| Age | Commit message (Collapse) | Author |
|---|
|
BUG=b:283477280
TEST=Able to build and boot google/rex as per Proto 2 schematics
dated 05/16.
+-----------------+------------------------------------+---------------------------+--------+
| GPIO | In Proto 1 | In Proto 2 | Impact |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_C01 | SOC_TCHSCR_RST_L | SOC_TCHSCR_RST_R_L | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_D19 | NC | EC_SOC_REC_SWITCH_ODL | Y |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E04 | HPS_INT_L | SOC_PEN_DETECT | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_E17 | EN_HPS_PWR | EN_PP3300_SPARE_X | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F13 | GSPI1_SOC_MISO | GSPI1_SOC_MISO_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_F21 | GPIO_F21_SPI_CS_L | SPI_SOC_CS_UWB_L_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H00 | GPIO_H00_SPI_CLK_R | SPI_SOC_CLK_UWB_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H01 | GPIO_H01_SPI_MOSI_R | SPI_SOC_DO_UWB_DI_STRAP_R | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_H02 | GPIO_H02_SPI_MISO | SPI_SOC_DI_UWB_DO_STRAP | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S00 | UNNAMED_8_METEORLAKEU_I137_GPPS00 | SDW_HP_CLK_WLAN_PCM_CLK | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S01 | UNNAMED_8_METEORLAKEU_I137_GPPS01 | SDW_HP_DATA_WLAN_PCM_SYNC | N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S02 | UNNAMED_8_METEORLAKEU_I137_GPPS02 | DMIC_SOC_CLK0_WLAN_PCM_OUT| N |
+-----------------+------------------------------------+---------------------------+--------+
| GPP_S03 | UNNAMED_8_METEORLAKEU_I137_GPPS03 | DMIC_SOC_DATA0_WLAN_PCM_IN| N |
+-----------------+------------------------------------+---------------------------+--------+
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4a8c43b0f845d3446188b7c926e482f91e5b45aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75407
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch adds two new chromeos_*.fmd files for release and debug FSP
builds targeting rex_ec_ish.
`rex_ec_ish` variant would pack ISH firmware into the CSE boot partition
hence, the blob size is expected to increase. Creates separate flash map
layout to ensure ISH work is not impacting on the regular `rex0` project
SPI flash usage.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: Ife4663d3ccf80a928646eadaac4c9ab49ad29055
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75471
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a new variant to support the ISH enablement using
Rex platform.The idea here is to leverage the `rex0` code as much as
possible and add specific support for ISH enablement as per the hardware
schematic differences.
BUG=b:284254353
TEST=Able to build google/rex_ish_ec board and boot on target hardware.
Change-Id: I625fd0b31aed998f4e8f2d139827bc212ee8a90b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75470
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add support of variant_devtree_update() function to override
devtree settings for variant boards. Also, add CPU power limit
values for rex baseboard.
BRANCH=None
BUG=b:270664854
TEST=Built and verified power limit values as below log message
for 15W SKU on Rex board.
Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW)
(57000, 57000) PL4 (W) (114)
Change-Id: If46445157358e3e0f227e26a35b4303fc9189a4b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Restrict memory speed to 6400 MTS as per board design.
BUG=b:282164577
TEST=Verified the settings on google/rex using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3dec383c7c585b80a73089f3403011c5cda61f65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
"extern" is automatically implied with function declaration.
Change-Id: Ic40218acab5a009621b6882faacfcac800aaf0b9
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71890
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use fw_config to probe lte.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5596f3536b0a21453f89e67615acabbbf6a8409b
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75337
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to probe touchpad.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Ib20abac74683c670c174821b821ede461dbb0163
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Enable touchpad for Google Screebo.
BUG=b:278160238
BRANCH=none
TEST=Build and boot to Google Screebo. Verify touchpad works.
Change-Id: Ib83e5ef5ca497592f5a26aa1e85d793d06d9dd7f
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75412
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Commit f99d6700 ("mb/google/skyrim/var/winterhold: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot winterhold, dump ACPI, verify unchanged
Change-Id: Ia9982fed0fe2093d787ee9506ac5bbadd6cc03f9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75389
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit d81ee3f1 ("mb/google/skyrim/var/markarth: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot markarth, dump ACPI, verify unchanged
Change-Id: I5c1cd23c49b512f55e9e13b2164d30dfb7fb682d
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75388
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit a539893c ("mb/google/skyrim/var/frostflow: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, dump ACPI, verify unchanged
Change-Id: I3912fe1b7d3f2a07cb379928cd4f5d87100d3284
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75387
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch overrides `SaGv` FSP-M UPD to enable SaGv feature to be
able to train memory (DIMM) at different frequencies.
