summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2024-01-10soc/mediatek: Add common implementation to configure displayYidi Lin
The sequences of configure_display() are similar on MediaTek platforms. The sequences usually involve following steps: 1. Setup mtcmos for display hardware block. - mtcmos_display_power_on() - mtcmos_protect_display_bus() 2. Configure backlight pins 3. Power on the panel - It also powers on the bridge in MIPI DSI to eDP case. 4. General initialization for DDP(display data path) 5. Initialize eDP/MIPI DSI accordingly, - For eDP path, it calls mtk_edp_init() to get edid from the panel and initializes eDP driver. - For MIPI DSI path, the edid is retrieved either from the bridge or from CBFS (the serializable data), and then initializes DSI driver. 6. Set framebuffer bits per pixel 7. Setup DDP mode 8. Setup panel orientation This patch extracts geralt/display.c to mediatek/common/display.c and refactors `struct panel_description` to generalize the display init sequences. configure_display() is also renamed to mtk_display_init(). TEST=check FW screen on geralt. Change-Id: I403bba8a826de5f3fb2ea96a5403725ff194164f Signed-off-by: Yidi Lin <yidilin@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79776 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-09mb/google/brox: Fix error in DDR DQS configShelley Chen
The DQS mapping for DIMM idx 6 was discovered to be incorrect to what was in the schematics. Correcting the mistake in this CL. BUG=b:311450057,b:300690448 BRANCH=None TEST=tested on device and it passed memory training Change-Id: I21f50e2f5b4fae09725c1c7532636ed1cc1a9043 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79843 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2024-01-08mb/google/nissa/var/craaskov: Implement touchscreen power sequencingrex_chou
For brya variants with a touchscreen, drive the enable GPIO high starting in romstage while holding in reset, then disable the reset GPIO in ramstage (done in the baseboard). BUG=b:317746281 TEST=emerge-nissa coreboot chromeos-bootimage Change-Id: I3ca2e2d12a86eaae9e37870a2541c0287e354690 Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79764 Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2024-01-04soc/amd/picasso/acpi: move SoC-common code from dsdt.asl to soc.aslFelix Held
To avoid code duplication and to also bring the mainboards using the Picasso SoC more in line with Cezanne and newer, factor out the SoC- specific code from the mainboard's dsdt.asl files to the SoC's soc.asl. TEST=Timeless builds result in identical images for Bilby, Mandolin, and Zork/Morphius Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Id4ed3a3d3cb55c8b3b474c66a7c1700e24fe908e Reviewed-on: https://review.coreboot.org/c/coreboot/+/79653 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
2024-01-03mb/google/rex/var/screebo: Prevent camera LED blinking during bootJason Chen
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips initial probe during kernel boot, preventing privacy LED blink. BUG=b:317434358 TEST=none Change-Id: I43044e64c2c3a645ec0cad2ac903cc19ac89c9af Signed-off-by: Jason Chen <jason.z.chen@intel.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79803 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
2024-01-02mb/google/fizz: Make use of chipset devicetreeFelix Singer
Use the references from the chipset devicetree as this makes the comments superfluous and remove devices which are turned off. Built all variants with BUILD_TIMELESS=1 and the resulting binaries remain the same. Change-Id: I7752819091e2a75c8d818f7d0cf90eabc11c4759 Signed-off-by: Felix Singer <felixsinger@posteo.net> Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79327 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
2024-01-02mb/google/rex/var/karis: Enhance CNVi and PCIe switchingTyler Wang
1. Set PCIe related GPIOs to NC if fw_config use "WIFI_CNVI". 2. Set CNVi related GPIOs to NC if fw_config use "WIFI_PCIE". 3. Remove "ALC5650_NO_AMP_I2S" case in fw_config_gpio_padbased_override(). bt_i2s_enable_pads should not relevant to audio codec/amp, and it is already enabled in "WIFI_CNVI" case. BUG=b:312099281 TEST=Build and test on karis Change-Id: Ib1a32f1a38ae33cf992b80a3408aa8e2fa3ddab0 Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79765 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-31mb/google/nissa/var/craask: Add ILTK touchscreenRen Kuo
Add touchscreen ILTK for craaskwell. Refer to ILI2901A-A200 Data Sheet_V1.1_20231026. BUG=b:308873706 TEST=build and check touchscreen function on craask Change-Id: I6a68855b1659ff0c9cd33a0ec9acbd289f525a3d Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79735 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
2023-12-31mb/google/dedede: Create dita variantSheng-Liang Pan
Create the dita variant of the taranza project by copying the files to a new directory named for the variant. BUG=b:317292413 BRANCH=dedede TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_DITA Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> Change-Id: I843e33f30cd356e4f12330bdfe2d53a0b3920ef3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79655 Reviewed-by: Derek Huang <derekhuang@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
2023-12-28mb/google/nissa/var/anraggar: add hook for WiFi SAR tablecengjianeng
As a preparation for WiFi SAR table addition, adding hook for it. BRANCH=nissa BUG=b:315418153 TEST=emerge-nissa coreboot Cq-Depend: chrome-internal:6790137 Change-Id: Idb200699bb8c8581b9512ec8ec9442f65f8822b3 Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79730 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-28mb/google/brox: Add new GFX devicesShelley Chen
Add GFX devices for DDI (eDP and HDMI) and TCP (USC C0 and C2 ports). Copied the PLD placements from USB PLDs. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: Ic39916819f64ede1c80eccfd05ba4916b9f285af Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79731 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-12-26mb/google/myst: Update DXIO descriptor definitionJon Murphy
Update definition to be more intuitive and extensible. Port descriptors will be defined as individual entities and added to the descriptor list as such. BUG=b:281059446 TEST=builds Change-Id: I23ddd11b7e4da35a0d81299aa648f928e81ea24e Signed-off-by: Jon Murphy <jpmurphy@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79626 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Tim Van Patten <timvp@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-26mb/google/skyrim: Update DXIO descriptor definitionJon Murphy
Update definition to be more intuitive and extensible. Port descriptors will be defined as individual entities and added to the descriptor list as such. BUG=b:281059446 TEST=builds Change-Id: Ic5a06a7d1bdb9123a0a242a571f094ac3233d7b2 Signed-off-by: Jon Murphy <jpmurphy@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79627 Reviewed-by: Tim Van Patten <timvp@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-26mb/google/zork/dsdt: move LIDS object right after dsdt_top.aslFelix Held
