Age | Commit message (Collapse) | Author |
|
Remove the CNVi Bt PCI config and add Bt flag.
There is no PCI host interface in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS.
Change-Id: I17c3e2761f91fb397d140d1954b6d4b451c4c603
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support to pick the right vbt from cbfs according to
SKU-ID.
Change-Id: I8795cc67d87429eddb31328f1e2a90c346b53533
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the adlrvp mainboard.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic56ebab02e50a466662a07d122d8f40eaf16b54b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I55815a824ea3a77e6e603ba4beb17457f37c48f5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
PCIEXP_HOTPLUG has a prompt and as such is not supposed to be forced.
Just change the default value to 'y'.
Change-Id: Ie4248700f5ab5168bff551b740d347713273763c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
As per CL:2641346, update GBB flag names:
GBB_FLAG_FORCE_DEV_BOOT_LEGACY -> GBB_FLAG_FORCE_DEV_BOOT_ALTFW
GBB_FLAG_DEFAULT_DEV_BOOT_LEGACY -> GBB_FLAG_DEFAULT_DEV_BOOT_ALTFW
BUG=b:179458327
TEST=make clean && make test-abuild
BRANCH=none
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I0ac5c9fde5a175f8844e9006bb18f792923f4f6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Add mainboard Kconfig to Kconfig.name files
2. Handle mainboard names in Kconfig file for adlrvp
3. Created a new devicetree.cb for Adlrvp-m.
3. Add override devicetree for ADL-M RVP.
4. Configure proper PCI and USB ports as per schematics for ADL-M
BUG=None
BRANCH=None
TEST=Able to build ADL-M RVP variants adlrvp_m and adlrvp_m_ext_ec.
Signed-0ff-by: Maulik Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I997b89ba87fb03dfa6a836caec51efd05baa2e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49871
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4f17f9d58d2c07264d7d8e83a6fce832c9304c24
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Assign 7-bit address of the targeted slave SPD.
TEST=Able to read correct SPD data from SMBUS.
Change-Id: If24e61b583638be7c055541c6eb126da28b542f6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=Ensure SMBUS CLK/DATA GPIO is in NF1.
Change-Id: Id615462cc21fc24e7ec6ef16274d784d41bd9bd4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Found using:
diff <(git grep -l '#include <string.h>' -- src/) <(git grep -l 'STRINGIFY\|memcpy\|memmove\|memset\|memcmp\|memchr\|strdup\|strconcat\|strnlen\|strlen\|strchr\|strncpy\|strcpy\|strcmp\|strncmp\|strspn\|strcspn\|strstr\|strtok_r\|strtok\|atol\|strrchr\|skip_atoi\|snprintf' -- src/)|grep '<'
Change-Id: Id2aa085a4762355d9fb1628df40f7b43fbc81fc0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I1112aa4635a3cf3ac1c0a0834317983b4e18135a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I73234da6e77f83c6aeb5c40cf6ffdb3cccc4074c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Refactor PCIE port config structure. Make it easier to map from
schematic. We don't have to convert the PCIE ports RP number and
CLK source in devicetree. All the convert will be done by SoC level.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0b390e43f8e99b19cfad178139b86a2f77d7a57b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Idc11f1e131df2e01864fedac864bda5e11f2d17b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Even the boards with MAINBOARD_HAS_CHROMEOS need to be build-tested
with CHROMEOS=n.
Change-Id: I16fcf62a23dae1b21c77cee275c867f9c1de893b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
As per Hardware Architecture Specification (HAS) ADL-P has 7 CLKSRC
and 10 CLKREQ (7 SRCCLK is internal and 3 SRCCLK from external CLK chip).
ADL-M has 6 SRCCLK and CLKREQ (no external CLK chip).
Change-Id: I7d223c165f819669722cbc80245fa8ec20372352
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50130
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I46af3e789de10ca6951b9e17f286c094c08a477f
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. GPP_E5 => Remove unused GPIOs
2. GPP_H12, GPP_H13 => Program the correct Native Functions for GPIO
Change-Id: I588a8c1153eaa1bf818a081c6c5d18a669017d95
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I4356a8bda71e84afe8c348d366479c5006bf2459
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49796
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CLKSRC6 for RP8 is free-running CLK hence ClkReq is not required.
TEST=Able to detect PCIe SD card over x1 slot.
