| Age | Commit message (Collapse) | Author |
|---|
|
Add required ASL files into dsdt.asl
TEST=Dump and disassemble DSDT and verify all ACPI devices are present.
Change-Id: I70829e2bdb12fad20627d9aea47e745d9095f07a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
List of changes:
1. Add devicetree.cb config parameters related to FSP-S UPD
2. Configure GPIO as per ADL-P RVP
3. Add files required for ramstage(ec.c, mainboard.c)
4. Add smihandler.c for SMM
5. Add devicetree changes as below
- USB OC PIN programing
- GPE configuration
- SATA port mapping
- LPSS configuration
- Audio configuration
- IA common SoC configuration
- EDP configuration
- TCSS USB configuration
- Enable S0ix
TEST=Able to boot ADL-P RVP without Chrome EC (using on-board EC) with
UART log over legacy UART0 port as 0x3f8 with NVME at RP9 reach till
depthcharge payload.
Change-Id: I120885956c88babfa09d24ce1079d49306919b8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enables Pcie M.2 support for WWAN and disable M.2 USB.
RP4 is already on and PcieRpEnable[3] is enabled. Clock source 2 is already
configured. Added missing gpio configuration.
BUG=none
TEST=Boot to OS, check WWAN functionality
Change-Id: Ie9b7915062b2ef65d881d478e64322c0b8765614
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45828
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I6f4d0bf9adc1cce4942a16675a072ffea00bd2e0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Refer to commit d7b88dc (mb/google/x86-boards: Get rid of power button
device in coreboot)
This change gets rid of the generic hardware power button from all
intel mainboards and relies completely on the fixed hardware power
button.
Change-Id: I8f9d73048041d42d809750fdb52092f40ab8f11f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It builds same binary for intel/d945gclf using BUILD_TIMELESS=1
Change-Id: Ic48008719a9cf6942ae8cdaebaab6ba43e665489
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45281
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generated buils/dsdt.dsl for intel/kblrvp11 are same.
Change-Id: I41195be171b48f41fe2955e4639d8b770853d483
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
- This change is required to execute EC sync in coreboot instead
of depthcharge
Bug=none
Test=build and boot coreboot on TGLRVP
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I40ae104d4de93c12097e049253a33b23a46c6203
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44689
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bug=none
Test=emerge build and boot on tglrvp and check that
tpm is probed successfully from coreboot.
Cq-Depend:chromium-review:1881839
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I4a3aec98f72524e8e2a1834878ef75b9f933ae3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
|
|
List of changes:
1. Add DDR4 and LPDDR4 memory related code
- SPD for LPDDR4
- DQ byte map
- DQS CPU-DRAM map
- Rcomp resistor
- Rcomp target
2. Fill FSP-M related UPD parameters
3. Add devicetree.cb config parameters related to FSP-M UPD
TEST=Able to build and boot ADL-P RVP till ramstage early
Change-Id: Iffc5c17ed0725f61c8c274a80a1d27161ca6cebf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Initial code block to select SOC_INTEL_ALDERLAKE Kconfig
2. Add minimum code to make ADL-P RVP build successfully
3. Mainly bootblock and verstage code added to reach till verstage
4. Add support for 2 mainboards as ADL-P board with default EC (Windows
SKU) and Chrome EC (Chrome SKU)
5. Add empty dsdt.asl to avoid compilation error
TEST=Able to build and boot ADL-P RVP till romstage early.
Change-Id: I2b551f48a4eb4d621d9a86c5d189c517d5610069
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEST=Able to build TGLRVP and JSLRVP.
Change-Id: Ie07df9f59015092a4c2a27b1451f0d556c70f0d8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Delete SoC local copy of ipu.asl and refer from common block ipu.asl
TEST=Dump and disassemble DSDT on tglrvp, verify IPU0 device
present there.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I6a0f8a919092f7bbcd64d4791746d30fdee33894
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move and use the common xeon_sp/cpx/acpi asl for skx/.
There were only minor whitespace differences between the directories.
Update the mainboards to build the moved files.
