| Age | Commit message (Collapse) | Author |
|---|
|
Change config option selection from "config xyz default y" to "select
xyz" if the config option has no dependencies.
BUG=None
BRANCH=None
TEST=Verified that config option selection remains unchanged.
Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18400
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Since we are not using gpio regulators on reef anymore, remove the
selection from Kconfig as well.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18399
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Move code common code from each variant's mainboard.asl into
common ACPI code for all variants (like google/auron). This also
adds the _PRW method for the LID0 device for falco and peppy, which
omitted the function when they were originally upstreamed.
See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device
Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18368
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
eve is based on Kabylake SoC hence select the appropriate
config.
Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18314
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
poppy is based on Kabylake SoC hence select the appropriate
config.
Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18313
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for generating digitizer node in SSDT using wacom i2c
driver.
BUG=None
BRANCH=None
TEST=Verified that the node shows up in SSDT.
Change-Id: If7e1e2463778c2ff7263eff995def149457edcde
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18373
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the newly added SPI SSDT generator for adding FPC device.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully. Verified that the SSDT entry matches the
entry in mainboard.asl
Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18343
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Create the initial Sand variant which refers to the Reef.
Sand is APL board that derives from reference board Reef.
BRANCH=master
BUG=chrome-os-partner:62200
TEST=Build (as initial setup)
Signed-off-by: YH Lin <yueherngl@chromium.org>
Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625
Reviewed-on: https://review.coreboot.org/18324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change touchpad HID to use with the Google Centroiding Touchpad driver.
BUG=chrome-os-partner:61088
TEST=`emerge-eve coreboot`
Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/18359
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Poppy doesn't support 8042 keyboard. Select
NO_FADT_8042 to disable 8042 in FADT header.
Kernel will not try to access 8042 region
if 8042.FADT=0
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18311
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update DPTF parameters based on thermal team test result.
1. Update TSR2 trigger points.
TSR2 passive point: 70, critical point: 90
2. Set PL2 Max to 15W.
BUG=chrome-os-partner:61383
BRANCH=reef
TEST=build, boot on snappy, and verified by thermal team
Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18318
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Performance degradation seen with current PL1 throttling rate as 8
seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1
throttling rate to 15 seconds, fps score improved.
BUG=chrome-os-partner:60038
BRANCH=reef
TEST=Built and tested on electro system
Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
|
|
There will be more follow-up changes.
BUG=chrome-os-partner:62377
BRANCH=None
TEST=emerge-scarlet coreboot libpayload
Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c
Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a
Original-Signed-off-by: philipchen <philipchen@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433039
Original-Commit-Ready: Philip Chen <philipchen@chromium.org>
Original-Tested-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18296
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Reef is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18277
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Eve is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The WAK_STS bit is not set in a wake from G3, so the check for this
bit needs to only be done when checking for a wake from S3.
This change correctly enables the keyboard backlight in wake from G3
and only does not enable it during a wake from S3.
BUG=chrome-os-partner:58666
TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard
backlight turns on like it does when waking from S5. Also force enter
hibernate with Alt+VolumeUp+H and then power back up and ensure that
the keyboard backlight is enabled when booting.
Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18280
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When guado/rikku/tidus were rolled into jecht, an error was
made in set_power_led() as guado/rikku set the polarity
differently than tidus. Fix the power LED for guado/rikku
by setting the polarity correctly.
Test: boot guado/rikku and observe proper function of power LED
under S0, S3, and S5 power states.
Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18249
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reason for revert:
Pyro has two touchscreen sources: WACOM/ELAN.
It will not have both touchscreen IC in one system at the same time.
So the "probed" property of WACOM i2c device is mandatory to set for kernel
to know whether it exists before driver initializes it.
Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF
will be invoked to set GPIO#152 low to cut off power.
BUG=chrome-os-partner:62371
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74
this is required for poppy board as well.
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=None
BRANCH=None
TEST=play test sound in OS over internal speaker
Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18282
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:62110
BRANCH=reef
TEST=Apply new firmware to evaluate Octane benchmark score.
Change-Id: I51734051586753677129314b5273fb275c74f5d2
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/18283
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
That status isn't needed and making it non-static helps gcc 4.9.2 (or
any compiler that insists on "standard C" behaviour with global const
initializers)
Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18266
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Apollolake boards should use DMIC-4ch configuration in Kernel side and
use CaptureChannelMap in userspace to distinguish boards with different
number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will
not be required and hence removed.
