| Age | Commit message (Collapse) | Author |
|---|
|
The ME hangs, the lspci shows no memory and the linux kernel
tries to request irq 0 twice. After suspend-resume the linux
kernel warns about double used irq.
genirq: Flags mismatch irq 0. 00000080 (mei_me) vs. 00015a00 (timer)
mei_me 0000:00:16.0: request_threaded_irq failed: irq = 0.
dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -16
PM: Device 0000:00:16.0 failed to resume async: error -16
Change-Id: I56ef66388e58dddcfb858294ba274621c55fbef6
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14309
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Also, fix up the following driver subdirectories by switching
to the src/drivers/[X]/[Y]/ scheme as these are hard requirements
for the main change:
* drivers/intel
* drivers/pc80
* drivers/dec
Change-Id: I455d3089a317181d5b99bf658df759ec728a5f6b
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14047
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is based on t420s. Tested on a T420 without discrete GPU.
There is no support for nvidia gpu and optimus.
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: Iru Cai <mytbk920423@gmail.com>
Change-Id: Ie9405966e56180ac1c43a3c5b83181ee500177c8
Reviewed-on: https://review.coreboot.org/11765
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
power_on_after_fail=Enable in cmos.default leads to wake on AC behaviour
on mobile systems. Therefore set cmos.default entry to "Disable" in order
to improve user experience.
Change-Id: I977a4e6bc028c8c4c7fc1c2f5fdd74a59e951c60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/13884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Set MMCONF_BASE_ADDRESS to 0xf8000000.
It was already done for some boards, but not all.
The sandybridge chipset code assumes 64 pci buses behind MMCONF.
Therefore, only 64MiB of physical address space is required.
Increasing the address allows to use additional 128MiB of MMIO
space and to use the Intel IGD and a PEG at the same time.
Previously it wasn't possible to use both at the same time,
as two 256MiB areas won't fit into MMIO space.
Test system:
* Gigabyte GA-B75M-D3H
* Intel Pentium CPU G2130
* Onboard GPU Intel IvyBridge Desktop
* PEG GPU AMD RV770
Change-Id: I3bf72439056c8089ada6899bb0605e5cd9d89cd6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14096
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
Fix for the T4xx and T5xx series.
It does not apply to X2xx/X6x series as those have only
one GPU, which is always connected to the display.
The T6x series needs special care not handled with this patch.
Without ONBOARD_VGA_IS_PRIMARY the onboard GPU would be
deactivated in case a dedicated GPU is found and active,
leaving the system without a working display.
Change-Id: I94d1700e9afb75de83a4f2ed1ff53ba3b0559ae1
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14031
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Sandy and Ivy Bridge processors use the same socket, and a mainboard
with the socket can support both types of CPUs. However, they use
different native graphics init code for LVDS and cause a crash if
running the wrong code.
This change detects the CPU type and then selects the right code to
run. It will add some more code in ramstage. It also merges the
{SANDY,IVY}BRIDGE_LVDS symbol to one SANDYBRIDGE_IVYBRIDGE_LVDS.
Tested on a Lenovo T520 with i7-2630qm and i7-3720qm
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Change-Id: I4624759f9c92d56d547db1ab4b9a1d611a182a91
Reviewed-on: https://review.coreboot.org/12087
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Use shared gpio code from common folder.
Bd82x6x's gpio.c and gpio.h is used by other southbridges
as well and will be removed once it is unused.
Change-Id: I8bd981c4696c174152cf41caefa6c083650d283a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/13614
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Tested by making lenovo x230 configurable despite pretty MRC bugs.
Change-Id: Ia2a123f24334f5cd5f42473b7ce7f3d77c0e65b7
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13658
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I11e09804ed1d8a7ae8b8d4502bd18f6be933f9fa
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13656
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In the same time remove few native gfx options which were improperly set
and only added dead code to the binary.
Change-Id: I4ed3fec03a1655ae0a779c3aa3845de273cb12e1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13649
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
This is needed for stout EC init.