On all latest Intel based platforms SaGv is expected to be enabled
to support dynamic switching of memory operating frequency.
BUG=b:267879107
TEST=Able to verify SaGv is enabled with 3 work point (0, 1 and 2)
and MRC retraining takes around ~20ms extra compared to SaGv being
disabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic680bfeab4dd285c0d3916ba5e917cc12bae3284
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73534
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SKU1A C0 has no redriver, so enable SBU muxing in the SoC.
BUG=b:283044004
BRANCH=none
TEST=Voltages are correct on the C0 and C1 AUX bias pins
Change-Id: I18b4ade2c60c270855fb2e733a9201539e08d8ba
Signed-off-by: mike <mike5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Enabling BT for screebo project
BUG=b:278169273
TEST=Check whether BT can connect to Bluetooth device
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Change-Id: I0ecd62abfbe751e1036948b1490844e7e63d7f0d
Signed-off-by: qinwentao <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75352
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Hades uses the SODIMM, enable the smbus to see the SPD address for the
memory.
BUG=b:283138024
TEST=i2cdetect -l can see the smubs adapter.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I3912a025afaf8388d04a4b08852a84d4a2a6bf06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75399
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to probe touchscreen.
BUG=b:283199751
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I5d8129b3af3aa09e5bc31160de82d9ef7af0dd59
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ic498afcc8b8e0224f344f405e2f1ef6184df1d6b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75340
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ie40541ada508acfa5771ea800249b8a57b168e3b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75339
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, verify error no longer present in dmesg.
Change-Id: I0b87af6b2c04f9354e6f394a8f987fa660e49134
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75338
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I05a2cd5f2235702dea8fd706349ebda6a9ffa2ef
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:282912666
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Iee6a9026a4d210407350bfb7ecc8a058e7ff5c24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
TEST=set the corresponding cbi bit, and saw SPI0 under sysfs
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I7099cde14cff90ad63e9164769f9913a8284a805
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
According to Thermal table 0518, adjust DPTC and STT settings.
BRANCH=none
BUG=b:273636128
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id1c1884eabc1ea58148270f39eaca836ccc3fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Pujjoteen5 support WWAN 5G device, use variant.c to handle the
power on sequence.
BUG=b:279835626
TEST=Build and check WWAN 5G power on sequence.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7dc72f2c705bcb41745f4bf08bef286773fe8b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75327
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Measured the I2C frequency meets spec
1. I2C0 (TPM): 976.1 Khz
2. I2C1 (TouchScreen); 394.0 Khz
3. I2C2 (WCAM); 377.9 Khz
4. I2C3 (Audio): 390.0 Khz
5. I2C5 (Touchpad): 389.3 Khz
BUG=b:283374537
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
and check all I2C devices measurement result
Change-Id: If6e3a4a2b1ac642561015a290e6579238c3c2b1b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Set the DmaProperty in the device's _DSD so that the OS can treat the
device as untrusted.
BUG=b:278310256
TEST=cat /sys/bus/pci/devices/<wifi>/untrusted == 1
iperf3 -c <iperf3-server> -t 60 (No performance regressions seen)
Change-Id: I06369a19afa5b881b26f5c1eb243e2db41a9bb36
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75095
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Disable backlight before turning on bridge, otherwise the bridge will
initialize failed.
Fixes: d5c1e1(mb/google/corsola: Add support for MIPI panel)
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I7d10bf9e8675b2fb03bfd1e294af66207b9b0620
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75354
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
BUG=b:278156430
TEST=verify the fingerprint on screebo
Change-Id: I986e470b28145f7b17427e794055929a4283c721
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75287
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The upstream kernel privacy screen driver uses HID GOOG0010 to look for
firmware node to use. This method is used on other boards, e.g. redrix.
See: drivers/platform/chrome/chromeos_privacy_screen.c in linux sources.
Update jinlon gfx ACPI node to work with that.
BUG=b:279092050
TEST=privacy protection screen works with 5.15 and 4.19 kernels
Change-Id: Icba41e7f2be7292f713fea10dbe69b3ca128bde7
Signed-off-by: Kornel Dulęba <korneld@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75289
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Disable unused gpio for LTE daughter board, WFC and stylus.