This is a preparation to make the next patch result in identical images for timeless builds and also aligns Zork's DSDT more with Guybrush's DSDT. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I46835b404be13f150c68680afb3fcc78639e08f9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79652 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-23mb/google/rex/var/screebo: Update DTT settings for thermal controlKun Liu
update DTT settings for thermal control,the values before Sensor1 and Sensor2 were set too high. Modify the protection temperature to better meet DUT requirements. BUG=b:291217859 BRANCH=none TEST=emerge-rex coreboot Change-Id: I8abc866c0d05a2437c34198e6b8fb4a58c1cb829 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79683 Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-22mb/google/rex/var/karis: Adjust touchscreen power-on sequenceTyler Wang
According to datasheet, EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high should over 5ms. And current measure result is 200us. Set EN_TCHSCR_PWR to output high in bootblock to make it meet datasheet requirment. Measurement result of EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high: Power on --> 31.7 ms Resume --> 38.7 ms BUG=b:314245238 TEST=Measure the sequence Change-Id: I56e455a980b465f27794b30df058ec0944befc2e Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79571 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-22mb/google/nissa/var/gothrax: Add probe for Type-C Port C1 (DB)Yunlong Jia
Add probe DB_C_A_LTE/DB_C_A for Type-C Port C1 (daughter board). DB_A is only used for skus without Type-C Port C1. BUG=b:316048649 TEST=emerge-nissa coreboot Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com> Change-Id: Ifb702c497740953144b43c56653da16fade1053f Reviewed-on: https://review.coreboot.org/c/coreboot/+/79629 Reviewed-by: Kyle Lin <kylelinck@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Derek Huang <derekhuang@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-22mb/google/brox: Fix config errors with 8 GPIOsShelley Chen
Some GPIOs were not configured correctly according to the HW spreadsheet provided by the HW team. * GPP_B5/GPP_B6 use NF1, not NF2 * GPP_B23 should use NF2, no GPI * GPP_D11 should be set to NC * GPP_E21/22 should be using NF (previous NC) * GPP_F17 is a GPO * GPP_F18 should be an interrupt, not a NF BUG=b:300690448,b:316180020 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I9e1e62adb79bd7fdab935afdbf2d23f9061b88aa Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79705 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-22mb/google/brox: Align GPIO reset with HW spreadsheetShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes in this CL are to fix the pad's reset field as needed. See "Intel SoCs" section in https://doc.coreboot.org/getting_started/gpio.html for reset definitions. BUG=b:300690448,b:316180020 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I4285136184c648adb9dc97748bd6b01cba3f8ddd Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79579 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-12-22mb/google/brox: Fix pulls as necessaryShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes in this CL include fixing the pulls for GPIOs as necessary, making sure that it matches what is in the HW team's spreadsheet. BUG=b:300690448 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: Ie50cb3c6fc85f1633c1afd1330c0e040e04b0ec1 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79704 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-22mb/google/brox: Change unused GPIOs to NCShelley Chen
Did a pass through HW team's brox speadsheet and aligned the gpio.c file with it. The changes here include changing the pad config to NC because it is not being used in ChromeOS. BUG=b:300690448 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I15471e4d7ff25c858b05ef024f15ca7c0b9e598e Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79703 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-21mb/google/rex/var/karis: Add HDMI/eDP GPIOs to early GPIO listTyler Wang
Add HDMI GPIO configuration to early GPIO list to support VGA text o/p in Pre-RAM stage on HDMI. BUG=b:316982707 TEST=Erase MRC cache and reboot, SOL text display on HDMI/eDP Change-Id: Idb2af56baeb4d0ef9db5fc1c5dbcebecee6515e6 Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79572 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
2023-12-21mb/google/rex/var/screebo: Remove Camera EEPROM off timingWentao Qin
Since the camera sensor and camera eeprom share GPP_A12, remove the off timing to avoid issue of camera sensor loss, but this will increase system power by 5mW. (Before root cause, this is a short term workaround to unblock function test.) BUG=b:298126852 TEST=1. Run coldreboot/warmreboot check see if the camera sensor lost. 2. Run S0ix check to see if the camera function abnormal. Change-Id: I49b6ecbfbf3dddd6575bdaaf9c8fd0ee6c09af25 Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79647 Reviewed-by: Jason Z Chen <jason.z.chen@intel.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
2023-12-21mb/google/rex/var/screebo: Configure slew rate to 1/8 for GT domainKun Liu
set slew rate to 1/8 for GT domain. BUG=b:312405633 BRANCH=none TEST=Able to build and boot google/screebo Change-Id: Ib5cb07b7effc4a51c2119183010a03e026f639f8 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79628 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
2023-12-21mb/google/{brya,brox,rex}: Update ec_sync wake capabilityMark Hasemeyer
Some of the boards use the EC_SYNC pin to wake the AP but do not advertise the pin as wake capable in the CREC _CRS resource. Relevant boards were determined through empirical testing and inspection of gpio configuration. Update the ACPI tables for rex, brya, and brox based boards to advertise their EC_SYNC pin as wake capable. BUG=b:243700486 TEST=-Dump ACPI and verify ExclusiveAndWake share type is set when EC_SYNC_IRQ_WAKE_CAPABLE is defined -Wake Aviko via keypress and verify chromeos-ec as wake source -Wake Screebo via lid open and verify chromeos-ec as wake source Change-Id: I5828be7c9420cab6ae838272c8301c302a3e078c Signed-off-by: Mark Hasemeyer <markhas@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79374 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-20mb/google/brox: Enable FSP UPD LpDdrDqDqsReTrainingIvy Jian
FSP default value for LpDdrDqDqsReTraining is 1. For boards that didn't set LpDdrDqDqsReTraining to any value, 0 was being assigned and it caused black screen issue. BUG=b:311450057 BRANCH=NONE TEST=emerge-brox coreboot Change-Id: I4a009076e50408a4f7ff16ddc96a0f2e47b09470 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79646 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-20mb/google/rex/variants/deku: correct GPIO configurationEran Mitrani
