5
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Reviewed-on: http://review.coreboot.org/548
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
initialization functions.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6531 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6487 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6149 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Some mainboards need to disable the power button to avoid turning off
right after being turned on, while other boards ship with a jumper over
the power button and should allow the user to configure the behavior.
This adds infrastructure in the form of four mutually exclusive options
which can be selected in a mainboard Kconfig (power button forced on/off,
and user-controllable with default on/off) and one result bool which
source code can test. (Enable the button or not.)
The options have been implemented in CS5536 code and for all mainboards
which select SOUTHBRIDGE_AMD_CS5536, but should be used also by other
chipsets where applicable. Note that if chipset code uses the result
bool ENABLE_POWER_BUTTON, then every board using that chipset must
select one out of the four control options in order to build.
All touched boards should have unchanged behavior, except
pcengines/alix1c, traverse/geos and lippert/hurricane-lx where the
power button can now be configured by the user.
Build tested for alix1c, alix2d, hurricane-lx and wyse-s50. Confirmed
to work as advertised on alix1c both with button enabled and disabled.
Includes additional traverse/geos changes from Nathan and
lippert/hurricane-lx changes from Jens to correctly use the new
feature on those boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Remove many more .c-includes from i945 based boards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
configs. I just moved it the the CPU that they all use.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested using abuild.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5844 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5823 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
coreboot_ram can be unpacked to 1MB. The value is quickly
replaced with the real value later, thus causing no harm.
Move RAMBASE to the default of 1MB for the affected boards
Signed-off-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5779 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