Change-Id: I5c73499c17763229840152a473a2d820802ee2f6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13535
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I0a0c925509027f98f724d0a4347146f21ac06c02
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13624
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The ThinkPad X220i is essentially identical to the ThinkPad X220 but it
has a Sandybridge i3 (instead of a Sandybridge i5/i7) CPU and the
VGA_BIOS_ID differs. Thus, support is added by using the X220 mainboard
directory and setting the VGA_BIOS_ID in Kconfig.
Change-Id: I33345a099c617e8c87a1de64b7254b7e7716ca90
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-on: https://review.coreboot.org/13594
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
All southbridge interrupt pin and routing registers (D*IP and D*IR)
are left at their default values (see ICH9 datasheet) and this file
just has to reflect them.
Change-Id: I1e9732e178bb8422b284d80d9f3d34b72f2e2415
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/13040
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Values are taken from the vendor BIOS of my X200s. Notable effect:
Stops display from flashing during native graphics init / Linux mode
setting.
Change-Id: Ie5d9efc010a78dd46317b6bbdb7bfacc2c9d2cbf
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12886
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The century byte is used by most RTC (default 0x32@nvram).
Even the century byte can disabled via ACPI it's more safe to reserve
it's space. Because some RTC will act with that byte anyhow.
Some OS overwrite it when syncronize the RTC.
Change-Id: I078c0c57215ccb925afa85b9d067f15268801ec9
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/11853
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Since only X220 with i7 have the USB3 controller this was
probably overlooked.
Before this patch lspci on Linux would not show the NEC USB 3 controller
as well as the PCI bridge it is behind. After, both the bridge and the
NEC controller can be found in the output:
05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller
(rev 04)
Change-Id: I5e7e3f0c7d023f6206a7bec42a39f8955a3d9331
Signed-off-by: Marian Tietz <mtcoreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/12882
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
All southbridge interrupt pin and routing registers (D*IP and D*IR)
are left at their default values (see ICH9 datasheet) and this file
just has to reflect them.
Change-Id: I687262556d918311757fda9afda9ebfdd7edf947
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/12813
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
According to the ACPI Spec for CondRefOf, the result argument is
optional. In all of these locations, it was getting set but not
used, creating a warning in new versions of IASL. Since it's
an optional argument, just remove it.
dsdt.aml 22: if(CondRefOf(\_OSI,Local1))
Warning 3144 - ^
Method Local is set but never used (Local1)
Change-Id: I07f49ac5a3708838d1c4a7216dfb11acc415c881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12692
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The existing code for the Lenovo T400 works without changes on the
Lenovo T500. Same HDA verbs are provided by Lenovo BIOS on both
laptops.
Change-Id: I300408a8a0ed00476aee6061925befc2822fb505
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: https://review.coreboot.org/10545
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
If any path in a method returns a value, IASL expects that all paths
within that method will return a value.
Presumably, the ATPX would not need a return value if Arg0 is anything
other than 0, so just return a zero.
- Serialize ATPX method to make IASL happy. This means that it can
only be used by one thread at a time.
Fixes these issues:
dsdt.aml 2581: Method (ATPX, 2, NotSerialized) {
Remark 2120 - ^ Control Method should be made Serialized
(due to creation of named objects within)
dsdt.aml 2581: Method (ATPX, 2, NotSerialized) {
Warning 3115 - ^ Not all control paths return a value (ATPX)
Change-Id: I14aeab0cebe4596e06a17cffc36cc01b953d7191
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12518
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If any path in a method returns a value, IASL expects that all paths
within that method will return a value.
Presumably the MKHP method wouldn't get called unless there were a
pending event, but if no event is found, return a zero.
Fixes IASL warning:
dsdt.aml 1785: Method (MHKP, 0, NotSerialized)
Warning 3115 - ^ Not all control paths return a value (MHKP)
This was the only IASL warning in most lenovo mainboards.