TiogaPass coreboot.rom checked with BUILD_TIMELESS.
Change-Id: I5058a3fe8d96075a266fb92f10707bb94308c85b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45217
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
displays for TGL-Y RVP
- Enable DDC pins for DDI-B
- Enable HPD pins for DDI-1/DDI-2
- Update MPHY/USB2 Mapping to match with the TGL-Y RVP schematic
BUG: System not able to detect displays attached to onboard micro-HDMI or Type-C connectors
TEST: hot-plug/unplug HDMI displays with onboard micro-HDMI connector and USB Type-C connectors to make sure the displays get detected and enabled
Change-Id: I08a1b16a8fa45cf0f366661395b9f2aa25c44935
Signed-off-by: Jason Le <jason.v.le@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change allows treating the PMC as a 'hidden' PCI device on
JasperLake, so that the MMIO & I/O resources can be exposed as
belonging to this device, instead of the system agent and LPC/eSPI.
Original patch for jasperlake SoC here:
CB:42018
This change was missing for JasperLake rvp board.
TEST=Checked PMC init function is called and also checked PCI resource
for PMC device 1f.2.
Change-Id: I7531d32c62d3f9735938f744f2892ab9c9bebddf
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add DTT (Dynamic Tuning Technology) support for Tiger Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=None
TEST=Build and boot on tglrvp board
Change-Id: I0dbee370b8dc9e1e3ae6f1a1101047ac6fd76f53
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=none
TEST=Build for Tigerlake RVP and boot to OS. Test if following sysfs is populated.
cat /sys/devices/system/cpu/intel_pstate/
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Change-Id: Ie3d9691e149a6fbc19c6691896126d04c680fde3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45609
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The name GENERIC_SPD_BIN doesn't reflect anymore what that config is
used for, so rename it to HAVE_SPD_BIN_IN_CBFS.
Change-Id: I4004c48da205949e05101039abd4cf32666787df
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45147
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop GENERIC_SPD_BIN from boards selecting it, despite having no
soldered memory.
Change-Id: Id05fe45007d5662ff9bee326f28470df1206fcff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45146
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable processor thermal control using PCI dev path function instead of
Device4Enable parameter in devicetree. This change removes the dependency
on Device4Enable in devicetree. We can enable and disable this thermal
control using on and off support with PCI device entry in devicetree.
BRANCH=None
BUG=None
TEST=Built and tested on dedede board
Change-Id: I0463236996ad001af506c9966840b27fe44d60d2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
CSE Lite SKU is CSE FW designed for Chrome and this enables CSE Lite SKU
support for tglrvp.
BUG=None
TEST=Build and boot tglrvp with CSE Lite and Consumer SKU
Change-Id: Ia5f3e8125b5e7760a62f7fb46aeeae85c32e2037
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41132
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3fdc521d30155c4275c336afe03244311f584e71
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44617
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is to enable Intel ME communication interface HECI1 by
devicetree for PAVP with CSE Lite.
PAVP feature is enabled with CSE Lite SKU for Chrome and HECI1 interface
is required between kernel and CSE Lite.
BUG=None
TEST=Build and boot tglrvp. Run lspci and check pcie device
00:16.0 Communication controller: Intel Corporation Device a0e0
Change-Id: I23117fa96503942e6a72765dd3fd1cc762e3f705
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable CSE PCI device Bus 0: Device 0x0f: Function 0x00 to let
Intel common cse block code can use this device.
Calling me_read_config32(offset) function from ramstage:
Without this CL :
HECI: Global Reset(Type:1) Command
BUG: me_read_config32 requests hidden 00:0f.0
PCI: dev is NULL!
With this CL :
HECI: Global Reset(Type:1) Command
HECI: Global Reset success!
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I97d221ae52b4b03ecd859d708847ad77fe4bf465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This allows us to drop some casts to uintptr_t around the tree.
The MCHBAR32 macro still needs a cast to preserve reproducibility.
Only the native raminit path needs the cast, the MRC path does not.
