| Age | Commit message (Collapse) | Author |
|---|
|
This timeout is probably needed on all devices with Lenovo H8 embedded
controllers so set the default there.
Change-Id: I830ab1894f7c0f10f55c82e398becf44d810852d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18274
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
This allows for defaults to be applied to CMOS parameters
when cmos checksum is incorrect.
This probably results in changed cmos settings for current users of
these targets.
Change-Id: Ifec0093f4b0dbaa51b96812a041f0eaf5c58ee86
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17041
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is more consistent with newer Intel targets.
This a static struct so it is initialized to 0 by default.
To make it more readable:
* only setting to GPIO mode is made explicit;
* only pins in GPIO mode are either set to input or output since this
is ignored in native mode;
* only output pins are set high or low, since this is read-only on
input;
* blink is only operational on output pins, non-blink is not set
explicitly;
* invert is only operational on input pins, non-invert is not set
explicitly.
Change-Id: I05f9c52dee78b7120b225982c040e3dcc8ee3e4e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17639
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Having same memory region set as both WRPROT and WRBACK
using MTRRs is undefined behaviour. This could happen if
we allow DCACHE_RAM_BASE to be located within CBFS in SPI
flash memory and XIP romstage is at the same location.
As SPI master by default decodes all of top 16MiB below
4GiB, initial cache-as-ram line fills may have actually
read from SPI flash even in the case DCACHE_RAM_BASE was
below the nominal 4GiB - ROM_SIZE.
There are no reasons to have this as board-specific setting.
Change-Id: I2cce80731ede2e7f78197d9b0c77c7e9957a81b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17806
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I8313ba1d93922297e5061701dad47d07617d1dcd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17804
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of hardcoding pci_mmio_size in the raminit code,
this makes it a parameter in the devicetree.
A safe minimum of 768M is also defined since using anything
less causes problems (if 4G of ram is used).
Change-Id: If004c861464162d5dbbc61836a3a205d1619dfd5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16856
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Don't use scratchpad registers when we have romstage_handoff
to pass S3 resume flag. Scratchpad register was read too
late in ramstage so acpi_is_wakeup_s3() did not evaluate
correctly.
This fixes low memory corruption at 0x1000-0x102c and the lack
of coreboot tables (util/cbmem not working) after S3 resume.
This also fixes console log from reporting early in ramstage
"Normal boot" while on "S3 resume" path.
Change-Id: I2922a15a90d2f8272c3482579bdd96f8f33e9705
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17675
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Regardless of the payload chosen a file etc/ps2-keyboard-spinup
is added to cbfs. With this fix this file is only added to cbfs when
seabios is choses as a payload.
Change-Id: I37cf4c998856db2d297356776752643dba46a8f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16146
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I341293cd334d6d465636db7e81400230d61bc693
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16723
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Replace the use of the old device_t definition inside
mainboard/lenovo/t60.
The patch has been tested both with the arch/io.h definition of device_t
enabled and disabled in order to ensure compatibility while the
transaction takes place.
Change-Id: I4d87498637d74f96ca5809b0e810755a58fc64ab
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/16405
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This creates a config for the Lenovo T60 sound card based
on values taken from vendor bios
(in /sys/class/sound/hwC0D0/init_pin_configs on linux 3.16).
The sound card configuration on the vendor bios is the same
as the one on the Lenovo x60.
It improves the default behavior of the sound card:
- internal microphone is chosen by default
- when jack is inserted it is chosen instead of internal speaker
Change-Id: I44e3eaac437fe4ad97ff2b0eb32d36b33222c09b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16529
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
On i945 the vram size is the default 8mb. It is also possible
to set it 1mb or 0mb hardcoding the GGC register in early_init.c
The intel documentation on i945, "Mobile Intel® 945 Express Chipset
Family datasheet june 2008" only documents those three options.
They are set using 3 bits. The documententation also makes mention
of 4mb, 16mb, 32mb, 48mb, 64mb but not how to set it.
The other non documented (straight forward) bit combinations allow
to change the VRAM size to those other states.
