Age | Commit message (Collapse) | Author |
|
Configuring EC_PCH_WAKE_L as an SCI enabled GPIO allows the EC to wake
the AP from S3 on keyboard presses.
BUG=b:109759838
TEST=(1) powerd_dbus_suspend
(2) press a key on the internal keyboard
=> system resumes from S3
Change-Id: I30f72460fd588706f91f4fc3ea4ff007c96e9ebe
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26931
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change b41ae2 (mb/google/octopus: Enable wake-over-wifi for octopus
variants) changed the GPE mappings to accomodate for WiFi wake
pin. However, this resulted in TPM interrupt pin being removed from
the GPIO to GPE mapping. Since we do not support true interrupts in
coreboot, GPE_STS registers are used to identify if an interrupt has
triggered. Change in GPE mapping resulted in this information to be
lost when talking to TPM thus resulting in "Timeout wait for tpm
irq".
This change fixes the above issue by assigning GPIO block for TPM
interrupt back to DW1 and moving GPIO block for wake-over-wifi pin to
DW3. DW3 was mapped to NW_31_0 which only has debug header pins and
CNVI pins (none of them are used for reading GPE_STS or as wake
sources).
BUG=b:109824918
TEST=Verified that there are no "Timeout wait for tpm irq" messages
when talking to TPM.
Change-Id: I30768177a838a684948f7485d760c8b83c3190f7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
|
|
TPM over SPI/I2C config selection got changed in
https://review.coreboot.org/c/coreboot/+/24903 so this CL is fixing the
same.
BUG=None
BRANCH=None
TEST=Build for Soraka & make sure that TPM is probed over I2C interface
rather than SPI.
Change-Id: I077e4dc03520e26eb9f6404a7eb1edd99925de77
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26890
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Sona.
We need to disable rear camera/DMIC on all Sona sku.
BUG=b:109710674
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Sona
Change-Id: Id84ee22c9ffc15db78be3bbad148af5cd7dc866e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since there are two cameras on Nami and only one camera on Pantheon.
We need to disable rear camera/DMIC on all Pantheon sku.
BUG=b:109720689
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Pantheon
Change-Id: Ibe48a945dc57f2c05344479253040ad1945d92fd
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I3e0ca62ad88aea5c99f9f0902ad8553656469a1c
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/26936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Update GPIOs in baseboard to match latest schematics:
1. Get rid of STEST GPIOs(GPIO_{62,84-89})
2. Get rid of SD_CD_ODL(GPIO_134)
3. Get rid of KB control GPIOs(GPIO_{144-146})
4. Configure GPIOs for pen eject (GPIO_{144,145}). Additionally, fix the
configuration for other pen GPIOs.
BUG=b:109764138
Change-Id: I8e40dd90b2784596f055538e57ea67482c4c517a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26874
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the normal termination is None, the standby termination is
none also as per Doc# 572688. So when termination is only needed in
standby, use the IOSSTATE setting that drives low/high via the
Tx mode instead.
Also disabled Speaker in Standby state to save power.
BUG=b:79874891, b:79982669
BRANCH=None
TEST=Compiled and flashed image on Bip. Checked that suspend_resume cycles
pass. Checked that bluetooth is functional on resume. On Yorp, checked
that speaker is functional after a suspend/resume cycle.
Change-Id: I6a3852548f944176a80feb32e9885b03b8af25db
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/26762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Issue observed on the board is: too many jack interrupts.
cat /proc/interrupts | grep da7219
58: 84292 15709 0 0 IO-APIC 58-fasteoi da7219-aad
Updated pad configuration for Jack IRQ pin to fix the issue.
BUG=b:109655907
TEST=Jack insertion & removal detection is working.
Change-Id: I41ef9d40325677b01ca94ec3215e7feded76dcc3
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
During measurement of signals during Elan touchscreen power on, saw
that the enable_gpio delay was not sufficient as there is a +1.5 ms
delay during power on. Adding more delay to take this into account.
BUG=b:78311818
BRANCH=None
TEST=probe power on signals to ensure meet timing requirements
Change-Id: Id661a202188a97aef97514ebecd0be6fc022d21e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Power off does not seem to use the ACPI _OFF function, but rather the
smihandler. Creating variant_smi_sleep function for nami to handle
the power off sequence during reboot/power off.
