| Age | Commit message (Collapse) | Author |
|---|
|
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
A fully functional bootblock (that can boot into verstage or romstage)
is about 38000 bytes. If self decompression (CONFIG_COMPRESS_BOOTBLOCK)
is enabled, only 25088 (66%) bytes are needed.
Inspired from crosreview.com/1070018.
BUG=b:80501386
TEST=manually flashed into kukui and boots into romstage.
Change-Id: I7a739866a4ea3bcafe2ff7b9e88d5ed00f3f3e40
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/27599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
These values are Intel recommended.
IccMax = 28A
DC and AC LL = 4mOhms
Pl2 = 18w
BUG=b:79666828
BRANCH=none
TEST=Enabled p-states with patch
Change-Id:I82d1516998cc26b789faa5d4e897feb06dc06020 and then
"emerge-nocturne depthcharge coreboot chromeos-bootimage", flash spi
image onto nocturne, boot to kernel and verify device stays alive and
responsive for several minutes without locking up.
Change-Id: I4c67c6a095aecc158e529a6b393baf03ec358a3d
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27175
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables p-states for nocturne which was disabled by commit
de31587a (mb/google/poppy/variants/nocturne: disable p-states). p-states
feature was disabled as a temporary work-around as system was getting
hung while booting up. Now with IMVP7 firmwware turning and hardware
rework the issue is not seen, so its safe to enable p-states.
BUG=b:79666828
BRANCH=none
TEST=cherry picked Change-Id: I4c67c6a095aecc158e529a6b393baf03ec358a3d
patch and then "emerge-nocturne depthcharge coreboot chromeos-bootimage"
, flash spi image onto nocturne, boot to kernel and verify device stays
alive and responsive for several minutes without locking up.
Change-Id: I82d1516998cc26b789faa5d4e897feb06dc06020
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27257
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For unused pins in octopus baseboard, configure them as GPIO input
and use the default termination. For the pins where board has an
external termination, remove SOC's internal termintation.
BUG=b:110654510
Change-Id: I67ec62913b0ef47105289838218f5d74c004223c
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/27183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per the ACPI specification, there are two types of power button
devices:
1. Fixed hardware power button
2. Generic hardware power button
Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
is not set in FADT by the BIOS. This device has its programming model
in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
power button device by default if the power button FADT flag is not
set.
On the other hand, generic hardware power button can be used by
platforms if fixed register space cannot be used for the power button
device. In order to support this, power button device object with HID
PNP0C0C is expected to be added to ACPI tables. Additionally,
POWER_BUTTON flag should be set to indicate the presence of control
method for power button.
Chrome EC mainboards implemented the generic hardware power button in
a broken manner i.e. power button object with HID PNP0C0C is added to
ACPI however none of the boards set POWER_BUTTON flag in FADT. This
results in Linux kernel adding both fixed hardware power button as
well as generic hardware power button to the list of devices present
on the system. Though this is mostly harmless, it is logically
incorrect and can confuse any userspace utilities scanning the ACPI
devices.
This change gets rid of the generic hardware power button from all
google mainboards and relies completely on the fixed hardware power
button.
BUG=b:110913245
TEST=Verified that fixed hardware power button still works correctly
on nautilus.
Change-Id: I733e69affc82ed77aa79c5eca6654aaa531476ca
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Logic: If vboot is not used and the tpm is not initialized in the
romstage makes use of the ramstage driver to initialize the TPM
globally without having setup calls in lower SoC level implementations.
* Add TPM driver in ramstage chip init which calls the tpm_setup
function.
* Purge all occurrences of TPM init code and headers.
* Only compile TIS drivers into ramstage except for vboot usage.
* Remove Google Urara/Rotor TPM support because of missing i2c driver
in ramstage.
Change-Id: I7536c9734732aeaa85ccc7916c12eecb9ca26b2e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24905
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix VBT SSF setting for panel T8/T10 as Akali/Akali360 panel
has T8 minimum 33.3 ms and T10 minimum of 100 ms.
BUG=b:111530392
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test & measure T8/T10 waveform
Change-Id: I642a1aa0b2d13b33e6113f94e73dfc77834766d4
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Coolstar's custom touchpad drivers for Windows require level triggering,
and the Linux drivers don't care/perform identically either way. Set
touchpad interrupt to level trigger, matching change made to other
Chromebooks.