BUG=b:277148122
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I6cc61321cd96a10dd34ff6cd9fcabe85a64bbfa9
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75293
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generate the RAM ID for Samsung K3KL6L60GM-MGCT.
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 6 (0110)
BUG=b:281928906
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Ia5193d3ab3d654f25d519ad9a954f2ca8a15a978
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75152
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@google.com>
|
|
GC6 - Low power mode for system idle on Nvidia GPU
In GC6I Before ramp of PEXVDD:
Deassert FBVDDQ Enable, no delay is needed before or after.
In GC6O After ramp of PEXVDD:
Assert FBVDDQ Enable, no delay is needed before or after.
BUG=b:280467267
TEST=built for Hades and Agah, tested on Agah
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I0277772b1d2f6f4e6a3f74b92035e8b36f2670ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75302
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables stylus support by configuring the "GPP_D08" irqs for
rex SoC. This allows the SoC to detect a stylus device, when in use.
However stylus is not a wake up source for the rex.
BUG=b:282256460
Test=Stylus is detected on proto1 device.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: I84a71aa664698e105b738f8680d0a4751ca1fc72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The SPD format in the APCB has changed for Phoenix, and the injection
tool 'apcbtool' needs to be updated to match. Until this happens, the
APCB will be built containing the correct SPD.
BUG=b:281983434
TEST=Build
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If575f98511c796e93c5a12cd450a3a7985e39806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Pujjoteen5 support WWAN 5G device, add GPIO setting for WWAN 5G device
BUG=b:281943398
TEST=Build and check serial log
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ie2e0ea34c54a453645d626f892f50654ef5064ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75195
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pujjoteen5 support WWAN 5G device, enable PCIe port 3 for WWAN 5G device
BUG=b:281943398
TEST=Build and boot on pujjo
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I6d2e8eaecae968ed51095d9497beab492ba7e0c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:280843816
TEST=builds
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I55a85335a34eee227abb6ff355719f7ca2cbf04a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Use AUDIO PROBE to determine speaker amp config, set SOF driver
profile accordingly.
TEST=build/boot Win11 on Delbin and Drobit, verify correct audio profile
selected, drivers loaded and functional.
Change-Id: I13d787cb5ccb74d2774151ccd5deeb45b3364319
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Taniks uses a 4-channel output config, rather than 2-channel.
Update the SOF speaker topology accordingly.
TEST=build/boot Win11 on taniks, verify speaker output functional.
Change-Id: I3c08b12b11464dcada014289174e0cc468d1c39d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
By moving certain FW UI assets from RO to RW sections, 4 MiB is
sufficient for RO section. Split the resultant available 4 MiB equally
between 2 RW sections. This will help in getting to 16 MiB SPI flash for
the mainboard.
BUG=b:281567816
TEST=Build Myst BIOS image with the updated layout.
Cq-Depend: chromium:4519688
Change-Id: I09948ceac0a6a1cb109322fc4856b8b486318664
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75184
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
copy from dibbi since taranza base on dibbi,this is only for first
initial configuration, will update the more setting afterward.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia319f65897c0fea2f0558c20a5bc36bb6fbaea96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
BUG=b:277664211
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I6bbb67ccdd8ebc21719921d00320907f8dbb285f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74933
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds support for variant specific chip config update similar
to commit 061a93f93d2 ("mb/google/brya: Add variant specific soc chip config update").
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I60a4042cba608fd527527af9340ec0215f3086ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75046
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
add initial devicetree config for screebo
BUG=b:276814951
TEST=emerge-rex coreboot
Change-Id: Ie64d0e50ec22b3e363597af64eb723ef1f86dfa8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The detachable Starmie will use MIPI panels, which require reading
serializable data from the CBFS. So we add MIPI panel support to the
display configuration and align the configuration sequence with the
panels that use MIPI bridges.
The PMIC Datasheet:
TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:275470328
BRANCH=corsola
TEST=emerge-corsola coreboot chromeos-bootimage and display normally
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I6f079e54f0317ff2f685f0e3834ebd1ceb8e9fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add wifi sar table for uldren
BUG=b:279679700
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I9e3d7a06beb673b204f2dfe8e7beb919730aa885
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:278022971
TEST=verified on screebo
Change-Id: I16f1d66ca7f885120358eb2a2d3c6fb111319f11
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75173
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When using a 32-MiB ROM chip, the ABL leaves the SPI flash in 4-byte
addressing mode, so ensure the driver exits that mode for regular
operation.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9a846be743a65ffe5b3ef94e20e0b5fc5e273961
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
TPM IRQ should be A20 not A13. RAM table is correct.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I82a709cc280288d612c65697b8da3c4274d4cd3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75191
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow schematic to correct I2C bus.