BUG=b:78311818
BRANCH=None
TEST=Run "poweroff" command from AP console with SMI_DEBUG enabled
Make sure delays are consistent with spec
Change-Id: Ifeea545fe268be249793b3e508c51f5e4c1a3460
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables wake-over-wifi functionality for all octopus
variants by making the following changeS:
1. Configure GPIO_119 as SCI active-low
2. Update GPE0_DW1 to include the group that GPIO_119 falls under
3. Add wake property to wifi device
BUG=b:77224247
TEST=Verified that wake-over-wifi works on yorp.
Change-Id: Ibae199c43e4d96da4c2f68f71a849c2f23d3e7b9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since Vayne added one more skuid 3A67, we need to disable rear
camera/DMIC for vayne skuid 3A67.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Vayne
Change-Id: I9131b4c41bf189829be4e7e6bfaf4a96765cfa15
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26855
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization for CNL.
Change-Id: Ia7da0842996a9db09e6e2b7b201b3a883c3887a2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Remove 2nd software stack in pc80 drivers directory.
* Create TSPI interface for common usage.
* Refactor TSS / TIS code base.
* Add vendor tss (Cr50) directory.
* Change kconfig options for TPM to TPM1.
* Add user / board configuration with:
* MAINBOARD_HAS_*_TPM # * BUS driver
* MAINBOARD_HAS_TPM1 or MAINBOARD_HAS_TPM2
* Add kconfig TPM user selection (e.g. pluggable TPMs)
* Fix existing headers and function calls.
* Fix vboot for interface usage and antirollback mode.
Change-Id: I7ec277e82a3c20c62a0548a1a2b013e6ce8f5b3f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I24fd33887152c12b9db9742af475115b02b31ff2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Because of struct sci_source table of events that have to generate SCI or
SMI, <soc/smi.h> was included to kahlee/grunt gpio.c files. However, new
code transfered most of SCI/SMI/interrupt programming (with exception of
events not associated to a GPIO pin), and therefore smi.h is now included
by gpio.h. It was also added to some other files where they are not needed.
Only smihandler.c truly needs it. Remove the includes.
BUG=b:78139413
TEST=build and boot grunt.
Change-Id: I64cf0796103a5226ddace03d05d94160bf93aa69
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26721
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load vbt-vayne.bin by reading sku-id.
BUG=b:80509366
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: Ia26ea4a9b7679aeb9d98f19ffaa1b686af828339
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently the throttle event handler method THRM is defined as an
extern on the intel bd82x6x and lynxpoint chipsets, then defined
again in the platform with thermal event handling. In newer versions
of IASL, this generates an error, as the method is defined in two
places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
This also requires moving the thermal handler, which now includes
the define to before the gnvs asl file.
TEST=Build before and after, make sure correct code is included.
Change-Id: I7af4a346496c1352ec20bda8acb338b5d277d99b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26123
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The driver only supports streaming images flipped horizontally
and vertically. In order to ensure that all current users will
be fine if or when support for upright streaming is added,
require the presence of the "rotation" control now.
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: I7e3abdea9071da1a089c7165f6bb609428090792
Signed-off-by: Lai, Jim <jim.lai@intel.com>
Reviewed-on: https://review.coreboot.org/26727
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Patch adds required changes for RT5682 codec enablement for the BIP board.
And code clean-up nhlt blob selection method in config.
BUG=b:77892150
TEST=build and boot on a BIP PO board.
verify headset codec i2cdetects at address 1a.
Change-Id: Iee91518c03a0e9e6ed52bc54a60fc607730a0b7d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/26211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change updates rambi ec init to perform SMI mask setting using
google_chromeec_events_init.
Change-Id: I7def3c07b4d7bfbe15b2d1c45381bdc31b7e3476
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This adds all USB ports to the device tree. Additionally, it adds _PS0
and _PS3 ACPI methods for the visible USB A ports, which makes it
possible to control the port power (VBUS) of each port individually.