BUG=chrome-os-partner:60827
TEST=Verify internal mic capture
TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works
Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/18252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
EC sets the logic level based on outstanding wake events. When GPIO_22
is configured as a level triggered interrupt, the events are not
cleared from the interrupt handler. Hence, we'd just be re-signalling
over and over causing an interrupt storm upon lid open. So, GPIO_22
needs to be configured as EDGE_SINGLE instead of LEVEL.
BUG=chrome-os-partner:62458
TEST=Lid close/open. check CPU usage using top. It should
not show 70% CPU usage.
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a
Reviewed-on: https://review.coreboot.org/18267
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Export PowerResource for WDT touchscreen device.
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Compiles successfully.
Change-Id: Icc5be170353753201d3571c39b50e29424d4d6d3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18240
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. For ELAN, export reset GPIO as well as PowerResource
2. For WCOM, export PowerResource
BUG=chrome-os-partner:62311, chrome-os-partner:60194,
chrome-os-partner:62371
BRANCH=reef
TEST=Verified that touchscreen works on pyro with WCOM device on
power-on as well as after suspend/resume.
Change-Id: I0306e24e19bf821cd3e08fdacc0d78b494c9a92f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18239
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Linux kernel expects that power management with ACPI should always be
handled using PowerResource. However, some kernel drivers (e.g. ELAN
touchscreen) check to see if reset gpio is passed in by the BIOS to
decide whether the device loses power in suspend. Thus, until the kernel
has a better way for drivers to query if device lost power in suspend,
we need to allow passing in of GPIOs via _CRS as well as exporting
PowerResource to control power to the device.
Update mainboards to export reset GPIO as well as PowerResource for
ELAN touchscreen device.
BUG=chrome-os-partner:62311,chrome-os-partner:60194
BRANCH=reef
TEST=Verified that touchscreen works on power-on as well as after
suspend-resume.
Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18238
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during
standby states S3/S0ix. This causes leakage of power. To reduce the
leakage, we have to pull these lines high during S3/S0ix. This is
done by programming the IOSSTATE to HIz. Also note that we are using
the internal pull ups to keep at SOC at 1.8V and the I2C lines are
not floating.
BUG=chrome-os-partner:62428,chrome-os-partner:61651
TEST=Enter S3/S0ix. Measure trackpad power. It should be less
than 4mW. Also I2c lines should be pulled high in S3/S0ix.
Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
In order to pass type A USB2 eye diagram,
USB2 port#0/#1 PHY register will need to be overridden.
port#0:
PERPORTPETXISET = 7
PERPORTTXISET = 1
IUSBTXEMPHASISEN = 3
PERPORTTXPEHALF = 0
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
IUSBTXEMPHASISEN = 3
PERPORTTXPEHALF = 0
BUG=chrome-os-partner:59491
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I8e67a6f0192d1c0abf6ec4926c2a17e44c818948
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Wacom touchscreen is i2c hid device and it's the device that always
exists.
So no need to set "probed" property for it.
BUG=chrome-os-partner:61513
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I27fe18ceadd03029b826e0237f80132eda1089b0
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18227
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Follow i2c-hid spec definition, level trigger interrupt is required
for i2c-hid device.
BUG=chrome-os-partner:61513
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: Ia825bd0c898e71e2ee2bf411f117a49a8fb411b6
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18217
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=chrome-os-partner:62206
BRANCH=none
TEST=plug in a charger to either port and see charge status updated to
indicate charging in the power_supply_info tool and the Chrome OS UI.
Change-Id: Ia6f63ac719b739326d313f657a68005c32f45b8d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18209
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. Update DPTF CPU/TSR1 passive trigger points.
CPU passive point: 80
TSR1 passive point: 46
2. Update DPTF TRT Sample Period
TSR1: 8s
BUG=chrome-os-partner:62133
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I8fcf750ac17b8894ed3c8704eec62f5071d9cf24
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18174
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The same GPIOs are used on both platforms, definitions are added an a
new .h to make it easier to re-use them across the code.
BRANCH=none
BUG=chrome-os-partner:51537
TEST=panel backlight still enabled on Gru as before. The rest of the
GPIOs are used in the upcoming patches.
Change-Id: I54ef3e8dd79670bdb037baeec91430113d11bcc1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c58788026f28af52c650da0159b93d97269ca4a9
Original-Change-Id: I1a6c5b5beb82ffcc5fea397e8e9ec2f183f4a7e0
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/346219
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/18176
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update the DPTF parameters based on thermal test result.