Test: boot Windows 10 on google/chell, verify touchpad functional
Change-Id: Id5f145b8b24c04f9c6661710a0cda95f135293e9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Explicitly enable VMX, as some OSes (eg, Windows) need VMX
feature enabled and locked in order to fully support virtualization
Test: boot Windows 10 on google/chell, verify OS reports virtualization
enabled
Change-Id: I53ff575755a9ca376dbf953db96191c17bf57f5f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/asuka (Dell Chromebook 13 3380) as a variant of
glados Skylake reference board:
- add asuka-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/asuka, verify correct functionality
Change-Id: I591578fea2514a28c75177835807c3f250904577
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27421
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add google/cave (Asus Chromebook Flip C302SA) as a variant of
glados Skylake reference board:
- add cave-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/cave, verify correct functionality
Change-Id: I5c5181ce68f7a24ccd49f53ecd9d48c081fd085a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/caroline (Samsung Chromebook Pro) as a variant of
glados Skylake reference board:
- add caroline-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add caroline-specific memory-init param to romstage
- adjust mainboard EC SCI events for boards with tablet function
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/caroline, verify correct functionality
Change-Id: I611a4e76581ba2e5b42e1bc48b0a5b8c70f3598e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add google/sentry (Lenovo Thinkpad 13 Chromebook) as a variant of
glados Skylake reference board:
- add sentry-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add sentry-specific GPIO determination of which audio codec
is present
Adapted from Chromium branch firmware-glados-7820.B, commit
b0c3efe54d877246d07f2467b2dff51cc30348fa [soc/intel/skylake: Enable VMX]
Test: build/boot google/sentry, verify correct functionality
Change-Id: I783422aedac8b7fc52098eebd05b2061a1011b60
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27418
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the I2c timings to the latest measurements.
BUG=b:72442912
TEST=Boot grunt
Change-Id: I6f9538d26b77ae952ad585e569b3a836e1a09da2
Signed-off-by: Matt Wells <dawells@google.com>
Reviewed-on: https://review.coreboot.org/27553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change adds variant rammus derived from baseboard poppy.
The setting is copied from the poppy and will be modified later
BUG=b:111579386
BRANCH=master
TEST=emerge-rammus coreboot
Change-Id: I169c225e28183a7a93f1142a3bf87a60b26ce9ca
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change provides implementation of smbios_mainboard_sku
that queries the EC for SKU ID using CBI. Currently,
get_board_sku() is implemented as a common function for all
variants since this is the only way used by all the octopus
variants to query SKU ID. If this changes in the future,
this function can be changed to a variant_* callback.
BUG=b:111671163
TEST=Verified following on phaser:
1. "mosys platform sku" returns the SKU ID programmed in CBI
2. "dmidecode -t 1" shows SKU information as "skuXYZ" where XYZ
is the SKU ID programmed in CBI.
Change-Id: Ic0d344b3c13632f2ca582adc36aa337b99959712
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change increases COREBOOT region size by the amount of unused space
left in RO_SECTION. This extra space is useful when building images with
debug enabled.
BUG=b:111661025
Change-Id: Icbd88c3350f96707f37b69fe01f8ae9c7838ab82
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27555
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DW9807 NVM support by adding required ACPI code
BUG:b:110815821
TEST=On Nautilus board, execute "cat /sys/bus/i2c/devices/i2c-INT3499:00/eeprom"
in the terminal and see if there is any data to be dumped.
Change-Id: Ib83fa1a522402a59566e3f55fa5c1af4490266e4
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Reviewed-on: https://review.coreboot.org/27508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
Nautilus-WiFi board doesn't have external pull-up on USB2_OC2# route,then
abnormal over-current is asserted on USB type-A port.
It causes USB type-A port to be blocked, so we need this internal pull-up.
