| Age | Commit message (Collapse) | Author |
|---|
|
Replace the mainboard-specific code for "POST complete" signalling with
devicetree entries for using the newly introduced IPMI driver
functionality.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Change-Id: I3441c2a971cfb564b34b3a419beceb949fe295b1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This is required for CbNT.
Change-Id: I565a95cd2e76cb1c648884be6d1954288f6e4804
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This fixes ocp/tiagopass not booting as after FSP-S the P2SB is
accessed to read out or reconfigure the HPET and PCH IOAPIC BDF.
Change-Id: Ia37bd0f14627980345cd07f20e935a10d4760b69
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48654
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Delta Lake DVT, dump GPIO settings from UEFI firmware for new PCH
(C621A) by util/inteltool and generate the header file by util/intelp2m.
The DVT and EVT GPIO configurations are the same.
The initial value of GPP_B20 (POST complete) should be high, otherwise
BIC would get incorrect sensor readings and see events like PCH prochot.
Tested=On OCP Delta Lake DVT, dump GPIO configurations
by Intel ITP and verify the results match with the header file.
Change-Id: Ic9837a22bc231a4cb919de316ff6f6ee88411ab8
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47229
Reviewed-by: Tim Chu <Tim.Chu@quantatw.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The xeon_sp ACPI NVS and ramstage NVS were out of sync. Since there
isn't anything uncommon with the soc NVS, use the Intel common NVS.
This covers the NVS cases of common code used by xeon_sp. Update
the mainboards for this change.
Change-Id: Icf422f5b75a1ca7a3d8f3d63638b8d86a56fdd7b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
|
|
Update port connector information for Delta Lake.
Tested=Execute "dmidecode -t 8" to check all the information of
SMBIOS type 8 is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I880bb9a5a41077172423f78b56c19aadd93e001f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
RasModesEnabled
Use RasModesEnabled from SystemMemoryMapHob to define SMBIOS type
16 error correction type
Tested=Execute "dmidecode -t 16" to check if error correction type
is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I3636fcc4a874261cf484c10e2db15015ac5d7e68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Override SMBIOS type 4 cpu voltage. For Delta Lake, 1.6V is expected.
Tested=Execute "dmidecode -t 4" to check if cpu voltage is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I0ecbec8fb3dc79b8c3f3581d6193aade01bcd68e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Use the xeon_sp pch.asl to include the intel common lpc.asl.
Change-Id: I22ee9d325888808a9c775ecee0591b661e2bba4e
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Javier Galindo <javiergalindo@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use the xeon_sp pch.asl to pickup the common block lpc.asl. This
allows deltalake to pick up any general pch asl updates. Currently,
generates the same asl.
Change-Id: I5005032b030d288fdf5ca2f99d21fe8e6c752037
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47304
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The BMC isn't always ready in 60 seconds if it printing debug output.
Give it 90 seconds to finish before timing out in coreboot.
Change-Id: I3932d3e8fad067e8971e82b45b499801fc78079f
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Javier Galindo <javiergalindo@sysproconsulting.com>
|
|
Intel CPX-SP FSP ww45 release annotates default values for FSP-M UPD
variables.
FSPM MemRefreshWatermark option support is present in FB's CPX-SP
FSP binary, but not in Intel's CPX-SP FSP binary. In FB's CPX-SP
FSP binary, this option takes the space of UnusedUpdSpace0[0].
For DeltaLake mainboard, if corresponding VPD variable is set, use it
to control the behavior. Such control is effective when FB's CPX-SP
FSP binary is used.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I57ad01f33b92bf61a6a2725dd1cdbbc99c02405d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46640
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Generated build/dsdt.dsl files are same.
Change-Id: I5bd8fe629fb969ec14dd400b6463ee1592d6903b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46207
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated build/dsdt.dsl files are identical.
Change-Id: Iffd6954dcb3f9fb8bcd89854d84f6944cb520dd1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46208
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6a16e2f829219f2eba8acd3ae7f371238c0d8de1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
The corresponding devices and objects are already included in the
System Bus ACPI scope inside uncore.asl. There is no need to do this
again in the DSDT of the motherboard.