What this patch does is:
- add those undocumented registers with their respective vram size to
the i945 NB code;
- make this a cmos option on targets that have this northbridge.
TEST: build, flash to target, set cmos as desired and boot linux.
On Debian it can be found using "dmesg | grep stolen".
NOTE: dmesg message about reserved vram are quite different depending
on linux version
Change-Id: Ia71367ae3efb51bd64affd728407b8386e74594f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/14819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since commit 3bfd7cc (drivers/pc80: Rework normal / fallback selector
code) the reboot counter stored in `reboot_bits` isn't reset on a reboot
with `boot_option = 1` any more. Hence, with SKIP_MAX_REBOOT_CNT_CLEAR
enabled, later stages (e.g. payload, OS) have to clear the counter too,
when they want to switch to normal boot. So change the bits to (h)ex
instead of (r)eserved.
To clarify their meaning, rename `reboot_bits` to `reboot_counter`. Also
remove all occurences of the obsolete `last_boot` bit that have sneaked
in again since 24391321 (mainboard: Remove last_boot NVRAM option).
Change-Id: Ib3fc38115ce951b75374e0d1347798b23db7243c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16157
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia1f24d328a065a54975adde067df36c5751bff2d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15987
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9bfaa53f8d09962d36df1e86a0edcf100bb08403
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/15229
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I0a0c925509027f98f724d0a4347146f21ac06c02
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/13624
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The century byte is used by most RTC (default 0x32@nvram).
Even the century byte can disabled via ACPI it's more safe to reserve
it's space. Because some RTC will act with that byte anyhow.
Some OS overwrite it when syncronize the RTC.
Change-Id: I078c0c57215ccb925afa85b9d067f15268801ec9
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/11853
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
If any path in a method returns a value, IASL expects that all paths
within that method will return a value.
Presumably the MKHP method wouldn't get called unless there were a
pending event, but if no event is found, return a zero.
Fixes IASL warning:
dsdt.aml 1785: Method (MHKP, 0, NotSerialized)
Warning 3115 - ^ Not all control paths return a value (MHKP)
This was the only IASL warning in most lenovo mainboards.
Change-Id: Id93dcc4a74bd4c18b78f1dde821e7ba0f3444da3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12517
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've actually got more warnings now than when I first tested IASL
warnings as errors. Because of this, I'm adding it with the option
to have it disabled, in hopes that things won't get any worse as we
work on fixing the IASL warnings that are currently in the codebase.
- Enable IASL warnings as errors
- Disable warnings as errors in mainboards that currently have warnings.
- Print a really obnoxious message on those platforms when they build.
***** WARNING: IASL warnings as errors is disabled! *****
***** Please fix the ASL for this platform. *****
Change-Id: If0da0ac709bd8c0e8e2dbd3a498fe6ecb5500a81
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic3cdfa6086a45aa231aa817d5ef6998823589818
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7108
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The last_boot NVRAM option was deprecated and removed in
commit 3bfd7cc6. Remove the last_boot option from all
affected mainboards to eliminate user confusion.
Change-Id: I7e201b9cf21dfe5dda156785bad078524098626d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/12316
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/southbridge/intel/i82801gx/acpi`. Devices with the
southbridge `intel/i82801ix`, like the laptop Lenovo X200, use the exact
same ASL code though. So share this in the directory
`src/southbridge/intel/common/acpi`.
Change-Id: I33b7993bcdbef7233ed85a683b2858ac72c1d642
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Commit 24813c14 (i945: Consolidate acpi/platform.asl) creates the file
in the directory `src/cpu/intel/model_6dx/acpi`, although the devices
can also use different Intel CPU models like, for example,
`intel/model_6ex` on the Lenovo T60.
Therefore move the file to the directory `src/cpu/intel/common/acpi` so
that other devices, like Intel GM45 based devices, can also include it.
Change-Id: I90126b66a4d70468923622a8e3aebadeafcbf96f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/11880
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Tested on T60 with intel graphics.