Change-Id: I550d5be9cc7566708b0b86fcd1da833bc4bc828f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change uses the newly added meminit block driver and updates ADL
SoC and mainboard code accordingly.
BUG=b:172978729
Change-Id: Ibcc4ee685cdd70eac99f12a5b5d79fdbaf2b3cf6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I306f8cd74af62c0cd30f445d20c47f774f122481
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49247
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch preserves MRC training data across FW update.
Change-Id: I6b7273471e4fc9dc25eac80904e012f86a981836
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49681
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HAS_RECOVERY_MRC_CACHE is already part of CHROMEOS hence remove
redundant Kconfig.
Change-Id: Ia55b587d77ca5be2a8ae701a3ab95cfebe8627db
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. GPP_D8, GPP_H23 => Remove unused GPIOs
2. GPP_E18 .. GPP_E22 => Program the correct Native Functions for GPIO
Change-Id: Iedb1f8fbf5f96a9617b72ba1a6419e3fd4e331b4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49260
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable PCIE RP1 to fix DEKEL FW download failed for x4
controller (PEG 0:6:0).
Enable PCIE RP3 to fix HSPHY FW download failed for x8
controller (PEG 0:1:0)
BUG=b:176940923
TEST=No FSP error seen while loading DEKEL, HSPHY FW.
Change-Id: I3cd8cba02a96185803a0c0d442f3d6aa495d2642
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
List of changes:
1. Create new Kconfig MAX_CPU_ROOT_PORTS and MAX_PCH_ROOT_PORTS as per
EDS.
2. Add new chip variable to enable/disable CPU PCIE RPs from mainboards.
3. Rename PcieRpEnable to PchPcieRpEnable.
4. Enable CPU RPs as below in mainboard devicetree.cb
RP1: PEG60 : 0:6:0 : CPU SSD1
RP2: PEG10 : 0:1:0 : x8 CPU Slot
RP3: PEG62 : 0:6:2 : CPU SSD2
Change-Id: I92123450bd7cfb2e70aae8de03053672a7772451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49136
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make GBB_FLAG_DISABLE_EC_SOFTWARE_SYNC depend on VBOOT,
rather than force-select it.
Change-Id: I0ec418d4182865636b6350f1ee151420d8e02c33
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
TEST=Able to build and boot ADLRVP.
Change-Id: I93da53f8835e0eec4cf4e78daab26332fd55d334
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change enables PCIEXP_HOTPLUG to support resource allocation for
TCSS TBT/USB4 ports.
Referred from TGLRVP -> https://review.coreboot.org/c/coreboot/+/41543
Change-Id: I5f883dac0d7e5fa84ad2e1683f84c933a90cea51
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
1. Make CLKSRC -> 7 and CLKREQ -> 6
2. CLK 6 is using free running CLK
3. Make LAN CLK 7 as unused as GbE is disable
TEST=Able to detect PCIE SD card on 0x1 slot.
Change-Id: I7fbde9492a0c59fc76931bfb7c9522d4f208ebb0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48449
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the PMC MUX and CONx devices for adlrvp for
conn2.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I52afbd429750cfa416f4ed93aeb1be590f8c3a5c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48230
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the unused UART_BT_WAKE GPIO as BT is over USB.
Change-Id: I638b4528fa5c4c378a1e8ff7bb88546da1513df2
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I928b4528fa5b4c378a2e8ff7bb88547da1413df2
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48213
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
1. Add 2 ports and 2 endpoints
2. Add support for OVTI5675
WFC Cam is on I2C5 and UFC is on I2C1
BUG=None
BRANCH=None
TEST=Build and Boot adlrvp board and able to capture image
using camera.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I6d2a4fdca99354d1b6977233c70ccd950c99d8a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47497
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure RST and PWR_EN signals for both WFC and UFC
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Ie416da373756b1c73472b8572f87930965a3d6ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47496
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Enable Root Port 8 aka 0:0x1c:7
2. Assign free running clock for RP8
3. Apply W/A to get card detected on x1 slot
- Drive OEB 7:GPP_A7 and OEB 6:GPP_E5 low
TEST=Able to detect PCIe SD card over x1 slot
localhost ~ # dmesg | grep mmc
[ 3.643755] mmc0: SDHCI controller on PCI [0000:02:00.0] using ADMA
[ 3.825201] mmc0: new ultra high speed DDR50 SDHC card at address 17f8
[ 3.835452] mmcblk0: mmc0:17f8 SE16G 14.4 GiB
[ 3.849158] mmcblk0: p1
Change-Id: Ibea37b8de4dd020ff0108ec90ea6f8bcfaa4fb17
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48080
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This patch adds LPDDR5 memory configuration parameters to FSP.