Tested with BUILD_TIMELESS=1, these boards remain identical:
- Lenovo ThinkPad X230
- Dell OptiPlex 9010
- Roda RW11 (with MRC raminit)
Change-Id: I8ca1c35e2c1f1b4f0d83bd7bb080b8667dbe3cb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45349
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
RCBA is located in the PCH. Replace all instances with the
already-defined `DEFAULT_RCBA` macro, which is equivalent.
Change-Id: I4b92737820b126d32da09b69e09675464aa22e31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45348
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable -> Enable
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: Iccefb02fa9bf9507b9e679b3fba35c5c28d677a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For consistency with other platforms, use `SOC_INTEL_GEMINILAKE`.
Change-Id: I06310e5a9bca6c9504f19a6c2fe9b26626f290d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add DTT (Dynamic Tuning Technology) support for Jasper Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=Noe
TEST=Build and boot on jslrvp board
Change-Id: I41409c70d8472c54ca452fc98d5ee9edf3ccd307
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
CPU_INTEL_HASWELL is already selected at nb/intel/haswell/Kconfig.
Change-Id: I608286aae72bc740be642a72109472fb235f37bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
'CONSOLE_SERIAL' is already set to 'y' at src/console/Kconfig.
Change-Id: I350cf12a115c6ebe54a2b0821edc94c29db8d137
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
These changes are according to spd_binary_optimization_volteer_v0.4 sheet.
Offset Current value Updated value Analysis
1 0x10 0x11 As per SPD spec rev 1.1
5 0x19 0x21 16 bits for Row addrs, 10 bits for Column addrs
6 0x95 0xB5 4 die, 2 ch per pkg, Byte 16 signal matrix
12 0x02 0x0A 2 ranks per ch, 16 bits device data width
18 0x05 0x04 4267MHz support
29 0x90 0xC0 HW specific
30 0x06 0x68 HW specific
31 0xD0 0x60 HW specific
32 0x02 0x04 HW specific
125 0x00 0xE1 4267MHz support
BUG=b:159319534
TEST=Tested multiple cold boot cycles on TGL-UP3 with QS silicon
Change-Id: Ie506fbfe86a3ffb77763e8d9ef7e8aa69ea44bd3
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42524
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Includes changes related to GPIO pad to configure I2C4 required for UFC
Change-Id: Ica3ac31f10214b8aff3bb64a2c3b42ccfa28bdcd
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This change updates devicetree to enable I2C4 bus required for the UFC
Change-Id: Iade1b64fa3dc890a896fb987fdc8d68db7db5e5f
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Jasper Lake SoC had PCI root port mapping swap, thats why we were
using swapped mapping earlier for all the boards
Recently, patch was pushed to handle this swap in PCI enumeration code
for Jasper Lake and we need to correct this mapping. Now this mapping
aligns with actual port mapping in the schematics
BUG=None
BRANCH=None
TEST=NVMe and WLAN are getting detected after this changes
Change-Id: Ide5f8419a15f559cefeb6039f155fabf97c279f8
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Allow configuring FSP option PcieRpSlotImplemented. Also, update all
related devicetrees and configure PcieRpSlotImplemented to keep the
current behaviour.
Change-Id: I6c57ab0ae50a37cd9a90786134e9056851a86a3c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tiger Lake External Design Specification (Document #575683) states UP4
TBT_PCIE3 is not applicable. Disable TC3 for UP4.
BUG=None
Test=Built UP4 image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Icff8fccf9ac29c315c2a4dd08a3ec8a8efe9c453
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44572
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures user facing camera related GPIOs
as per schematics.
1. GPP_D5 pwr_en
2. GPP_B14 reset
3. GPP_E0 clock
4. GPP_D12 I2C4b
5. GPP_D13 I2C4b
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: I026c16f73cf597614efaea3e0f0ab1e2cfe1e211
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44416
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Increase DDR Frquency limit to support data rate 4266 Mbps
Bug=None
Test=Build and boot on tglrvp hardware;
$dmidecode --type 17 reflects memory Speed = 4266
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I8185ebbaa32a01fee104bc0b757fc4adb58bba97
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44149
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.corp-partner.google.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
More space is required in the COREBOOT CBFS to accommodate some features.