GPP_B02 and GPP_B03 were set incorrectly previously. This CL corrects these settings according to schematics. BUG=b:305793886 TEST=Built FW image correctly. Signed-off-by: Eran Mitrani <mitrani@google.com> Change-Id: Id62f15f7a77ac43c72cc6b2645816d6c87133a0e Reviewed-on: https://review.coreboot.org/c/coreboot/+/79457 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-20mb/google/rex/var/karis: Add PANEL_PWRSEQ_EC_CONTROL in fw_configTyler Wang
Only EC will use field "PANEL_PWRSEQ_EC_CONTROL". Add this field in coreboot for align fw_config settings. BUG=b:314245238 TEST=emerge coreboot pass Change-Id: Icecb44a338ddc28027e362332c6a69cc9fd268d5 Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79570 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: YH Lin <yueherngl@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-20mb/google/rex/var/karis: Update fw_config FAN fieldTyler Wang
After confirm with thermal, only EC will reference FAN field in fw_config. Update the settings for align fw_config. BUG=b:307822225 TEST=emerge coreboot pass Change-Id: Id7c4cdba29c5500c06d0f2293495650bb14b9e9c Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79573 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jakub Czapiga <czapiga@google.com> Reviewed-by: YH Lin <yueherngl@google.com> Reviewed-by: Eran Mitrani <mitrani@google.com>
2023-12-20mainboard: Use same indent levels for switch/caseFelix Singer
Use same indent levels for switch/case in order to comply with the linter. Change-Id: I602cf024ec84b15b783d36014c725826f9d6595e Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79418 Reviewed-by: Alexander Couzens <lynxis@fe80.eu> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-20mb/google/rex/var/screebo: Configure Acoustic noise mitigationSubrata Banik
Enable Acoustic noise mitigation for google/screebo and set slew rate to 1/8 for IA domain and ignore the slew rate for SA domain. BUG=b:312405633, TEST=Able to build and boot google/screebo. Before: [SPEW ] AcousticNoiseMitigation : 0x0 [SPEW ] FastPkgCRampDisable for Index = 0 : 0x0 [SPEW ] SlowSlewRate for Index = 0 : 0x0 After: [SPEW ] AcousticNoiseMitigation : 0x1 [SPEW ] FastPkgCRampDisable for Index = 0 : 0x1 [SPEW ] SlowSlewRate for Index = 0 : 0x2 Change-Id: Ib86939ab48c2c6e7d0491d7c1cb4a2c7c6a1b568 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79323 Reviewed-by: Kapil Porwal <kapilporwal@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: YH Lin <yueherngl@google.com>
2023-12-20treewide: Use show_notices target for warningsMartin Roth
This updates all warnings currently being printed under the files_added and build_complete targets to the show_notices target. Signed-off-by: Martin Roth <gaumless@gmail.com> Change-Id: Ia14d790dd377f2892f047059b6d24e5b5c5ea823 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79423 Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-19mb/google/rex/var/screebo: Add delay 1ms after Main 3V3Kun Liu
when S0ix returns S0, PERST needs to delay until Main 3V3 is stable and then pull up BUG=b:313976507 TEST=emerge-rex coreboot,measurement waveform verify pass Change-Id: I33a86e52fab3c5c8cba6ebed0cbdd1b88b6538b0 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79320 Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-19mb/google/nissa/var/anraggar: Use GPP_D15 to control AVDD and AFVDDWeimin Wu
For EVT SCH: 1. Use GPP_D15 to control AVDD and AFVDD simultaneously for MIPI Camera. 2. Delay reset for 5ms when device power on. BUG=b:312663347 TEST=1. Google Camera app working 2. Passed EA verified Change-Id: I880fb309fcef006090e2849fa6c3a0d472851851 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79623 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-19mb/google/hatch/var/jinlon: Increase reset deassert delay to 4 msEran Mitrani
With 1ms delay, reset is de-asserted too soon, before power is fully up, causing a glitch to the reset signal. The issue is resolved with 4ms delay. TEST=tested on google/jinlon device and observed the issue is resolved. BUG=b:260253945 Signed-off-by: Eran Mitrani <mitrani@google.com> Change-Id: I4efe916824cc193a7c2db7599b37f0d4de40bfce Reviewed-on: https://review.coreboot.org/c/coreboot/+/79474 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Shelley Chen <shchen@google.com>
2023-12-18mb/google/rex/var/karis: Enable audio BT offloadTyler Wang
BUG=b:312099281 TEST=Build and boot to Karis. Verify the config from serial logs. w/o this CL - ``` [SPEW ] ------------------ CNVi Config ------------------ [SPEW ] CNVi Mode = 1 [SPEW ] Wi-Fi Core = 1 [SPEW ] BT Core = 1 [SPEW ] BT Audio Offload = 0 [SPEW ] BT Interface = 1 ``` w/ this CL - ``` [SPEW ] ------------------ CNVi Config ------------------ [SPEW ] CNVi Mode = 1 [SPEW ] Wi-Fi Core = 1 [SPEW ] BT Core = 1 [SPEW ] BT Audio Offload = 1 [SPEW ] BT Interface = 1 ``` Change-Id: Icd2c42261fdcfa5aac17be28fde3804348ddf9b4 Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79210 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-17mb/google/nissa/var/anraggar: Disable SDCard controllerWeimin Wu
1. Anraggar doesn't support SDCard, so disable SDCard contorller. 2. Not disabling it will cause can't enter S0ix on first suspend. BUG=b:313585586 TEST=1. check lspci 2. can enter S0ix on first suspend Change-Id: Ie4747d9c5d6ae93d29ef78b629855e0dd320c4db Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79586 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-17mb/google/skyrim: Add and use APCB configuration dataMatt DeVillier
This file is identical to the copy currently found in the blobs repository; it is simply being relocated for consistency and since it does not need to be in an external repo. BUG=none TEST=build/boot skyrim Change-Id: I352f58e0d3965356f3282a2653c6c11b44853857 Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79593 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
2023-12-17mb/google/guybrush: Add and use APCB configuration dataMatt DeVillier
This file is identical to the copy currently found in the blobs repository; it is simply being relocated for consistency and since it does not need to be in an external repo. BUG=none TEST=build/boot guybrush Change-Id: Ice4cbaccca13e9c4ae246fdcde5c89aa2086f1e1 Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79592 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
2023-12-17mb/google/zork: Add and use APCB configuration dataMatt DeVillier
This file is identical to the copy currently found in the amd_blobs repository; it is simply being relocated since it is mainboard specific and does not need to be in an external repo. BUG=none TEST=build/boot morphius Change-Id: Ia78fcd065fbf4d5ba6ec4edc3f8f937badf66ecc Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79591 Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-17mb/google/brox: Disable EC/PD SW SyncShelley Chen
