| Age | Commit message (Collapse) | Author |
|---|
|
This is a vboot feature, not a ChromeOS one, and unless selected by
vboot, compilation will fail in the non-ChromeOS + vboot build case.
TEST=build/boot skyrim w/vboot, w/o ChromeOS
Change-Id: If9a5343907457bf3319f045262fdddf7eae2f1cb
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67995
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a vboot feature, not a ChromeOS one, and unless selected by
vboot, compilation will fail in the non-ChromeOS + vboot build case.
TEST=build/boot guybrush w/vboot, w/o ChromeOS
Change-Id: I3108bcc8dfeacd99c9f5d36bd915d590292fef00
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67994
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This area relates to storing of AP RO verification information.
CONFIG_VBOOT_GSCVD is enabled by default for TPM_GOOGLE_TI50 and
guybrush is using TPM_GOOGLE_CR50.
Signed PSP verstage has the FMAP embedded. Since CB:67376 shifted the
RO section up by 8K, they were misaligned. Hence marking this area as
unused instead of removing the same to work around ChromeOS
infrastructure shortcoming.
Signed-off-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Change-Id: Id852e5b5c1f777992a96a75143757f4df8d975b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67901
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTC and No Battery Mode for Skyrim. This allows Skyrim to boot
without a battery or with a critically low battery.
DPTC remains disabled for the Winterhold and Morthal variants until it
can be tested on those boards.
BRANCH=none
BUG=b:217911928
TEST=Boot skyrim with low & no battery
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Icc4084476916cc8e142908d8e58baf7124568b8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67211
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the TPM I2C freqeuncy to 1 MHz for nivviks and nereid, and in
the baseboard. Other nissa devices will be changed after verification.
This saves 11 ms of boot time on nivviks and nereid.
400 kHz:
504:finished TPM initialization 272,304 (35,730)
...
512:finished TPM PCR extend 526,250 (23,729)
513:starting locking TPM 526,250 (0)
514:finished locking TPM 535,106 (8,855)
6:end of verified boot 543,927 (8,821)
1 MHz:
504:finished TPM initialization 266,293 (30,747)
...
512:finished TPM PCR extend 513,711 (20,108)
513:starting locking TPM 513,711 (0)
514:finished locking TPM 521,311 (7,599)
6:end of verified boot 528,893 (7,581)
BUG=b:249201598
TEST=On nivviks and nereid, all timing requirements in the spec are met.
Frequencies:
nivviks - 972.01 kHz
nereid - 968.99 kHz
Change-Id: I9dd783527d4215ed7d79d69853a1f321ea2d8a28
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Disable the external 1.05v VR in S0 as a fix for the
Display flicker issue in ADL-N.
Please refer the Doc with ID 742988 for more details.
BUG=b:248249033, b:245970842
TEST=Verified that the display flicker issue is fixed.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Iaa53bfd99a550b2cffcdaee640ee3a429e93aef7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Commit c7204b5a4 [mb/google/guybrush: Enable backlight in the OS]
disabled the GPIO for the display backlight in favor of using ACPI
to enable it, but this breaks display output for payloads which do
not/can not enable the backlight GPIO themselves (edk2, grub, SeaBIOS).
Re-enable the GPIO for display backlight so that payloads other than
depthcharge work properly.
TEST=build/boot google/dewatt with Tianocore payload, verify payload
display visible.
Change-Id: I2519d779954ed89486045aa7de0b18f1c31a4374
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch de-selects EC software sync config and enable early
EC Software Sync.
BUG=b:248775521
TEST=Able to perform EC sync on Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6bf8018e8a3fd06bb98c82a27d12883fc8d3a5db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Rename so table more indicative of when GPIOs are set, and so it can
be used for more than just setting PCIe GPIOs.
Rename the getter function to match.
Change-Id: I285602209072247895c2cb0830f3faf675328757
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: Icebf7e11736929389227063039575a4c5ecf3840
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch adds ACPI configurations of 8MP YHUX and 2MP CJFKF28-1
as world- and user-facing cameras of Rex.
BUG=b:246413264
TEST=Verified world- and user-facing cameras using Chrome Camera App on
Google/rex device.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Iaaa16e491a66500606b3a9eb1d87f396641778e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
According intel Doc#634254 and Doc#608715
PS2/PS1 cross point = 5
PS1/PS0 cross point = 10
PS2 cutoff = 1.4*(PS2/PS1 cross point) = 7
1.3 is better magnification, it obtain by test
PS1 cutoff = 1.3*(PS1/PS0 cross point) = 13
BUG=b:241850120
BRANCH=brya
TEST='FW_NAME=vell emerge-brya coreboot'
Change-Id: I83e9682004e2c3644ad4a5565e6ab85be48ba22f
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Xivu uses PCIE WLAN, so disable the CNVi WLAN/BT.
BUG=b:247120749
TEST=Boot to OS on xivu and check that WLAN/BT still works.