Change-Id: I98a8d60b585e2eafd76948baea0f249a029bae09
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Rename motherboard_fill_fadt() to the common override
mainboard_fill_fadt() function to override FADT.
Tested=On OCP Delta Lake, verify FADT PM Profile is set to
Enterprise Server.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: Ie9ea7cc6e712d0aca57bbeac1a4154921d123be4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested=On OCP Delta Lake, log level can be changed via VPD.
Change-Id: I36d4b01b6fb6acc726749641df089cb3f9a4dc3e
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
In deltalake, there's no embedded controller and BMC version is
used to represent ec version.
TEST=Build with CB:45138 and CB:46070
Execute "dmidecode -t 0" to check if the firmware version is correct
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I388efd749170f0ebbb4dd4d32199675d92cc018e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Update Slot Designation strings and add SSD0_M2_Boot_Drive for config A.
TEST="dmidecode -t 9" to verify the results are expected.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: I3fc03a14ff7dc43d6ddf5aa36710c99dbc648afa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested on OCP deltalake. The console now shows up on the serial.
Change-Id: If4c412c1ca749f1feba47b2ce0beb52d0111be86
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Override smbios_fill_dimm_locator for type 17 Locator and Bank Locator.
Also remove CONFIG(GENERATE_SMBIOS_TABLES) compile option because SMBIOS
is always enabled and it makes the code cleaner.
One sample type 17 table displayed as below:
Handle 0x0010, DMI type 17, 40 bytes
Memory Device
...
Locator: DIMM F0
Bank Locator: _Node0_Channel5_Dimm0
Tested=On OCP Delta Lake, the Locator and Bank Locator strings
are expected.
Change-Id: I84531f9ee8bc76d9529aa983bc13e64f40c93138
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move and use the common xeon_sp/cpx/acpi asl for skx/.
There were only minor whitespace differences between the directories.
Update the mainboards to build the moved files.
TiogaPass coreboot.rom checked with BUILD_TIMELESS.
Change-Id: I5058a3fe8d96075a266fb92f10707bb94308c85b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45217
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCH LPC device is on CSTACK. Add LPC ACPI device entry.
Without this change, following error message shows up in target OS
boot log:
ACPI BIOS Error (bug): Failure looking up [\_SB.PCI0.LPCB], AE_NOT_FOUND (20180105/dswload-211)
ACPI Error: AE_NOT_FOUND, During name lookup/catalog (20180105/psobject-252)
ACPI Error: AE_NOT_FOUND, (SSDT:COREBOOT) while loading table (20180105/tbxfload-228)
ACPI Error: 1 table load failures, 1 successful (20180105/tbxfload-246)
Also TPM device is not created.
TESTED=Booted DeltaLake DVT, run following command in target OS:
[root@dhcp-100-96-192-153 ~]# dmesg | grep tpm
[ 7.331890] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0x1B, rev-id 16)
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I8614f6951389bd5c8f8f33522d0a9a9160ac3f66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I278fb20aa176bb09f1ff135fdfd732f0096d3808
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is selected by Xeon SP Kconfig already.
Change-Id: If1ef7f86b27d7be74912c9ad1f9c1efbda6233e5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Change-Id: I6eaaf80dd2bd69096574ab967ec0c6738b05903b
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested=On OCP Delta Lake, with FSP WW36 dmidecode -t 11 can see the
SPD register vendor ID
String 7: b300 0000 b300 0000 b300 0000 b300 0000 b300 0000 b300 0000
Change-Id: I15ab9b4c709eb97a03d6e08fe0bcdcb7f8607db0
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested on OCP Delta Lake, with FSP WW34 DCI can be connected if enabled.
Change-Id: I8e0dff921cef02dfc66467a2b8fa3e196fb36ac2
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Kconfig 5.8 interprets $(...) itself using environment variables, which
generally means that they expand to the empty string. \$(...) works
with both our current and new Kconfig with the desired behavior
(to pass it through unmodified).