For initial debugging, we want to disable SW syncing. Will re-enable in the future. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot chromeos-bootimage run gbb_utility --get --flags <image> make sure that it returns 0xa39 Change-Id: I865e9585ab37d1328a0ff54c6343cdad2c02220c Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79569 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Keith Short <keithshort@chromium.org>
2023-12-16mb/google/{rex,ovis}: Decrease EPP to 45% for MTL performance expectationSukumar Ghorai
The default EPP is set at 50%, which is deemed insufficiently aggressive for meeting the MTL performance expectations in balance_performance mode. # cat /sys/devices/system/cpu/cpu0/cpufreq/energy_performance_preference balance_performance # iotools rdmsr 0 0x774 0x0000000080003f06 EPP=45% is giving the required performance in MTL. # iotools rdmsr 0 0x774 0x0000000073003d06 NOTE: Kernel changes are necessary to ensure that the EPP (Energy Performance Preference) configured in the BIOS is not overwritten: https://patchwork.kernel.org/patch/13461932 BUG=b:314275133 TEST=Build and boot. Change-Id: I1953994cdb4e9363fdd4b4728e3e5236276c06c8 Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79386 Reviewed-by: Jakub Czapiga <czapiga@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-16mb/google/nissa/var/uldren: Reduce boot time for non-touchscreen skuDtrain Hsu
Non-touchscreen sku will set related GPIOs to NC. If touchscreen enabled in overridetree for non-touchscreen sku, the boot time will be 6-7s. Set touchscreen probed to TOUCHSCREEN_UNKNOWN for reduce boot time from 6-7s to under 1s. BUG=b:316434359 BRANCH=firmware-nissa-15217.B TEST=Boot time (cbmem -t) from 6,460,972 to 922,844 Change-Id: I016ce762f726b7624bd060284f74f0992cb129b6 Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79585 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
2023-12-15mb/google/brya: Enable FSP UPD LpDdrDqDqsReTrainingBora Guvendik
FSP default value for LpDdrDqDqsReTraining is 1. For boards that didn't set LpDdrDqDqsReTraining to any value, 0 was being assigned and it caused black screen issue. BUG=b:302465393 TEST=Boot to OS with debug FSP, check LpDdrDqDqsReTraining = 1 Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Change-Id: I301a6e43f2944ffbc63431393378ab8b23450032 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79527 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-15mb/google: Reduce DA7219 mic detect threshold to 200ohmTerry Cheong
The original DA7219 is designed to use a 500ohm mic detection threshold. Some headset mics (e.g. Logitech H111) have a lower DC impedance that is lower than the threshold and thus cannot be detected. Lower the threshold to 200ohm to match the new default value provided by Renasas as in https://patchwork.kernel.org/project/alsa-devel/patch/20231201042933.26392-1-David.Rau.opensource@dm.renesas.com/ to support such headsets. BUG=b:314062160,b:308207450 Change-Id: I6415e84a4622e0c61bc74b94536fe734048a043f Signed-off-by: Terry Cheong <htcheong@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79436 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-15mb/google/brya/var/dochi: Enable LpDdrDqDqsReTrainingMorris Hsu
FSP default value for LpDdrDqDqsReTraining is 1. For boards that didn't set LpDdrDqDqsReTraining to any value, 0 was being assigned and it caused black screen issue. BUG=b:302465393,b:315739133 TEST=Boot to OS with debug FSP, check LpDdrDqDqsReTraining = 1 Change-Id: I5d61301fddac6630bb1c48e992dd76e5cf02a272 Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79533 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-14mb/google/rex/var/screebo: Change GPP_B14 from UP_20K to NONEKun Liu
Change GPP_B14 from UP_20K to NONE for compatible with DVT1 and DVT2 board BUG=b:272447747 TEST=enable usb OC2 function to ensure USBA work normal Change-Id: Ib7720980335660f423b3a74199ceedc113ec70df Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79431 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-14mb/google/nissa/var/anraggar: Update DTT settings for thermal controlWeimin Wu
Update DTT settings based on the suggestion of the thermal. BUG=b:313833488 TEST=emerge-nissa coreboot Change-Id: I2296990062cadc05202e3d1ab90af04234bda885 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79442 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-14mb/google/nissa/var/anraggar: Enable USB3 Port3 for WWAN (LTE)Weimin Wu
1. Ref to SCH, LTE use USB3 Port3, enable it. 2. Explicitly define the use of USB3 Port1 & USB3 Port2. BUG=b:315061146 TEST=can pass PCIe Hardware Compliance Test Change-Id: I03d6925020012fa740bbd0168a2f5b02ea6763b4 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79381 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-14mb/google/nissa/var/anraggar: Change code style for register usb2_portsWeimin Wu
Change code style to be compatible with Nissa's format: register "option" = "{ [0] = value /* comment */ ... }" to register "option[0]" = "value" /* comment */ BUG=none TEST=abuild -v -a -x -c max -p none -t google/brya -b anraggar Change-Id: I60659bd44813173f9b984216473a0919c5f331b8 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79376 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-13mb/google/brox: Generate RAM ID for supported memory partIvy Jian
Add the MICRON MT62F1G32D2DS-023 WT:B RAM part for brox: DRAM Part Name ID to assign MT62F512M32D2DR-031 WT:B 0 (0000) H9JCNNNBK3MLYR-N6E 0 (0000) MT62F1G32D4DR-031 WT:B 1 (0001) MT62F1G32D2DS-023 WT:B 2 (0010) BUG=b:311450057,b:315913909 BRANCH=None TEST=Run part_id_gen tool without any errors Change-Id: Id120a5eb311d8299a8e59d2c1658fe0742e93934 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79459 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2023-12-12mb/google/rex/var/screebo: Increase PL1 max value from 15W to 25WKun Liu
Adjust PL1 max value from 15W to 25W BUG=b:314263021 TEST=emerge-rex coreboot Change-Id: I4122a13d7e33c736299c1a759ec51f7a3b29340f Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79377 Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-11mb/google/nissa/var/quandiso: Tune P-sensorRobert Chen
Update proximity sensor tuning value from dedede/kracko tuning. Remove GPIO override to use the configuration from nissa baseboard: - GPP_B5 ==> SOC_I2C_SUB_SDA - GPP_B6 ==> SOC_I2C_SUB_SCL BUG=b:310050220 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot Change-Id: I7c687677a797415d80be4c420484d3346a8455f6 Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79247 Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-08Revert "nipperkin: Fix WLAN to GEN2 speed" & "Disable PSPP for WLAN"Zheng Bao
