| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib7beed7218f317bc2352b65a6191ef1cdaa0742d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
- Add support for ME Soft Temporary Disable Mode. In this mode, ME
doesn't load its kernel and freezes at Bring UP (BUP) phase. This mode
is saved in ME NVRAM (and thus will remain for next reboots and
poweroffs).
- Add support of new CMOS option for Sandy Bridge and Ivy Bridge
ThinkPads.
HOW TO USE
To disable ME:
1. nvramtool -w me_state=Disabled
2. reboot
To enable it back:
1. nvramtool -w me_state=Normal
2. reboot
To check current status:
intelmetool -m
Tested on ThinkPad X230 and ThinkPad X220.
BACKGROUND
There's no Intel documentation that would explain how this should be
implemented, in public. Working binary sequence for MKHI command to put
ME in Soft Temporary Disable Mode, as well as a way to bring ME out of
it (by writing to H_GS register), was found and published by researchers
from PT Security:
1. To disable ME, BIOS issues the disable command (before End of Post)
and reboots. ME is supposed to be disabled on the next boot after
DID (DRAM Init Done).
My numerous tests show that issuing the command and rebooting is not
enough. If we reboot too early, ME will not be disabled. Apparently,
it is doing something in background after receiving the command. It
works with a delay of 500-1000 ms.
I also tried to dump all known (documented) registers, such as GMES
and HFS, before and during the next 2 seconds after execution of the
disable command to find a possible indication that something's
changed in ME and we're ready to reboot. Found nothing
unfortunately.
2. To enable ME back, host writes value 0x20000000 to H_GS.
PT slides don't contain any more information on it, but my tests
show, that after writing this value, GMES[31:28] is changing from
0x01 (BUP phase) to 0x03 (Policy Module) to 0x06 (Host
Communication). Then, after some more time, fw_init_complete bit of
HFS becomes 1.
This means that ME starts loading its kernel immediately, without
reboot.
On the other hand, Lenovo BIOS clearly perform a reboot after
enabling it (one reboot after saving the settings, then ThinkPad
logo appears, and then one more reboot). I'm assuming we have to
reset too.
Change-Id: Ic01526c9731cbef4e8552bbc352133a2415787c2
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Used default console log level is 7 in src/console/Kconfig.
So let cmos.default use the same level as default.
Change-Id: Ia39ee457a8985142f6e7a674532995b11cb52198
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fix for all Sandy-Bridge and Ivy-Bridge devices.
Remove unused option "hyper_threading".
Increase CMOS checksum range to cover all user adjustable settings.
Change-Id: I02f7af13d9c82d7f531d4b49b3bc0e5a20c14b55
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
USB AO is the internal name for the dedicated charging port on
ThinkPads when in S3 or lower.
AOEN (bit 0) is internal name for enabling this feature while AOCF
(bits 2 and 3) is the configuration field. According to Peter Stuge,
AOCF can be configured in this way:
00 => AC S3 S4 S4 USB on, battery S3 USB on, battery S4 S5 off
11 => AC S3 S4 S4 USB on, battery S3 S4 S5 USB off
10, 01 => equivalent to 00
This commit also adds a new configuration field in the CMOS of the
X220 and the X201 to activate this feature. It probably can be also
added to all the ThinkPads that support this functionality.
With this functionality USB devices are able to negotiate full power
from the dedicated port (usually the yellow one) even in S3.
Tested on a X201 and X220 with an Android smartphone: with this
feature enabled it shows "Charging" when connected during S3, without
it it shows "Charging slowly" (or it doesn't charge at all on the
X201).
For some reasons the "AC only" mode doesn't work, so it has been
disabled.
Change-Id: Ie1269a4357e2fbd608ad8b7b8262275914730f6e
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/17252
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
power_on_after_fail=Enable in cmos.default leads to wake on AC behaviour
on mobile systems. Therefore set cmos.default entry to "Disable" in order
to improve user experience.
Change-Id: I977a4e6bc028c8c4c7fc1c2f5fdd74a59e951c60
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/13884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic213948e4d31457dda9b9f2d5a4f92cd34d1e57d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6757
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