Change-Id: I80ba090f323fbf9fc2b333b1c647b7dfb3393ff6
Signed-off-by: Emil Lundmark <lndmrk@chromium.org>
Reviewed-on: https://review.coreboot.org/26472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add Careena variant, based on the grunt board.
BUG=b:80106042
TEST=Build Careena
Change-Id: I87a24f6d8115aacf5b21181f3820cf2718ad252a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The FPMCU is using the standard cros-ec-spi interface on GSPI1.
Configure the GPIOs controlling the MCU too.
We need to be able to wake from S3 on the MCU interrupt, re-configure
GPE0 DW0 to point to GPP_C bank.
BRANCH=poppy
BUG=b:79666174
TEST=exercise the cros_ec interface, e.g. 'ectool --name=cros_fp version',
verify the MKBP events by doing 'ectool --name=cros_fp fpmode fingerup'
then 'ectool --name=cros_fp waitevent 5 10000', toggle the other GPIOs
with the flash_fp_mcu script.
Change-Id: Ib417dcf84cda8e354060785cd16a7b6b812148d5
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/26684
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The chrmoeos.fmd file will be common across variants, so move it out of
of grunt directory and into the variants/baseboard directory.
BUG=b:80106042
TEST=Build grunt
Change-Id: I259d85f60c5e19e00f7d9149542bcfdcc6dfaf4f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The SPD files will be common to many of the mainboards, so move them out
of grunt and into the variants/baseboard directory.
BUG=b:80106042
TEST=Build grunt, make sure spd.bin is the same.
Change-Id: I53975a46a8c7d7e519bb6f7ef6ccd0b817ac4c92
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently the throttle event handler method THRT is defined as an extern,
then defined again in the platform with thermal event handling. In newer
versions of IASL, this generates an error, as the method is defined in
two places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
Change-Id: I6337c52edaf9350843848b31c5d87bbfca403930
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
Furthermore, some of these pins were configured with normal termination
of None which would as per above mentioned document lead to a standby
termination of None anyways.
Instead of pull downs, use the IOSSTATE setting for driving low
via the Tx mode.
BUG=b:79874891, b:79494332, b:79982669
BRANCH=None
TEST=Flashed image and booted to OS on Yorp. Touchscreen does not
consume power in suspend state.
Change-Id: I7dcf3691b969d018b3cfb6af3f7467c9b523fee5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/26491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This won't actually get called yet since the GPIO pin has not been
configured as SMI.
BUG=b:80295434
TEST=grunt: Made sure events could be processed.
Change-Id: I189e26196e4543b3e34bff5d9df8566eff07d585
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The default interrupt control for GPIO pins within stoneyridge is for
edge triggered, high. However, sometimes these need to change, or maybe
the interrupt needs to be reported or delivered. This was the case of
platform grunt, where the interrupt related bits were being changed
afterwards. Ideally all the bits should be programmed through the same
procedure. Create several PAD_INT definitions (for general configuration,
for trigger configuration and for interrupt type configuration) and change
function sb_program_gpios() to accept the output from PAD_INT_XX and
program all the necessary bits while keeping compatibility with other
PAD_XX definitions.
BUG=b:72875858
TEST=Add code to report GPIO and interrupt configuration, build grunt and
record a baseline. Add new code, rebuild grunt and record a test output.
Compare baseline against test, there should be no change in GPIO or
interrupt programming.
Remove code that reports GPIO/interrupt configuration.
Change-Id: I3457543bdf64ec757fd82df53c83fdc1d03c1f22
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change moves PL2 override to variant_devtree_update for two reasons:
1. This function was added to basically override devtree settings in
variant specific code. So, it would be a good idea to perform all the
overrides in a single place.
2. Adding a device for performing nami_enable would require changes to
devicetree and special handling for calling this device enable. Thus,
nami_enable was never getting called.
BUG=b:80148703
Change-Id: Ifa24a7b6e99cad2368b3d656a757f26297373121
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In cbdbf018 (mb/google/reef/variants/: Add new memory ID) a
new memory configuration entry was added. However, it was using
spaces for indention. Correct that.
Change-Id: Iaf788b0ad8a6ef3b001e7f29a6710e6e8f731ecf
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/26513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The BT W_DISABLE2# pin is connected to GPP_E4 in the latest schematic.