(ZHT_DPTF_EVT2_v0.4_20170120.xlsx)
1. Update DPTF TSR1 passive trigger point.
TSR1 passive point: 46
BUG=chrome-os-partner:60038
BRANCH=master
TEST=build and boot on electro dut
Change-Id: If35e4cf2dbf7c506534c52a052598f6204d5315a
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18183
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The devicetree settings were incorrect in a few places with
respect to the SOC and board design:
- IMVP8 VR workaround is for MP2939 and not MP2949 on Eve
- IccMax values are incorrect according to KBL-Y EDS
- USB2[6] is incorrectly labeled
- I2C touch devices do not need probed as they are not optional
- PCIe Root Port 5 should be enabled
- I2C5 device should not be enabled as it is unused
BUG=chrome-os-partner:58666
TEST=manually tested on Eve board
Change-Id: I74e092444ead4b40c6d8091b80a691d44e2c6c7d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18200
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to get quick boot speeds into recovery enable the
feature that allows for a separate recovery MRC cache.
This requires shuffling the FMAP around a bit in order to
provide another region for the recovery MRC cache. To make
that shuffling easier, group the RW components into another
sub-region so it can use relative addresses.
BUG=chrome-os-partner:58666
TEST=manual testing on eve: check that recovery uses the MRC
cache, and that normal mode does too. Check that if cache is
retrained in recovery mode it is also retrained in normal mode.
Also check that events show up in the log when retrain happens.
Change-Id: I6a9507eb0b919b3af2752e2499904cc62509c06a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18199
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the keyboard backlight as early in boot as possible to
provide a indication that the BIOS is executing.
Since this is bootblock it can't use the convenience function
for checking for S3 resume so just read the PM1 value from the
SOC and check it directly.
Use a value of 75% for the current system as that is visible
without being full brightness.
BUG=chrome-os-partner:61464
TEST=boot on eve and check that keyboard backlight is enabled
as soon as the SOC starts booting
Change-Id: I9ac78e9c3913a2776943088f35142afe3ffef056
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18197
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The PP1800_S rail is turned off in S3. However, enabling internal
pullups on the pins which are connected to PP1800_S results in
leakage into the P1800_S rail. Fix this by disabling the internal
pullups on PP1800_S rail pins.
BUG=chrome-os-partner:61968
BRANCH=reef
TEST=measured leakage on PP1800_S rail. Gone with this patch.
Change-Id: I5ae92b31c1a633f59d425f4105b8db1c9c18c808
Signed-off-by: Aaron Duribn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add weida touchscreen as 2nd touchscreen source
BUG=chrome-os-partner:61865
BRANCH=reef
TEST=emerge-snappy coreboot, and verified that touchscreen works on
snappy.
Change-Id: If76312a62e97da9d5de18ad895e90ee6b0f0c6ae
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18166
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
ELAN touchscreen device expects firmware to export GPIOs and ACPI
regulators for managing power to the device. Thus, provide the
required ACPI elements for OS driver to properly manage this device.
BUG=None
BRANCH=None
TEST=Verified that touchscreen works properly on boot-up and after
suspend/resume.
Change-Id: I78e0c35f60289afe338d140d90784a433ca534ae
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18163
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Remove the 0mA entry for the charger performance table
- Slightly raise the passive limit for TSR2/TSR3 to 55C
BUG=chrome-os-partner:58666
TEST=manual testing on P1 system
Change-Id: I75c66afe04afbbdb64a45833eb938e57ff21b392
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18172
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the ACPI interface to EC driven keyboard backlight.
BUG=chrome-os-partner:61464
TEST=manual testing on P1 system
Change-Id: I13d96c13d7db726b1e8289131db65104bd302efe
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18171
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable an internal pull-up on ACPRESENT signal.
BUG=chrome-os-partner:58666
TEST=manual testing on P1
Change-Id: I0bb86f4547272e021ffd10998faa0e2f103b0808
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18170
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The following devices i2c6, i2c7, spi1, spi2, uart3 are not used.
BUG=none
BRANCH=master
TEST=emerge-snappy coreboot chromeos-bootimage
Change-Id: I9bacdbdd194ce21686c1618494d113402f2bef6c
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18140
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Audio DMIC PLL needs to be ON in S0ix to support
Wake on Voice. This requires GPIO_79 and GPIO_80
to be configured as IGNORE IOSSTATE. So DMIC CLKs
will be ON in S0ix.
Change-Id: If91045a8664ce853366b670b9db38d620818fbab
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/18155
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit 01ba8cf7 (mainboard/google/snappy: Add PowerResource
for ELAN touchscreen)
Change was out of date and broke the build.
