Age | Commit message (Collapse) | Author |
|
These changes are according to spd_binary_optimization_volteer_v0.4 sheet.
Offset Current value Updated value Analysis
1 0x10 0x11 As per SPD spec rev 1.1
5 0x19 0x21 16 bits for Row addrs, 10 bits for Column addrs
6 0x95 0xB5 4 die, 2 ch per pkg, Byte 16 signal matrix
12 0x02 0x0A 2 ranks per ch, 16 bits device data width
18 0x05 0x04 4267MHz support
29 0x90 0xC0 HW specific
30 0x06 0x68 HW specific
31 0xD0 0x60 HW specific
32 0x02 0x04 HW specific
125 0x00 0xE1 4267MHz support
BUG=b:159319534
TEST=Tested multiple cold boot cycles on TGL-UP3 with QS silicon
Change-Id: Ie506fbfe86a3ffb77763e8d9ef7e8aa69ea44bd3
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42524
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Includes changes related to GPIO pad to configure I2C4 required for UFC
Change-Id: Ica3ac31f10214b8aff3bb64a2c3b42ccfa28bdcd
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This change updates devicetree to enable I2C4 bus required for the UFC
Change-Id: Iade1b64fa3dc890a896fb987fdc8d68db7db5e5f
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Jasper Lake SoC had PCI root port mapping swap, thats why we were
using swapped mapping earlier for all the boards
Recently, patch was pushed to handle this swap in PCI enumeration code
for Jasper Lake and we need to correct this mapping. Now this mapping
aligns with actual port mapping in the schematics
BUG=None
BRANCH=None
TEST=NVMe and WLAN are getting detected after this changes
Change-Id: Ide5f8419a15f559cefeb6039f155fabf97c279f8
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Allow configuring FSP option PcieRpSlotImplemented. Also, update all
related devicetrees and configure PcieRpSlotImplemented to keep the
current behaviour.
Change-Id: I6c57ab0ae50a37cd9a90786134e9056851a86a3c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tiger Lake External Design Specification (Document #575683) states UP4
TBT_PCIE3 is not applicable. Disable TC3 for UP4.
BUG=None
Test=Built UP4 image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Icff8fccf9ac29c315c2a4dd08a3ec8a8efe9c453
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44572
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures user facing camera related GPIOs
as per schematics.
1. GPP_D5 pwr_en
2. GPP_B14 reset
3. GPP_E0 clock
4. GPP_D12 I2C4b
5. GPP_D13 I2C4b
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: I026c16f73cf597614efaea3e0f0ab1e2cfe1e211
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44416
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Increase DDR Frquency limit to support data rate 4266 Mbps
Bug=None
Test=Build and boot on tglrvp hardware;
$dmidecode --type 17 reflects memory Speed = 4266
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I8185ebbaa32a01fee104bc0b757fc4adb58bba97
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44149
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.corp-partner.google.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
More space is required in the COREBOOT CBFS to accommodate some features.
Currently no alternate firmware is stuffed into RW_LEGACY CBFS and has
~1 MB of unused space. Borrow some space from RW_LEGACY CBFS and extend
the RO_SECTION. Even within RO_SECTION, GBB requires only 12 KiB. So
adjust the GBB region accordingly and extend the COREBOOT CBFS.
BUG=b:162159386
TEST=Build the JSLRVP mainboard.
Change-Id: Ia8bb381c31ddf76f3211f9d4ac5c8c18c27834b7
Signed-off-by: Karthikeyan Ramasubramanain <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Receiver enable results are now saved in flash.
Change-Id: Ib1a985147b081860c58d1649c4e50301b8144b0c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44251
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the SLP_Sx assertion widths and power cycle duration
for the Japerlake RVP.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159104150
TEST=Verified that the power cycle duration is ~1.2s with global
reset on JSLRVP.
Change-Id: Ie2a8d959d7ebbf9c24f8c4e8d5c68b70e0ac5708
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch sets the GPP_H1 to PAD_CFG_GPO which is general
purpose output with no pullup/down. We need this GPIO for
the detection of soundcard in TGL RVP's.
BUG=none
BRANCH=none
TEST=Build and boot tglrvp successfully. From "aplay -l"
output check that soundcards are listed properly.
Change-Id: Ic0ef33079af7940360c986efacabd6d367aad516
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Interrupt _CRS is missing under CREC scope. TGLRVP U/Y has GPP_A15
assigned to MECC_HPD2 as EC_SYNC_IRQ. Configure this GPP_A15 GPIO as
active low and level interruptible for EC sync interrupt configuration.