BUG=b:282164589
TEST=able to boot up
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I277e5190302c98dbce809d09c1a32fac758aa8e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach.
TEST=build/boot google/parrot, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: Ic164244eceb52221653bd60f7217f9a09e38c1b6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75180
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the touchpad HID/CID/HRV to allow coolstar's crostouchpad
Windows drivers to properly attach. Change the interrupt type
from EDGE to LEVEL.
TEST=build/boot google/butterfly, verify touchpad functional under
both Windows 10/11 and Linux, verify Windows overlay driver
correctly remaps top row keys.
Change-Id: I971795becfb05fb42921ff6f40a20892f4f5654a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use board-specific ASL for PS2-attached trackpad rather than the EC/SIO
default, so that Windows installs a multitouch-capable driver rather
than the standard PS2 mouse driver.
TEST=build/boot Win11 on google/stout, verify trackpad is multitouch
capable.
Change-Id: Id93bbe53f35b1e2c35e36d8175889786b9f5de8b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75176
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on touchscreen product spec.
For uldren variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:279989974
TEST=Build and boot to OS in uldren. Touch screen is workable.
Change-Id: Ib1b1ce80aa1dd8c312e3663fc50c9e9f53cc07fe
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74835
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
This signal isn't functionally being used and is causing leakage
during suspend. Set it to NC.
BUG=b:279762779
TEST=builds. WWAN functional.
Change-Id: I93f2b0a781e250678280b57e4ab1d80ef27ff460
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Small typo in brask/gma-mainboards-ads
Should be brask/gma-mainboards.ads
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds
Change-Id: I9800870dcef13a3e16f6235137e79234a5e6bf83
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75052
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the gothrax variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.).
BUG=279614675
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GOTHRAX
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I129e4a55e4b87091e425a45392024d04f3977c79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The boxy removed the APW8738BQBI-TRG and
"disable_external_bypass_vr" should be set to "1" to disable
BUG=b:271407334
TEST=emerge-dedede coreboot
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: Ic6667e93de41e84f67363ab7554fe755fe50684a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74889
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create overridetree and GPIO config based on latest schematic:
1. Update PCIe ports
2. Update USB ports
3. Remove unused I2Cs
4. Remove unused peripherals (SD card, eDP, speakers)
5. Add LAN
6. Thermal policy for updated temp sensors
BUG=b:277529068
BRANCH=dedede
TEST=build
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Change-Id: I5a155ebca50dbd5bdb046713ebabbee395361273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74626
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
For the sequenced controlled shutdown path, there's a 10ms delay
after the PEXVDD rail is disabled to permit discharge needed on
Agah/Proxima.
This can be dropped to 3ms for Hades designs Proto0 and forward.
Once Agah board is dropped, "if CONFIG" can be cleaned up/removed.
BUG=b:271167335
TEST=builds
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I8a0d62ec76caff861adce2d6c0ba2d4e4064affa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75051
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All other boards use MAINBOARD_ prefix instead of board name.
Change-Id: I97d9d28963c97e780156d75b39deac069028866a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I4d34e5c094440dad4a6ab9adc67d3da6b71ac2bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74514
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: If4b7c2b94e0fec84831740336ccdbea0922ffbfe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74513
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: I3881c152663a038833d8126d7f24f2a6688426d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74515
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The STA_HIMAX83102_J02 and STA_ILI9882T panel will be used for Starmie,
enable these two panels config for it.
BUG=b:272425116
BRANCH=corsola
TEST=build starmie and check the cbfs include the panels
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I1dd696dd6a84d9606e4b9a2d4884dd70a6df9161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74200
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG item for FP sensor init and conditionally init
the GPIOs based on whether we're using a SPI or UART FP sensor.
BUG=b:276939271
TEST=builds
Change-Id: I9815bd17df1d15f73529beb15d08cde1ef90efad
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG item for eMMC/NVMe support and address the init
of the lanes based on said config.