Change-Id: Id93dcc4a74bd4c18b78f1dde821e7ba0f3444da3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12517
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've actually got more warnings now than when I first tested IASL
warnings as errors. Because of this, I'm adding it with the option
to have it disabled, in hopes that things won't get any worse as we
work on fixing the IASL warnings that are currently in the codebase.
- Enable IASL warnings as errors
- Disable warnings as errors in mainboards that currently have warnings.
- Print a really obnoxious message on those platforms when they build.
***** WARNING: IASL warnings as errors is disabled! *****
***** Please fix the ASL for this platform. *****
Change-Id: If0da0ac709bd8c0e8e2dbd3a498fe6ecb5500a81
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The existing code for the Lenovo T400 works without changes on the
Lenovo R400. Same HDA verbs are provided by Lenovo BIOS on both
laptops.
Change-Id: I1dadddd7250ab80a4c40c2435865d72e3e5d99c9
Signed-off-by: Michał Masłowski <mtjm@mtjm.eu>
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: http://review.coreboot.org/8393
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TEST: Booted T400 with Intel/ATI hybrid graphics in integrated
mode with native Intel graphics init and verified integrated
panel framebuffer functionality in SeaBIOS and Linux.
Change-Id: I37e72c5dad0d7ab3915cc3d439ae9a4a9b3787e3
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9319
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic3cdfa6086a45aa231aa817d5ef6998823589818
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7108
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I0f3297dff47dfb44da034ac6f305dcf1981b9de1
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/11080
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: Ide50b34184b80c86b996f86dd589c3cf3bf75587
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11883
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The ASL code is already present in
`southbridge/intel/common/acpi/platform.asl` and
`cpu/intel/common/acpi/cpu.asl`.
So include these files instead of duplicating the code.
Something similar was don in commit commit 24813c14 (i945: Consolidate
acpi/platform.asl).
Change-Id: I1e69cf0fd73e70ed6656b9ed6f55aba4c56a6edd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11882
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Those are actually board specific. Keep the old value as defaults,
though. The defaults are included by all affected boards.
Change-Id: Ib865c7b4274f2ea3181a89fc52701b740f9bab7d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/11705
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Tested on T60 with intel graphics.
Change-Id: Id74d0a1315749052e7313135242e6b64862aa5e1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5345
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Only one value would work with corresponding gma code currently (which one
depends on board). Going forward, it's possible to compute which number can
be used, so there is no need to keep this info around.
Change-Id: Iadc77ef94b02f892860e3ae8d70a0a792758565d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/11862
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Based on the info by Felix Held.
Change-Id: Iab84dd8a0e3c942da20a6e21db5510e4ad16cadd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/11857
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is a sad story. We have three different code paths for
sandybridge and ivybridge: proper native path, google MRC path, and,
everyone's favorite: Intel FSP path. For the purpose of this patch,
the FSP path lives in its own little world, and doesn't concern us.
Since MRC was first, when native files and variables were added, they
were suffixed with "_native" to separate them from the existing code.
This can cause confusion, as the suffix might make the native files
seem parasitical.
This has been bothering me for many months. MRC should be the
parasitical path, especially since we fully support native init, and
it works more reliably, on a wider range of hardware. There have been
a few board ports that never made it to coreboot.org because MRC would
hang.
gigabyte/ga-b75m-d3h is a prime example: it did not work with MRC, so
the effort was abandoned at first. Once the native path became
available, the effort was restarted and the board is now supported.
In honor of the hackers and pioneers who made the native code
possible, rename things so that their effort is the first class
citizen.
Change-Id: Ic86cee5e00bf7f598716d3d15d1ea81ca673932f
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/11788
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
|
|
While the romstage code flow is not consistent across all
mainboards/chipsets there is only one way of running ramstage
from romstage -- run_ramstage(). Move the
timestamp_add_now(TS_END_ROMSTAGE) to be within run_ramstage().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados. TS_END_ROMSTAGE still present in
timestamp table.
