| Age | Commit message (Collapse) | Author |
|---|
|
Follow spec[1] to modify WWAN power sequence. The WWAN power sequence
of warm reset is fail. The correct sequence is WWAN_EN should keep high when doing warm reset. Set GPP_D6 to PWROK which is not to do PAD
reset when warm reset.
[1]:
[JDB10] FC ADL-N_WWAN sequence_FM101-GL SDX12 Power Timing
Review_V1.6_20230602.xlsx
BUG=b:285065375
BRANCH=firmware-nissa-15217.B
TEST=1. emerge-nissa coreboot chromeos-bootimage
2. power sequence meets spec.
Change-Id: If59630dbd10e971c91e01f33a657c01d857bc0b9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75690
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable wifi sar function for yavilla/yavilly/yavijo.
Use the fw_config to separate SAR setting for different wifi card.
BUG=b:286141046
BRANCH=firmware-nissa-15217.B
TEST=build, enabled iwlwifi debug, and check dmesg
Change-Id: I1bd111a734a250df49535a07ef056d5b68fccb33
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add new memory parts
DRAM Part Name ID to assign
Hynix H58G66AK6BX070 3 (0011)
Hynix H9JCNNNFA5MLYR-N6E 4 (0100)
Micron MT62F2G32D8DR-031 WT:B 4 (0100)
BUG=b:279325772
BRANCH=firmware-brya-14505.B
TEST=run part_id_gen to generate SPD id
Change-Id: I2e6a916de08e7c05e95909d2b69bc839d13192d9
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74713
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
The memory parts being added are:
1. K4U6E3S4AB-MGCL
2. K4UBE3D4AB-MGCL
BUG=b:285504022
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I87a4dcdb6196c3ca7bed4b5c1bc654297339c16d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75605
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of adding the new PCI IDs of the XHCI controllers in every new
chip generation to the pci_xhci driver, bind the driver to the internal
PCI devices of the XHCI controllers via the device ops statement in the
chipset devicetree. The PCI device function of the XHCI2 controller in
Mendocino can be either a dummy device or the XHCI controller, so the
device ops are attached to that device in the mainboard devicetree
instead. The Glinda code is right now just a copy of the Mendocino code,
so it'll change in the future, but for consistency the equivalent
changes to those in Mendocino are applied there too.
Since the device ops are now attached to the devices via the static
devicetree entry, also remove both the xhci_pci_driver struct and the
amd_pci_device_ids array from drivers/usb/pci_xhci/pci_xhci.c.
TEST=SSDT entries for the XHCI controllers are still generated on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c455002c6d2aac576fe24eee0c31744b4507bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Initialize the SPI Flash in bootblock to ensure that
CONFIG_SPI_FLASH_EXIT_4_BYTE_ADDR_MODE will exit 4-byte addressing mode.
BUG=b:285110121
TEST=boot myst and verify flash operations work correctly
Change-Id: Ia88d2b46884b096b4c558bc86513159ec6d35eb5
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75588
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for Micron MT53E2G32D4NQ-046 WT:C LP4x DRAM.
BUG=b:216393391
TEST=build pass
Change-Id: I0abf1f1105f9a6f16af23b0ed3eb4faeb669eee6
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75716
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Include the GPU ACPI methods for all of Hades baseboard.
BUG=b:285981616
TEST=built for Hades and verify shutdown works
Change-Id: Iec3c4b59a9e7a9d4a902db51d40b60e114521774
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
HW has invert the signal, set it to active high.
BUG=b:285964562
TEST=check crossystem wpsw_cur change as expected.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I54c578e5df5f1b24743cc9506e1e31b0b18bfb25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75628
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add usb wwan device tree entry. Also set wwan_rst to high due to
HW design active high.
BUG=b:285792436
TEST=check FM101 is detected by Linux kernel.
Bus 002 Device 002: ID 2cb7:01a2 Fibocom Wireless Inc.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0aa60cb284d4b7f99e16643a92ee58467a355026
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75660
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add fingerprint into device tree. Also set RST to low per HW
requirement.
BUG=b:285799911
TEST=check ectool --name=cros_fp version.
RO version: bloonchipper_v2.0.5938-197506c1
RO cros fwid: CROS_FWID_MISSING
RW version: bloonchipper_v2.0.14348-e5fb0b9
RW cros fwid: bloonchipper_14931.0.0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I09819037b80e55edeb56faef9e27fe0753748efc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75629
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new GFX devices for DDI and TCP with custom _PLD to describe the
corresponding ports.