Change-Id: I726567eeb61d2035560152677d2b4548c1472be9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44584
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update devicetree.cb to configure VT-d to be enabled.
TESTED=booted on DeltaLake config A server, and verify DMAR table.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I7d76cd9d50d3e69a4919de281f11d30851bffa3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
coherency_support and ats_support are not supported by CPX-SP FSP.
Remove them from soc_intel_xeon_sp_cpx_config struct.
Remove corresponding settings from DeltaLake devicetree.cb.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ibe1c4e88817fc4be7915e95fa829f0a4c0d947f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Tested=On OCP Delta Lake, BMC SOL can see POST codes
Change-Id: I2c27055475e6dadcd4282cd1bf191a1b83150f02
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
CPX-SP has a CSTACK and 3 PSTACKs. Clean up the HOB header
file to remove reference to non-existing PSTACKs.
Adjust mainboard code accordingly.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ic52b01cd89fb5b3fce64686d91f017f405566acd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
DeltaLake is a single socket server. Its platform design has 1 DIMM
slot per channel. There are 6 DIMM slots.
Configure DIMM_MAX to overwrite SOC default.
Change-Id: I47ecc81452fe59ed59fd3a239ffe329cbc031d7a
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44048
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add driver for OCP specific ipmi commands. With this driver, OCP
specific ipmi command can be used after implementing functions here.
TEST=Build with CB:42242 on Delta Lake, select Kconfig option:
IPMI_OCP and add device in devicetree to open this function.
Use ipmi-util in OpenBMC to dump raw data and check if this
function work.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I2efa85978ec4ad3d75f2bd93b4139ef8059127ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43996
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Execute "dmidecode -t 4" to check if the processor information is correct for Deltalake platform
Change-Id: I5d075bb297f2e71a2545ab6ad82304a825ed7d19
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
According to MP MB to port SMBIOS type8 data.
Tested=Use "dmidecode -t 8" to dump SMBIOS data,
and check if type8 tables are implemented.
Change-Id: I356e645774d78c623c1398c8b1473562e1529cf2
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested on OCP Delta Lake, the timer action can be set correctly.
Change-Id: I1013169e12455e01214d089c9398c78143af4df8
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44019
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VPD variables for enabling/disabling FRB2 watchdog timer and setting
the timer countdown value in romstage. By default it would start the timer
and trigger hard reset when it's expired. The timer is expected to be
stopped later by payload or OS.
Add RO_VPD and RW_VPD sections.
Tested on OCP Tioga Pass.
Change-Id: I53b69c3c5d22c022130fd812ef26097898d913d0
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use the common driver to configure the GPIOs on the Delta Lake
platform as done for Tioga Pass in commit 89d2aa0. The GPIO
settings are dumped by inteltool with original UEFI firmware,
then use intelp2m to generate header file.
TEST=Dump GPIO settings by Intel ITP and check if match gpio.h.
Change-Id: I8005d4caa2d87b6831099bfec3a40246224f3cb5
Signed-off-by: Bryant Ou <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set these fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Icdb6cb39934548e125461929701b33477a74f2a2
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43454
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7a6ddf95d085490d52e00ade7bac23e8c8849427
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42865
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use macros to configure each of the IIO ports instead of an array
of some unknown parameters. This will clean up the code and make
it easier to read.
Tested with BUILD_TIMELESS=1, Tioga Pass, remains identical.
Change-Id: I2911992435a6c93624525426d56212f821abb866
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43502
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When RTC failure is detected, send IPMI OEM command to issue CMOS clear.
This is to let the payload (LinuxBoot) handle the IPMI OEM CMOS
clear command by resetting RTC data, erasing RW_VPD (TODO) and add a
SEL, then reboot the system.
Tested=on OCP Delta Lake, after removing RTC battery we can see the above
flow can be executed correctly.
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Change-Id: I27428c02e99040754e15e07782ec1ad8524def2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43005
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Populate SMBIOS data from OCP_DMI driver read from FRU
2. Set the read PPIN MSR for CPU0 and CPU1 to BMC, selecting
PARALLEL_MP_AP_WORK to enable OCP DMI driver to read remote socket PPIN.