Update GPP_E4 as GPO and set 1 as default.
BUG=b:79993692, b:72007632
BRANCH=None
TEST=Enable/disable BT/WLAN by following command.
Enable:
localhost ~ # iotools mmio_write32 0xfdae0590 0x40000201
localhost ~ # iotools mmio_write32 0xfdae05a0 0x40000201
Disable:
localhost ~ # iotools mmio_write32 0xfdae0590 0x40000200
localhost ~ # iotools mmio_write32 0xfdae05a0 0x40000200
Change-Id: I9ef1a5314652ab29172d246abd58ee4e1a8a6299
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26502
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO APU_BIOS_FLASH_WP_L is first read in ROM stage to determine the
state of the BIOS FLASH Write Protect signal at boot.
The result of this read accumulated in the vboot state that's passed on
to the upper layers of the stack.
Therefore this GPIO must be configured as a "reset stage" GPIO, not
a "RAM" stage GPIO.
BUG=b:79866233
TEST=firmware_WriteProtect
Change-Id: I1d96ab4bbfeaf9db9f74cf0c58cbab2104079bf7
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26498
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ApolloLake based reef platform is fan-less design. We do not need
these DPTF_CPU_ACTIVE_ACx defines. Removing these from all reef
variants as those are not being used.
Change-Id: Id3cb7f7826a5e02cf447c70ab5cdc9b5d86982ca
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/26468
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If450a68e98261ffba4afadbce47c156c7e89e7e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26460
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables SAR config on Nami with CHROMEOS option.
BUG=b:75077304
BRANCH=master
Change-Id: I8217333db2db6c0fd5e1c144dedd3692b1e1e6a3
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
_SWS is the recommended method of wake source retrieval. Now that PM1I and
GPEI are available at NVS, add the method _SWS to kahlee/grunt ACPI code.
BUG=b:76020953
TEST=Build grunt
Change-Id: I5930438af40e6f9177462582cafb65401d9c60f4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:79617938
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage", flash nocturne,
boot to kernel, run evtest and verify that cros-ec-buttons is present
and functional.
Change-Id: Id710782e1f4e18eaac2a90c7c0f91af5223dbce3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable I2C #5 for rear camera and SAR.
BUG=b:79784124
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' and verify i2c bus #5
is detected.
Change-Id: Ic5b754fb97231aeab0278d71f8ced9343c30feda
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Drive SPKR_RST_L (GPP_A19) high at boot to take audio amps out of
reset.
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage", boot to kernel,
and verify sound works via "aplay /dev/random"
Change-Id: Ia49931f2dc7802edc8a46114b081e4a96eeee604
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- add ACPI register information for touchscreen WCOM digitizer
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify
touchscreen on Nocturne board works.
Change-Id: I9790a930e8ed2748d568ce58c931ce34b3e22007
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the size in WP_RO segment of the flash to accommodate latest FSP builds
with debug.
CQ-DEPEND=CL:*627827
Change-Id: Ic0eb9254421e99c8d204d8dbb86e6c6c2ec8719c
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/26186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the unused space to the RW_LEGACY area.
BUG=b:79433466
TEST=None
Change-Id: I897d1dcf75466fe9bdb814c8a9db0fecb5c42af6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The firmware_Mosys FAFT test does not allow RW_SECTION_A, RW_SECTION_B or
RW_SHARED to be 0-sized, nor located at offset 0x00000000.
Swap UNIFIED_MRC_CACHE and RW_SECTION_A to pass this test.
BUG=b:79865447
TEST=test_that -b grunt ${IP} firmware_Mosys
Change-Id: If60919fd998ac786d58a5a258d7b5ded727db64b
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables the new bootblock compression feature on RK3399,
which requires moving MMU initialization into the decompressor stage and
linking the decompressor (rather than the bootblock) into the entry
point jumped to by the masked ROM.
RK3399's masked ROM seems to be using a bitbang SPI driver to load us
(very long pauses between clocking in each byte), with an effective data
rate of about 1Mbit. Bootblock loading time (as measured on a SPI
analyzer) is reduced by almost 100ms (about a third), while the
decompression time is trivial (under 1ms).