BUG=b:277629750
TEST=emerge-brya coreboot
BRANCH=firmware-brya-14505.B
Change-Id: Ia083617c58d6b7ebc108e07e29a1c8061580eae5
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: I3795313e784595ac02ee2a38f466bcb9e613a6a4
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75576
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jan Dabros <dabros@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I1644b1d8f49accbb2ea68e236534df80a5151360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75503
Reviewed-by: Jan Dabros <dabros@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Based on Platform Mapping Document for Ovis (go/ovis_mapping_doc)
state for June 6, 2023 (Rev 0.3)
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Iae3ca243a245928e8ec3d48877cf578843922fc7
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75502
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
joxer removed SD card from all SKUs, thus disable pcie_rp7.
BUG=b:285477026
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I3486d665ddb1de521ab4e656addb2209055174c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75658
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Board IDs are now filled in as part of the signing process, so we don't
need to set them in coreboot.
BUG=b:240620735
TEST=Build and check VBOOT_GSC_BOARD_ID is set to ZZCR.
Change-Id: I7dda8ad59046a1dd9a28595e037eda86e91c98df
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75641
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new GFX devices for DDI and TCP with custom _PLD to describe the
corresponding ports.
BUG=b:277629750
TEST=emerge-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: I193b95e8bd8ae538c4f25fbe772b174ef455d744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
All the DRAM module for Juniper/Willow can reuse the RAM ID in
offset 0x30 table, so change Juniper/Willow RAM table offset to 0x30
for introducing more DRAM modules.
BUG=b:284423187
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I92740275dcc27061a94b7db7ce095655c0bd7cf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Uldren does not have PCIE device and should disable PCIE RP7 and
GPP_D7 for preventing PCIe controller not power gate in S0ix.
BUG=b:283735051
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
1. PCIE RP7: cbmem -c | grep 'PCI: 00:1c.6'
[SPEW ] PCI: 00:1c.6: enabled 0
[SPEW ] PCI: 00:1c.6: enabled 0
2. GPP_D7: iotools mmio_read32 0xfd6d0ab0
0x44000300
Change-Id: Ia8a2c0f5530c7a056e8d706c651cac1d49b2091c
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75644
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Ic555fac846ebf1e9dad81b5847334c03d6804b5b
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a ; Make sure
GOOGLE_OVIS built successfully
Change-Id: I5c8f290cfdcb4d47c0e5e9d72c1e34073b957681
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75385
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The K&D-ILI9882T panel and STA-ILI9882T share all DCS commands and EDID
information except for the manufacturer_name which has no effect to the
function of panel. Let's reuse the STA_ILI9882T struct in this case.
BUG=None
TEST=emerge-staryu coreboot chromeos-bootimage and boot the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I510462a49d273f3d25158b25906d4c514f855cdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Based on the power sequence of the panel [1], the power on T2 sequence
VSP to VSN should be larger than 1ms, and the power off T2 sequence VSP
to VSN should be larger than 0ms. We modify the power sequence to meet
the datasheet requirement.
[1] B5 TV110C9M-LL0 Product Specification Rev.P0
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I4ccb5be04062a0516f84a054ff3f40afbf5279be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Touchscreen may either use I2C1 or SPI0.
FW_CONFIG.TOUCHSCREEN is set to determine which is used.
This CL adds a probe to enable I2C1.
BUG=b:278783755
TEST=Tested on rex, confimed i2c1 is disabled when
TOUCHSCREEN != TOUCHSCREEN_I2C
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I0bee176298fddd2aee35cf084db037a3ce7672f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Follow 57263_FP8_MBDG_rev_0_92 Table.57 to update the alias. We
can match the schematic for now.
BUG=b:285793461
TEST=USB still works.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Id1058279fe5b0e3131608a0b9bbd708dbbde7e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Makefile.inc to include four LPDDR5x SPDs for the following
parts for Joxer:
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 3 (0011)
H58G56BK7BX068 4 (0100)
MT62F1G32D2DS-026 WT:B 4 (0100)
K3KL8L80CM-MGCT 4 (0100)
BUG=b:236576115
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ibdc89c882581cfe4e5978faf4c6f70d653e0813d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75610
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I2a6de778c7ab30a9946e100cb70c092ba98496e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74944
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: I5c0395d33ee47ab1c7d45f33d6afb063b8263836
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75572
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: I51ff0991565d60807c100b33fb66ab10cc48b8e1
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: Ib564ffe272e73f46ec6608420dc431c8b017fb65
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Select SOC_INTEL_RAPTORLAKE for kuldax so that it will use the RPL
FSP headers for kuldax.