Tested on OCP Tioga Pass.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: Ie11ab68267438ea9c669c809985c0c2d7578280e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40524
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add function to send POST start command to BMC. This function is
used in romstage and the POST end command will be sent in u-root.
TEST=Read POST command log in OpenBMC,
if command received successfully, message may show as below,
root@bmc-oob:~# cat /var/log/messages |grep -i "POST"
2020 Jul 15 16:36:11 bmc-oob. user.info fby3-v2020.23.1:
ipmid: POST Start Event for Payload#2
root@bmc-oob:~#
Signed-off-by: TimChu <Tim.Chu@quantatw.com>
Change-Id: Ide0e2a52876db555ed8b5e919215e85731fd80ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create SMBIOS type 9 by getting PCIe config from BMC.
TEST=Check SMBIOS type 9 is created correctly on different SKUs
Change-Id: Ifd2031b91c960ff2add8807247271eb7c38a0bf2
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change PCH power policy. Set default of
POWER_STATE_DEFAULT_ON_AFTER_FAILURE to n in order to change power
state to S5 when power is reapplied after power failure.
TEST=Base on CB:42289, CB:43338 and build for Deltalake.
The following Kconfig options must be selected:
select SOC_INTEL_COMMON_BLOCK_PMC
select ACPI_INTEL_HARDWARE_SLEEP_VALUES
select CPU_INTEL_COMMON_SMM
Boot the system and check the last bit of GEN_PMCON_B is set to 1
through ITP with command: pch.pm_dump
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I4d4f14bdfc18740976171fd5d369b2d79a916dc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42976
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
are not found
1. Read VPD variable 'fsp_log_level' to decide FSP log level.
2. Define the default values when the VPD variables cannot be found,
put all the values to vpd.h for better documentation and maintenance.
Tested=On OCP DeltaLake, the fsp_log_level can be changed from the VPD variable.
Change-Id: I44cd59ed0c942c31aaf95ed0c8ac78eb7d661123
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts commit a5ca4a0c75237093f1a4d90f30c0c932e5fcd05d.
Reason for revert: Breaks coreboot tree because of non existent kconfig symbol
Change-Id: Ib8f55dc2f6444690945bc2dc64baad5d0c39cdf4
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Implement sending POST start/end command to BMC.
TEST=Read POST command log in OpenBMC,
if command received successfully, message may show as below,
root@bmc-oob:~# cat /var/log/messages |grep -i "POST"
2020 May 28 13:21:22 bmc-oob. user.info fby3-v2020.20.2:
ipmid: POST Start Event for Payload#1
2020 May 28 13:21:25 bmc-oob. user.info fby3-v2020.20.2:
ipmid: POST End Event for Payload#1
root@bmc-oob:~#
Signed-off-by: TimChu <Tim.Chu@quantatw.com>
Change-Id: I38b512ee97c0eda6ba54482a448ef9ffc27b4ddb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41993
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on OCP Delta Lake with lspci checking if PCIe speed is changed
are expected.
Change-Id: I189027c403814d68db2b7c5f41fc254a293fe3a1
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Delta Lake uses GPIO pin GPP_B20 for POST complete event,
BIOS needs to pull this pin low for BIC (Bridge IC) to start
reading sensors.
Tested=On Delta Lake oBMC, bic-util slotx --get_gpio to confirm
the pin is low.
Change-Id: I7e05f8a7caead8ee0632af4ff60ccd8b2412b3dd
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Read VPD variable 'fsp_log_enable' to decide enabling FSP log or not.
With VPD_RW_THEN_RO, VPD_RW takes precedence over VPD_RO, and
would be set to enabled if both places cannot find it.
Tested=On OCP Delta Lake, use vpd to create and set fsp_log_enable
and verified the results are expected.
Change-Id: I0b3463acedd90e8e17f7e4eedc2fab63644f87e1
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: insomniac <insomniac@slackware.it>
|
|
BIC uses LPCflash utility to flash FW, it uses LPC to send the
bridge IC image from host to bridge IC, 0x600 ~ 0x6FF is used
to send BIC image for in-band update support.