BUG=None
TEST=Booted to kernel and verified EC_SYNC_IRQ in the scope of CREC
current resource settings.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Idfe4d4e800866805ee8d758028ac7ddf4b259faa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44103
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also remove the meaningless `sata_traffic_monitor` devicetree option.
Function parameters will be removed in a reproducible follow-up.
Change-Id: I70cf1e06cc8ace504a22be9f9c4441e3070f9e29
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
BUG=none
BRANCH=none
TEST=Build and boot TGL-UP3 RVP with QS silicon successfully.
Change-Id: I5b84457a1455edfe500ce80ba7f7ca6ccce43666
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43276
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, CIO gets enabled by the option Cio2Enable, but this
duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the CIO controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Cio2Enable setting, and missing entries
were added.
Change-Id: I65e2cceb65add66e3cb3de7071b1a3cc967ab291
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, SA IMGU gets enabled by the option SaImguEnable,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SA IMGU controller.
All corresponding mainboards were checked if the devicetree
configuration matches the SaImguEnable setting, and missing entries
were added.
Change-Id: I293a20a321c75f82a57cbd5339656d93509b7aa6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
RVP11 and RVP3 set it to zero, the other two omit the setting.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I6b393f0f2269f62b415456c17ba5962f46a1c5d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43909
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
RVP8 does not set it, and the other variants set it to zero. So, factor
it out.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I67c958af2dc955d07b895dc93fbe2232dbd48d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43908
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates devicetree to enable SSDT generation for world
facing and user facing cameras of jasperlake_rvp. Also removes DSDT
changes related to the world facing camera.
Change-Id: Ib439572bc1d15ef02c86c7bfa88af6b16eb06f97
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use tabs instead of eight (sometimes less) spaces.
Change-Id: Ic3d61f5210d21d9613fc50b47b90af71f544169a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Some UPD options are already set in `xeon_sp/cpx/romstage.c`. Remove
them from the board configuration to avoid duplicating this code.
Change-Id: Ic79245103c33427e06c7ea881be778e3d219c45f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43924
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to src/vendorcode/intel/fsp/fsp2_0/cooperlake_sp/FspmUpd.h,
use FSP_M_CONFIG structure fields to configure UPD options for FSP-M
in romstage instead of raw offsets.
Change-Id: Idb25d8954b09805b496ab97b341a8ef1ac38bb6a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The only reason to use a named choice statement is if you plan on
having the choice statement in multiple places. Since the `TGL_EC`
name is not used anywhere else, we might as well get rid of it.
Change-Id: Ic0bddefd007ef961bbff61fd656475cae78148e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
It is expected both of TCSS D3Hot and D3Cold are enabled by default.
BUG=None
TEST=Verified both of TCSS D3Hot and D3Cold configuration on TGLRVP.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Id569d8191f82f12379b57a9c50aec31776220bb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Currently HDA gets enabled by the option EnableAzalia, but
this duplicates the devicetree on/off options. Therefore use
the on/off options for the enablement of the HDA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableAzalia setting.
Change-Id: Id20d023b2f286753fb223050292c7514632e1dd3
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43866
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently HECI3 gets enabled by the option Heci3Enabled, but
this duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the HECI3 controller.
I checked all corresponding mainboards if the devicetree configuration
matches the Heci3Enabled setting.
Change-Id: I4f99d434dfee49a9783e38c3910b9391d479cb83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43864
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
Currently LAN gets enabled by the option EnableLan, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the LAN controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableLan setting.
Change-Id: I36347e8e0f0ddba47aec52aeb6bc047e3c8bfaa4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
This change updates TGLRVP configuration to have USB Type-C connector
device properties filled into ACPI SSDT.
TEST=Built and booted to kernel on tglrvp boards. Verified the USBC
scope under LPCB.EC0.CREC with required connector device properties.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ifd4c59afb3b8a222598fd4ff36d72c4b877bdad2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Two usb Type-C ports under the actual mux device. Each port has its own
ACPI device entry. These nodes are the ones that the USB Type-C
port/connector device will refer to in order to configure the mux.
TEST=Built image-tglrvp-up4.bin successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I8423ddbb5bc189899a9e19e7da6e2ee7b7fecc18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All boards disable PIRQs, except purism/librem_bdw. Since IRQ0 is
invalid and modern OSes don't use PIRQ routing, disable the PIRQs.
Change-Id: I93b074474c3c6d4329903cab928dc41e1d3a3fb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Fixes a bug in Makefile.inc, which did not allow building ROM image
with ramstage.c from motherboard configuration.