BUG=b:285406822
BRANCH=firmware-brya-14505.B
TEST="FW_NAME=kuldax emerge-brask
coreboot-private-files-baseboard-brya coreboot chromeos-bootimage"
Cq-Depend: chromium:4583807, chrome-internal:6003096
Change-Id: Icbf8b26bc2bfee2559cce236bde80a99f8bff859
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75599
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Fast VMode nmakes the SoC throttle when the current exceeds the I_TRIP
threshold.
BUG=b:285406822
BRANCH=firmware-brya-14505.B
TEST=Verify that the feature is enabled by reading from fsp log
Change-Id: I9ae58d704cba8124c6cb9865431aff84c9d154f7
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75600
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add the phoenix usb config struct for Myst since the FSP has been
updated to accept the config from coreboot and the default values
do not work.
BUG=None
TEST=Boot to OS on Myst, verify devices are seen with lsusb
Change-Id: I329aba80f3003a3a5f343b8dcc3efa8502b98e24
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Enable ISH based on FW_CONFIG obtained from EC CBI. This is useful in
case device is a tablet and motion sensors are handled by ISH instead
of EC.
BUG=b:280329972,b:283023296
TEST= Set bit 21 of FW_CONFIG with CBI
Boot rex board
Check that ISH is enabled and loaded
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Ibe0e1b8ce2c9b08ac6b1e6fef9bd19afc9b4f59f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75039
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix for the "Onboard Keyboard and Type-C ports are not working after
resuming from powerd_dbus_suspend" issue. This issue was caused since
FSP 3165 FSP was fixed and started skipping GpioConfigureIoStandbyState
programming when GpioOverride UPD is enabled.
This patch moves the IO Standby State programming that FSP was doing to
coreboot.
BUG=b:284264580
TEST=Boot to OS, compare gpio pins, verify keyboard / Type-C
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If96c1e71fdde784a55fe079875915ffa5a4f548a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75555
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree config for ALC1019_ALC5682I_I2S
BUG=b:278169268
TEST=emerge-rex coreboot and verified on screebo
Change-Id: I2814cc76aff43daf0353cfef41592591bbe3d213
Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
On Myst, the FSP is shutting down the PCIe lanes that the SSD is
on. Enable hotplug to force the FSP to keep the lanes active.
BUG=b:284213391
TEST=Boot to OS
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Iaf0aca329f05f15a3ce9edfa6a0e782c2edccabe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Enable s0ix on Myst.
BUG=b:277215113
TEST=builds
Change-Id: I3cabc2c3ba75f4490da18b861ef2b82ce240860d
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74279
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Google/Rex is built with Intel Meteor Lake-U SoC, so select it.
Currently, there is no functional difference, but in the future FSP
UPD parameters can be overridden properly.
BUG=b:276697173
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4c233e0a8ce58998dc1a0379662e386f9b3d0073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75612
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the karis variant of the rex0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:285195072
TEST=util/abuild/abuild -p none -t google/rex -x -a
make sure the build includes GOOGLE_KARIS
Change-Id: I16d8b43390401789b87a6233238e37f32a17b46b
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Generate RAM ID for Samsung K4UCE3Q4AB-MGCL
DRAM Part Name ID to assign
K4UCE3Q4AB-MGCL 3 (0011)
BUG=b:281950933
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I75818b8a34d010fc0efe90c7625162e40e3b0dca
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Generate RAM ID for Samsung K4UCE3Q4AB-MGCL
DRAM Part Name ID to assign
K4UCE3Q4AB-MGCL 3 (0011)
BUG=b:281943392
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I79b29b1195468272c7f64a0eeb15d032eff8c1d3
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch adds FW_CONFIG to accommodate different Screebo BOM
components across various SKUs.
1. DB_CONFIG for DB_TPEC/DB_TBT/DB_UNKOWN
2. AUDIO for ALC1019_ALC5682I_I2S/AUDIO_UNKNOWN
BUG=b:278169268
TEST=build pass
Change-Id: I928aae61d4936509a7b68f4041c0cd72f298e83d
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow the eKTH7B18U_Product_Spec_V1.1 to add the device.