TEST=Use LPCflash utility to flash BIC FW on YV3 successfully.
[root@localhost lpcflash_101_bin]# ./lpc_update.sh Y3BRDL_D06.bin
Update Bridge IC Firmware from LPC
Deltalake linux utility ver:1.01
build time: Feb 11 2020 14:30:55
Processing image file: Y3BRDL_D06.bin
.. of size 206968 (0x00032878) bytes
.. file will be padded to a 64-byte size
.. with DEBUG Enabled
Generating CRC-32 for file.
Done (0x4e3905a3).
iBytesRead (0x00007c00).
Discovering LPC boot loader.
Discovered @ 0x3f8.
Configuring LPC boot loader.
Configured @ 0x00000600.
Sending header block.
Sent.
Loading firmware into target.
Sending 31744 bytes ...............................
Sending 31744 bytes ...............................
Sending 31744 bytes ...............................
Sending 31744 bytes ...............................
Sending 31744 bytes ...............................
Sending 31744 bytes ...............................
Sending 16512 bytes .................
Load complete.
Update done!
Signed-off-by: Bryant Ou <Bryant.Ou.Q@gmail.com>
Change-Id: Ia1ea9b35b154225fdfd8955830e6c42b453a81ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
romstage
Add VPD variables for enabling/disabling FRB2 watchdog timer and setting
the timer countdown value. By default it would start the timer and
trigger hard reset when it's expired. The timer is expected to be
stopped later by payload or OS.
Tested on OCP Delta Lake.
Change-Id: I3ce3bdc24a41d27eb1877655b3148ba02f7f5497
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
In romstage get the config from BMC IPMI and update the IIO accordingly.
Tested on OCP Delta Lake with FSP WW24 release, with lspci checking bifurcation
register values are expected.
Change-Id: I412336c32d093fe2bbdc7175f8e596923c77876f
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
CPX-SP FSP ww26 release added UPDs to allow FSP serial redirection. Also
update memory map HOB definition file accordingly.
The CPX-SP soc code is updated to direct FSP log to SOL.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ifd86fb710a0b2bdc8a43225b50b24f585d320caf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42840
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on OCP Delta Lake.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I1e6e2bd25cbe3b0c0547dda9e457c4d55df28388
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42428
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are 4 slots in YV3, Location In Chassis should be 1~4.
Tested=on OCP Delta Lake, dmidecode -t 2 verified the string is correct.
Change-Id: I3b65ecc6f6421d85d1cb890c522be4787362a01b
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
1. Populate SMBIOS data from OCP_DMI driver read from FRU and PPIN MSR
for OEM string 1 to 6, add string 8 for PCIE configuration.
2. Set the read PPIN MSR to BMC.
Tested on OCP Delta Lake.
Change-Id: I9127cf5da1c56d8012694d070615aec24cc22fdf
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41279
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sonora Pass server program was terminated.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I5354ea1e912fd25f0ac9851edf0461413ad8bb21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42948
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bring all GNVS related initialisation function to global
scope to force identical signatures. Followup work is
likely to remove some as duplicates.
Change-Id: Id4299c41d79c228f3d35bc7cb9bf427ce1e82ba1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42489
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Config the IO port for IPMI KCS and set bmc_boot_timeout for checking BMC self test result.
TEST=Check if the BMC IPMI reponse data is correct or not.
Change-Id: I675060299b486986ebc39d8f714615b3e13de89a
Signed-off-by: Morgan Jang <Morgan_Jang@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41023
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add RW_MRC_CACHE flash region to hold MRC cache data.
With memory training skipped for subsequent reboots, the boot
time is reduced by 8 minutes on OCP Delta Lake server, when
FSP verbose logging is turned on.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I27ed00100e1ea9e29b0e71ea5a8397cd550e193a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42025
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
OCP Delta Lake server is a one socket server platform powered by
Intel Cooper Lake Scalable Processor.