Change-Id: I70d8a2e1f53e2fa56d514361116a55f175407753
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43457
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
- Update MAINBOARD_PART_NUMBER for TGL variants
- MAINBOARD_PART_NUMBER is reported as FRID on acpi
- This is required for cros_config to differentiate
across TGL variants.
- Mosys uses cros_config to identify TGL variants using
data read from FRID
Bug=none
Test=build and boot coreboot on TGLRVP UP3 hardware
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
Change-Id: I7a6ddf95d085490d52e00ade7bac23e8c8849427
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42865
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, its coreboot.rom does not change.
Change-Id: I6375f97bc2a30beba5882792328f26e0675621cc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43867
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set this fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Ie3ee2eadc08826d49e8517c83ab6831398e3aa93
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43455
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables CSE Lite SKU for jasperlake rvp.
BUG=b:160201335
BRANCH=None
TEST=Build and boot jasperlake rvp with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I60039ffb1f24cf98f55e83d8c8649745598aa43a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40571
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the SkipCpuReplacementCheck config for jasperlake rvp
to avoid the forced MRC training with the soldered down SOC.
BUG=b:160201335
BRANCH=None
TEST=Build and verify on jasperlake rvp with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I40fb9a25170e8db3c63a71428ba459160a918961
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43146
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make it default to 0x400, which is what the touched southbridges use.
Change-Id: I95cb1730d5bf6f596ed1ca8e7dba40b6a9e882fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Found using:
diff <(git grep -l '#include <cpu/x86/msr.h>' -- src/) <(git grep -l 'IA32_EFER\|EFER_\|TSC_MSR\|IA32_\|FEATURE_CONTROL_LOCK_BIT\|FEATURE_ENABLE_VMX\|SMRR_ENABLE\|CPUID_\|SGX_GLOBAL_ENABLE\|PLATFORM_INFO_SET_TDP\|SMBASE_RO_MSR\|MCG_CTL_P\|MCA_BANKS_MASK\|FAST_STRINGS_ENABLE_BIT\|SPEED_STEP_ENABLE_BIT\|ENERGY_POLICY_\|SMRR_PHYSMASK_\|MCA_STATUS_\|VMX_BASIC_HI_DUAL_MONITOR\|MC0_ADDR\|MC0_MISC\|MC0_CTL_MASK\|msr_struct\|msrinit_struct\|soc_msr_read\|soc_msr_write\|rdmsr\|wrmsr\|mca_valid\|mca_over\|mca_uc\|mca_en\|mca_miscv\|mca_addrv\|mca_pcc\|mca_idv\|mca_cecc\|mca_uecc\|mca_defd\|mca_poison\|mca_sublink\|mca_err_code\|mca_err_extcode\|MCA_ERRCODE_\|MCA_BANK_\|MCA_ERRTYPE_\|mca_err_type\|msr_set_bit\|msr_t\|msrinit_t' -- src/) |grep '<'
Change-Id: I45a41e77e5269969280e9f95cfc0effe7f117a40
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41969
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found using:
diff <(git grep -l '#include <stdint.h>' -- src/) <(git grep -l 'int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX' -- src/) |grep -v vendorcode |grep '<'
Change-Id: I5e14bf4887c7d2644a64f4d58c6d8763eb74d2ed
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41827
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Files found using:
diff <(git grep -l '#include <types.h>' -- src/) <(git grep -l 'BIT(\|size_t\|wchar_t\|wint_t\|NULL\|DEVTREE_EARLY\|DEVTREE_CONST\|MAYBE_STATIC_NONZERO\|zeroptr\|int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX\|bool\|true\|false\|cb_err\|CB_SUCCESS\|CB_ERR\|CB_ERR_ARG\|CB_CMOS_\|CB_KBD_\|CB_I2C_\|cb_err_t\|DIV_ROUND_CLOSEST\|container_of\|__unused\|alloca(\|ARRAY_SIZE\|ALIGN\|ALIGN_UP\|ALIGN_DOWN\|IS_ALIGNED\|__CMP_UNSAFE\|MIN_UNSAFE\|MAX_UNSAFE\|__CMP_SAFE\|__CMP\|MIN(\|MAX(\|ABS(\|IS_POWER_OF_2\|POWER_OF_2\|DIV_ROUND_UP\|SWAP(\|KiB\|MiB\|GiB\|KHz\|MHz\|GHz\|offsetof(\|check_member\|member_size' -- src/)|grep -v vendor |grep '<'
Change-Id: I5d99d844cc58d80acb505d98da9d3ec76319b2eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41677
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds SMI handler for SCI, S3/S5 wake up and LID closed
events on tglrvp platform.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0bc72f164e86f1921e0cad39f9749e8e3be0778f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change allows EC to change state of host-controlled USB MUX.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia7c331157b1b4039e42c373f5b130a66f7594458
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42955
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables PCIEXP_HOTPLUG to support resource allocation for
TCSS TBT/USB4.