Change-Id: Id74d0a1315749052e7313135242e6b64862aa5e1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5345
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
While the romstage code flow is not consistent across all
mainboards/chipsets there is only one way of running ramstage
from romstage -- run_ramstage(). Move the
timestamp_add_now(TS_END_ROMSTAGE) to be within run_ramstage().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Built and booted glados. TS_END_ROMSTAGE still present in
timestamp table.
Change-Id: I4b584e274ce2107e83ca6425491fdc71a138e82c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/11700
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Old igd.asl had inconsistent addresses (between _DOD and actual device)
and ghost devices. Any of those is enough to make brightness on windows
fail and make igd.asl out-of-ACPI-spec. Also old code favoured ridiculous
copying of the same thing 6 times per chipset. Leave only hooking up and
chipset-specific part in chipset directory. Move NVS handling and ACPI-spec
parts to a common file.
Change-Id: I556769e5e28b83e7465e3db689e26c8c0ab44757
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7472
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Change-Id: I8df5b7f6707957b925f7bb4dc06a717252c70868
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10275
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Tested-by: build bot (Jenkins)
|
|
SLIT and SRAT are created this way only on amdk8 and amdfam10.
This saves the need of having a lot of dummies.
Change-Id: I76d042702209cd6d11ee78ac22cf9fe9d30d0ca5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7052
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3047badea8d4f61155f4e4f7d3d078426948162a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10228
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Without this some radios may remain operational. They may consume power but
the immediate demonstrable effect is wireless LED still being on.
Coreboot will reenable radios on resume or poweron.
Change-Id: I9fcb08880964b1594f779a246840bc3013a44afe
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10190
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Move the GPI interrupt routing selection between SMI/SCI from
mainboards to southbridge. There is speculation if this is all
just legacy APM stuff that could be removed with a followup.
Change-Id: Iab14cf347584513793f417febc47f0559e17f5a5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/7967
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
For lenovo/x201, this also changes GPI_ROUT (0xb8-0xbb)
programming to use GPI1 between SCI/SMI modes, while
previous programming was for GPI12.
Change-Id: I3ac0feaa1d10c8f0e53a5fa5af72366503bb5d2d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/8656
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
To simplify browsing the "Supported hardware" list, I added Release year
for the hardware from asus, asrock, gigabyte, msi, via, tyan, intel,
lenovo, apple, jetway and hp. Still several models and manufacturers to
add information to. This is more of a proof-of-concept.
The "Release year" will be shown in the wiki page.
Change-Id: I6bc14ed06ac7c6b3c9f054b49f08cb9b3dc47947
Signed-off-by: Mathias Friman <mathias@workplays.se>
Reviewed-on: http://review.coreboot.org/9963
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Iccad79c142a7fcf89dd0fbebe8c07ad9ef019e91
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/8459
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
On x86, change the type of the address parameter in
read8()/read16/read32()/write8()/write16()/write32() to be a
pointer, instead of unsigned long.
Change-Id: Ic26dd8a72d82828b69be3c04944710681b7bd330
Signed-off-by: Kevin Paul Herbert <kph@meraki.net>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/7784
Tested-by: build bot (Jenkins)
|
|
Missing base may have enabled SMI for all GPI inputs.
Change-Id: I1157afaccccb17d325a4efdb1f270a27f9a299ab
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8169
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix system include paths to be consistent. Chipset support is
part of the Coreboot 'system' and hence 'non-local' (i.e., in
the same directory or context). One possible product of this, is
to perhaps allow future work to do pre-compiled headers (PCH) on
the buildbot for faster build times. However, this currently just
makes mainboard's consistent.
Change-Id: I2f3fd8a3d7864926461c960ca619bff635d7dea5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8085
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This brings mainboard up to being consistent tree-wide now for
all superio header path inclusions.
Change-Id: I00a806ce209ba363c62e3ddd49db9bf599f32149
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/8052
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Keep only the last one: it was the one which was really used.
Change-Id: I19132f6224d6847e615e3c582aaa6e66b0d56c7a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7677
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
This config is used only to generate PIRQ table. If no such table is
supplied there is no need for config.