BUG=b:111578984
BRANCH=poppy
TEST=Verified over-current not triggered abnormally on basic sku board
Change-Id: I159f686cef9c8d254f390d7f1dff8011f43fc066
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Convert lars to a variant of glados Skylake reference board:
- add lars-specific DPTF, EC config, GPIO config, Kconfig,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add conditional generation of NHLT ACPI data for Maxim codec,
including override of OEM ID and OEM table ID
- remove existing lars board/directory
Test: build/boot google/lars, verify functionality unchanged
from pre-variant configuration
Change-Id: Iab37f1b92b0f3a5d99796f916a6fdcc14ce4eef4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27413
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert chell to a variant of glados Skylake reference board:
- add chell-specific DPTF, EC config, USB port defs, GPIO config,
NHLT config, PEI data, VBT, SPD data, and devicetree
- add romstage handler to turn on keyboard backlight for boards
so equipped
- remove existing chell board/directory
Test: build/boot google/chell, verify functionality unchanged
from pre-variant configuration
Change-Id: I7dfbafe3afcab7cee7bcb2bf91c6733c07b409c4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Convert Skylake reference board glados to variant setup in
preparation for merge with existing Skylake boards chell and lars,
and upstreaming of new boards asuka, caroline, cave, and sentry.
The following changes have been made:
- move DPTF to variant subdir
- move non-common EC defs to variant subdir
- adjust Kconfig for variant setup
- move non-common NHLT config to variant Kconfig
- make non-common NHLT ACPI code conditional
- move devicetree to variant subdir
- move board GPIO defs to variant subdir
- move board PEI data to variant subdir
- move SPD index calculation to romstage so available for
dual-channel determination during PEI for boards which need it
- move SPD compilation to variant makefile
- add weak function for determination of dual-channel RAM
- add weak function for mainboard_gpio_smi_sleep() so SKL-Y variants
can override and power down rails as needed
Test: build google/glados
Change-Id: I41615979dc11b5a10e32d6b5f477a256735cde53
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the GEO SAR feature for nocturne. OxM programs wifi_sar VPD key in factory.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:65155728
BRANCH=none
TEST= Set the wifi_sar VPD with below command (values are junk for test purpose only,
actual values would be set be OxM)
sudo vpd -f <coreboot.rom> -s wifi_sar=30313233343536373839303132333435363738393030313
24142433435364445463031324142433400364445463031323343444546303132333435
Flash the <coreboot.rom> and boot to kernel. Get ACPI table and WGDS would get created
with VPD values passed in.
Change-Id: I32ad591f15fdb34704c8d98d98646dfa2d8882ff
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Refactor GPIO code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Icdd1f2a1dd1bd64a7218bf9c63bd4a0af1acbcc0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Latest nocturne architecture uses clk src 3 for nvme.
BUG=b:111514174
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify nvme
nocturne devices are able to recognize the nvme controller.
Change-Id: I5b2bf012ba88568cb4b0bb3918a3a2c6770ff4c1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27536
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is based on the Grunt variant.
BUG=b:111607004
TEST=Build Liara
Change-Id: I8f23e972be0d1665c736d61621a0caaa4c4c5551
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This is based on the Grunt variant.
BUG=b:111606874
TEST=Build Aleena
Change-Id: I6fd42db6f9f309c3c375b670cd22f818555e4195
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Observed thermal shutdown initiated by DPTF due to CPU temperature
reaching critical temperature trip value. During stress testing with
busty workloads like Octane, Aquarium on open yorp board with heat sink,
sometime CPU temperature spikes till 99 degree Celsius and DPTF
initiates system shutdown. With reference to previous APL/reef/coral
platforms, this updates 105 degree Celsius for the CPU critical
temperature trip value to avoid shutdown. This patch also updates power
limit1 value to avoid the abrupt thermal shutdown by DPTF.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Icd786d3c9b5f7c733dac3fd3e22579e2434058a6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We should use active-state power management where possible to reduce
power consumption during normal operation. Enable these options.
Linux does not seem to enable this for AMD, and the Intel code in coreboot
does enable these options.
PCIEXP_COMMON_CLOCK is enabled also, to follow how Intel does it.
BUG=b:110041917
TEST=boot on grunt, see that WiFi and eMMC still run OK
Change-Id: Ia7c711304ffe460a9fb0d4f654a51485958239ea
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27464
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This creates a meep variant for octopus.
The devicetree overrides are copied from yorp, otherwise everything
just defaults to baseboard settings.