Updated Linux FW works with PCI gen3 speed and PSPP. This reverts commit 05c9a850fd21 ("mb/google/nipperkin: Fix WLAN to GEN2 speed") https://review.coreboot.org/c/coreboot/+/63593 and commit 76fddd963925 ("mb/google/nipperkin: Disable PSPP for WLAN") https://review.coreboot.org/c/coreboot/+/63722 The changes are overlapped and are reverted together. BUG=b:240426142 & b:228830362 The system is able to ran over 2500 cycles on Nipperkin with command suspend_stress_test -c 10000 --wake_min 10 --suspend_min 10 \ --nofw_errors_fatal The whole variant_update_dxio_descriptors is empty and is pushed back to weak function. Change-Id: Id207076542edc8ea0cabc6e02e29856c2b6803c7 Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79172 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Van Patten <timvp@google.com>
2023-12-08mb/google/rex/var/screebo: set audio GPIO pins based on fw_configTerry Cheong
Enable BT offload when I2S option is selected for screebo. BUG=b:275538390 TEST=Verified audio playback using BT speaker/headset in I2S mode on google/screebo. Fixes: https://review.coreboot.org/c/coreboot/+/77755 Change-Id: I7ebe8e28d35428ce2fb8129dc145fec9ac60f9da Signed-off-by: Terry Cheong <htcheong@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79378 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-08mb/google/nissa/var/anraggar: Fix unrecogniz Type-C USB disk on depthchargeWeimin Wu
Due to TCPC0 & TCPC1 exchanged compare to Neried design, but related USB2 Ports not exchanged, keep mainboard C port to conn0. BUG=b:312998945 TEST=can boot from external Type-c USB disk Change-Id: Ib8df4a256bd9cd1b2ca229b09d68f97babc8092e Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79372 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-08mb/google/brox: Update configuration for USB portsIvy Jian
Update brox devicetree based on the latest schematics. - Configure typeC to EC mux ports settings. - Configure USB2/USB3 ports settings. - Configure TCSS ports settings. BUG=b:311450057 BRANCH=None TEST=emerge-brox coreboot Change-Id: Iac5a2e8be6cea64f107d267d4cf71529f08bb63d Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79391 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-06mb/google/brox: Generate RAM IDs for two modulesIvy Jian
Add the support LP5 RAM parts for brox: 1. HYNIX LPDDR5 6400 2GB H9JCNNNBK3MLYR-N6E 2. MICRON LPDDR5 6400 4GB MT62F1G32D4DR-031 WT:B DRAM Part Name ID to assign H9JCNNNBK3MLYR-N6E 0 (0000) MT62F1G32D4DR-031 WT:B 1 (0001) BUG=b:311450057 BRANCH=None TEST=Run part_id_gen tool without any errors Change-Id: Ib17f26a310435e37088191594863a645aa751440 Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79392 Reviewed-by: Shelley Chen <shchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2023-12-06mb/google/rex/variants/deku: Enable CNVi PCI deviceEran Mitrani
BUG=b:305793886 TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku Change-Id: I41a64252f08304ffc66fd782e54720252064ca49 Signed-off-by: Eran Mitrani <mitrani@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79398 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-05mb/google/brox: Fix memory configShelley Chen
Fix up the memory config for brox based on the schematics. Also, since memory training needs to happen in romstage, initializing the MEM_STRAP & MEM_CH_SEL gpios for use in romstage. Also consolidating the GPIOs needing to be initialized in romstage into the baseboard gpio.c file. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I17615cda7df10e73e49fb49f736728787ef7625d Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79355 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-12-04mb/google/rex/var/screebo: Override power limitsSubrata Banik
This patch allows variants to override the default baseboard PLx limits. Additionally, rearrange the include header files alphabetically. BUG=b:313667378 TEST=Able to boot google/screebo with modified power limits. Before: [DEBUG] WEAK: src/mainboard/google/rex/variants/baseboard/rex/ ramstage.c/variant_devtree_update called [INFO ] Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW) (40000, 40000) PL4 (W) (84) After: [INFO ] Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW) (40000, 40000) PL4 (W) (84) Change-Id: Ic66872c530963238a0bf5eebbd5b5a76a7985e5c Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79330 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2023-12-04mb/google/rex/variants/deku: Complete USB configurationEran Mitrani
+-------------+----------------+------------+ | USB 2.0 | Connector Type | OC Mapping | +-------------+----------------+------------+ | 1 | Type-C | OC_0 | +-------------+----------------+------------+ | 2 | Type-C | OC_0 | +-------------+----------------+------------+ | 3 | Type-C | OC-0 | +-------------+----------------+------------+ | 4 | Type-A | OC_3 | +-------------+----------------+------------+ | 5 | Type-C | OC_0 | +-------------+----------------+------------+ | 6 | Type-A | OC_3 | +-------------+----------------+------------+ | 7 | Type-A | OC_3 | +-------------+----------------+------------+ | 8 | Type-A | OC_3 | +-------------+----------------+------------+ | 9 | Type-A | OC_3 | +-------------+----------------+------------+ | 10 | BT | NA | +-------------+----------------+------------+ +---------------------+-------------------+------------+ | USB 3.2 Gen 2x1 | Connector Details | OC Mapping | +---------------------+-------------------+------------+ | 1 | Type-A | OC_3 | +---------------------+-------------------+------------+ | 2 | Type-A | OC_3 | +---------------------+-------------------+------------+ +------+-------------------+------------+ | TCPx | Connector Details | OC Mapping | +------+-------------------+------------+ | 1 | Type C port 0 | OC_0 | +------+-------------------+------------+ | 2 | Type C port 1 | OC_0 | +------+-------------------+------------+ | 3 | Type C port 2 | OC_0 | +------+-------------------+------------+ | 4 | Type C port 3 | OC_0 | +------+-------------------+------------+ BUG=b:305793886 TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku Signed-off-by: Eran Mitrani <mitrani@google.com> Change-Id: I90d3d984af6d40efb4553cf5675617700161d2d7 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79356 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-04mb/google/rex/variants/deku: Add basic DTTEran Mitrani
Add default Intel DPTF. BUG=b:305793886 TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku Signed-off-by: Eran Mitrani <mitrani@google.com> Change-Id: Id681754fc8e7b418de35f66df097cadd4aad7448 Signed-off-by: Eran Mitrani <mitrani@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79353 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-04mb/google/rex/var/deku: Enable LAN0, LAN1Eran Mitrani
google/deku is a Chromebox featuring two LAN ports. Add overridetree.cb entry to configure the LAN0 LAN1 devices. BUG=b:305793886 TEST=Built FW image correctly. Signed-off-by: Eran Mitrani <mitrani@google.com> Change-Id: I8980dabc7f9fc731a2b60c599e1e48c9b11dabb4 Signed-off-by: Eran Mitrani <mitrani@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79292 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-12-04mb/google/rex/var/ovis: Add power limit support for MCH ID 0x7d14Subrata Banik