Change-Id: Id47631ece1172c3f93bf6f40b8686dfd728842a9
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18158
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
SPI controller need to access flash descriptors/SFDP during s0ix exit,
so all fast SPI IO can't be put into IOSTANDBY state. For reef, that
will be FST_SPI_CLK_FB, GPIO_97, GPIO_99, GPIO_100, GPIO_103 and
GPIO_106.
BUG=chrome-os-partner:61370
BRANCH=reef
TEST=Enter s0ix state in OS, after resume run flashrom to read SPI
content.
Change-Id: I5c59601ec00e93c03dd72a99a739add0950c6a51
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/18137
Tested-by: build bot (Jenkins)
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Define reset_gpio and enable_gpio for touchscreen device so that
when kernel puts this device into D3, we put the device into reset.
PowerResource _ON and _OFF routines are used to put the device
into D0 and D3 states.
BUG=chrome-os-partner:59034
BRANCH=master
TEST=emerge-snappy coreboot chromeos-bootimage
Change-Id: I08c05d06b2812a33b3fdff9b42b2a8e0653dd8b4
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/17366
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Combine existing boards google/enguarde and google/ninja using
their common reference board google/rambi as a baseboard.
Variants contain board specific data:
- DPTF ACPI components
- I2C ACPI devices
- RAM config / SPD data
- devicetree config
- GPIOs
- board-specific HW components (e.g., LAN)
Additionally, some minor cleanup/changes were made:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
The existing enguarde and ninja boards are removed.
Variant setup modeled after google/auron
Change-Id: Iae7855af9a224fd4cb948b854494e39b545ad449
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18129
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Minor cleanup for enguarde and ninja devices:
- enguarde: correct trackpad I2C slave address
- enguarde: remove unused trackpad ACPI devices
- ninja: remove unused PS2 keyboard ACPI device
Change-Id: I1beb34059ba318e2d496a59e4b482f3462faf232
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18128
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
1. Disable WP
2. Pass SD card detect info in ACPI
BUG=chrome-os-partner:60713
BRANCH=None
TEST=Verified that OS is able to detect SD card and read/write to it.
Change-Id: Ide84d4b86c0fac50a07520dfd76d6d3a921f2ecc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18138
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
poppy schematics have undergone change after review, update
DQS and DQ Byte mappings based on the new schematics.
BUG=chrome-os-partner:61856
BRANCH=None
TEST= Build and boot all the poppy proto SKUs to OS.
Change-Id: Ie4532035f37c25540abb26122234f6e3346ede69
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18133
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=chrome-os-partner:60513
BRANCH=None
TEST=Verified that EC SW sync is disabled
Change-Id: I399b26aa64084f5d5e91a2e585281dc48fa81c89
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18114
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=chrome-os-partner:60513
BRANCH=None
TEST=Verified that touchscreen works on poppy.
Change-Id: I0fd605048b91b126ca5b5f8c1c4d6d3f46f866a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18113
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Martin Roth <martinroth@google.com>
|
|
BUG=chrome-os-partner:60513
BRANCH=None
TEST=Picks up correct SPD for index.
Change-Id: Iac683ab3b8151747940b0ad7e257da3d9b0ac622
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18112
Tested-by: build bot (Jenkins)
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=chrome-os-partner:60713
BRANCH=None
TEST=sdcard is detected.
Change-Id: I9ec0cabff0ed7973f5e7dd2c1eae346ae6a1aa99
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18111
Tested-by: build bot (Jenkins)
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The commit 0ba3b2593b0c ("gru: Tuning USB 2.0 PHY to increase
compatibility") bypass ODT to set the max driver strength for
the Type-C otg-port, it works well on otg-port when connected
with USB2.0 devices.
Unfortunately, because the Type-C otg-port and host-port are
consisted in one USB2 PHY, so bypass ODT will have an effect
on both host-port and otg-port. I have tested the host-port
eye-diagram, the result shows that if we bypass ODT, the host-
port eye-diagram height will become to high, more than 500mv,
this may cause USB 2.0 high-speed enumeration failure.
This patch bypass ODT for host-port separately, and then we
can reduce the host-port driver strength without affecting
the otg-port driver strength.
BRANCH=gru
BUG=chrome-os-partner:60727
TEST=Boot system, run 'lsusb' command and check if the usb camera
and usb bluetooth are on usb 2.0 hub or usb 1.1 hub. If they are
on usb 1.1 hub, the issue happens. If not, try to run camera app
and then close camera app, repeat until find that the usb camera
is on the usb 1.1 hub.