The Delta Lake server is a blade of OCP Yosemite V3 multi-host
sled.
TESTED=Successfully booted on both YV3 config A Delta Lake server
and config C Delta Lake server. The coreboot payload is Linux kernel
plus u-root as initramfs. Below are the logs of ssh'ing into a
config C deltalake server:
jonzhang@devvm2573:~$ ssh yv3-cth
root@ip's password:
Last login: Mon Apr 20 21:56:51 2020 from
[root@dhcp-100-96-192-156 ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 52
On-line CPU(s) list: 0-51
...
[root@dhcp-100-96-192-156 ~]# cbmem
34 entries total:
0:1st timestamp 28,621,996
40:device configuration 178,835,602 (150,213,605)
...
Total Time: 135,276,123,874,479,544
[root@dhcp-100-96-192-156 ~]# cat /proc/cmdline
root=UUID=f0fc52f2-e8b8-40f8-ac42-84c9f838394c ro crashkernel=auto selinux=0 console=ttyS1,57600n1 LANG=en_US.UTF-8 earlyprintk=serial,ttyS0,57600 earlyprintk=uart8250,io,0x2f8,57600n1 console=ttyS0,57600n1 loglevel=7 systemd.log_level=debug
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Change-Id: I0a5234d483e4ddea1cd37643b41f6aba65729c8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Kconfig 4.17 started using the $(..) syntax for environment variable
expansion while we want to keep expansion to the build system.
Older Kconfig versions (like ours) simply drop the escapes, not
changing the behavior.
While we could let Kconfig expand some of the variables, that only
splits the handling in two places, making debugging harder and
potentially messing with reproducible builds (e.g. when paths end up
in configs), so escape them all.
Change-Id: Ibc4087fdd76089352bd8dd0edb1351ec79ea4faa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
The prefix mainboard_ was used everywhere else.
Change-Id: Ie576fd47301aa484cb1396e0c6f7260b7698af4d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I13ed3b6e8608c37c1ebe51838e4052f89a638d83
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41947
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I64d9468682a4aae3084b17b8724d035f17d01dff
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This replaces GPLv2-or-later and GPLv2-only long form text with the
short SPDX identifiers.
Commands used:
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
That makes it easier to identify "license only" headers (because they
are now license only)
Script line used for that:
perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist...
Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
It is necessary to rename the file gpio.h so that there are no conflict
with another file (src/include/gpio.h)
Change-Id: I4e3ef5882d6cb0ddbcb8357b54106ff2f47e4c51
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40733
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8599dca99c1f34e3937c5b77b3505815ce625b46
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
If the current pad configuration can not be defined using standard
macros from the gpio_defs.h [1], then the intelp2m utility generates
"advanced" _PAD_CFG_STRUCT() macros. However, often this configuration
in the vendor’s firmware is erroneous. Change the extended macros to
standard ones taking into account the information based on the schematic
diagram and the previous GPIO configuration for FSP-M [2].
[1] src/soc/intel/common/block/include/intelblocks/gpio_defs.h
[2] src/mainboard/ocp/tiogapass/skxsp_tp_gpio.h
Change-Id: I56e45b1df77acbdd67e6325c3745a7ad137f8805
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1
registers values from the inteltool dump, is more understandable and
makes the code much cleaner. The gpio.h file with PAD_CFG macros was
automatically generated using the util/intelp2m [1] utility:
./intelp2m -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
According to the documentation [2], the Host Software Pad Ownership
register only affects the pads that are configured as input (GPI).
The intelp2m utility takes this into account when converting macros
and ignores bits from this register for the corresponding pads.