Change-Id: I4b584e274ce2107e83ca6425491fdc71a138e82c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11700
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add the System Board Hardware ID to fix the warning:
dsdt.aml 88: Device (MB) {
Warning 3141 - ^ Missing dependency
(Device object requires a _HID or _ADR in same scope)
Change-Id: Ie97b1e6792c8d4c8db2500cef6a79881b7ff94c8
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10669
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Follow up for commit b890a12, some contributions brought
back a number of FSF addresses, so get rid of them again.
Change-Id: Icf83d5e2a3daea385af3572e9eac6b2431652c28
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10640
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The default route does work for all Chromebooks and is replaced
with platform-specific one in follow-up.
Change-Id: Ia1839ed38dacf44a89dc757394d054e17666f193
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10442
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
At present, no option exists for "Keep VESA framebuffer", which
means that text-mode will be used. Add the appropriate Kconfig
option.
Change-Id: Iaed07eba6d9288c857f7e7a0b0be1107071e49e5
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: http://review.coreboot.org/10553
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
|
|
On i945 legacy brightness control is enabled by a single
bit in BLC_PWM_CTL. It's bit 16 or bit 0 (the other one
reverses polarity). Set the bit to enable brightness
controls.
Change-Id: Id855c4e91fe71fb489739e62fbe99ca22841acd2
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: http://review.coreboot.org/7048
Reviewed-by: Martin Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The same values are used on my Lenovo R400 as reported by Francis Rowe
from his T400 and T500.
TEST: Read /proc/asound/card0/codec#0, see that the jack locations
correspond to the board layout, e.g. headphone and microphone
connectors are on front of the laptop, not right. Read
/sys/class/sound/hwC0D0/init_pin_configs, see that it has the same
content as with factory firmware.
Change-Id: I60e914ca9fab4bb2c99b4ed9e6d81a0580a88b18
Signed-off-by: Michał Masłowski <mtjm@mtjm.eu>
Reviewed-on: http://review.coreboot.org/10431
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I9b86ebec59ccb63db0e1ba61533d162507a22379
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9320
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Change-Id: I8e8b6e7c123e641749c42a7c706176e285902bb5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10502
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic3503938b996bbf31f1417923f019a7bc722b9fd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/10429
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: If2d48b84fe7bd7b144e96171e54067891e3c4e2e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9316
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I8e78cbae132566b6ca27e0a68af2656364c82b8f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9332
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I7fca8c3fa15c1be672e50e4422d7ac8e4aaa1e36
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9598
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Every Lenovo Thinkpad includes a Trusted Platform Module, so we can enable
it for the sandy-/ivybridge platforms.
Change-Id: Icda443ba88c2a49a0033014ce7710dd607fa15dc
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: http://review.coreboot.org/10411
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I6416cd5780fbda0b3c2e236ce98a9f9a508e70c6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10293
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Remove dead code and dead includes.
Change-Id: I5564ebfbbef6f65c275c2f94f75724f4e36472db
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10349
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
PS/2 emulation is part of H8, so should be inited in relevant files.
Change-Id: Ie873ea7f6f88f68f622351799462d0b000d17585
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10348
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Previously only internal mic really worked but since it's of good quality
it's not really noticeable.
Change-Id: Ie14c377b0370302d97e1f89eae5787e05e73b7d2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10286
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Not used anywhere.
Change-Id: I9bab092d285aaebdf9283ba08e23197f9785b3a6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10329
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Old igd.asl had inconsistent addresses (between _DOD and actual device)
and ghost devices. Any of those is enough to make brightness on windows
fail and make igd.asl out-of-ACPI-spec. Also old code favoured ridiculous
copying of the same thing 6 times per chipset. Leave only hooking up and
chipset-specific part in chipset directory. Move NVS handling and ACPI-spec
parts to a common file.
Change-Id: I556769e5e28b83e7465e3db689e26c8c0ab44757
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7472
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
This allows to deactivate TPM on X201.