Change-Id: Ib693e2a6f2113c06692a7bfee22d85b67ee3b165
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5ea7660b7b05080b76fc5ca5af3fa18552a03491
Original-Change-Id: Ia1f12182929673c5726df9f77f0903469b5c957a
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/425739
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/18126
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Current fw does not create ACPI device for
OS to recognize ELAN touchscreen.
List the touch screen in the devicetree so that
the correct ACPI device are created.
BUG=chrome-os-partner:61803
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I9015fa63ef3aba74b682da3608a05ee49c4947c5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18086
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Restores KB backlight functionality for auron variants
gandof, lulu, and samus.
TEST: boot Lulu and observe KB backlight functional
Change-Id: Iaa852f9327ff1690111db610b4cc5266cd7925b4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17960
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reverts commit 34a6537512d412363bf56428b7ae284e6dd80fb3, which
appears to cause random stability issues on some elm units.
BRANCH=oak
BUG=chrome-os-partner:60869
BUG=chromium:673349
TEST=None
Change-Id: I5ce9e2673db1bc7a1f487a3c3bcce4651a5e3567
Reviewed-on: https://chromium-review.googlesource.com/419862
Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18005
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
1. Update DPTF TSR1/TSR2 passive/critial trigger points.
TSR1 passive point:53, critial point:80
TSR2 passive point:90, critial point:100
2. Update PL1 Min to 4W and PL1 Max to 12W
3. Update thermal relationship table (TRT) setting.
BUG=none
BRANCH=master
TEST=build, boot on snappy dut and verified by thermal team member.
Change-Id: I8b4fb178daa7c2e4091a14779a125bd5e943d023
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/17955
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update the DPTF parameters based on thermal test result.
(ZHT_DPTF_EVT1_v0.3_20161227.xlsx)
1. Update DPTF CPU/TSR1/TSR2 passive/critial trigger points.
CPU critical point:103
TSR1 passive point:45
TSR2 passive point:55, critical point:90
2. Change thermal relationship table (TRT) setting.
Change CPU Throttle Effect on CPU sample rate to 3secs
Change Charger Effect on Temp Sensor 2 sample rate to 60secs
Change CPU Effect on Temp Sensor 1 sample rate to 8secs
BUG=chrome-os-partner:60038
BRANCH=master
TEST=build and boot on electro dut
Change-Id: I3746750f7ea4a2e01153a36c28a5c33140c9e38c
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/17975
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable an internal pull-up on the power button input as a quick
press is resulting in power button override being asserted.
BUG=chrome-os-partner:61312
TEST=tested on eve P0b to ensure quick power button press does
not result in a shutdown due to power button override.
Change-Id: I3028cf7faef309cf4d60c3585b48adab6e1549d4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17962
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
With the default TCC activation offset value as 0 and Tjmax
temperature value as 100 degree C, Pcode firmware starts taking
prochot action at 100 degree C [Tjmax-Offset].
But before Pcode firmware starts prochot action at 100 degree C,
device is getting shutdown at 99 degree C due to DPTF critical
CPU temperature.
This patch sets TCC activation offset value to 10 degree C for
thermal throttle action to prevent this kind of shutdown.
BUG=chrome-os-partner:59397
BRANCH=None.
TEST=Built, booted on skylake and verified target offset value.
Change-Id: I0811ef481a4b3ce4bd6ef24f2aa8160f44f9c990
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17921
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with
the ability to perform tx and rx of flash command and response at the
same time. Instead of introducing this notion at SPI flash driver layer,
clean up the interface to SPI used by flash.
Flash uses a command-response kind of communication. Thus, even though
SPI is duplex, flash command needs to be sent out on SPI bus and then
flash response should be received on the bus. Some specialized x86
flash controllers are capable of handling command and response in a
single transaction.
In order to support all the varied cases:
1. Add spi_xfer_vector that takes as input a vector of SPI operations
and calls back into SPI controller driver to process these operations.
2. In order to accomodate flash command-response model, use two vectors
while calling into spi_xfer_vector -- one with dout set to
non-NULL(command) and other with din set to non-NULL(response).
3. For specialized SPI flash controllers combine two successive vectors
if the transactions look like a command-response pair.
4. Provide helper functions for common cases like supporting only 2
vectors at a time, supporting n vectors at a time, default vector
operation to cycle through all SPI op vectors one by one.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17681
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Combine existing boards google/auron_paine and google/samus with new
ChromeOS devices auron_yuna, gandof and lulu, using their common
reference board (auron) as a base.