Change-Id: I537d440f53019a6bf7f190446074e75e7420545a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7566
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Iccb2dda8a427e483c04693e46b00e0bc2452a26b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7086
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Otherwise checksum may not work correctly on early stages.
For compatibility with old bootblocks also enable it early in romstage.
Change-Id: Ie541d71bd76af182e445aa5ef21fe5ba77091159
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7556
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
There were instances of unneeded arch/hlt.h includes,
various hlt() calls that weren't supposed to exit (but
might have) and various forms of endless loops around
hlt() calls.
All these are sorted out now: unnecessary includes are
dropped, hlt() is uniformly replaced with halt() (except
in assembly, obviously).
Change-Id: I3d38fed6e8d67a28fdeb17be803d8c4b62d383c5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/7608
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This was copied from P2B-F without doing any modification. It never worked.
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Change-Id: I2c90688c8ff8c3bd272d24f059e8e1bfb86e2b4a
Reviewed-on: http://review.coreboot.org/7555
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
As build.h is an auto-generated file it was necessary to add it as
an explicit prerequisite in the Makefiles. When this was forgotten
abuild would sometimes fail with following error:
fatal error: build.h: No such file or directory
Fix this error by compiling version.c into all stages.
Change-Id: I342f341077cc7496aed279b00baaa957aa2af0db
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/7510
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I00c2c725de5b982a5e4f584b77b09017a5bc0a72
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7062
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Idc3522807b17e56bdaf8f04b4bd68c6ed9777363
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7110
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
Do all the handling in SB code with few parameters from devicetree.cb
instead of having mobo callbacks.
Change-Id: I8fd02ff05553a3c51ea5f6ae66b8f5502509e2bc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7199
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: Ia4060831236d72f880eeff6263ada40cf195fb12
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7180
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I0ace5f49b84170ab4701ad1b70d3c50c99066e53
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7178
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I076cba7d21926cabf90d485de50268ae40c435f3
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7087
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I179a4cede2f826f72a400208748798737216c01a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7071
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Iee3ee33ca58b8c722d2d38aae31e7130032512ad
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6804
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: Ib3e09644c0ee71aacb067adaa85653d151b52078
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6840
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I9366dded98bf15f6da44ce893dd10698ba09fd55
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6820
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I12ce0dda823d7733c473ed5ef3b0470d95d794ae
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6805
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
OEM strings should not be handled by mobo code but by common code with strings
collected from all devices.
Change-Id: Ibde61a1ca79845670bc0df87dc6c67fa868d48a9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6788
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
This header has nothing to do with cache-as-ram. Therefore, 'car'
is the wrong term to use. It is about providing a prototype for
*romstage*.
Change-Id: Ibc5bc6f3c38e74d6337c12f246846853ceae4743
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/6661
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
When passing '-ffreestanding' the 'main' romstage.c may no longer
necessarily be considered the entry point.
From the C specification in 5.1.2.1 Freestanding environment;
"In a freestanding environment (in which C program execution may take
place without any benefit of an operating system), the name and type of
the function called at program startup are implementation-defined."
Clang complains about these being missing as Clang is somewhat more
strict about the spec than GNU/GCC is. An advantage here is that a
different entry-point type-signature shall now be warned about at
compile time.
Change-Id: I467001adabd47958c30c9a15e3248e42ed1151f3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5872
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: If29a70be4fb56ebb0dbf6d510412cbe2f34480ef
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6291
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: Ib531a54db7df6b49a6218f689dcaab712e9dfb01
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6292
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Change-Id: I05d6d22664155ac8478e665733f816776e277c22
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6200
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I1bbcba086f841a90544b827ae807a3c351d19d21
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6036
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
|
|
This code would not get enabled just by flipping the options in menuconfig,
also ramcheck() no longer test the range like the parameters would imply.
We should add non-destructive ram_check() on S3 resume path to verify
memory controller configuration has been properly recovered.
Change-Id: Ie4675c4770146c4312cdfbc81afa19f243f90ee4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6027
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I7811ee695f35c708144c4af5d43935deb22dd4df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6061
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Without it option ROM run results in just a black screen.