BUG=b:284381267
TEST=Check touch screen can detect in coreboot.
[INFO ] \_SB.I2C1.H010: ELAN Touchscreen at I2C: 02:10
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I4bd521410953892a477020a872de0d882001b178
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Follow the data sheet SA577C-12C0, Rev. 1.1 to add the device.
BUG=b:284381266
TEST=check touch pad can detect in coreboot.
[INFO ] \_SB.I2C0.D015: ELAN Touchpad at I2C: 01:15
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0eb0ee1e6cb9c15bfe3964af6ce2ed02eee370a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Follow the schematic_0502 to add the audio codec and amp.
BUG=b:270109435
TEST=Check device can detect in coreboot.
[INFO ] \_SB.I2C3.RT58: Realtek RT5682 at I2C: 04:1a
[INFO ] \_SB.I2C3.D029: Realtek SPK AMP R at I2C: 04:29
[INFO ] \_SB.I2C3.D02A: Realtek SPK AMP L at I2C: 04:2a
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Icfec8d99be8fde986c5516e0c4cd50dae1edfa98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75477
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power sequence of the panel [1] and PMIC datasheet [2],
the power on T2 sequence VSP to VSN should be large than 1ms, but it's
-159us now, and the power off T2 sequence VSP to VSN should be large
than 0ms, but it's less than 0 now. Let's modify the power sequence
to meet the datasheet requirement.
[1] HX83102-J02_Datasheet_v03.pdf
[2] TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:282902297
TEST=power sequence T2 pass
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ib1625c6a211f849071393f69eaf5c649a8e7f72e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75298
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DPTF parameters were verified by the thermal team.
BUG=b:282598257
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I1f38ef52d3906960f8b692595fcc3b39bc000243
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Enabling MIPI UCAM for screebo project
BUG=b:277883010
TEST=none
Signed-off-by: jason.z.chen <jason.z.chen@intel.corp-partner.google.com>
Change-Id: Id06e5c162d911a4bd78190757c25e7f760160a8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Haikun Zhou <zhouhaikun5@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set tcc_offset value to 20 in devicetree for Thermal Control Circuit
(TCC) activation feature for proto phase.
BUG=b:282865187
BRANCH=None
TEST=Build FW and test on Screebo board
Change-Id: I3a929aa20a700376d2a0a150911fed34e67f78eb
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75360
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Haikun Zhou <zhouhaikun5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Incorrect filename "MakeFile.inc" cause gpio.c can not be complied.
Rename to "Makefile.inc" and confirm gpio.c can load correctly.
BUG=b:281620454
BRANCH=dedede
TEST=build and confirm gpio.c can be loaded
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I39947c66de04695e5242ab1affc328894f34f9f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75520
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move I2S config from common to board.
BUG=none
TEST=Build google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I51ca902e9b0077d5d5cc9c3507d26301a0f61bc2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75513
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable drivers for SoundWire codecs and define the topology in
the devicetree for the rex0 variant with the SoundWire daughter
board connected.
+------------------+ +--------------------+
| | | Headphone Codec |
| Intel Meteor Lake| +--->|Cirrus Logic CS42L42|
| SoundWire | | | ID 0 |
| Controller | | +--------------------+
| | |
| Link 0 +----+ +-------------------+
| | | Left Speaker Amp |
| Link 1 | +--->| Maxim MAX98363 |
| | | | ID 0 |
| Link 2 +----| +-------------------+
| | |
| Link 3 | | +-------------------+
| | | | Right Speaker Amp |
+------------------+ +--->| Maxim MAX98363 |
| ID 1 |
+-------------------+
This was tested by booting the firmware and dumping the SSDT table
to ensure that all SoundWire ACPI devices are created as expected with
the properties that are defined in coreboot under \_SB.PCI0:
HDAS - Intel Meteor Lake HDA PCI device
HDAS.SNDW - Intel Meteor Lake SoundWire Controller
HDAS.SNDW.SW00 - Cirrus Logic CS42L42 - Headphone Codec
HDAS.SNDW.SW20 - Maxim MAX98363 - Left Speaker Amp
HDAS.SNDW.SW21 - Maxim MAX98363 - Right Speaker Amp
BUG=b:269497731
TEST=Verified SSDT for SNDW in the OS. Playback and recording are also
validated on google/rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3e11dc642ff686ba7da23ed76332f7f10e60fade
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73280
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FBVDD_PWR_EN signal should be inverted in its control level
on Agah v.s. Hades. The original change covered the Hades
implementation, but needs to be updated to invert for Agah. This
change can be removed once we drop support for Agah.