Change-Id: I968d383278bd50268d899cff82067ceb7c3ba5ed
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Ben Kao <ben.kao@intel.com>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: I17db734784ce96cdf5e0486dc2ad057d73bfb15f
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Rather than duplicating the entire set of GPIOs from the baseboard, use
the variant_override_gpio_table() method like all other octopus
variants do.
TEST=build/boot ampton, dump GPIOs and verify unchanged.
Change-Id: I36aa25bbee7c21a51d9fdd40405f492082455d9c
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67803
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for the following two new memory parts to support a new
SKU that has two memory options that brya0 does not have:
MT53E2G32D4NQ-046 WT:C
MT53E512M32D1NP-046 WT:B
BUG=b:248126749
TEST="emerge-brya coreboot chromeos-bootimage", flash a skolas with
an image-brya0.serial.bin and verify it boots successfully to kernel.
Change-Id: I28667918e5a183339febdc054465effeac8bddbe
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67879
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: I11814016d654bc2c2e6d24b3d18fb30d5b843fe9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: Id1e1a67608454466dc65bf4c4985cf4eba84c97d
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: Ib8439e664defeafd2d08cffb74c997ab69230231
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: Iaa3c9404919fd6c43596d7b27cfab43a1a5b0b21
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch selects the SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES to allocate
TBT/USB4 root port resources for PCIe tunneling.
BUG=b:248328015
TEST=Built image and verified TBT/USB4 tunneling functions on Rex.
Change-Id: I69f4d26bb7b3d74dbda068add284a69f1bbeff40
Signed-off-by: zhaojohn <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
In order that GPP_H13 not use the GPIO override programming from its
baseboard (brya), explicitly program GPP_H13 to a output HIGH instead
of relying on the 20K pullup from the baseboard.
BUG=b:240617195
TEST=SSD still functional
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iddedebe2d5cfc0123932b14980d1268bcb147703
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
The next rev of this board will move the dGPU PEXVDD enable pin from
GPP_E10 to GPP_F12. This patch handles both the old and newer revisions
by using an ACPI Name to hold the GPIO # for PEXVDD enable. It also
cleans up the GPIO handling a little bit between board revs.
BUG=b:242752623
TEST=dGPU is functional and power sequencing tests still pass on board
rev 2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Icc7968777f86ab07561b0a861b7d22ec714d1c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
On Banshee, when the privacy switch is toggled the camera is
disconnected. Which means that we will never be able to tell the user
that the privacy switch is enabled when the camera is on, making the
virtual control unusable.
Remove the description.
BUG=b:248219472
BRANCH=firmware-brya-14505.B
TEST=none
Change-Id: I1a241bd889c0c1aae039510a0620748b2f7a6806
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Modify GXTP7863 generic.irq to generic.irq_gpio.
BUG=b:245082617
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: Iaf6cc6010132d5b33b06909ceb1069115a911b48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This reverts commit 1a8eb6c02103727431ac1ea23f4f507e49f3cde7.
Reason for revert: migrating to the 32MB AP Firmware hence, need to
revert this CL.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibea1ad0cff008f9391cbda9e51899557b1e9c979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
'Mendocino' was an embargoed name and could previously not be used.
Update references for consistency with the correct naming convention.
BUG=b:245727030
TEST=builds and boots to kernel
Cq-Depend: chrome-internal:4878294
Cq-Depend: chromium:3763392
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Ic0248a872dfc92486658aa9bd92bed755dbf59d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67750
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BIOS_ERR is inappropriate since the init message is informational.
Use BIOS_INFO instead.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I6fc15291a6d177a1b9e258d08e165224e5e10b32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67733
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
EN_PP3300_EMMC has be changed to GPP_A21 for DP++ and it based on Moli GPIO Table_20220803.xlsx, so update enable_gpio for emmc_rtd3 by board_ver.
BUG=b:241370405
TEST=emerge-brask coreboot
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I129706861fd1fcf061371ce94352331ef44359d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67736
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently the `pch_pirq_init()` function in lpc_lib.c will program
PIRQ IRQs for all PCI devices discovered during enumeration. This
may not be correct for all devices, and causes strange behavior
with the Nvidia dGPU; it will start out with IRQ 11 and then after
a suspend/resume cycle, it will get programmed back to 16, so the
Linux kernel must be doing some IRQ sanitization at some point.
To fix this anomaly, explicitly program the IRQ to 16 (which we
know is what IRQ it will eventually take).
BUG=b:243972575
TEST=`lspci -vvv -s1:00.0|grep IRQ` shows IRQ 16 is programmed
at boot and stays consistent after suspend/resume.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I66ca3701c4c2fe5359621023b1fd45f8afd3b745
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67746
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to Nvidia, the GC6 flag (DFEN) should not get cleared after
a successful GC6 entry; the kernel driver will not re-inform ACPI
that the exit should be GC6 exit as well.