Change-Id: I48967ca5bb51cc4481d69dbacb4ca3c6b96cccea
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/26341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Lower the amount of UMA memory to 32MB at AMD's request.
TEST=none
BUG=b:79906569
Change-Id: Ib1365dc38850b4b92c944ff95534573addbe4362
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Lower the amount of UMA memory to 32MB at AMD's request.
TEST=boot Grunt, try S3
BUG=b:79906569
Change-Id: I5af038688b38b53c94b8265823eeee0f37980522
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Bip should have different devicetree entries than Yorp; it doesn't have
a DA7219 audio codec (instead it uses ALC5682).
BRANCH=none
BUG=b:79771967
TEST=boot, no longer see DA7219 ACPI in console.
Change-Id: Ic63bbc51e122afc9fc2e8ec7fb024d18a3815b38
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/26342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
BUG=b:79343083
BRANCH=NONE
TEST=On Yorp board, lspci should list xdci,
00:15.1 USB controller
Change-Id: I3a4878389a1b5b7abcaccf6ab16b67848aaaee83
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/26358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add a new RAM ID of memrory PN:K4F6E3S4HM-MGCJ
BUG=b:78491470
TEST= emerge-coral coreboot chromeos-bootimage.
Change-Id: Ic40e36ab222572945f8588eb3df063e4fe0dbeb5
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/26365
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Describe the USB devices in the devicetree so they can get
generated into the SSDT and presented to the OS.
This was tested on an eve board and the resulting SSDT was
verified to show the expected values in _UPC and _PLD.
Change-Id: I292426f588ea74d61a5c4e4b01386bb18834c117
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/26176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The I2C CLKs of SoC should be 400kHz, but waveform show 460kHz to
470kHz. Add I2C parameters to adjust I2C CLKs which 5% lower than
400kHz.
BUG=b:78819970
TEST=The I2C CLKs are 5% lower than 400kHz.
Change-Id: I2c3012b5b59c089801cda8fd7b0c433aad9df36d
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26282
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify pogo
pin port is working.
Change-Id: Ide7359366821f33c4746284e65cacdf4e240931d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The CNVi wifi/bt module prevents entry into S5 by keeping internal
SoC clocks running. Therefore it's necessary to disable BT prior to
S5 entry.
BUG=b:79606769
TEST= Test if BT device works under following cases:
1. Power-on
2. Press powerbtn before OS entry
3. Power-on from S5 again
Change-Id: Ibc14b4080a27de48d197e16d0eed162603482de2
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/26238
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptf.asl from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI.
Change-Id: I21ddc337359c3e11ad9756e61ba174b33dfc3c75
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Since there are two ALS device nodes on Nami, need to remove one.
BUG=b:79227879
BRANCH=master
TEST=Verify if only one ALS node is found in /sys/bus/iio/devices
Change-Id: I850af06bec833739afa0c8c516d351d81952ce2c
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26271
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load pantheon.bin by reading sku-id.
BUG=b:78663963
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I66cb43d87363b3e8b1a1498cdae8eeeb8b75219d
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:74595040
BRANCH=master
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. Booted on Pantheon with S7817 PCBa connected
3. Check touchscreen device is enabled by evtest
/dev/input/event4: SYTS7817:00 06CB:7817
Change-Id: Ic11684d5ed961af5eb704909f7d06eb0898068c2
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix dual LAN sku can't inherit correct MAC from VPD setting.
BUG=b:77836343
BRANCH=Fizz
TEST=Program the mac address to VPD in shell
vpd -s ethernet_mac0=<mac address1>
vpd -s ethernet_mac1=<mac address2> && reboot the system.
Ensure the MAC address was fetched correctly by ifconfig command.
Change-Id: Ic357a3f1435d6d08107520e40872f1003ef2edf3
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/25587
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds board-specific implementation of
mainboard_vbt_filename which returns "vbt.bin" by default. This is in
preparation to allow multiple vbt binaries to be added to single
image. More sku_id specific names will be added in follow-up CLs.
BUG=b:79396300
Change-Id: I3821d55bfbe9e5773bd2eb0b0003045a80158d8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Current VBT setting for T8 is only 1ms which is under Innolux
N116BCA-EA1 panel's spec.