Change-Id: Id203f55ca0f02c290a3f40ac1ec7c5f23c5580bf
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5344
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
thinkpad_acpi checks that BIOS version matches some pattern.
Report version in this form.
Not cleaned up as the idea of this patch seems to be met with resistance.
Can make it Thinkpad-specific if the idea is accepted.
Change-Id: I15e33e87e7a7f42d6a06f12fb39b5172153af8a1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4650
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove use of global variables uma_memory_base and uma_memory_size
from builds with Intel northbridges, as these variables can be kept
within the chipset or even as stack locals.
Intel platforms have no functional implemenation for option GFXUMA.
If we did implement some choice between external and integrated graphics,
it needs to be named in less obscure fashion.
Change-Id: I12f18c4ee6bc89e65a561db6c2b514956f3e2d03
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5720
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
When the system is started with dock, the serial port works.
As soon as the laptop is undocked and redocked, the serial port
no longer works. See below superiotool dump snippet:
Upon bootup: SIO @ 0x2e
LDN 0x03 (COM1)
idx 30 60 61 70 71 74 75 f0
val 01 03 f8 04 03 04 04 02
Redocked: SIO @ 0x2e
LDN 0x03 (COM1)
idx 30 60 61 70 71 74 75 f0
val 00 03 f8 04 03 04 04 02
Since the function dock_connect is executed every time the
dock is reconnected, starting without a dock and then attaching
it to a dock is now also fixed.
Change-Id: Ibd97589a8c743673a55e382a5db2ba62656c595e
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/5761
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
linux/drivers/platform/x86/thinkpad_acpi.c looks for an EC
version string before loading, this code copies the vendor BIOS by
exposing this string. This was originally part of x60's mainboard.c
Change-Id: I5e54ea2833252bc4dbba46ceb67d78c435b34845
Signed-off-by: Trevor Mosey <uberushaximus@gmail.com>
Reviewed-on: http://review.coreboot.org/5638
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
mainboard_enable() is now modelled after google/parrot where the
enable function only sets dev->ops->init for the root device to
point to a mainboard_init() function, which in turn is called in a
later pass over the device tree to do the actual initialization.
Change-Id: I89a5192bd45ca8321b2b1ac49b073122e0f6ee2b
Signed-off-by: Trevor Mosey <uberushaximus@gmail.com>
Reviewed-on: http://review.coreboot.org/5637
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
CONFIG_ARCH is a property of the cpu or soc rather than a property of the
board. Hence, move ARCH_* from every single board to respective cpu or soc
Kconfigs. Also update abuild to ignore ARCH_ from mainboards.
Change-Id: I6ec1206de5a20601c32d001a384a47f46e6ce479
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5570
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
$ git grep -l Cnotr | xargs sed -i 's/Cnotr/Contr/g'
Change-Id: Iee826a8092dbf17f8a28b7eb7b6d183464c6e498
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5325
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
EEPROM/RFID chip present in thinkpad should be locked in a way to avoid
any potential RFID access.
Read serial number, UUID and P/N from EEPROM.
This info is stored on AT24RF08 chip acessible through SMBUS.
Change-Id: Ia3e766d90a094f63c8c854cd37e165221ccd8acd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4774
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
The code for handling the invalid CMOS space in mainboard.c
is now useless and so it was removed.
Change-Id: I86ec6a7f73e32948adff9087d4af5372a49a46a5
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3520
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The replacement function confirms CBMEM TOC is wiped clean on power
cycles and resets. It also introduces compatibility interface to ease
up transition to DYNAMIC_CBMEM.
Change-Id: Ic5445c5bff4aff22a43821f3064f2df458b9f250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4668
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
board_info.txt is a file to be used by board-status to add
some useful info to the generated table like flash chip type.
This series is autogenerated from wiki page Supported_Motherboards.
Change-Id: Ie2bda900713ef4883134477163320936c84c34f5
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4701
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
To be consistent with touchpad counterpart.