Chromium sources used:
firmware-yuna-6301.59.B 6ed8b9d [CHERRY-PICK: broadwell: Update to...]
firmware-gandof-6301.155.B 666f34f [gandof: modify power limiting for...]
firmware-lulu-6301.136.B 8811714 [lulu: update RAMID table]
Additionally, some minor cleanup/changes were made:
- I2C devices set to use level (vs edge) interrupt triggering
- HDA verb entries use simplified macro entry format
- correct FADT table header version
- remove unused ACPI device entries / .asl file(s)
- clean up ACPI code (e.g., trackpad on Lulu)
- adjust _CID for trackpad on Lulu in order to not load non-functional
Windows driver (does not affect Linux)
- remove unused header includes (multiple/various)
- correct I2C addresses used for SMBIOS device entries
- correct misc typos etc
The existing auron_paine samus boards are removed.
Variant setup modeled after google/slippy
Change-Id: I53436878d141715eb18b8ea5043d71e6e8728fe8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17917
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Combine existing boards google/guado, rikku, and tidus using
their common reference board google/jecht as a base.
Additional changes besides simple consolidation include:
- simplify power LED functions
- simplify HDA verb definitions using azelia macros
- use common SoC functions to generate FADT table
- correct FADT table header version
- remove unused haswell_pci_irqs.asl
- remove unused header includes (various)
- set sane default fan speed (0x4d) for all variants
Variant setup modeled after google/beltino
Change-Id: I77a2dffe9601734916a33fd04ead98016ad0bc4b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17913
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Both HDMI and eDP work (simultaneously).
TESTED on Acer C720 (peppy).
Change-Id: Ifc4e3c187bcabd8965d9586237a52b440bfa7f20
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17916
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
GPP_D12 needs an internal pull-up to get this rail working on
current boards. GPP_D0-GPP_D3 were changed from SPI interface
and I just missed this change earlier.
BUG=chrome-os-partner:58666
TEST=test camera and touchpad on eve
Change-Id: Idfa186f2930afbe5651f4e0fc11a19cd0dd4295f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17922
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add poppy board files using kabylake and FSP 2.0.
BUG=chrome-os-partner:60713
BRANCH=None
TEST=Compiles successfully
Change-Id: Ic9aa5093b319690ae893a21cab98d9b843000e6c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17866
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
ELAN touchscreen device expects firmware to export GPIOs and ACPI
regulators for managing power to the device. Thus, provide the
required ACPI elements for OS driver to properly manage this device.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that touchscreen works properly on boot-up and after
suspend/resume.
Change-Id: I298ca5de9c0ae302309d87e3dffb65f9be1e882e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17799
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Set the thermal throttle (prochot) activation to be 10 degrees
below TJmax so PROCHOT# kicks in at 90C instead of 100C.
BUG=chrome-os-partner:58666
TEST=boot on eve, check msr value before and after resume:
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
> echo mem > /sys/power/state
> iotools rdmsr 1 0x1a2
0x000000000a6400e6
Change-Id: I3ab3a050a1e27c18a940bd7519eabaf015ef93eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17901
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add power management type config option that allows mainboards to
either:
1. Define a power resource that uses the reset and enable gpios to
power on and off the device using _ON and _OFF methods, or
2. Export reset and enable GPIOs in _CRS and _DSD so that the OS can
directly toggle the GPIOs as required.
GPIO type needs to be updated in drivers_i2c_generic_config to use
acpi_gpio type so that it can be used for both the above cases.
BUG=chrome-os-partner:60194
BRANCH=None
TEST=Verified that elan touchscreen works fine on reef using exported
GPIOs.
Change-Id: I4d76f193f615cfc4520869dedc55505c109042f6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17797
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable the actual touch devices to be probed by the kernel
and remove the placeholder devices that I put in before
and were used for initial bringup.
BUG=chrome-os-partner:58666
TEST=tested on eve
Change-Id: I7fc6f9da83b1abbae6dd069f759b220d59153d1c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17896
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Put the UART pins into native mode in bootblock so they are not
floating when we try to communicate with H1 over I2C. Without
a serial console enabled BIOS these pins were not configured
until ramstage.