BUG=b:111543000
TEST=None
Change-Id: I791f8d1589d7323fbe884dddf0f9d7362a41b9ac
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Atlas has one sensor, create a single endpoint to CIO2. Create power
resource for enabling/disabling camera.
BUG=b:111141128
Branch=None
TEST=Testing on Atlas board
Change-Id: Ide0e923bbc34f869dd0227c0a29977645bc5d58d
Signed-off-by: Ping-Chung Chen <ping-chung.chen@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/27350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
Keep the backlight off until it is needed.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen, not prior.
Change-Id: Ia1aba787734e2976146ecd305dd821f0b326f0db
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:72694972
TEST=Backlight turns on ChromeOS resume
Change-Id: I452e2ea94b508b137cf52301df5d2d1ad5c9ab70
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27488
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the backlight in the OS callback to SMI for APMC. This keeps
the backlight off until the OS is ready to display something.
BUG=b:72694972
TEST=Backlight turns on at ChromeOS splash screen
Change-Id: Idf32b1a3d45971883571a829a5c0c1f8563bb1f7
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the mainboard resume function and __weak variant override.
Change-Id: I808734208bd1ce81428771ea203709b53db56cd3
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
there are 3 thermal sensors and index is:
0: 1 Charger
1: 1 SOC
2: 0 CPU
it needs to adjust sensor to index 2 to have correct
CPU temperature.
BUG=b:111284412
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I27afb6c5b64b0c39d6db15e6c61ea16a1fda1ca3
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This device claims to run at 75MHz with dual read, but it is not always
reliable. Add an option to change the SPI flash speed to 16MHz, to avoid
any problems.
BUG=b:111363976
TEST=manually try to get my em100 running (it doesn't yet)
Change-Id: I78d3d32c467aac82c72d31c773bfb0f69808aed4
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This applied to AMD devices as well as Intel, although the mechanism is
different. Move the option to a common place.
BUG=b:111363976
TEST=USE=em100-mode emerge-reef coreboot
See that a message appears:
* Enabling em100 mode (slow SPI flash)
Change-Id: Iea437bdf42e7bc49b1d28c812bfc6128e3eb68bd
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111195311
TEST=Build grunt, verify SPDs are present
Change-Id: Ief5ed5c3ca1d96b36926f1fc84c344a8d66dcda5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Currently thermal event support can not be disabled at board level.
Define and dependent code are placed in same file.
Move define of HAVE_THERM_EVENT_HANDLER to mainboard file.
Change-Id: Icb532e5bc7fd171ee2921f9a4b9b2150ba9f05c5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/27415
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables tablet mode ACPI device for yorp.
BUG=b:111264961
CQ-DEPEND=CL:1132686
Change-Id: I81140b84a1adb5b21f1656fd89d953331e538f01
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Enabling of TBMC device on AP side requires corresponding support on the
EC side as well. Since not all octopus variants have tablet mode support
enabled, this change enables TBMC device only for phaser.
BUG=b:111264961
Change-Id: I1ce181baa8ebaff0a9d767e97ddc256eef9789e8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change enables EC SW sync for bip by removing GBB flag selection
for disabling SW sync.
BUG=b:110523189
TEST=Verified that EC SW sync works fine on bip.
Change-Id: Iff8ee67fd682530a4fa82643cd1d00a645b347a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to get better performance, map dram as cached after dram ready
in romstage.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui. Need a futher check after dram
calibration code ready.
Change-Id: Ie541fe08ee1d5b260abbabc0a5c18fb04e602b9c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27304
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor MMU operation code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Id8173da0a02e57e863263fcd89c91a9c089e8a0f
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add an extra space after 8th value on each line to make it easier
to count the values.
Update the empty spd to remove two random 0x80 values.
BUG=None
TEST=None
Change-Id: If330dbf0c133f65aedddc58ecb351a80b0e45a05
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27423
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111079089, b:80375243
TEST=Build grunt, verify that SPDs are included.
Change-Id: Idb03a3fa0842f7f89bb8c66dedbb8a0b293569be
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/27422
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
change I2C irq to EDGE trigger
BUG=b:110962003
BRANCH=master
TEST=emerge-grunt coreboot
Raydium TS is working.