Currently no alternate firmware is stuffed into RW_LEGACY CBFS and has
~1 MB of unused space. Borrow some space from RW_LEGACY CBFS and extend
the RO_SECTION. Even within RO_SECTION, GBB requires only 12 KiB. So
adjust the GBB region accordingly and extend the COREBOOT CBFS.
BUG=b:162159386
TEST=Build the JSLRVP mainboard.
Change-Id: Ia8bb381c31ddf76f3211f9d4ac5c8c18c27834b7
Signed-off-by: Karthikeyan Ramasubramanain <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Receiver enable results are now saved in flash.
Change-Id: Ib1a985147b081860c58d1649c4e50301b8144b0c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44251
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the SLP_Sx assertion widths and power cycle duration
for the Japerlake RVP.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159104150
TEST=Verified that the power cycle duration is ~1.2s with global
reset on JSLRVP.
Change-Id: Ie2a8d959d7ebbf9c24f8c4e8d5c68b70e0ac5708
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch sets the GPP_H1 to PAD_CFG_GPO which is general
purpose output with no pullup/down. We need this GPIO for
the detection of soundcard in TGL RVP's.
BUG=none
BRANCH=none
TEST=Build and boot tglrvp successfully. From "aplay -l"
output check that soundcards are listed properly.
Change-Id: Ic0ef33079af7940360c986efacabd6d367aad516
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Interrupt _CRS is missing under CREC scope. TGLRVP U/Y has GPP_A15
assigned to MECC_HPD2 as EC_SYNC_IRQ. Configure this GPP_A15 GPIO as
active low and level interruptible for EC sync interrupt configuration.
BUG=None
TEST=Booted to kernel and verified EC_SYNC_IRQ in the scope of CREC
current resource settings.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Idfe4d4e800866805ee8d758028ac7ddf4b259faa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44103
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also remove the meaningless `sata_traffic_monitor` devicetree option.
Function parameters will be removed in a reproducible follow-up.
Change-Id: I70cf1e06cc8ace504a22be9f9c4441e3070f9e29
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
BUG=none
BRANCH=none
TEST=Build and boot TGL-UP3 RVP with QS silicon successfully.
Change-Id: I5b84457a1455edfe500ce80ba7f7ca6ccce43666
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43276
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, CIO gets enabled by the option Cio2Enable, but this
duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the CIO controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Cio2Enable setting, and missing entries
were added.
Change-Id: I65e2cceb65add66e3cb3de7071b1a3cc967ab291
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, SA IMGU gets enabled by the option SaImguEnable,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SA IMGU controller.
All corresponding mainboards were checked if the devicetree
configuration matches the SaImguEnable setting, and missing entries
were added.
Change-Id: I293a20a321c75f82a57cbd5339656d93509b7aa6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
RVP11 and RVP3 set it to zero, the other two omit the setting.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I6b393f0f2269f62b415456c17ba5962f46a1c5d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43909
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
RVP8 does not set it, and the other variants set it to zero. So, factor
it out.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I67c958af2dc955d07b895dc93fbe2232dbd48d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43908
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates devicetree to enable SSDT generation for world
facing and user facing cameras of jasperlake_rvp. Also removes DSDT
changes related to the world facing camera.
Change-Id: Ib439572bc1d15ef02c86c7bfa88af6b16eb06f97
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use tabs instead of eight (sometimes less) spaces.
Change-Id: Ic3d61f5210d21d9613fc50b47b90af71f544169a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Some UPD options are already set in `xeon_sp/cpx/romstage.c`. Remove
them from the board configuration to avoid duplicating this code.
Change-Id: Ic79245103c33427e06c7ea881be778e3d219c45f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43924
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to src/vendorcode/intel/fsp/fsp2_0/cooperlake_sp/FspmUpd.h,
use FSP_M_CONFIG structure fields to configure UPD options for FSP-M
in romstage instead of raw offsets.