Change-Id: Ic085db6cc2c57668e7a4fdbc7440735c806cc256
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10278
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
|
|
This allows to deactivate TPM on X230.
Change-Id: I73d4272da62335ec3766ce4814d5b46538b190fe
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10273
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
|
|
The comment about necessity of include isn't true anymore as get_cst_entries
is not weak anymore so if it's not found, the linking would fail.
Change-Id: I4bf88208d63ac3e625f464c3907e2e1ea575dd9f
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7375
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
This code in reality just describes the southbridge features, don't put a copy
in every mainboard.
Change-Id: I8cf3019a36b1ae6a17d502e7508f36ea9fa62830
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10231
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: build bot (Jenkins)
|
|
Same comments were already removed for the latest board, the amd/lamar.
Change-Id: Ie244f838409c567c11f7444c9cf17de72e49dbb0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10283
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Implementation corrupts low-memory on S3 resume path, rendering
OS unstable. AMD was never able to pinpoint a revision that did
not have the issue.
Change-Id: I9656ac1bfe1412775a6152b9f995c4d4ebf57159
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10285
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Tested-by: build bot (Jenkins)
|
|
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Change-Id: I8df5b7f6707957b925f7bb4dc06a717252c70868
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10275
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: build bot (Jenkins)
|
|
acpi_fill_slit and acpi_fill_srat were removed in commit 5e597572e.
Take care of the boards that were added in the mean time.
Change-Id: I907e51de5d4ce9acfcce82e6bb30eefff312d35d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
SLIT and SRAT are created this way only on amdk8 and amdfam10.
This saves the need of having a lot of dummies.
Change-Id: I76d042702209cd6d11ee78ac22cf9fe9d30d0ca5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7052
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I9c938b8a69479fae6b0eb99d1135f1caaf26d0e2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10227
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Sample code belongs to documentation, not copied 100x over prodcution code.
Change-Id: I6bb318d76057d02bd6ac5641d12d56ab6d60b745
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10229
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3047badea8d4f61155f4e4f7d3d078426948162a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10228
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Just a copypaste, never worked.
Change-Id: I84b46a5a0ada2e472894c63a17170e0979ad9160
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10218
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This patch is based on commit f2b3cd63
(lenovo/x60: Support digitizer on X60t and X201t)
Tested on Thinkpad X200 Tablet (7450): all pen functionallity
works (i.e. movements, presure sensitivity and buttons)
Change-Id: I9bd18642a6ea4211dc3be065456a507fc0b72561
Signed-off-by: Alex David <opdecirkel@gmail.com>
Reviewed-on: http://review.coreboot.org/10208
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Change-Id: Ia5e26110928fa011305c13362f20fbe78ca9cf30
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7134
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Without this some radios may remain operational. They may consume power but
the immediate demonstrable effect is wireless LED still being on.
Coreboot will reenable radios on resume or poweron.
Change-Id: I9fcb08880964b1594f779a246840bc3013a44afe
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10190
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
x230 is ivy, not sandy. Fix copy-paste error.
Change-Id: Ic462bab39ddac0e1e6fef1e043970957e45fb6ed
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10189
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
These tables are not referenced anywhere, thus all
comments about adjustments are void.
Also drop stub AgesaReadSpd that is all commented out.
Change-Id: I12233ea0dc4baaf36a75f359c52cc59c9b6dad79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10143
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Change-Id: I9f65922d0785e06a173221b3262e73b575087dfd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9321
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move the GPI interrupt routing selection between SMI/SCI from
mainboards to southbridge. There is speculation if this is all
just legacy APM stuff that could be removed with a followup.
Change-Id: Iab14cf347584513793f417febc47f0559e17f5a5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/7967
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
For lenovo/x201, this also changes GPI_ROUT (0xb8-0xbb)
programming to use GPI1 between SCI/SMI modes, while
previous programming was for GPI12.
