| Age | Commit message (Collapse) | Author |
|---|
|
Especially on ICH7 failing to do so results in i2c block read being
unusable. On ICH10 this problem doesn't manifest itself that much.
This moves disabling the watchdog reboot to the northbridge code like
i945 (even though it technically is southbridge stuff).
TESTED on Intel DG41WV: hacking on raminit is much nicer since no
need to do a hard power down for +4s are needed to clear the timeouts.
Change-Id: Icfd3789312704f61000a417f23a121d02d2e7fbe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I0383dd9b582d5c77be66ecd74bcf1a438f874cc7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set SuperIO GPIO like vendor firmware.
Change-Id: I46a48776382eb0d9be9727691c68912991e14dfe
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
There have been discussions about removing this since it does not seem
to be used much and only creates troubles for boards without defaults,
not to mention that it was configurable on many boards that do not
even feature uart.
It is still possible to configure the baudrate through the Kconfig
option.
Change-Id: I71698d9b188eeac73670b18b757dff5fcea0df41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This board uses the reset defaults for DxxIP and DxxIR.
The datasheet "Intel ® I/O Controller Hub 10 (ICH10) Family"
mistakenly says in the D31IP register that all function have INTB as
default. This is however not true as documented in the reset default
value.
This fixes the DSDT such that the SMBus device gets a route for the
INT C interrupt it uses.
Change-Id: I3dd1308fb7acec86b90ecd9d2079cf9a58702c40
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21442
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TESTED: NGI works on VGA with adapter on DVI-I port
Change-Id: I4bd9d451295d26a3e11ded9863f5d45d42c8fead
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This makes the VGA output on the DVI-I connector usable.
This reuses vendor settings.
Change-Id: Ib8b6bf33816f7e468a09ff5e2008c2cb9f7c0a8b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This mainboard features is an G43 northbridge, ICH10 southbridge and
Winbond W83627dhg SuperI/O. This board is impossible to flash
internally with vendor bios (BIOS region is WP and other regions like
IFD and ME are read only and inaccessible respectively). Due to either
ICH10 or board layout it is also impossible to do ISP, which requires
desoldering flash chip. To make hacking more easy there is an empty
SPI header next to spi flash pads which can be hooked up to a SPI
flash.
What works:
* 2 DDR2 dimms per channel (tested with 1+2G in CH0 and 2+2G in CH1);
* SATA with AHCI
* Integrated GPU with option rom (extracted from a Gigabyte vendor
bios)
* VGA (on DVI) with NGI if patched to use DVI gmbus port for output
* PCI
* Reboot and S3 resume
* Descriptor mode with ME disable straps and ME region absent (no
working gbe in this configuration though)
* USB.
What does not work:
* GBE (probably requires working ME);
* Analog on DVI port out is shaking, which is not the case with vendor
BIOS (setting clockgen on smbus 0x69 like vendor fixes it).
* Booting with ME enabled (needs raminit patches for that)
Not tested:
* Sound;
* All the rest.
Not coreboot related problems:
* Flashing this board with vendor bios is a PITA and requires
desoldering flash chip;
* In situ programming is not possible.
TESTED with SeaBIOS and Linux 4.10.8
Change-Id: If27280feb7cbf0a88f19fe6a63b1f6dbcf9b60f4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