Change-Id: Iff3acf4199d23b29dff209ec1c03a731679c6cbe
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27327
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures ACPI to properly route notifications from the EC
for tablet mode events to userspace. Relevant EC config changes are at:
https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/1125261
BUG=b:111078678
TEST=With EC change, tablet mode detected by evtest and powerd
Change-Id: Ifbc318186b195534f647f062544de4968aa87401
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I85cd567a923cccd2504f351aae276b5f0d9db4de
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Delco <delco@google.com>
Reviewed-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To make image sensor working, the intended power sequence need to
applied.
BUG=NONE
TEST=NONE
Change-Id: I4833c0e303174b297c1d193495e08e55d294a717
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use lower case for hex values.
BUG=b:74363445
TEST=compile
Change-Id: I24afea58b1a791fac3c87ad397a696f7f6e0d127
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27264
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to sona thermal table, PL2 need to check cpu id.
And then set PL2 value.
BUG=b:110867809
TEST=The thermal team verify OK
Change-Id: I5759fb3c685e3d4eef1be054541f950843d19874
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
nayna/NT6CL256T32CM-H1 file change byte 145/146 to be"20" for JEDEC spec
BUG=b:79443146,b:109708239
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test on R69.10825 with mosys
Change-Id: Iadc820111f0aed34e5b46d7e23dff44cb5bb811d
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27275
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit changes the uid and desc fields for the sx9310 entries
in the devicetree to be unique, and correctly identify the position
of the respective sensors.
Change-Id: I501df7d3349fdebc9673c9815f5b1b2458abac6e
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
|
|
Change-Id: I4f82482595b0e6c6159c6e1c66158bc18b061f04
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We would use GPP_B20 instead of board id to determine nautilus SKU.
BUG=b:80052672
BRANCH=poppy
TEST=Verified the new coreboot could determine SKU correctly
Change-Id: I1978b544eef7a184a3da191306ee32d862fa8c36
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27220
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This creates a bobba variant for octopus.
The devicetree overrides are copied from fleex, otherwise everything
just defaults to baseboard settings.
BUG=b:110781720
TEST=None
Change-Id: Ic30c6b0d955ce26f4a9f40cd7fef1c429ab950fc
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27223
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates TSR sensor info with appropriate names.
Also, updates Charger effect with correct TSR sensor mapping.
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board.
Change-Id: Ia3bbc78f8d823e88a91265e0d55c5ac2a4ea31a9
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
These files are directly extracted from the vendor firmware
Change-Id: I1f05c913872c5d2d8c8279d89eac52fd4bf4e35e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
TPM config items added upstream before ready
SPI/TPM is not functional on Cheza yet
Change-Id: I302e00014dc31279fe2574765763ecdbf326b449
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/27213
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds GSMI callback elog_gsmi_cb_mainboard_log_wake_source
to enable logging of EC wake events in S0ix.
BUG=b:79449585
TEST=Verified that S0ix entry/exit events are added to eventlog:
=========== Lid open ================
62 | 2018-06-25 14:02:36 | S0ix Enter
63 | 2018-06-25 14:02:56 | S0ix Exit
64 | 2018-06-25 14:03:26 | Wake Source | GPE # | 15
65 | 2018-06-25 14:03:32 | Wake Source | GPE # | 65
66 | 2018-06-25 14:03:37 | EC Event | Lid Open
Change-Id: Icc8cd3624966ff66d2cf189871e452cf650cec40
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27235
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put the PCIe clock pins in power-saving mode for the BayHub eMMC bridge to
save power. This requires use of an additional register (Misc control
register 2) and another bit in the existing 'protect' register. The naming
of bit 0 of that register is incorrect, based on the latest datasheet
(14 June 2018) so fix that too.
BUG=b:73726008
BRANCH=none
TEST=boot without this patch:
iotools mem_read32 0xfed80e00
0x0046ffff
With this patch:
$ iotools mem_read32 0xfed80e00
0x00463fff
Also see that the PCIe clock stops when eMMC is idle and can be started by
starting disk activity.