Change-Id: Idb25d8954b09805b496ab97b341a8ef1ac38bb6a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The only reason to use a named choice statement is if you plan on
having the choice statement in multiple places. Since the `TGL_EC`
name is not used anywhere else, we might as well get rid of it.
Change-Id: Ic0bddefd007ef961bbff61fd656475cae78148e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It is expected both of TCSS D3Hot and D3Cold are enabled by default.
BUG=None
TEST=Verified both of TCSS D3Hot and D3Cold configuration on TGLRVP.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Id569d8191f82f12379b57a9c50aec31776220bb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Currently HDA gets enabled by the option EnableAzalia, but
this duplicates the devicetree on/off options. Therefore use
the on/off options for the enablement of the HDA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableAzalia setting.
Change-Id: Id20d023b2f286753fb223050292c7514632e1dd3
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43866
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently HECI3 gets enabled by the option Heci3Enabled, but
this duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the HECI3 controller.
I checked all corresponding mainboards if the devicetree configuration
matches the Heci3Enabled setting.
Change-Id: I4f99d434dfee49a9783e38c3910b9391d479cb83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43864
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently LAN gets enabled by the option EnableLan, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the LAN controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableLan setting.
Change-Id: I36347e8e0f0ddba47aec52aeb6bc047e3c8bfaa4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
This change updates TGLRVP configuration to have USB Type-C connector
device properties filled into ACPI SSDT.
TEST=Built and booted to kernel on tglrvp boards. Verified the USBC
scope under LPCB.EC0.CREC with required connector device properties.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ifd4c59afb3b8a222598fd4ff36d72c4b877bdad2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Two usb Type-C ports under the actual mux device. Each port has its own
ACPI device entry. These nodes are the ones that the USB Type-C
port/connector device will refer to in order to configure the mux.
TEST=Built image-tglrvp-up4.bin successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I8423ddbb5bc189899a9e19e7da6e2ee7b7fecc18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All boards disable PIRQs, except purism/librem_bdw. Since IRQ0 is
invalid and modern OSes don't use PIRQ routing, disable the PIRQs.
Change-Id: I93b074474c3c6d4329903cab928dc41e1d3a3fb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Fixes a bug in Makefile.inc, which did not allow building ROM image
with ramstage.c from motherboard configuration.
Change-Id: I70d8a2e1f53e2fa56d514361116a55f175407753
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43457
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
- Update MAINBOARD_PART_NUMBER for TGL variants
- MAINBOARD_PART_NUMBER is reported as FRID on acpi
- This is required for cros_config to differentiate
across TGL variants.
- Mosys uses cros_config to identify TGL variants using
data read from FRID
Bug=none
Test=build and boot coreboot on TGLRVP UP3 hardware
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
Change-Id: I7a6ddf95d085490d52e00ade7bac23e8c8849427
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42865
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change.
Change-Id: I6375f97bc2a30beba5882792328f26e0675621cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43867
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set this fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Ie3ee2eadc08826d49e8517c83ab6831398e3aa93
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43455
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables CSE Lite SKU for jasperlake rvp.
BUG=b:160201335
BRANCH=None
TEST=Build and boot jasperlake rvp with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I60039ffb1f24cf98f55e83d8c8649745598aa43a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40571
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the SkipCpuReplacementCheck config for jasperlake rvp
to avoid the forced MRC training with the soldered down SOC.
BUG=b:160201335
BRANCH=None
TEST=Build and verify on jasperlake rvp with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I40fb9a25170e8db3c63a71428ba459160a918961
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43146
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make it default to 0x400, which is what the touched southbridges use.