BUG=b:280467267
TEST=built for Hades and Agah
Change-Id: I7f90c03b8d9b859004e5c124bf0a1f7b59921c3d
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75530
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Fine tune eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 2500 cycles of cold boot successfully on all eMMC sku.
Change-Id: I82a55a1fe17aa910eb02464df463603dcbbbef05
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75459
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI DmaProperty for WLAN device. `is_untrusted` is eventually
ended up by adding DMA property _DSD which is similar to what
`add_acpi_dma_property` does for WWAN drivers, hence it makes sense to
have a unified name across different device drivers.
BUG=b:279676191
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I6d898a939aa0be31a671d2436a81c34f7a1ec030
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75460
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add 'common_config.acp_config' to the device tree, so we have the
correct pin configuration.
BUG=b:225320579
TEST=USE=fwconsole emerge-skyrim ... ; verify 'devbeep' works in
depthcharge console
TEST=Boot into ChromeOS, verify YouTube sound works with internal
speakers and headphone jack
TEST=Boot into ChromeOS, verify microphone with Google Meet
Change-Id: Ie2d79408104273d8a53214b683800fa0663c14d3
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Incorrect memory part was used in CB:74745 to generate the DRAM Strap
ID. Amend the memory_parts_used.txt and regenerate the DRAM Strap ID.
BUG=b:272746814
TEST=Generate the DRAM Strap ID.
Change-Id: I0668d7e02345610a11f9113d8bbe99a474f33f1a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
BUG=b:283477280
TEST=Able to build and boot google/rex as per Proto 2 schematics
dated 05/16.
+-----------------+------------------------------------+---------------------------+--------+
| GPIO | In Proto 1 | In Proto 2 | Impact |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_C01 | SOC_TCHSCR_RST_L | SOC_TCHSCR_RST_R_L | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_D19 | NC | EC_SOC_REC_SWITCH_ODL | Y |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E04 | HPS_INT_L | SOC_PEN_DETECT | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E17 | EN_HPS_PWR | EN_PP3300_SPARE_X | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F13 | GSPI1_SOC_MISO | GSPI1_SOC_MISO_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F21 | GPIO_F21_SPI_CS_L | SPI_SOC_CS_UWB_L_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H00 | GPIO_H00_SPI_CLK_R | SPI_SOC_CLK_UWB_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H01 | GPIO_H01_SPI_MOSI_R | SPI_SOC_DO_UWB_DI_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H02 | GPIO_H02_SPI_MISO | SPI_SOC_DI_UWB_DO_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S00 | UNNAMED_8_METEORLAKEU_I137_GPPS00 | SDW_HP_CLK_WLAN_PCM_CLK | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S01 | UNNAMED_8_METEORLAKEU_I137_GPPS01 | SDW_HP_DATA_WLAN_PCM_SYNC | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S02 | UNNAMED_8_METEORLAKEU_I137_GPPS02 | DMIC_SOC_CLK0_WLAN_PCM_OUT| N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S03 | UNNAMED_8_METEORLAKEU_I137_GPPS03 | DMIC_SOC_DATA0_WLAN_PCM_IN| N |
+-----------------+------------------------------------+---------------------------+--------+
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4a8c43b0f845d3446188b7c926e482f91e5b45aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75407
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch adds two new chromeos_*.fmd files for release and debug FSP
builds targeting rex_ec_ish.
`rex_ec_ish` variant would pack ISH firmware into the CSE boot partition
hence, the blob size is expected to increase. Creates separate flash map
layout to ensure ISH work is not impacting on the regular `rex0` project
SPI flash usage.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: Ife4663d3ccf80a928646eadaac4c9ab49ad29055
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75471
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a new variant to support the ISH enablement using
Rex platform.The idea here is to leverage the `rex0` code as much as
possible and add specific support for ISH enablement as per the hardware
schematic differences.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: I625fd0b31aed998f4e8f2d139827bc212ee8a90b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75470
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add support of variant_devtree_update() function to override
devtree settings for variant boards. Also, add CPU power limit
values for rex baseboard.