This patch adds the power limit configuration for MCH ID index 3 aka 0x7d14 DID which is identical to MCH ID 0x7d01 (index 1). TEST=Able to perform power limit configuration for google/ovis. [DEBUG] WEAK: src/mainboard/google/rex/variants/baseboard/ovis/ ramstage.c/variant_devtree_update called [INFO ] Overriding power limits PL1 (mW) (19000, 28000) PL2 (mW) (64000, 64000) PL4 (W) (120) Change-Id: Iff71adb4e26d18970b5947927c258419f751de32 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79332 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2023-12-04mb/google/rex: Simplify power limit configuration usageSubrata Banik
This patch removes the deprecated PL_PERFORMANCE and PL_BASELINE configurations, relying instead on the refactored power limit flow. This flow allows for seamless overrides by the baseboard and/or by the variant board, if necessary. Specifically, this patch: - Removes PL_PERFORMANCE and PL_BASELINE configuration options from mainboard.c in the google/rex directory. - Relies on the baseboard_devtree_update() function, which is implemented by the respective baseboard, to handle power limit configuration. - Leverages the variant_devtree_update() function, which is a __weak implementation, to allow overrides by the variant directory. This simplification improves code readability and maintainability while maintaining the flexibility to handle power limit configurations as needed. Change-Id: I872e5cb59d7b2789ef517d4a090189785db46b85 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79331 Reviewed-by: Kapil Porwal <kapilporwal@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-02mb/google/rex: Enhance power limit override mechanismSubrata Banik
This patch expands the power limit override capability to include variants directories, enabling them to modify power limit settings configured by the baseboard. Previously, only the baseboard could override power limit settings. For instance, while the google/rex baseboard sets the PL1 max power limit to 15W, the google/screebo variant couldn't override this value. This enhancement empowers variants directories to override baseboard- configured power limit settings, allowing for greater flexibility and control over power limits. BUG=b:313667378 TEST=Able to call into _weak implementation of `variant_devtree_update` unless there is one override. [DEBUG] WEAK: src/mainboard/google/rex/variants/baseboard/rex/ ramstage.c/variant_devtree_update called [INFO ] Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW) (40000, 40000) PL4 (W) (84) Change-Id: Ib07691625e075b0fbab42271512322ffc60ba13b Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79329 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2023-12-01mb/google/nissa/var/anraggar: Trim GPIO commentsWeimin Wu
Trim all GPIO comments like "origin ==> current". BUG=b:304920262 TEST=pass building Change-Id: I05daa4df16b6da3d3f971b75c7c467032e3f854d Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79321 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-12-01mb/google/nissa/var/anraggar: Fix the GPP_D6 for LTE power.Weimin Wu
Fix GPP_D6 configuration for LTE power enable. BUG=b:304920262 TEST=mmcli -m any Change-Id: I2996fd35c2897269997bc0290e0ce93bbbaa1bf8 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79166 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
2023-12-01mb/google/nissa/var/anraggar: Fix Type-C & DP functionsWeimin Wu
Due to TCPC0 & TCPC1 exchanged compare to Neried design, but related USB2 Ports not exchanged. BUG=b:304920262 TEST=Tpye-C & DP functions workable Change-Id: I9dacf06b1e672575a684856acdb10b6c88360b18 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79165 Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-01mb/google/nissa/var/anraggar: Enable ILITEK touchscreenWeimin Wu
For proto PCB: GPP_C0 for enable power supply which also for sensor subsystem. GPP_C0 must allways turn power on, so GPP_C6 is not only used for enable function but also for stop report. BUG=b:304920262 TEST=1. touchscreen function workable 2. INT pin no active during suspend Change-Id: I7dabf205dba616f57ef9717f950eba96282d8e3d Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79164 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
2023-12-01mb/google/brya/var/dochi: Update overridetree for type c1Morris Hsu
Update overridetree to correct AUX pin to USB-C port 3 BUG=b:299570339 TEST=emerge-brya coreboot chromeos-bootimage Change-Id: I3a5a89c6008fbf28c927f83060e6e508d60845ba Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79343 Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-12-01mb/google/brox: Update storage settings for SSD and UFSIvy Jian
Brox has SSD and UFS storage per different SKU. 1. Set SSD on CPU PCIe port (PCIEX4_A) and configure related gpio settings according to the schematic. 2. Enable UFS, also enable ISH since it is PCI function 0, required for UFS function 7 to be enabled. 3. Set unused SRCCLKREQ signals to NC. 4. Remove unused gpio settings in variant gpio table to prevent unexpected overrides. BUG=b:311450057 BRANCH=None TEST=emerge-brox coreboot Change-Id: I88922bcfa13652006aa10078c3c444624fd4575e Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79295 Reviewed-by: Shelley Chen <shchen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/rex/variants/deku: Add GPIO configurationEran Mitrani
Based on Platform Mapping Document for Deku (go/cros-deku-mapping) from Nov 8, 2023 (Rev 0.4) BUG=b:305793886 TEST=WIP, not tested yet Change-Id: Ib37a7ebf0aca788d14fafea0f97e364beafb4c4d Signed-off-by: Eran Mitrani <mitrani@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78960 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2023-11-30mb/google/corsola: Use fw_config to differentiate audio ampsYidi Lin
Use fw_config to differentiate audio amps instead of the kconfig option. BRANCH=corsola BUG=b:305828247 TEST=Verify devbeep in depthcharge console Change-Id: I5f887f5e0d16dc14039fb12b636257d01339b2de Signed-off-by: Yidi Lin <yidilin@chromium.org> Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79309 Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/nissa/var/quandiso: Add LTE only daughterboard supportRobert Chen
Quandiso does not use DB_1C, replace the fw_config with LTE only daughterboard. BUG=b:312094048 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot Change-Id: Id7129e52d3733f62405f9d766f08563f05016c69 Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79297 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Shawn Ku <shawnku@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/galdos/var/lars: Implement touchscreen power sequencingMatt DeVillier