Change-Id: I95cb1730d5bf6f596ed1ca8e7dba40b6a9e882fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Found using:
diff <(git grep -l '#include <cpu/x86/msr.h>' -- src/) <(git grep -l 'IA32_EFER\|EFER_\|TSC_MSR\|IA32_\|FEATURE_CONTROL_LOCK_BIT\|FEATURE_ENABLE_VMX\|SMRR_ENABLE\|CPUID_\|SGX_GLOBAL_ENABLE\|PLATFORM_INFO_SET_TDP\|SMBASE_RO_MSR\|MCG_CTL_P\|MCA_BANKS_MASK\|FAST_STRINGS_ENABLE_BIT\|SPEED_STEP_ENABLE_BIT\|ENERGY_POLICY_\|SMRR_PHYSMASK_\|MCA_STATUS_\|VMX_BASIC_HI_DUAL_MONITOR\|MC0_ADDR\|MC0_MISC\|MC0_CTL_MASK\|msr_struct\|msrinit_struct\|soc_msr_read\|soc_msr_write\|rdmsr\|wrmsr\|mca_valid\|mca_over\|mca_uc\|mca_en\|mca_miscv\|mca_addrv\|mca_pcc\|mca_idv\|mca_cecc\|mca_uecc\|mca_defd\|mca_poison\|mca_sublink\|mca_err_code\|mca_err_extcode\|MCA_ERRCODE_\|MCA_BANK_\|MCA_ERRTYPE_\|mca_err_type\|msr_set_bit\|msr_t\|msrinit_t' -- src/) |grep '<'
Change-Id: I45a41e77e5269969280e9f95cfc0effe7f117a40
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41969
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found using:
diff <(git grep -l '#include <stdint.h>' -- src/) <(git grep -l 'int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX' -- src/) |grep -v vendorcode |grep '<'
Change-Id: I5e14bf4887c7d2644a64f4d58c6d8763eb74d2ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41827
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Files found using:
diff <(git grep -l '#include <types.h>' -- src/) <(git grep -l 'BIT(\|size_t\|wchar_t\|wint_t\|NULL\|DEVTREE_EARLY\|DEVTREE_CONST\|MAYBE_STATIC_NONZERO\|zeroptr\|int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX\|bool\|true\|false\|cb_err\|CB_SUCCESS\|CB_ERR\|CB_ERR_ARG\|CB_CMOS_\|CB_KBD_\|CB_I2C_\|cb_err_t\|DIV_ROUND_CLOSEST\|container_of\|__unused\|alloca(\|ARRAY_SIZE\|ALIGN\|ALIGN_UP\|ALIGN_DOWN\|IS_ALIGNED\|__CMP_UNSAFE\|MIN_UNSAFE\|MAX_UNSAFE\|__CMP_SAFE\|__CMP\|MIN(\|MAX(\|ABS(\|IS_POWER_OF_2\|POWER_OF_2\|DIV_ROUND_UP\|SWAP(\|KiB\|MiB\|GiB\|KHz\|MHz\|GHz\|offsetof(\|check_member\|member_size' -- src/)|grep -v vendor |grep '<'
Change-Id: I5d99d844cc58d80acb505d98da9d3ec76319b2eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41677
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds SMI handler for SCI, S3/S5 wake up and LID closed
events on tglrvp platform.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0bc72f164e86f1921e0cad39f9749e8e3be0778f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change allows EC to change state of host-controlled USB MUX.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia7c331157b1b4039e42c373f5b130a66f7594458
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42955
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables PCIEXP_HOTPLUG to support resource allocation for
TCSS TBT/USB4.
BUG=b:149186922
Change-Id: Id3066204c8a780ade251c7be4052a60a861e43db
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Share "EC in RW" GPIO with depthcharge. Also we define the CONFIGS
needed CHROME, CHROME_EC and use the chrome lid and recovery.
BUG=None
BRANCH=None
TEST=Build and boot TGL RVP. Check recovery works with
crossystem recovery_request.
Change-Id: I1e88200e3f8418e5b0ab39ac65ed1b3545ce111e
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
This change enables s0ix for tglrvp up3 and up4 platform.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I657bee1d7ee120ae15ccb4a33f9eb2fcf5cca65a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42954
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CpuReplacementCheck for TGLRVP with a CPU socket.
Test=build and verified with tglrvp
Change-Id: I75b4a4609c172c341087077228e23c6d31a9e7e1
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: If2ebac5fcab278c97dfaf8adc9d1e125888acafe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43129
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