BUG=chrome-os-partner:60935
TEST=Boot Eve board without serial console and H1 TPM enabled
Change-Id: I30f3bf0bacc1bbd776b351a9c09748b0601c39bc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17893
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
For Chrome OS the normal MRC cache should be cleared when a hardware
retrain recovery request is observed. The reason is that since there
are 2 different MRC cache slots there needs to be a mechanism which
allows an end user make a system bootable again if the MRC settings
happen to not allow the system to boot any longer. Therefore, one
just needs to enter recovery with the hardware retrain flag and
the system normal MRC cache slot will be invalidated.
BUG=chrome-os-partner:60592
BRANCH=reef
Change-Id: I6ad32ed0dd217d66404b77467a88689a06044544
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17871
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
VARIANT_DIR is defined in coreboot/Makefile.inc, so doesn't need to be
defined in each mainboard.
Change-Id: Ic93957b710e4a9863774de7fcf3bd006696b6aa1
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17841
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On this board i2c3 bus is connected to the display TCON, but it is
acting as the master when it has power so it can read from its own
EEPROM on the bus. In order to prevent any possible issues in S0
make these pins input on the SOC.
BUG=chrome-os-partner:58666
TEST=tested on eve board, but this bus was not used before so
there is no visible change in behavior.
Change-Id: Ide32f45ee33ca986fd3249a5161e01edf99d6e22
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17800
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
On upcoming boards an optional pull up is applied on GPIO_10
to indicate if the board should have security features locked
down for a shipping system. Provide a weak pull down so that
all boards will indicate a logic 0 until the stronger pull up
resistor is stuffed.
BUG=chrome-os-partner:59951
BRANCH=reef
Change-Id: I6f514a69bccd05ca02480f3c30d0ad503a955b1e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17803
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Chrome OS images have three firmware ID regions, to store version
information for the read-only and the two read-write areas. Fill them
with a suitable default and allow configuring a different scheme.
There's already an override in google/foster and google/rotor to match
the naming scheme used so far (in depthcharge).
BUG=chromium:595715
BRANCH=none
TEST=/build/$board/firmware/coreboot.rom has the expected values in the
regions.
Change-Id: I5fade5971135fa0347d6e13ec72909db83818959
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d2e3be81faa8d21f92325294530714a4b18a1b3e
Original-Change-Id: I2fa2d51eacd832db6864fb67b6481b4d27889f52
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/417320
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: https://review.coreboot.org/17788
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch sets PL2 override value to 15W in RAPL registers
and sets DPTF PL2 Max to 15W
BUG=none
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: Ibadf0fa442f556d018c249b1cf88e29c4d57c97f
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/17779
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fill in the NHLT ACPI OEM header fields to differentiate
different audio solutions on a per board basis. This handles
boards that share a firmware that are differentiated by
the SKU id and boards that have their own firmware. For the
latter, the Oem Table ID uses the VARIANT_DIR to differentiate.
"reef" is always used for Oem ID which is treated as more of
family in this case.
iasl -d shows the following on reef:
[00Ah 0010 6] Oem ID : "reef"
[010h 0016 8] Oem Table ID : "reef"
[018h 0024 4] Oem Revision : 00000008
BUG=chrome-os-partner:60494
BRANCH=reef
Change-Id: I5daa6f0306bc05e812a8737ce61ee37177a36b76
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17772
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There are 2 gpios on reef-like boards that can be composed
into a SKU. Add support for identifying the SKU value using
the base 3 gpio logic. Also export the SKU information to the
SMBIOS type 1 table.
BUG=chrome-os-partner:59887,chrome-os-partner:60494
BRANCH=reef
Change-Id: I8bb94207b0b7833d758054a817b655e248f1b239
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17771
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There is ongoing work to link SPI bus and devices in to the devicetree
so this can be generated, but for now put in the raw ASL code to
describe this controller so it can be used by the factory.
BUG=chrome-os-partner:55538
TEST=successfully load fpc1020 kernel module on eve board
Change-Id: I6641664e60fcf2c0bad4b3506c77513b26d7be2e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17776
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:60535
TEST=Built, booted on reef and verified PL2 value.
Change-Id: I4ff6a5e7b8686d97134846ee80cdac10916d58ef
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17730
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Simplify set_power_led() by consolidating switch and setting values
as needed inline based on LED state. Remove unnecesary function
param, includes for Tidus.
Change-Id: I28e6fac5f8d7e2ff419002db714ce88697895faf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17744
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Simplify set_power_led() by consolidating switch and setting values
as needed inline based on LED state.
Fix non-off LED polarity for Tricky using correct value from Chromium source
TEST: power on Tricky, observe LED lit / solid
Change-Id: I8bc7c4ae3f83d3f37b76fd5c90a4faed7057ebee
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17719
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Doing PCI config operations via MMIO window by default is a
requirement, if supported by the platform. This means chipset
or CPU code must enable MMCONF operations early in bootblock
already, or before platform-specific romstage entry.