TEST=Able to pass FSP-M MRC training on LPDDR5 RVP.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I787bf97dd6c244bd3b0662e5bd061a2da80baa90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Initialize dq_map array in a single line
2. Make dqs_map array also in a single line
TEST=Able to build and boot ADLRVP LP4 SKU.
Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to pass MRC training on DDR4/5 SKUs
Change-Id: I38fcb17a1be5a8544a17cef8255631b6abef0741
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Configure CTRLCLK and CTRLDATA for HDMI
2. Enable Ddc and HPD for Port-B
3. Disable dual eDP configuration for Port-A and B
TEST=Able to see depthcharge pre-boot screens over HDMI-B port.
Change-Id: I7509b981f35fc60a7885b2b07067cb0d35ec625f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
HPD_1: A19 -> E14
HPD_2: A20 -> A18
Change-Id: Idf3c8f4931bf8364bb9216a9369df7e05dcde047
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Currently the decision of whether or not to use mrc_cache in recovery
mode is made within the individual platforms' drivers (ie: fsp2.0,
fsp1.1, etc.). As this is not platform specific, but uses common
vboot infrastructure, the code can be unified and moved into
mrc_cache. The conditions are as follows:
1. If HAS_RECOVERY_MRC_CACHE, use mrc_cache data (unless retrain
switch is true)
2. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_BOOTBLOCK, this
means that memory training will occur after verified boot,
meaning that mrc_cache will be filled with data from executing
RW code. So in this case, we never want to use the training
data in the mrc_cache for recovery mode.
3. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_ROMSTAGE, this
means that memory training happens before verfied boot, meaning
that the mrc_cache data is generated by RO code, so it is safe
to use for a recovery boot.
4. Any platform that does not use vboot should be unaffected.
Additionally, we have removed the
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN config because the
mrc_cache driver takes care of invalidating the mrc_cache data for
normal mode. If the platform:
1. !HAS_RECOVERY_MRC_CACHE, always invalidate mrc_cache data
2. HAS_RECOVERY_MRC_CACHE, only invalidate if retrain switch is set
BUG=b:150502246
BRANCH=None
TEST=1. run dut-control power_state:rec_force_mrc twice on lazor
ensure that memory retraining happens both times
run dut-control power_state:rec twice on lazor
ensure that memory retraining happens only first time
2. remove HAS_RECOVERY_MRC_CACHE from lazor Kconfig
boot twice to ensure caching of memory training occurred
on each boot.
Change-Id: I3875a7b4a4ba3c1aa8a3c1507b3993036a7155fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
WWAN_RST#: E10 -> F14
WWAN_PWR_EN: E13-> F21
Change-Id: I7182f384eb7a404dfe623c64e29467b41c6b0bdd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The patch replaces if-else-if ladder with switch case for readability
purpose.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I268db8bc63aaf64d4a91c9a44ef5282154b20a53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47054
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the PMC MUX and CONx devices for adlrvp. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I3b5bb73991feb99577c16fea00c381dd0f855769
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
List of changes:
1. Use devicetree.cb from default location
2. Create variant directory for ADL RVP with external EC as
'adlrvp_p_ext_ec'
3. Add initial overridetree.cb for 'adlrvp_p' and 'adlrvp_p_ext_ec'
to override 'devicetree.cb' as applicable.
4. Move all common files between 'adlrvp_p' and 'adlrvp_p_ext_ec'
to mainboard directory
TEST=Build and boot both ADLRVP with onboard and external EC.
Change-Id: I3591e214ed32dc9baaa49b92dff59579f29c7bd6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47335
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch configures GPIO pins to enable DMIC.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I2907737071f7d6b3c88c492d90edf8455d1fa50a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
The patch enables ALC711 Audio codec.
Test=Verified on ADL RVP.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I73f480dad1047cebd7ffc66e0104ff10cacc300b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This patch enables TCSS xDCI, TBT PCIe root ports and DMA controllers
for ADLRVP.