BUG=b:149186922
Change-Id: Id3066204c8a780ade251c7be4052a60a861e43db
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Share "EC in RW" GPIO with depthcharge. Also we define the CONFIGS
needed CHROME, CHROME_EC and use the chrome lid and recovery.
BUG=None
BRANCH=None
TEST=Build and boot TGL RVP. Check recovery works with
crossystem recovery_request.
Change-Id: I1e88200e3f8418e5b0ab39ac65ed1b3545ce111e
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
This change enables s0ix for tglrvp up3 and up4 platform.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I657bee1d7ee120ae15ccb4a33f9eb2fcf5cca65a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42954
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CpuReplacementCheck for TGLRVP with a CPU socket.
Test=build and verified with tglrvp
Change-Id: I75b4a4609c172c341087077228e23c6d31a9e7e1
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: If2ebac5fcab278c97dfaf8adc9d1e125888acafe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43129
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
And use it instead of directly writing to the MRC struct.
Change-Id: I7f04db29a08512c1a8b2b2300dba71cb3b84a5c5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Check the PCH's LPC device ID to know the system type instead of relying
on hardcoded numbers. The `get_pch_platform_type` function is MRC-safe.
Change-Id: Icfe7c2dccb7c7a178892ad3a2e34ca93b33b2bb9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43124
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Several of these includes are no longer necessary. Get rid of them.
Since "raminit.h" already includes "pei_data.h", we can omit including
the latter for brevity's sake.
Change-Id: Ia7e9dadf87114ca9ea4761b89909ea035cdfc38a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43121
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All mainboards choose the maximum speed of DDR3-1600.
Change-Id: I8863f9d1df950b924f596689ebf1bfda5d317e06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43120
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All mainboards have a non-zero SPD address to implemented DIMM slots.
Knowing this, it is possible to compute the MRC slot population masks
automatically instead of hardcoding the values on each mainboard.
Change-Id: Ia8f369dd1228d53d64471e48700e870e01e77837
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43119
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to redefine common settings.
Change-Id: If0cbc147791496bafc85831c1f88d3eb71b63350
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
This is what sandybridge does, and if done properly allows factoring out
common settings. Said refactoring will be handled in subsequent commits.
Change-Id: I075eba1324a9e7cbd47e776b097eb940102ef4fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
The DxxIR (Device xx Interrupt Route) registers in RCBA are 16-bit wide,
so do not use 32-bit operations to program them.
Note that the DxxIP (Device xx Interrupt Pin) registers are 32-bit, so
using 32-bit operations on them is correct.
Change-Id: I9699b98d5fcd26b2c710bf018f16acc65dcb634e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
It only contains a pointer to another struct. Flatten it.
Change-Id: Iab427592c332646e032a768719fc380c5794086b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Instead of using function pointers, we can use weak functions. So, drop
the pointer from `romstage_params`, leaving `pei_data` as the only
remaining member. This will be cleaned up in a follow-up commit.
Change-Id: I3b17d21ea7a650734119a5cab4892fcb158b589d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This code is not even being build-tested. Drop it before it grows moss.
Change-Id: I6948a0b9a6b699cb44e3e02d9e134180bac2fa14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
|
|
This simplifies things and makes type checking possible.
Change-Id: Iefc9baabae286aac2f2c46853adf1f6edf01586f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Instead of passing around a pointer to an array, just write the relevant
registers directly. Note that intel/baskingridge used spaces to indent
line continuations and had to be replaced with tabs to quell Jenkins.
Change-Id: Ifa06a2ab24da9b8c6aac6480542fa32d04f6d6fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Refer to commit 7736bfc
TEST=Able to build and boot TGLRVP.
Change-Id: Ie9a97cee7d7793077167db3a642dcbca45b09427
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43139
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will allow dropping the pointer inside romstage_params.
Change-Id: I04b695cbe2a6485b42ab037f4f7359a2429c3440
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Comments stating that this was mainboard-specific were very wrong.
Change-Id: I7026ca9c7dabd01b4a0c0549b697e006d5f75eb8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Two usb Type-C ports under the actual mux device. Each port has its own
ACPI device entry. These nodes are the ones that the USB Type-C
port/connector device will refer to in order to configure the mux.