Change-Id: I72d09b41b964f80a81fbf409ef69dd368834a3e2
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4654
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I6652e0ad4e0179950f775bbd0200484907bfc976
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4653
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
To stay in line with wwan and bluetooth.
Change-Id: Iafe2dc97fc2aec5c2ad1834659b796a6b079c1bc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4652
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I2f422e83f2afcf0cc3f3ecbace01a8f4f39e87d4
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4663
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
They're pretty annoying.
Change-Id: I44d26dc168927a9cedfd6ecc4c9a51a3a7b362c7
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4662
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Useful for accessibility.
Sticky modifier (sticky Fn) is a behaviour of modifier key when
you don't have to hold it pressed to achieve the result. E.g.
with normal Fn brightness up is:
<Press Fn> <Press Home> <Despress Home> <Depress Fn>
With sticky Fn you can do:
<Press Fn> <Depress Fn> <Press Home> <Despress Home>
Change-Id: I4da5adcea02428d936023891de08684cae77c44e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4661
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Tested on my X201 and X230.
Change-Id: I3c7ec65681157d15c6e87eea64779a08e03ae5a8
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4660
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
wwan_enable was never used.
wlan_enable isn't something for device tree but for CMOS config if at all.
Change-Id: I765d9d6f0b73b7dc5a57c0c630a53b4b7a0b48cb
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4651
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Just like bluetooth and wlan it need to be enabled in EC.
Set the appropriate bit in EC if CMOS config says so.
Change-Id: Ia48ca3201f013d3b4c4153f32ff536e06b6a2f6d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4516
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Most of the code needed for this is already in the tree with X201
patch series but code didn't know where to send the next screen
notification and so was disabled. Define right video device.
Tested by: Sam Noble
Change-Id: I4ff0d220afdca342617ce43c6e5d0164ad8eba27
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4494
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Instead of depending on exact mobo configure general characteristic whether
dock is configured in romstage or ramstage.
X60 and T60 have superio in dock so it needs to be inited to get serial, so
it should be inited in romstage.
On X201 there is nothing useful that early in boot but it's needed to init more
to get dock working, in particular EC init needs to be done first.
Change-Id: If5072e3dec883a94cd2d5643a92f7f6c3c9feee9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4294
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Instead define brightness up/down function and gfx device and use
preprocessor magic to glue it together.
Change-Id: I03074ae07b33c1546d229efc3e80606ddbee6300
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4282
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Do not directly check the return value of get_option, but instead compare
the returned value against a CB_CMOS_ error code, or against CB_SUCCESS.
Change-Id: I2fa7761d13ebb5e9b4606076991a43f18ae370ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Iefc481f09268dd15bbc3cbfa8bdd110d44383f6a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4281
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iec0abae8a4b18ac737e9ebb3eac219182729be0f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4057
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This reverts commit de1fe7f655c549e8dce5b34218221890fa5ccc34.
While things appeared to work, there were actually invalid references
to CAR storage after CAR was torn down on boards without
EARLY_CBMEM_INIT. It was discussed use of CAR_GLOBAL should be
restricted to boards that handle CAR migration properly.
Change-Id: I9969d2ea79c334a7f95a0dbb7c78065720e6ccae
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3968
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
If romstage does not make cbmem_initialize() call, linker should
optimize the code for CAR migration away.
This simplifies design of CBMEM console by a considerable amount.
As console buffer is now migrated within cbmem_initialize() call there
is no longer need for cbmemc_reinit() call made at end of romstage.
Change-Id: I8675ecaafb641fa02675e9ba3f374caa8e240f1d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3916
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Assume EARLY_CBMEM_INIT=y everywhere and remove option from Kconfig.
If romstage does not make the cbmem_initialize() call, features like
COLLECT_TIMESTAMPS and early CBMEM_CONSOLE will execute during
romstage, but that data will get lost as no CAR migration is
executed.
Change-Id: I5615645ed0f5fd78fbc372cf5c3da71a3134dd85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3917
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I87b454c748cf885491d5b38bfe53a2ec0e9f38c5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3910
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