Change-Id: I3ac0feaa1d10c8f0e53a5fa5af72366503bb5d2d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8656
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
To simplify browsing the "Supported hardware" list, I added Release year
for the hardware from asus, asrock, gigabyte, msi, via, tyan, intel,
lenovo, apple, jetway and hp. Still several models and manufacturers to
add information to. This is more of a proof-of-concept.
The "Release year" will be shown in the wiki page.
Change-Id: I6bc14ed06ac7c6b3c9f054b49f08cb9b3dc47947
Signed-off-by: Mathias Friman <mathias@workplays.se>
Reviewed-on: http://review.coreboot.org/9963
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Tested on T530, T430s.
Verified with lspci dump.
Change-Id: I45acadb0c55534a67f7ad3e7bd84f4482a4344d7
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/9451
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
x201 has 2 sata ports. 1 port for hard drive and 1 port for the dock.
Tested on x201 with hdd in port 1 + cdrom in port 2.
Change-Id: I1ee8c547392257d4f2e00a5d48e21447a84f79c0
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/8657
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
The nehalem smi finalize handler was just copied from sandybridge,
without even changing the function name.
TEST=Built and tested on x201t with additional patch to use finalizers
Change-Id: Ifb44eeaaa6e03556deeb5d12ed1147e02d6d6eb9
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/8292
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Set correct gpio routing and enable bits for EC SMI gpio and EC WAKE gpio.
Verified with schematics.
Change-Id: Ie3b98c4456a870c881e7663b19eb8ca8e5564c5c
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8358
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We do not allow platforms to mess around with memory layout.
Change-Id: I316ff522c8833fa3b7ad20f2c5a9cae21f4174d8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The existing code generated invalid ACPI processor objects
if the core number was greater than 9. The first invalid
object instance was autocorrected by Linux, but subsequent
instances conflicted with each other, leading to a failure
to boot if more than 10 CPU cores were installed.
The modified code will function with up to 99 cores.
Change-Id: I62dc0eb61ae2e2b7f7dcf30e9c7de09cd901a81c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8422
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: I19d6b56e3ac5e6e7946648b97c86a223b748e3bd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8460
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Icebc12d8f83494150a7bdd3adcc168d7b48b2e68
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8458
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iccad79c142a7fcf89dd0fbebe8c07ad9ef019e91
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8459
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
On x86, change the type of the address parameter in
read8()/read16/read32()/write8()/write16()/write32() to be a
pointer, instead of unsigned long.
Change-Id: Ic26dd8a72d82828b69be3c04944710681b7bd330
Signed-off-by: Kevin Paul Herbert <kph@meraki.net>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/7784
Tested-by: build bot (Jenkins)
|
|
The original firmware has a 2 MiB BIOS region in both 4 MiB and 8 MiB
flash variants. Let's allow using the whole region instead of the
gm45 default of 1 MiB.
Change-Id: I2d8a04bcb992bf2e8e15890a5c6719810b1cf405
Signed-off-by: Michał Masłowski <mtjm@mtjm.eu>
Reviewed-on: http://review.coreboot.org/8392
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The port is based on the x230 / t530.
Tested - is in active use.
Change-Id: Ic5ccfe70343e8aef3465690edce9cdebf153a44d
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8359
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Fixes USB3 ports degraded to USB2 speeds.
Change-Id: Ie71c9fb6e52a3e72bb1e61351ad1cc0492d93cbc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/8313
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
same as 37130ebdabe44989787aadeafbe79524970dec75
Change-Id: I73feed3a077dfcc61634147775df1e05fdb97e8b
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8278
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
OC2 at port 4 was missing. Verified with RCBA dump.
Change-Id: Ide5701d53aeee28619204c7ac408662626aa11e4
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8304
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
thinkpad_acpi checks that BIOS version matches some pattern.
Report version in this form.
same as http://review.coreboot.org/4650 /
63acd22dc5366c72a7165138f5030df9523824dc
Change-Id: I82d7a2b9f2ec56557b3a9c26d1af57ed39e31850
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8302
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