[1] https://review.coreboot.org/c/coreboot/+/35643
[2] Intel Document Number: 549921
Change-Id: I21e98721e58b00be9196927837daa2b5d2560822
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40731
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to changes in the soc/xeon_sp code [1,2], server motherboards
with Lewisburg PCH can use the soc/intel/common/gpio driver to configure
GPIO controller. This patch adds pads configuration map, which has the
format required by the GPIO driver. The data for this was taken from the
inteltool register dump with AMI firmware. The gpio.h file with pad
configuration was generated automatically using the util/intelp2m [3]:
./intelp2m -raw -p lbg -file tiogapass/vendorbios/inteltool_gpio.log
[1] https: //review.coreboot.org/c/coreboot/+/39425
[2] https: //review.coreboot.org/c/coreboot/+/39428
[3] https: //review.coreboot.org/c/coreboot/+/35643
Change-Id: I818d040fa33f3e7b94b73c9bbbafca5df424616d
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39427
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since CPX FSP headers are not released yet, populate certain
settings with hard-coded offsets. Provided values are probably
not correct and I do not understand what they mean and there is
no documentation available yet. However they were found to work
to a certain degree.
TEST=tested on OCP Sonora Pass EVT
Change-Id: I0f78cde69cb8a49a388a412b97bf8713e5b380ea
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40554
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Just a minimal set of board files needed to get it to boot
in 1 CPU mode.
Signed-off-by: Ryback Hung <ryback.hung%quantatw.com@gtempaccount.com>
Change-Id: Ia7b45c78b38d091bd9535899b681746e13efb4fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
Update UPD IIO bifurcation at run-time according to different Riser
cards. For detail please reference
Facebook Server Intel Motherboard v4.0, Sec. 10.1.2 Riser card types.
With the engineering build FSP, it can only configure IIO for
one socket so my local test needs to remove all socket1 elements
from tp_iio_bifur_table.
This change relies on [1] and need to add GPP_C15 and GPP_C16 to
early_gpio_table for gpio configuration in bootblock.
[1] https://review.coreboot.org/c/coreboot/+/39427/
Tested=OCP Tioga Pass can see socket0 IIO being updated with
an engineering build FSP.
Change-Id: I8e63a233a2235cd45b14b20542e6efab3de17899
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Enable aspeed's function that port 80h direct to GPIO for LED display,
refer to section 9.4 Port 80h Direct to GPIO Guide of aspeed's
Application Design Guide, also configure GPIO to UART for output
serial console messages.
Tested=Check if port 80h LED debug card can display POST codes at
early stage, and serial console can see the related messages.
Change-Id: I087d5a81b881533b4550c193e4e9720a134fb8e7
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40481
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tioga Pass platform use GPIO pin of GPP_B20 for POST complete,
BIOS needs to configure this pin for BMC to poll,
so it knows when to start to access other components.
Tested=Read GPIO status (GPIOAA7) in OpenBMC, the value is 0,
the command and result are shown as below,
root@bmc-oob:~# cat /tmp/gpionames/FM_BIOS_POST_CMPLT_N/value
0
root@bmc-oob:~#
Change-Id: I134f80153461c5acd872587038a2207586b658dd
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I8930e96e5f2c45b8658dc4dfe1ab57d573e7b26f
Fixes: b75bcc978a ("mb/ocp/tiogapass: Properly configure early serial output")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I136e19fbba22b71676a0163a88ae341356c31271
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40088
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tioga Pass comes with AST2500 BMC which offers SuperIO functionality.
However we currently do not configure/enable SuperIO chip. As a result
system boots pretty silently on cold boot. Then FSP configures SuperIO
and resets the system so on next boot serial console does work. This
makes debugging difficult because pre-FSP output is invisible.
This patch enables bootblock to properly configure desired BMC SuperIO
port so early serial output is visible.
TEST=do a cold boot on OCP Tioga Pass, observe bootblock output starting
from bootblock.
Change-Id: Iff8e6a862858d733f529bb9b8c65e22e5ec6b521
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Refactor the code and split it into Xeon common and CPU-specific code.
Move most Skylake-SP code into skx/ and keep common code in the current
folder.
This is a preparation for future work that will enable next
generation server CPU.
TEST=Tested on OCP Tioga Pass. There does not seem to be degradation
of stability as far as I could tell.
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I448e6cfd6a85efb83d132ad26565557fe55a265a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39601
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I426518e8e18de1c8efcfb7ecb0835df3e257dca1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39608
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If we don't pretend to have binaries, there is no need to add fake ones.