BRANCH=None
BUG=b:270664854
TEST=Built and verified power limit values as below log message
for 15W SKU on Rex board.
Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW)
(57000, 57000) PL4 (W) (114)
Change-Id: If46445157358e3e0f227e26a35b4303fc9189a4b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Restrict memory speed to 6400 MTS as per board design.
BUG=b:282164577
TEST=Verified the settings on google/rex using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3dec383c7c585b80a73089f3403011c5cda61f65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
"extern" is automatically implied with function declaration.
Change-Id: Ic40218acab5a009621b6882faacfcac800aaf0b9
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71890
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use fw_config to probe lte.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5596f3536b0a21453f89e67615acabbbf6a8409b
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75337
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to probe touchpad.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib20abac74683c670c174821b821ede461dbb0163
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Enable touchpad for Google Screebo.
BUG=b:278160238
BRANCH=none
TEST=Build and boot to Google Screebo. Verify touchpad works.
Change-Id: Ib83e5ef5ca497592f5a26aa1e85d793d06d9dd7f
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75412
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Commit f99d6700 ("mb/google/skyrim/var/winterhold: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot winterhold, dump ACPI, verify unchanged
Change-Id: Ia9982fed0fe2093d787ee9506ac5bbadd6cc03f9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75389
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit d81ee3f1 ("mb/google/skyrim/var/markarth: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot markarth, dump ACPI, verify unchanged
Change-Id: I5c1cd23c49b512f55e9e13b2164d30dfb7fb682d
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75388
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit a539893c ("mb/google/skyrim/var/frostflow: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, dump ACPI, verify unchanged
Change-Id: I3912fe1b7d3f2a07cb379928cd4f5d87100d3284
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75387
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch overrides `SaGv` FSP-M UPD to enable SaGv feature to be
able to train memory (DIMM) at different frequencies.
On all latest Intel based platforms SaGv is expected to be enabled
to support dynamic switching of memory operating frequency.
BUG=b:267879107
TEST=Able to verify SaGv is enabled with 3 work point (0, 1 and 2)
and MRC retraining takes around ~20ms extra compared to SaGv being
disabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic680bfeab4dd285c0d3916ba5e917cc12bae3284
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73534
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SKU1A C0 has no redriver, so enable SBU muxing in the SoC.
BUG=b:283044004
BRANCH=none
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: I18b4ade2c60c270855fb2e733a9201539e08d8ba
Signed-off-by: mike <mike5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Enabling BT for screebo project
BUG=b:278169273
TEST=Check whether BT can connect to Bluetooth device
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Change-Id: I0ecd62abfbe751e1036948b1490844e7e63d7f0d
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75352
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Hades uses the SODIMM, enable the smbus to see the SPD address for the
memory.
BUG=b:283138024
TEST=i2cdetect -l can see the smubs adapter.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I3912a025afaf8388d04a4b08852a84d4a2a6bf06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75399
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to probe touchscreen.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5d8129b3af3aa09e5bc31160de82d9ef7af0dd59
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ic498afcc8b8e0224f344f405e2f1ef6184df1d6b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75340
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ie40541ada508acfa5771ea800249b8a57b168e3b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75339
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, verify error no longer present in dmesg.
Change-Id: I0b87af6b2c04f9354e6f394a8f987fa660e49134
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75338
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I05a2cd5f2235702dea8fd706349ebda6a9ffa2ef
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:282912666
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Iee6a9026a4d210407350bfb7ecc8a058e7ff5c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
TEST=set the corresponding cbi bit, and saw SPI0 under sysfs
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I7099cde14cff90ad63e9164769f9913a8284a805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
According to Thermal table 0518, adjust DPTC and STT settings.
BRANCH=none
BUG=b:273636128
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id1c1884eabc1ea58148270f39eaca836ccc3fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Pujjoteen5 support WWAN 5G device, use variant.c to handle the
power on sequence.
BUG=b:279835626
TEST=Build and check WWAN 5G power on sequence.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7dc72f2c705bcb41745f4bf08bef286773fe8b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75327
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Measured the I2C frequency meets spec
1. I2C0 (TPM): 976.1 Khz
2. I2C1 (TouchScreen); 394.0 Khz
3. I2C2 (WCAM); 377.9 Khz
4. I2C3 (Audio): 390.0 Khz
5. I2C5 (Touchpad): 389.3 Khz
BUG=b:283374537
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
and check all I2C devices measurement result
Change-Id: If6e3a4a2b1ac642561015a290e6579238c3c2b1b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Set the DmaProperty in the device's _DSD so that the OS can treat the
device as untrusted.