BUG=b:278877257
TEST=builds
Change-Id: Id6452f497cf78549b7d6126f1b55cd6d45b403c3
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74957
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Mark Hasemeyer <markhas@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Allow different gma-mainboards configs for different baseboards
as they support varying display interfaces. Set Brya to eDP only
and Brask to HDMI only.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on both brya and brask varaints
Change-Id: Iaf3f35b009d53e50723e4aa82c0f4932783f9bb9
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Denote the correct value of ACPI _PLD for USB ports.
The horizontal position of port C0 is incorrectly labelled.
+----------------+
| |
| Screen |
| |
+----------------+
C0 | | A0
| | C1
| |
+----------------+
BUG=b:216490477
TEST=emerg-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id9ed435ca0af131e3bb4538701fc97d78146899f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74366
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update eMMC DLL settings based on Uldren board.
BUG=b:280120229
TEST=executed 10 cycles of cold boot successfully
Change-Id: I46e2f9df0e82e66fa3ae32aa87b4bcf30d5737ab
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree to support G7500 touchscreen.
BUG=b:273791621
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and check touchscreen function
Change-Id: I3b63b1bb45275ad7eef8799dcff27f264739c258
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: Id5b0fa96ca8d86ddf20d808f5107a43ad2d0a1e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I47ec05aa87e4e7c02b19817b2f703eca492008e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add DDR DQ map config for screebo
BUG=b:276814951,b:272218757
TEST=emerge-rex coreboot
Change-Id: I993ae4024689b9cedbea247689a760bd83cd0d45
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74961
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Add variant makefile to support including the memory folder for Myst.
BUG=b:273383819
TEST=Builds in chromium with blobs
Change-Id: I03b0cd91dd66f357b15522da36f5118867b6b14c
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74964
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the OEM ID from CBI to determine the correct OEM board name.
ID mapping taken from ChromeEC source, branch firmware-fizz-10139.B.
TEST=build/boot multiple fizz variants, check that board name reported
correctly in SMBIOS tables.
Change-Id: I06251974ac73570b911920ed566a175e8e733710
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Override SMBIOS product name with sub-variant name based on board SKU.
TEST=build/boot multiple nami variants, verify SMBIOS product name
reports correctly.
Change-Id: I2125bfb6436469405378f9c983d7cfcb2f85f916
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
DSM (Dynamic Speaker Management) uses calibration parameters stored in
a VPD (Vital Product Data) FMAP region to configure the audio output
via an ACPI _DSD table. This has no dependency on a ChromeOS, and can
be used by Linux/Windows drivers if appropriately configured.
Remove the dependency of DSM_CALIB (and the calibration file) on
CHROMEOS and replace it with VPD, so that non-CHROMEOS builds
can utilize this feature as well. Move files from underneath
vc/google/chromeos to underscore the point.
TEST=build/boot google/nightfury, dump ACPI, verify DSM calibraton
parameters present in _DSD table.
Change-Id: I643b3581bcc662befc9e30736dae806f94b055af
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Only expand these strings in lib/identity.o.
Change-Id: I8732bbeff8cf8a757bf32fdb615b1d0f97584585
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The patch disables Tccold Handshake to prevent possible display
flicker issue for marasov board. Please refer to Intel doc#723158
for more information.
BUG=b:279117758
BRANCH=firmware-brya-14505.B
TEST=Boot to OS on marasov.
Signed-off-by: Frank Chu <Frank_Chu@pegatron.corp-partner.google.com>
Change-Id: I286e88e5bec240d64e6c801648f6483ad2b0939c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74931
Reviewed-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
variant_board_sku() is missing dependences in order to work correctly
in romstage. Rather than more intrusive rework as its use is limited,
move the FPMCU early GPIO init back to ramstage. We still meet
sufficient power off time to fully power cycle the MCU.
BUG=b:245954151
TEST=Confirmed FPMCU is still functional on Nami and FP tests all pass
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: Ia428ec5aec1a0438e91bc48903bda043046b740e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74695
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The image processing unit/GMM and xDCI are not used on octopus boards;
additionally, enabling xDCI can cause some problems with USB ports in
both booting from the payload and in the OS.
Change-Id: I1ee99b5c45881a4cf3624bf487bc9d83fb3d07a1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on wyvern variant, verify headphone output
and microphone functional under Windows using coolstar's SOF drivers.
Change-Id: I421c070eac321c2fc160b8f26868bcb1ec13001e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74815
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several volteer variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I62a96149cec9eeb7b2da8a2337083969a1b0fce0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74816
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on banshee and osiris variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I12614b85f9779cc40d83a9c868cc46b110f26af6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74817
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add all SOF chip drivers to baseboard and use FW_CONFIG to determine
the correct option, to ensure the correct audio config is passed to the
SOF OS drivers.