Modify T8 to 100ms.
(Innolux's panel's spec requires T8 needs to be greater than 80ms
BUG=b:78541692
BRANCH=master
TEST=emerge-coral depthcharge coreboot chromeos-bootimage
Run on DUT and check panel sequence meets spec.
Change-Id: I5f9103aca7871095a828a74cd6a97e1951adb81f
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/26214
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new RAM ID of memrory PN:MT53E512M32D2NP
BUG=b:78491470
TEST= emerge-coral coreboot chromeos-bootimage.
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Change-Id: I855702c2850887df74941e00da69322124557498
Reviewed-on: https://review.coreboot.org/26213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Ren Kuo <ren.kuo@quantatw.com>
|
|
This adds a new SPD entry for samsung's new 4GB memory and updates
atlas to use it instead of the previous gen memory.
BUG=b:79444337
TEST=booted on atlas
Change-Id: I19567736c45a1321586378c3d964c2cbebe24755
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/26185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This keeps Audio clock and data pins ON in S0ix to support
Wake on Voice.
BUG=b:77605180
BRANCH=none
TEST=Checked that S0ix suspend/resume works. Validation of WoV
was done on glkrvp previously. For Yorp, audio topology firmware
updates are required for testing WoV.
Change-Id: Idafe4e7d24fe16f8e8ff3dd86e299776ea860d03
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/26202
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
hynix/H9CCNNNCLGALAR-NUD
nayna/NT6CL256T32CM-H1
BUG=b:79443146
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I3a362080b9e60adecbac14d5cfe193da44bf87c8
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to ACPI 6.1 spec 19.6.44, External informs compiler that
object is external to this TABLE, no necessary for object in same DSDT
tables.
A name cannot be defined and declared external in the same table (GPID)
A name cannot be defined and declared external in the same table (CTOK)
Change-Id: Ica80b59ad6a8af865bf1551ac4e014ec5f4e7d08
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26122
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the below:
1)
Nocturne board has only Max98373 speaker amp.
Update both NHLT and DT entries to include only Max98373
and not include DA7219.
2) I2S2 is used for Boot Beep.
So, update GPP_F0 ~ F2 pins accordingly.
3) Include DMIC-4ch configuration.
BUG=b:79362472
TEST=None [Waiting for HW to verify]
Change-Id: I0e9b3a564c22de6e84e96e5e937a3aca4ae73d75
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of both featuring their own VBT loaders, use a single one.
It's the compression-enabled one from soc/intel/common, but moved to
drivers/intel/gma.
The rationale (besides making all the Kconfig fluff easier) is that
drivers/intel/gma is used in some capacity on all platforms that load a
VBT, while soc/intel/common's VBT code is for use with FSP.
BUG=b:79365806
TEST=GOOGLE_FALCO and GOOGLE_CHELL both build, exercising both affected
code paths.
Change-Id: I8d149c8b480e457a4f3e947f46d49ab45c65ccdc
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/26039
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I90e1d8b9f8e37bec8fc2796637b4548ea17e076b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch adds subsystem_id for eve as 0x006B. The value
is set in nhlt structure which will be used by endpoints as well.
Change-Id: Id6910678c4d6e92ed45c776f174855efd26f9e27
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/26139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change:
1. Allows mainboard to add OEM table to CBFS
2. Provides mainboard specific smbios_mainboard_manufacturer that reads
OEM ID from EC using CBI and compares it against the OEM ID in CBFS
table to identify the right OEM string.
BUG=b:74617340
Change-Id: Iff54b12745de3efa7be0801c9a3a9f2a57767dde
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I8e549e4222ae2ed6b9c46f81c5b5253e8b227ee8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use SUPERIO_DEV for global control device instead of DUMMY_DEV.
Change-Id: If3555906d359695b2eae51209cd97fbaaace7e61
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/25852
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
From coreboot side, include DMIC 4ch NHLT configuration and its
DMIC blob. In OS side, cras picks the needed channels using UCM's
channel map configuration.
So, this patch updates to include DMIC 4ch config.