BUG=b:278310256
TEST=cat /sys/bus/pci/devices/<wifi>/untrusted == 1
iperf3 -c <iperf3-server> -t 60 (No performance regressions seen)
Change-Id: I06369a19afa5b881b26f5c1eb243e2db41a9bb36
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75095
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Disable backlight before turning on bridge, otherwise the bridge will
initialize failed.
Fixes: d5c1e1(mb/google/corsola: Add support for MIPI panel)
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7d10bf9e8675b2fb03bfd1e294af66207b9b0620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75354
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
BUG=b:278156430
TEST=verify the fingerprint on screebo
Change-Id: I986e470b28145f7b17427e794055929a4283c721
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75287
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The upstream kernel privacy screen driver uses HID GOOG0010 to look for
firmware node to use. This method is used on other boards, e.g. redrix.
See: drivers/platform/chrome/chromeos_privacy_screen.c in linux sources.
Update jinlon gfx ACPI node to work with that.
BUG=b:279092050
TEST=privacy protection screen works with 5.15 and 4.19 kernels
Change-Id: Icba41e7f2be7292f713fea10dbe69b3ca128bde7
Signed-off-by: Kornel Dulęba <korneld@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75289
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Disable unused gpio for LTE daughter board, WFC and stylus.
BUG=b:277148122
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I6cc61321cd96a10dd34ff6cd9fcabe85a64bbfa9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75293
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:281928906
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Ia5193d3ab3d654f25d519ad9a954f2ca8a15a978
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75152
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@google.com>
|
|
GC6 - Low power mode for system idle on Nvidia GPU
In GC6I Before ramp of PEXVDD:
Deassert FBVDDQ Enable, no delay is needed before or after.
In GC6O After ramp of PEXVDD:
Assert FBVDDQ Enable, no delay is needed before or after.
BUG=b:280467267
TEST=built for Hades and Agah, tested on Agah
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I0277772b1d2f6f4e6a3f74b92035e8b36f2670ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75302
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables stylus support by configuring the "GPP_D08" irqs for
rex SoC. This allows the SoC to detect a stylus device, when in use.
However stylus is not a wake up source for the rex.
BUG=b:282256460
Test=Stylus is detected on proto1 device.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I84a71aa664698e105b738f8680d0a4751ca1fc72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The SPD format in the APCB has changed for Phoenix, and the injection
tool 'apcbtool' needs to be updated to match. Until this happens, the
APCB will be built containing the correct SPD.
BUG=b:281983434
TEST=Build
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If575f98511c796e93c5a12cd450a3a7985e39806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Pujjoteen5 support WWAN 5G device, add GPIO setting for WWAN 5G device
BUG=b:281943398
TEST=Build and check serial log
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ie2e0ea34c54a453645d626f892f50654ef5064ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75195
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pujjoteen5 support WWAN 5G device, enable PCIe port 3 for WWAN 5G device
BUG=b:281943398
TEST=Build and boot on pujjo
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I6d2e8eaecae968ed51095d9497beab492ba7e0c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:280843816
TEST=builds
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I55a85335a34eee227abb6ff355719f7ca2cbf04a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Use AUDIO PROBE to determine speaker amp config, set SOF driver
profile accordingly.
TEST=build/boot Win11 on Delbin and Drobit, verify correct audio profile
selected, drivers loaded and functional.
Change-Id: I13d787cb5ccb74d2774151ccd5deeb45b3364319
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Taniks uses a 4-channel output config, rather than 2-channel.
Update the SOF speaker topology accordingly.
TEST=build/boot Win11 on taniks, verify speaker output functional.
Change-Id: I3c08b12b11464dcada014289174e0cc468d1c39d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
By moving certain FW UI assets from RO to RW sections, 4 MiB is
sufficient for RO section. Split the resultant available 4 MiB equally
between 2 RW sections. This will help in getting to 16 MiB SPI flash for
the mainboard.
BUG=b:281567816
TEST=Build Myst BIOS image with the updated layout.
Cq-Depend: chromium:4519688
Change-Id: I09948ceac0a6a1cb109322fc4856b8b486318664
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75184
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