TEST=build, boot Windows on several dedede variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: I9452b11af614d8727aa8dd448e37f7a06faa450d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74818
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Tuning i2c frequency ,timing ,Waveform meet to SPEC
i2c frequency :
I2C0=>399.8khz / Setup Time:1765ns / Hold Time:82.35ns.
I2C1=>390.4khz / Setup Time:1.788us / Hold Time:70.58ns.
I2C3=>308.7khz / Setup Time:1.482us / Hold Time:0.4us.
I2C5=>390.8khz / Setup Time:1.218us / Hold Time:0.405us.
BUG=b:275061994
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot,
EE check OK with test FW and TP function is normal.
Change-Id: I5b77cd3fd3ff00804f1b8dd5828dc831a9732566
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74880
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
We have largely dropped from filling in mainboard_ops.name
as unnecessary. A common place should be decided where or if
this information is added in the console log.
Change-Id: I917222922560c6273b4be91cd7d99ce2ff8e4231
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add SOF chip driver entries for all variants, so that the correct audio
config is passed to the OS drivers.
TEST=build, boot Windows on several hatch variants, verify audio
functional under Windows using coolstar's SOF drivers.
Change-Id: Ie791fa873fc7bbab84644f5ea5743bdcdc124908
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
The image processing unit (Iunit) and SoC UARTS are not used on any
reef boards.
Change-Id: Iacdf93b4952cbc63fc465f07d440463106527b8d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
It's not particularly useful to end users, and shows up as an unknown
PCI device under Windows Device Manager.
TEST=build reef, boot Windows, verify unknown PCI device no longer
present in Device Manager.
Change-Id: Ie8ec46e2e07b6635bfe9766812ce08b866c71d66
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add rules to inject the variant specific SPD binaries into APCB.
BUG=b:273383819
TEST=Build Myst BIOS image. Currently no APCB is present. So no SPD is
injected into APCB.
Change-Id: Ic511cdc4fe0989c9abc0cd0531cc0cae40f8dc34
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74746
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Generate the RAM Strap IDs based on the initial memory configuration.
BUG=b:272746814
TEST=Build Myst BIOS image.
Change-Id: I8a4fe9a41f101ac10391756f1b815220c8b98612
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
There is no platform-level implementation for USB port power management
in various sleepstates. The mainboards changed here never evaluate the
set GNVS variables S3U0, S3U1, S5U0 and S5U1 in ASL or in their SMI
handlers.
Change-Id: Ia1bc5969804a7346caac4ae93336efd9f0240c87
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
|
|
Change-Id: I634af65cd41e0d70e673d550ed8063abc6eea6d4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Add data.vbt files for all variants supported by current volteer
recovery image. Several boards use the same VBT, so place the "common"
VBT under the baseboard directory and set it as the default.
For variants with a unique VBT, override the default and use the file in
their respective variant directory. Select INTEL_GMA_HAVE_VBT for all
variants which have a VBT file.
TEST=build/boot various volteer variants
Change-Id: I728ab81938c78f600ff8931a8073d1f7de152c09
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74852
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Camera LED will blink several times as sensor is being probed during kernel boot.
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:274634319
TEST=Build and boot on Craask. Verify & observe Camera LED blinking behavior.
Change-Id: I78ed5efe1e2c071d817c1e0455271886e89e63c7
Signed-off-by: Jimmy Su <jimmy.su@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74728
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add functionality to ensure that the FPMCU is power cycled long enough
on boot to ensure proper reset.
This solution relies solely on coreboot to sequence the power and reset
signals appropriately (150ms on boot).
-Confirmed power is off for 150ms on boot.
-Confirmed RCC_CSR of FPMCU indicates power cycle occurred.
-Confirmed reset is de-asserted approx 3ms after power application
(target >2.5ms)
BUG=b:245954151
TEST=Confirmed FPMCU is still functional on Nami and timings are
as expected.
Change-Id: I0a23bda96bc2ea90be81a2310605f75c55c0a839
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add functionality that allows a variant SKU to have a specific set of
GPIO configs in romstage (modeled after the existing one in
ramstage)
BUG=b:245954151
TEST=builds
Change-Id: I593a23951306908fadc00e6bc8d9d310f09c5e4b
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