BUG=b:79158926
TEST=Verified 4-ch record with arecord
TEST=Also verified internal mic record with cras using
'cras_test_client --capture_file dmic.raw --rate 48000
--num_channels 2 --duration 10'
Change-Id: Ic6df00c2f26ad9cdf54152ab021c2b10499c429c
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch uses GPIO macro to define rt5663 headset codec's irq as
ExclusiveAndWake. This change allows jack detection even when
device is in D3 state.
TEST=Plug in/out jack when the system is in deep sleep and wake up
the system to ensure that jack insertion/removal is detected.
Change-Id: Icb72337025a8408ed7ea9b6e60e938dcb88eae76
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/26016
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change OEM ID values to 6 characters to fix error compiling with IASL
version 20180427.
Also update table creator to 8 characters from 7.
Change-Id: Id6c9a7b08dc4a9efeb69011393e29aa5a6bc54c4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This gpio should be active low, but is not currently configured that way.
Changing gpio configuration to reflect that.
BUG=b:73121017, b:77941823
BRANCH=None
TEST=iotools mmio_read32 0xfdae0588 (GPP_E1) Make sure that when pen
is ejected, gpio is low and when pen is inserted, gpio is high.
Also tested that wake upon pen eject is working.
Change-Id: Ic49eea6412c3378dca39a3338b43df12bc27037d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26017
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using da7219 mclk-name property, oscout system clock is linked
to da7219 mclk. da7219 then handles enabling/disabling of the clk.
BUG=b:74570989
TEST=Tested clock enable/disable in kernel driver
Change-Id: I298b0ce5d2c40daadeb5d68f9cb595a965272021
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This reverts commit edf2f59b1d93a1bc9161a67d3c00a9a05fa8519a.
(google/kahlee: Resume on AC insertion)
The requirement to wake on AC insert is just to wake enough to charge,
not to wake the entire system.
BUG=b:77602394
TEST=None
Change-Id: I0ee709183b1605c1efc0fce673db512fac66adfa
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26014
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's very confusing trying to find the google platform names, because
they seem all unsorted in Kconfig. They're actually sorted according
to the variant name, but previously, that was impossible to tell.
- Add a comment to the top of variants in Kconfig.name
- Inset each variant name. If you start a prompt with whitespace,
it gets ignored, so after trying various ways to indent, the arrow
was the option I thought looked the best.
It now looks like this:
*** Beltino ***
-> Mccloud (Acer Chromebox CXI)
-> Monroe (LG Chromebase 22CV241 & 22CB25S)
-> Panther (ASUS Chromebox CN60)
-> Tricky (Dell Chromebox 3010)
-> Zako (HP Chromebox G1)
Butterfly (HP Pavilion Chromebook 14)
Chell (HP Chromebook 13 G1)
Cheza
*** Cyan ***
Change-Id: I35cb16b040651cd1bd0c4aef98494368ef5ca512
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- Add raydium controller
- Update elan controller with reset and enable GPIOs.
- Enable 'probed' so Linux will check which controller is being used.
BUG=b:78929054
TEST=Both elan and raydium touchscreen controllers work
Change-Id: I3bd9912a4b1edc7bf1075cb649afa3eab5dca458
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25998
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The _SB.DPTF.TPET ACPI code attached to EC_ENABLE_TABLET_EVENT doesn't
exist in the apollo lake code. Remove it from reef as part of the
cleanup to update to the new version of IASL.
This was in commit 4f803ac28f4 (mainboards/google/reef: Add support for
tablet mode switch.)
Change-Id: Ic10c418ddc708c1aed87ad4a9861f04d32445116
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25982
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set SPI Fast Read to 100MHz and Dual Read IO mode to speed up
the boot process by over a half second. Also, increase the Normal
Read speed to 33MHz as supported by the W25Q128FW.
BUG=b:70558952
TEST=Run cbmem -t to get boot times.
Change-Id: I616a96526ed90bb4ab0c9c6b78787799faa02633
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable this driver along with power saving.