This also fixes building the default config.
Change-Id: I8f933f24a734a9ce3d82ef57f7f234ee4dfa86e9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39383
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
OCP platform Tiogapass is a 2-socket server platform, which
is based on a chipset including Intel Skylake-SP processors
and a Lewisburg PCH. Skylake-SP is a processor in Intel Xeon
Scalable Processor family.
Following ACPI tables are added:
DSDT/SSDT, MADT, FACP, FACS, HPET, MCFG, SLIT, SRAT, DMAR
This patchset is tested on a Tiogapass board. It booted with
Linux kernel 4.16.0; lscpu command shows all 72 cpus (2 sockets,
18 cores, 2 thread per core); ssh command shows
networking is up from Mellanox ConnectX-4 PCIe NIC card.
Towards successful gerrit buildbot build, note that:
* microcode is in coreboot intel-microcode submodule repo.
* IFD binary is included in this patch.
* Dummy ME binary is used, as it may take long time for Intel
ME binary to be available in public domain.
* Fake FSP binary is used, as at this moment the SKX-SP
FSP binary is not going to be available in public domain.
Known issues (Not intend to address in this initial support for
Xeon-SP processors):
* c6 state is not supported.
* dsdt table is not fully populated, such as processor/socket
devices, some PCIe devices.
* SMM handlers are not added.
Following are some command execution with CentOS booted from
local SATA disk:
[root@localhost ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 72
On-line CPU(s) list: 0-71
Thread(s) per core: 2
Core(s) per socket: 18
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6139 CPU @ 2.30GHz
Stepping: 4
CPU MHz: 140.415
BogoMIPS: 4626.46
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-17,36-53
NUMA node1 CPU(s): 18-35,54-71
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.23.68.190 netmask 255.255.0.0 broadcast 172.23.255.255
inet6 2620:10d:c082:9063:268a:7ff:fe57:5af0 prefixlen 64 //cut
inet6 fe80::268a:7ff:fe57:5af0 prefixlen 64 scopeid 0x20<link>
inet6 2620:10d:c082:9063::5d2 prefixlen 128 scopeid 0x0<global>
ether 24:8a:07:57:5a:f0 txqueuelen 1000 (Ethernet)
RX packets 84249 bytes 6371591 (6.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8418 bytes 748781 (731.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 613 bytes 63906 (62.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 613 bytes 63906 (62.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@localhost ~]# cbmem
36 entries total:
// Lines were cut to avoid checkpatch.pl warnings
Total Time: 96,243,882,140,175,829
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I29868f03037d1887b90dfb19d15aee83c456edce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Relocatable ramstage, postcar stage and C_ENVIRONMENT_BOOTBLOCK are
now mandatory features, which this platform lacks.
Change-Id: I3d9b6bb48bfd15c0182448f774e9af1e0c944fd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add VPD variables for enabling/disabling FRB2 watchdog timer and
setting the timer countdown value. By default it would start the
timer and trigger hard reset when it's expired. The timer is
expected to be stopped later by payload or OS.
Right now the timer is started after FSP-M. Ideally it should be
before FSP-M (to detect memory training error).
Tested on OCP Mono Lake.
Change-Id: I82b244d08380a0461c92662e025d8b95b3133e23
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add a GPIO table for Monolake to initialize GPIOs with custom board
configurations.
Tested on Monolake.
Change-Id: I74906bf9395a333be6250ffbd181da536e016f30
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Disable root port IOU0 to which built-in NIC is attached.
TEST=on OCP monolake, hide built-in NIC and make sure OS does not report
built-in NIC
Change-Id: I2384e7dd073355f0ced2902ac2d8418996b1c5aa
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Change-Id: I28a21d64e2781af294670a94c1fc88fb81e80f9e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35492
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement Locator and Bank fields (as reported by dmidecode) to match
vendor BIOS.
TEST=on OCP monolake, run dmidecode tool and see that "Locator" field
matches expectation.
Change-Id: Ia271ff1e596ba469cf42e23d8390401c27670a27
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