Change-Id: I5ad1467b2e2e151215d2dfd2ce48cd4a451fe480
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/26515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that sconfig is able to support variant-specific override trees,
this change updates octopus boards to use this feature. Following
devices are moved from baseboard devicetree to variant specific
devicetree:
1. Touchscreen
2. Trackpad
3. Digitizer
4. Audio codec
BUG=b:80081934
TEST=Verified that the right devices show up in static.c for each
variant.
Change-Id: I8df0cdf4dbcd7613aa4ef4042c272eca2915da9e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27219
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We found GPP_C3 keeps high when system in S0ix mode. It caused 1.8V
leakage. To fix this problem, add GPP_C3 into config for Pantheon
Synaptics touchscreen.
BUG=b:78436458
BRANCH=None
TEST=Let DUT in S0ix mode and check GPP_C3 is normal.
Change-Id: Idb2dab93178af1dae54265e49522b473b69a35af
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates DPTF parameters for Octopus baseboard.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I1456b7b9ee9e02491c66b0709c710e1a7ec08cc5
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables xDCI controller on nami.
BUG=b:110443736
BRANCH=None
TEST=None
Change-Id: Ieb63e0d65ac1a142c151a3f93afe306b80a5d99a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/27181
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- add K4E6E304EC-EGCF and K4EBE304EC-EGCF to memory strapping table
BUG=b:110498646
BRANCH=none
TEST=none
Change-Id: Iddacdf1e1d0e2bae0c6168c86e54f5f602cd9d19
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27184
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configures a GPIO pin for enabling/disabling bluetooth on the
next version of the atlas board. The default is for bluetooth to be
enabled at this point.
BUG=b:110614620,b:110613353
BRANCH=none
TEST=none
Change-Id: I4ba940e89b1dc03548b7ab44b8f84dc9a3097acb
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify DPTF TRT parameters to solve thermal sensor QT2 PSV problem.
BUG=b:109941652
TEST=The thermal team verify OK
Change-Id: Id9d39d8282712a0341fea10f74c0e40bb1ac9d7c
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move GBB_FLAG_DISABLE_EC_SOFTWARE_SYNC under each variant config and
select it for bip and fleex only.
Functional change in this CL is that EC SW sync will be enabled for
phaser.
BUG=b:110523400
Change-Id: If6f37c6b2ee71130b9ed5b10ce92fb23fa1c39fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I7358ee34df873098a86d692cc8a909b0ec5023a8
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the end it does not look like RCBA register offsets are fully
compatible over southbridges.
This reverts commit d2d2aef6a3222af909183fb96dc7bc908fac3cd4.
Is squashed with revert of "sb/intel/common: Fix conflicting OIC
register definition" 8aaa00401b68e5c5b6c07b0984e3e7c3027e3c2f.
Change-Id: Icbf4db8590e60573c8c11385835e0231cf8d63e6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Upstreaming Chromium commit 0bc6c43:
Lili: Update Memory IDs
TEST=Build and boot up on lili board
Original-Change-Id: I6da1e97820b1bf2e751102384eed07236143fe2b
Original-Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/956782
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: Icf6588582da3b4a7861bced539d51a914b011dc4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27135
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- add K4E6E304EC-EGCF and K4EBE304EC-EGCF to memory strapping table
- add SPD files for K4E6E304EC-EGCF and K4EBE304EC-EGCF
BUG=b:110277021
BRANCH=none
TEST=none
Change-Id: If1322311bd91842d6d32725822d91fd6d9e8077c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When played Left Only Audio and Right Only Audio, we observed that Audio
got swapped. Left Data played on Right Speaker and Viceversa.
This patch fixes the above issue.
BUG=b:73635449
TEST=Play Left only & Right only Audio and cross check Audio.
Change-Id: Ie9c417ad0634a76fc8a4126ee75886603f1b3da0
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27167
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set register speed_shift_enable=0 in devicetree to disable
p-states in coreboot as a temporary workaround for an SoC hang.
BUG=b:79666828
BRANCH=none
TEST="emerge-nocturne depthcharge coreboot chromeos-bootimage",
flash spi image onto nocturne, boot to kernel and verify device
stays alive and responsive for several minutes without locking up.