BUG=b:73726008
BRANCH=none
TEST=boot and see this message:
BayHub BH720: Power-saving enabled 110103
From linux:
$ iotools pci_read32 2 0 0 0x90
0x00110103
Change-Id: I850e923f73e01fe629d66ad61b65afa58035845c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently, we've set TOUCHSCREEN_DIS gpio to disabled. Enabling
through ACPI. Set reset/enable/stop_off_ms variables to get timings
of power off sequence correct.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Ib1543f41f24cbe8c33aeb02e6aa43fd3dd977ed4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Changes in pin usage between yorp and bip
- LTE_OFF_ODL pin moved from GPIO_161 to GPIO_66
- I2S0 interface is not used in bip. It was used in
yorp for DMIC Wake on Voice through Nuvoton EC.
Also fix both bip and yorp pin settings for
LTE_OFF_ODL (Enable LTE and add an internal pull up).
Internal pull up can be removed later when sub-board (which
will have an external pull up for this signal) is available.
BUG=b:77869623
BRANCH=none
TEST=Build coreboot for octopus.
Change-Id: I8907bd63a43c4bc51ca991c3ec7c1cae9e39e2d1
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a new variant of poppy for the nocturne board.
Key differences from baseboard include:
- GPIO changes
- devicetree.cb changes
- memory stuffing option changes
BUG=b:78122599
BRANCH=none
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I11c7829041b3c45407c17f71b08cc7fc17f717e8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:74595037
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. check touchpad function
3. evtest
/dev/input/event5: PNP0C50:00 06CB:CD84
Change-Id: I47cb1b13881f0d52860f0afe4bbca7483409de54
Signed-off-by: ivy_jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25913
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the thermal event handler method TEVT is defined as an extern,
then defined again in platforms with thermal event handling. In newer
versions of IASL, this generates an error, as the method is defined in
two places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
Change-Id: I64dcd2918d14f75ad3c356b321250bfa9d92c8a5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This configures GPP_A23 as a wake source for the trackpad. We also
need to set up GPP_A GPE0_DW0, thus evicting GPP_B. We don't have any
interesting signals in GPP_B, so we won't be missing it.
I don't have hardware with A23 wired up, so i just tested the wake
source using A19 which is essentially identical to A23.
BUG=b:78541883
TEST=verified we can trackpad can wake system from suspend
Change-Id: If800464c8b2319d758b1823850571919f85bdc6c
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This creates a phaser variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:78572180
TEST=None
Change-Id: Ia03e8af91741f1f7aa3a42ac28688b8b6a708932
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Save FSP provided memory HOB info as SMBIOS Table-17 format.
Firmware tools such as mosys, dmidecode uses SMBIOS Table-17 to
report memory metadata.
BUG=b:78651920
TEST=Build for Octopus and check 'dmidecode -t17' and
'mosys memory spd print all' to verify dimm info.
Change-Id: I9b032b766a2927725b2378f7f720644d4459f602
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/25881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With only one entry for Write Protect gpio in the OIPG package, the sysfs
entry /sys/devices/platform/chromeos_acpi/GPIO.x is created as "GPIO"
instead of "GPIO.x". This was causing crossytem to return error for wpsw_cur.
BUG=b:78009842
Change-Id: Ica60f342420d95d09a45580f2f940443c03601de
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/25892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change configures a weak internal pull-up on ESPI_IO1 line for
octopus baseboard and variant bip. ESPI_IO1 is used as ALERT# line and
is expected to be open-drain. However, there is no external pull on
this line and so an internal pull-up is required to ensure proper eSPI
communication.
BUG=b:78497502
TEST=Verified that there is no eSPI communication failure between AP
and EC during boot-up and on suspend/resume.
Change-Id: Ic494aa7397b94bfd233ce10da8287660997b3377
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
|
|
Remove VBOOT_VBNV_CMOS from the mainboard. It is selected in the
stoneyridge Kconfig.
BUG=b:77347873
TEST=Manually clear CMOS and check coreboot restores VBNV from flash.
Change-Id: I30e517e06ab9d8f7d4a93bf82f12726756c44966
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add RW_NVRAM area to FMAP for VBOOT_VBNV_CMOS_BACKUP_TO_FLASH support.
BUG=b:77347873
TEST=Manually clear CMOS and check coreboot restores VBNV from flash.
Change-Id: Id8c6f54634b94bf6ae3755a827e80d0862a42dd2
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|