Platforms are allowed to have NO_MMCONF_SUPPORT only in the
case it is actually not implemented in the silicon.
Change-Id: Id4d9029dec2fe195f09373320de800fcdf88c15d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17693
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- Drastically reduced RW_MRC_CACHE size to hold one update. Now
that this area isn't changing after every S5 entry there's no
need make it so large.
- ELOG area reduced by 4KiB for subsequent area alignment. In practice
this doesn't matter because the elog library only uses 4KiB bytes.
16KiB->12KiB is a nop.
- Moved RW_NVRAM for subsequent alignment.
- Most importantly, RW_SECTION_(A|B) are aligned to 64KiB boundaries
and sized to 64KiB multiples. This ensures updates don't need a
read-modify-write that could force a system into recovery if
an inopportune power event occurred.
BUG=chrome-os-partner:60492
BRANCH=reef
Change-Id: I2a2e2797897c934db1a3f9627c6c13a9b2aad540
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17727
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Update the memory ramid.
Move to one CA training pattern.
BUG=chrome-os-partner:59454
BRANCH=firmware-gru-8785.B
TEST=Build firmware passed
Change-Id: Ic05cbc1700a13e372f63d5202459add0e984f9d8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1030a78af3d489d13508f17a79df1e65bd5afa3b
Original-Change-Id: Ibe8acb5b698cec1adcdddbb13d35a5e20a5b8c0d
Original-Reviewed-on: https://chromium-review.googlesource.com/414664
Original-Commit-Ready: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Change-Id: I0ae46e496cd18492a2b6c7167081798c2f2479b1
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411645
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17679
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add bob in coreboot and update as necessary.
1. Add bob HWID
2. Add supported memory source
BUG=chrome-os-partner:59454
BRANCH=firmware-gru-8785.B
TEST=Build firmware passed
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Change-Id: Iad03a293bdbbb89450f0fea0822e34a4be7064bf
Original-Commit-Id: bff788c71a43403bff2c23b38e69cc27fb869559
Original-Change-Id: I0dcf47eb911337b176f73759a2c70a9dbf4dc68b
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411083
Original-Reviewed-by: Philip Chen <philipchen@chromium.org>
Original-(cherry picked from commit c5925dfcf59ac755a26182744b2bde59e41a37cf)
Original-Reviewed-on: https://chromium-review.googlesource.com/413744
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17678
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We may support different sdram sizes on one board in future, so
we need to calculate sdram sizes from sdram drvier.
BRANCH=None
BUG=None
TEST=boot kevin
Change-Id: I43e8f164ecdb768c051464b4dbc7d890df8055d0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3c4d8b3cb647b2f9cebc416c298817c16d49330e
Original-Change-Id: I95d5ef34de9d79ebca3600dc7a4b9e14449606ff
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411600
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17629
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gru only uses USB 2.0 in firmware to avoid all the madness associated
with Type-C port orientation and USB 3.0 tuning. We do this by isolating
the SuperSpeed lines in the Type-C PHY so it looks like they aren't
connected to the device.
Unfortunately, some devices seem to already get "locked" into SuperSpeed
mode as soon as they detect Rx terminations once, and can never snap out
again on their own. Since the terminations are already connected during
power-on reset we cannot disable them fast enough to prevent this, and
the only solution we found to date is to power-cycle the whole USB port.
Now, Gru's USB port power is controlled by the EC, and unfortunately we
have no direct host command to control it. We do however have a command
to force a certain USB PD "role", and forcing our host into "sink" mode
makes it stop sourcing power to the port. So for lack of a saner
solution we'll use this to work around our problem.
BRANCH=gru
BUG=chrome-os-partner:59346
TEST=Booted Kevin in recovery mode, confirmed that my "problem stick"
gets detected immediately (whereas previously I had to unplug/replug
it). Booted Kevin to OS in both developer and normal mode and confirmed
that USB still seems to work.
Change-Id: Ib3cceba9baa170b13f01bd5c01bd413be5b441ba
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cd695eda33299e50362f1096c46f2f5260c49036
Original-Change-Id: I2db3d6d3710d18a8b8030e94eb1ac2e931f22638
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/413031
Reviewed-on: https://review.coreboot.org/17628
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic22beaa47476d8c600e4081fc5ad7bc171e0f903
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17735
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