Change-Id: I71ed4c80c109b28ffa85d48338ce3a62396d272e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is a temporary hack to test camera presence before we have full
camera support implemented. Basically, we can now probe the camera
over i2c to verify that it's connected and the camera LED turns on.
BUG=b:80106316
BRANCH=none
TEST=camera LED comes on and camera can be probed over i2c.
Change-Id: Ibaabf6c6f6a1dabaddd2fc47c820e090ca5984a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27128
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the necessary config to enable touchscreen sensor in linux.
BUG=b:110286344,b:110286345
BRANCH=none
TEST=verified touch functionality using eval board
Change-Id: I21efafda3f2ae1dcea19e44f8d66f6dfaac1bb12
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We plan to use i2c-hid compatible trackpads on atlas, so this switches
the trackpad config to i2c-hid.
BUG=b:80662079
BRANCH=none
TEST=used trackpad to verify motion tracking
Change-Id: I2702e61a6aa96250c0c09ea4bd15d0c671eedadc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27126
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change defines SAR sensor device into devicetree.cb.
Since only LTE sku has SAR sensor, we will use GPP_B20 as a device_present_gpio.
BUG=None
BRANCH=poppy
TEST=Verified SAR sensor device is loaded by driver in Chrome OS
Change-Id: Ib4969e4b82d18b1b1a599de8226c2d7d4bda7915
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27149
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nautilus 2nd SKU has a leakage voltage at GPP_D0 in S5 state. We need to set this to LOW when entering S5 for clear the leakage.
BUG=None
BRANCH=poppy
TEST=Verified the leakage is gone after update coreboot
Change-Id: I054e707b2bc2e63d6f99cd2fd8a57be20615f111
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For supporting new SKU, we need to override GPIO table and device configuration.
The board ID of 2nd SKU of nautilus is started from 9, so we would determine SKU with it.
BUG=b:80052672
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7242f23f47010664cc29ea86a126e63c9dd62ccd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27147
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change fixes the following issues with EC_IN_RW signal:
1. EC_IN_RW is an input signal to the SoC. Configure it accordingly in
GPIO table for baseboard and bip.
2. GPIO_EC_IN_RW is passed in coreboot tables so that payload can
re-sample the GPIO at runtime.
BUG=b:110084012
TEST=Verified that EC_IN_RW signal is read correctly in depthcharge.
Change-Id: I1c5f5b4b914ced98e89a571dc398df5ba1fe8460
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change adds Synaptics device to phaser project.
BUG=b:110236590
TEST=emerge-octopus coreboot chromeos-bootimage
reflash the coreboot to DUT,make sure the Synaptics Touchpad can work.
Change-Id: Icc1e8c35a9de54ed04187fcf219a72a592d3bd81
Signed-off-by: Xingyu <wuxy@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27159
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to schematic, we need to correct USB OC pin configuration.
- OC0 for Type-C Port 1
- OC1 for Type-C Port 0
- OC2 for Type-A Port
- OC3 to NC
BUG=NONE
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ic71baef646926cc6aadcc5dda7cb14f00e8d3687
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds ACPI properties for SYTS7817 device.
BUG=b:110013532
Change-Id: Ifdec4efce169c066f212a393df21089d43d8e4d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This creates a fleex variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:110085182
TEST=None
Change-Id: Ia8b8bb757f67bea997b7f43489c38cac62f7682d
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/27105
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All Grunt variants should identify as grunt in SMBIOS so that
they're recognized correctly as a unibuild Grunt variant.
BUG=b:110244268
TEST=Careena identifies as grunt
Change-Id: Iaf254149fbec9551d9220018d6d6a0a1be741538
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/27117
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This pin does not have a native function for eSPI. Nonetheless if we use
eSPI, it should be configured as a GPIO and kept unconnected to allow
S0ix entry.
Also removed initialization of LPC pins in mainboard code as they are
already initialized in chipset code. The settings fpr LPC pins in
chipset code were updated to those that were previously in mainboard
code and have been validated on LPC flavor of Geminilake RVP.
BUG=b:79251613
BRANCH=none
TEST=From kernel prompt in bip, type powerd_dbus_suspend.
Check on EC console that SOC enters S0ix.
Change-Id: Ie0c1013fee638a3b7a91469736efc0c25a1597fa
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/23742
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