TEST=Verified the scope of PMC.MUX CONx in the SSDT on Tigerlake RVP
board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I7210e00cebe16a5fb8417ac23abad98e574e0982
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42953
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4d62a04778c8f634b48eee459808f640451b9b48
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: Ic9f2e44692b20c2efabc468b10ec531e8b5a3e59
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41706
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3fad7cb2ac0b88adbe75acfa7a17f5a9b0bde6c2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41705
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If25ed7b5cc545abcbf16af66173058dde75260f7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41703
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7b657750b10f98524f011f5254e533217fe94fd8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Bring all GNVS related initialisation function to global
scope to force identical signatures. Followup work is
likely to remove some as duplicates.
Change-Id: Id4299c41d79c228f3d35bc7cb9bf427ce1e82ba1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42489
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I920e5e6a3fa92ede4a0b0388962b55208a7dee48
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: Ie9635e10dffe2f5fbef7cfbd556c3152dee58ccc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Kconfig 4.17 started using the $(..) syntax for environment variable
expansion while we want to keep expansion to the build system.
Older Kconfig versions (like ours) simply drop the escapes, not
changing the behavior.
While we could let Kconfig expand some of the variables, that only
splits the handling in two places, making debugging harder and
potentially messing with reproducible builds (e.g. when paths end up
in configs), so escape them all.
Change-Id: Ibc4087fdd76089352bd8dd0edb1351ec79ea4faa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
At least one mobile 945 series northbridge supports 4 threads, because
the dual-core Atom 330 CPU supports Hyper-threading. Therefore, we use
that as the default for this chipset.
Change-Id: I899ed1644d9b2da4fc72f09233a421200770110d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41845
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pineview has at most 4 threads.
Change-Id: I0f45f002d0bab0345bc061ac3c7a29237a536cc5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41843
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LGA775 CPUs can have at most 4 threads, and Eaglelake supports them.
As this socket is also used by other chipsets, temporarily place this
symbol into the northbridge scope until all chipsets are factored out.
Change-Id: I6e01363d995e135815cc70779e0cd5baf806cf60
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Board devicetrees requests for drivers/pc80/tpm but that
was not included for the build. Note that there is actually
no on-board TPM, just an LPC header connector on these boards.
Change-Id: Ia959ae9072e3fc709b779b1fc778eb82e10c2ee3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The prefix mainboard_ was used everywhere else.
Change-Id: Ie576fd47301aa484cb1396e0c6f7260b7698af4d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I13ed3b6e8608c37c1ebe51838e4052f89a638d83
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41947
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the boards do not select SYSTEM_TYPE_LAPTOP or _CONVERTIBLE
so their FADT preffered_pm_profile would change from PM_MOBILE without
the added overrides here.
Change-Id: I04b602b2c23fbd163fcd110a44ad25c6be07ab66
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41920
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9025ca3b6b438e5f9a790076fc84460342362fc2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41919
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for RT 1308 audio amplifier in TGLRVP.
We are using the i2c generic driver here to generate
the SSDT file. Datasheet:ALC-1308-CG-version-08.
BUG=none
BRANCH=none
TEST=Build and boot tglrvp successfully. In kernel console
use the "aplay -l" command to check soundcard is listed.
Change-Id: I41d205a3ab87db85baf49e9e8a582c226ba5832d
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Change-Id: Id0bb5266246dbd959c6497d7c411f908cc49318c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Boards have unconditional select EC_GOOGLE_CHROMEEC.
Change-Id: Id444c83fc40f908d2257e8ec2606f149722a9bde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This explicitly enables TCSS xHCI, PCIe root ports and DMA controllers
from TGL RVP platform devicetree setting.
BUG=:b:146624360
TEST=Built and booted on TGL RVP.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0111542eef253f469f679cdc4b81812438dff4ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Found using:
diff <(git grep -l '#include <cbfs.h>' -- src/) <(git grep -l 'cbfs_boot_map_optionrom\|cbfs_boot_map_optionrom_revision\|cbfs_boot_locate\|cbfs_boot_map_with_leak\|cbfs_locate_file_in_region\|cbfs_boot_load_file\|cbfs_load_and_decompress\|cbfs_prog_stage_load\|cbfs_boot_region_device' -- src/) |grep '<' |grep -v vendorcode
Also add missing 'include <cbfs.h>' in src/soc/qualcomm/sc7180/qupv3_config.c
Change-Id: Icaecb5b910888f34cddedab7b2f64eaf6d01ad66
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41682
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I54eda3d51ecda77309841e598f06eb9cea3babc1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|