BUG=b:170607415
TEST=Built and booted on ADLRVP.
Change-Id: Iabd6cc7c589d1c20cde9d66c0a63e2cf16316b33
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47288
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch configures the HPD1 and HPD2 GPIO's.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the hotplug
functionality is working.
Change-Id: Ied2d4c56220212a15103e9a2fbd01ce6f0811a74
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch adds DDR5 memory configuration parameters to FSP.
TEST=Able to build and boot ADLRVP with DDR5 memory.
Change-Id: I4711d66c7b4b7b09e15a4d06e28c876ec35bc192
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46485
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
List of changes:
1. Split mem_cfg for DDR4 and LPDDR4 as per board_id
2. Move dq_pins_interleaved into board-specific memory configuration
information
TEST=Able to build and boot DDR4 and LPDDR4 ADLRVP SKUs.
Change-Id: I6ef19209767c810426bba0c8bc48178bf2e2a110
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46873
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
TEST=Build and test booting ADL RVP form NVMe and Optane
localhost ~ # lspci -d :f1a6
Show all the NVMe devices and be really verbose
localhost ~ # lspci -vvvd :f1a6
Print PCIe lane capabilities and configurations for all the NVMe devices.
Change-Id: I0a04b23b17df574d4fa3bae233ca40cd3b104201
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
A regular M.2 NVMe SSD shows up on RP9 and runs at x4 width.
Optane memory module shows up as 2 NVMe devices in x2 config:
- NVMe storage device uses RP9
- NVMe Optane memory uses RP11
Note: These two devices are sharing CLK PINs because of same M.2 slot.
TEST=Build and boot ADL RVP board using Intel Optane card.
Change-Id: Ia21d7d2fd07c4fb32291af7bb5a2e41e40316278
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make PCI ClkReq-to-ClkSrc mapping correct to fix SSD detection issue
on ADL RVP.
TEST=Able to detect WD SSD card over PCH SSD RP9.
Change-Id: I7e26429281f8d3b9edae0f266a5868118369be3f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch programs GPIO for PCH SSD Power Enable (GPP_D16) and Port
Detect (GPP_A12) as per schematics.
TEST=Able to build and boot ADL RVP.
Change-Id: I015e46bdf25437c6b196deb3e610bc1b58726070
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add required ASL files into dsdt.asl
TEST=Dump and disassemble DSDT and verify all ACPI devices are present.
Change-Id: I70829e2bdb12fad20627d9aea47e745d9095f07a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
List of changes:
1. Add devicetree.cb config parameters related to FSP-S UPD
2. Configure GPIO as per ADL-P RVP
3. Add files required for ramstage(ec.c, mainboard.c)
4. Add smihandler.c for SMM
5. Add devicetree changes as below
- USB OC PIN programing
- GPE configuration
- SATA port mapping
- LPSS configuration
- Audio configuration
- IA common SoC configuration
- EDP configuration
- TCSS USB configuration
- Enable S0ix
TEST=Able to boot ADL-P RVP without Chrome EC (using on-board EC) with
UART log over legacy UART0 port as 0x3f8 with NVME at RP9 reach till
depthcharge payload.
Change-Id: I120885956c88babfa09d24ce1079d49306919b8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I6f4d0bf9adc1cce4942a16675a072ffea00bd2e0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
List of changes:
1. Add DDR4 and LPDDR4 memory related code
- SPD for LPDDR4
- DQ byte map
- DQS CPU-DRAM map
- Rcomp resistor
- Rcomp target
2. Fill FSP-M related UPD parameters
3. Add devicetree.cb config parameters related to FSP-M UPD
TEST=Able to build and boot ADL-P RVP till ramstage early
Change-Id: Iffc5c17ed0725f61c8c274a80a1d27161ca6cebf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
List of changes:
1. Initial code block to select SOC_INTEL_ALDERLAKE Kconfig
2. Add minimum code to make ADL-P RVP build successfully
3. Mainly bootblock and verstage code added to reach till verstage
4. Add support for 2 mainboards as ADL-P board with default EC (Windows
SKU) and Chrome EC (Chrome SKU)
5. Add empty dsdt.asl to avoid compilation error
TEST=Able to build and boot ADL-P RVP till romstage early.
Change-Id: I2b551f48a4eb4d621d9a86c5d189c517d5610069
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|