Since lars has two touchscreen options, we need to determine which (if any) are present on a given device at runtime so that there are not multiple ACPI touchscreen devices (as it makes Windows unhappy). Implement power sequencing and runtime detection for both touchscreen options. TEST=build/boot Win11/Linux on google/lars, verify touchscreen detected and functional under both OSes. Change-Id: I49ccb29ec4589315a4abe3c0ea8fa76f97080bcd Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79311 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-11-30mb/google/glados/var/lars: Add Melfas touchscreenMatt DeVillier
LARS has a Melfas touchscreen option, so add an entry for it. Adapted from Chromium branch firmware-glados-7820.315.B, commit a26fe552569f ("Chell: Update DPTF parameters for CPU"). TEST=build/boot Linux on google/lars with Melfas touchscreen, verify functional. Change-Id: Idecd572335d7d5d52e4f89e85ebf7f0c90f23751 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79310 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/nissa/var/anraggar: Add OV13B10 MIPI camera deviceWeimin Wu
Enable MIPI camera for anraggar project. Sensor: OV13B10-GA5A Driver: DW9714V EEPROM: GT24P64E Ref to SCH, use MIPI 4-lane serial output interface. BUG=b:309518095 TEST=Google Camera app working Checking log with: coreboot log: \_SB.PCI0.I2C2.CAM0: Intel MIPI Camera Device I2C address 036h \_SB.PCI0.I2C2.VCM0: Intel MIPI Camera Device I2C address 0ch \_SB.PCI0.I2C2.NVM0: Intel MIPI Camera Device I2C address 050h kernel log: kernel: [ 6.140429] intel-ipu6-isys intel-ipu6-isys0: bind ov13b10 11-0036 nlanes is 4 port is 1 cros_camera_service[4755]: Read camera eeprom from /sys/bus/i2c/devices/i2c-PRP0001:02/eeprom cros_camera_service[4755]: Probing media device '/dev/media0' cros_camera_service[4755]: Probing sensor 'ov13b10 11-0036' (v4l-subdev17) cros_camera_service[4755]: Found V4L2 sensor subdev on /sys/devices/pci0000:00/0000:00:15.2/i2c_designware.2/i2c-11/i2c-OVTIDB10:00/video4linux/v4l-subdev17 Change-Id: I6a82557c94203f24449588a6005abc53cc29ca76 Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79163 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arec Kao <arec.kao@intel.corp-partner.google.com>
2023-11-30mb/google/nissa/var/anraggar: Enable CNVi BluetoothWeimin Wu
Intel CNVi WLAN's BT uses USB2 Port 10 inside the SOC, and the relevant configuration needs to be modified in overridtre.cb. BUG=b:304920262 TEST=lsusb ID 8087:0033 Intel Corp. rfkill list hci0:Bluetooth Change-Id: Ibcae800836c17307bc133de5a91658f6dda5985c Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79055 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/nissa/var/anraggar: Tune eMMC DLL valuesSimon Yang
Anraggar cannot boot into OS and kernel loading failure. Update eMMC DLL values to improve initialization reliability - Sending different speed TX/RX command/data signal to eMMC and check the response is success or not. - Collecting every eMMC that use for the project - Based on above result to provide a fine tune DLL values BUG=b:308366637 TEST=Cold reboot stress test over 2500 cycles Change-Id: I9ec3cc23000301aa72aed96e74b63114623c4fc2 Signed-off-by: Simon Yang <simon1.yang@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/78851 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-11-30mb/google/brya/var/marasov: Update MSR Package Power Limit-1 valuesDaniel Peng
As customer demand, it is necessary to set MSR Package Power Limit-1 to 17W for the DTT setting to optimize performance. The PL1 value (17W) suggested by the thermal team which is different from the reference code(PL1=15W). BUG=b:312321601 BRANCH=firmware-brya-14505.B TEST=emerge-brya coreboot chromeos-bootimage Built and booted into OS, and confirm MSR PL1=17W correctly. Change-Id: If7874d26038118c5605cf0721c30e681b45123fe Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79335 Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-30mb/google/brya: Centralize SOC_INTEL_STORE_ISH_FW_VERSION configSubrata Banik
This patch moves the SOC_INTEL_STORE_ISH_FW_VERSION config from the Nissa baseboard to BOARD_GOOGLE_BRYA_COMMON. This allows all baseboards to retrieve the ISH version and store it into memory. Ensure SOC_INTEL_STORE_ISH_FW_VERSION is enabled only for platforms with ISH support (DRIVERS_INTEL_ISH). Additionally, the dedicated SOC_INTEL_STORE_ISH_FW_VERSION config selection for the Nissa baseboard is no longer needed. BUG=b:280722061 TEST=Able to build and boot google/marasov. Change-Id: I99dab43ae4e13869b7f8797a9c4014f60e38a595 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79338 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2023-11-29mb/google/rex/var/screebo: Change GPP_B14 from NC to NFKun Liu
Change GPP_B14 from NC to NF BUG=b:272447747 TEST=enable usb OC2 function to ensure USBA work normal Change-Id: Ie0f112bcf183870869d0c1b9a223d4231600a300 Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79308 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2023-11-29mb/google/brox: Fix configuration for TPMShelley Chen
On Brox, TPM is using i2c4 and GPP_E2, so modifying the Kconfig to reflect this. Also, fixing up the TPM entry in the device tree. Making sure that the GPIO for GSC_PCH_INT_ODL is set correctly. BUG=b:300690448 BRANCH=None TEST=emerge-brox coreboot Change-Id: I0ecaa6fcfc05c3c2e55f857d7a4e59fe46096bb5 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79102 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
2023-11-27mb/google/brya/var/taeko: Generate SPD IDs for 2 new memory partsLeo Chou
Add taeko new supported memory parts in mem_parts_used.txt, generate spd-3.hex for these parts. 1. Samsung K4UBE3D4AB-MGCL 2. Micron MT53E1G32D2NP-046 WT:B BUG=b:312363368 TEST=Use part_id_gen to generate related settings Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com> Change-Id: I221ad3f490f24b43fe1ccd211014787eab5d1038 Reviewed-on: https://review.coreboot.org/c/coreboot/+/79184 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Bob Moragues <moragues@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: YH Lin <yueherngl@google.com>
2023-11-27mb/google/rex/var/screebo: Enable BT audio offload configKapil Porwal
Enable BT audio offload of ALC1019_ALC5682I_I2S based on fw_config. BUG=b:299510759 TEST=Build and boot to Screebo. Verify the config from serial logs. w/o this CL - ``` [SPEW ] ------------------ CNVi Config ------------------ [SPEW ] CNVi Mode = 1 [SPEW ] Wi-Fi Core = 1 [SPEW ] BT Core = 1 [SPEW ] BT Audio Offload = 0 [SPEW ] BT Interface = 1 ``` w/ this CL - ``` [SPEW ] ------------------ CNVi Config ------------------ [SPEW ] CNVi Mode = 1 [SPEW ] Wi-Fi Core = 1 [SPEW ] BT Core = 1 [SPEW ] BT Audio Offload = 1 [SPEW ] BT Interface = 1 ``` Signed-off-by: Kapil Porwal <kapilporwal@google.com> Change-Id: I6c713752f3f0bf58b5ebd78b904e773fdbf16e06 Reviewed-on: https://review.coreboot.org/c/coreboot/+/77755 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2023-11-27mb/google/nissa/var/craask: Enable PIXA touchpadTyler Wang
Add PIXA touchpad for variants of craask. BUG=b:310489697 TEST=build craask firmware and test with PIXA touchpad Change-Id: I7e68a44eb3d639eaadb5b7b9cb5a6955fd059eeb Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79212 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-by: Eric Lai <ericllai@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2023-11-24mb/google/nissa: make GPP_F17 edge triggered to avoid spamming ECScott Chao
In nissa platform, we configured GPP_F17 as SCI+APIC to wake the system and also generate IRQ to the IOAPIC. Currently, we set GPP_F17 to level triggered and it causes AP (Application Processor) to keep sending GET_NEXT_EVENT to EC during resume from suspend by connecting AC. So we change GPP_F17 to edge triggered to avoid this condition. BUG=b:308716748 TEST=Original failure rate was 7 out of 10 times and it reduced to 0 out of 60 times on six joxer systems. Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com> Change-Id: I3ceb1dfce46376a6a9a8c6cb6d691d818a0a42ff Reviewed-on: https://review.coreboot.org/c/coreboot/+/79244 Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Reka Norman <rekanorman@chromium.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2023-11-23mb/google/nissa/var/quandiso: Disable un-used C1 port by daughterboardRobert Chen
Probe usb ports by FW_CONFIG setting to disable C1 port on quandiso new daughterboard without C1 port. BUG=b:312094048 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot Change-Id: I6f702f60c772176e80b3452bf957d10625564102 Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79173 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-22mb/google/nissa/var/craaskov: Add 6W and 15W DPTF parametersVan Chen
The DPTF parameters were defined by the thermal team. Based on thermal table in 290705146#comment17. BUG=b:290705146 BRUNCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot chromeos-bootimage Change-Id: I02b4187000eec9990bf10a57875b23007f7bdd12 Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79183 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-22mb/google/rex: Enable FSP logo rendering for all Rex variantsSubrata Banik
This patch enables the FSP (Firmware Splash Screen) rendering feature for all Rex variants, including chromeboxes like Ovis. This will allow users to see the FSP logo during the boot process. BUG=b:284799726 TEST=Verify that the FSP logo is displayed during the boot process on an google/ovis chromebox. Change-Id: I73d82e16f70ffdc8cb168506c86d9c4e9a92c38d Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79175 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-11-22mb/google/rex/var/karis: Set pen detect pin to NC for non-stylus skuTyler Wang
Set pen detect pin to NC base on fw_config. BUG=b:304680060 TEST=emerge-rex coreboot pass Change-Id: Icf9171fca49cfed1a05a67ae7fc8d62b7e9630c9 Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79213 Reviewed-by: Subrata Banik <subratabanik@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-22google/*: Clean up Kconfg board selection for Google MTK boardsJulius Werner
This patch tries to standardize and simplify the Kconfig option layout for Google boards with MediaTek SoCs and align them to the scheme used with other Arm-based Google boards. Change-Id: I40880e7609ba703d0053ad01da742871e54d4e7a Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79063 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yidi Lin <yidilin@google.com>
2023-11-22google/*: Clean up Kconfig board selection for non-MTK Google Arm boardsJulius Werner
This patch unifies and simplifies the Kconfig selection model for the Gru, Herobrine, Trogdor and Veyron boards according to the model discussed in CB:78972. Also add missing license headers to two Kconfig files while I'm here. Change-Id: If679a05afd10869afba9c2a33b54862e102b5f40 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79022 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-21mb/{google,intel}/{rex,mtlrvp}: Enable SOC_INTEL_COMMON_BASECODE_RAMTOPSubrata Banik
This patch enables the `SOC_INTEL_COMMON_BASECODE_RAMTOP` config option for select mainboards, as not all board variants may want to enable this config due to underlying SoC dependencies. Mainboards that attempt to enable early caching have exhibited soft hangs while switching between pre-RAM and post-RAM phases. This patch allows mainboards to choose to enable this option without enabling it by default (which could cause boot hangs). Furthermore, it reorganizes the configuration options under BOARD_GOOGLE_BASEBOARD_REX in alphabetical order for better readability. BUG=b:306677879 TEST=Enable SOC_INTEL_COMMON_BASECODE_RAMTOP for google/rex and intel/mtlrvp. Change-Id: If380c2ecbee4f6437c3d58bfb55be076a4902997 Signed-off-by: Subrata Banik <subratabanik@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79048 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kapil Porwal <kapilporwal@google.com>
2023-11-21mb/google/nissa/var/joxer: Add speaker ldo configTerry Chen
Follow thermal validation, add ldo output select for speaker. BUG=b:297298847 TEST=emerge-nissa and deploy to DUT to verify audio functionality. Change-Id: Ie68f2b35f024b4dd066d831ae8fd5a662d407753 Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79111 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Derek Huang <derekhuang@google.com> Reviewed-by: Eric Lai <ericllai@google.com>
2023-11-21mb/google/byra/var/*: Set LAN device type back to pciMatt DeVillier
This partially reverts commit f493857c9bc1 ("mb/google/brya/var/*: Set dGPU/LAN/WLAN device type to generic"). Setting the LAN device type to generic broke programming the LAN MAC address, so set it back to pci. TEST=build/boot google/brya (osiris), verify LAN MAC address programmed correctly. Change-Id: I4fb43b7212e67b5c38724baad572860bc45b558e Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79150 Reviewed-by: Eric Lai <ericllai@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2023-11-21mb/google/puff/var/*: Set LAN device type back to pciMatt DeVillier
This mostly reverts commit 6c705e766f7f ("mb/google/puff/var/*: Set LAN/WLAN device type to generic"). Setting the LAN device type to generic broke programming the LAN MAC address, so set it back to pci. TEST=build/boot google/puff (wyvern), verify LAN MAC address programmed correctly. Change-Id: I558ae6dc1366d5a8a22e0383d7d597d15159df03 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79149 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
2023-11-20mb/goog/brya/var/brya0/skolas: Disable HPS GPIOs if HPS_ABSENTNick Vaccaro
Check FW_CONFIG and disable gpios for HPS if HPS_ABSENT for skolas and brya0 variants. BUG=b:311740746 BRANCH=firmware-brya-14505.B TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot skolas to kernel and verify via "cbmem -c | grep HPS". Change-Id: I8cbe4f40c41f1d06e8f511c3e88c05984566d441 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/79123 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <ericllai@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-22 14:29:43 +0000