BUG=b:243888246
BRANCH=brya
TEST=tested by Nvidia
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I220795928d03f269de48278ea0ab57de7253fad5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67745
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The hatch and puff baseboards have diverged enough to where it makes
more sense to split them into separate boards. Copy the mb/google/hatch
directory into a new dir 'puff' and strip out all boards and items
related to the hatch baseboard. Remove all puff-related items from the
original hatch directory. Clean up and alphabetize Kconfig selections.
Test: build and boot akemi hatch variant and wyvern puff variant.
Change-Id: I8c7350f3afcff3ddefc6fa14054a3f9257568cd3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62970
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All cherry boards (tomato, dojo) share the same SKU ID encoding, in the
sense that a device has NVMe storage if and only if the BIT(1) of SKU ID
is set (otherwise eMMC). Therefore, instead of hard coding the list of
NVMe (PCIe) SKU IDs, we check the BIT(1) to decide whether to initialize
PCIe.
In addition, in preparation for UFS devices coming in the future,
reserve BIT(3) (which is unset for all of current SKUs) for them.
BUG=b:237953117, b:233327674
TEST=emerge-cherry coreboot
BRANCH=cherry
Change-Id: I9b30338645a87f29f96a249808b90f1ec16f82df
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Set tcc_offset value to 1℃ in devicetree for Thermal Control Circuit
(TCC) activation feature. This value is suggested by Thermal team.
BUG=b:246913963
TEST=USE="project_crota project_brya" emerge-brya coreboot
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: Ie2f60bed34fbd6fa3624be60138511a22b199a8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch makes dedede EC wake up AP from s0ix when the state of
charge drops to low_battery_shutdown_percent.
Demonstrated as follows:
1. Boot OS.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 4.
4. System resumes.
BUG=b:244253629
TEST=Verified on dedede
Change-Id: I39234d2b9e739383b5f96be49077f8c9831fa0fa
Signed-off-by: Ivan Chen <yulunchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Skolas board is based on Raptor Lake SoC, not Alder Lake. The code
change sets CPU power limit values as performance configuration based
on various Raptor Lake SoC SKUs as per the document #686872.
BUG=b:242869605
BRANCH=None
TEST=Built and tested on skolas board
Change-Id: Ieb3ca4ff77039412ef56da49e1b438f5e0b9db02
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable ddc on DDI_PORT_2 for support DP++.
BUG=b:240382609
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I475e3c0278cfa92ab40ad84f6da580b4cded9933
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add a variant specific S0ix hook to fill the SSDT table to disable and
enable camera during suspend and resume respectively.
BUG=b:206911455
TEST=Build Boten BIOS image. Ensure that camera is disabled during
suspend and enabled during resume.
Change-Id: I3229b22b8d8651bf2d9df25b10ce6749efde7cf6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
Add FM350GL 5G WWAN support using drivers/wwan/fm and additional PM
features from RTD3.
BUG=b:244077118
TEST=check cbmem -c
\_SB.PCI0.RP06: Enable RTD3 for PCI: 00:1c.5 (Intel PCIe Runtime D3)
\_SB.PCI0.RP06: Enable WWAN for PCI: 00:1c.5 (Fibocom FM-350-GL)
check PXSX Device is generated in ssdt.
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6114c589769d2eca882cf1a5255cf4c5937121a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add new ram_id:3 (0011) for memory part K3LKCKC0BM-MGCP.
DRAM Part Name ID to assign
K3LKCKC0BM-MGCP 3 (0011)
BUG=b:247039096
TEST=Use part_id_gen to generate related settings and
emerge-nissa coreboot
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I78d2e501b9d8d801a3d149002f638125bf4275f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Modify config settings based on new module KBAE350 spec
BUG=b:245640845
BRANCH=None
TEST=Build and boot on skolas
Signed-off-by: AlanKY Lee <alanky_lee@compal.corp-partner.google.com>
Change-Id: I8a9bee9bb79bda4e3f1d259716844b42a7fce397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jimmy Su <jimmy.su@intel.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Add the Low/No Battery Mode DPTC values for Skyrim.
These values were generated by AMD.
BRANCH=none
BUG=b:217911928
TEST=Build skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I5f277761cb7379b4344492f95010d8d5ddd689fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67693
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the Normal Mode DPTC values for Skyrim.
These values were generated by AMD.
BRANCH=none
BUG=b:217911928
TEST=Build skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I1e1f55b941f3e70aad33d55a90fb012eac3ba12d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67690
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ELAN6918 Power Sequencing seems not perfectly matching
with the previous platforms and setting GPP_C06 to high prior
to the power sequencing is actually makes it work.
Ideally Power Sequencing should be as below for ELAN6918 (in ACPI)
`POWER enabled -> RESET deasserted -> Report EN enabled`
But below sequence is only working currently:
`Report EN enabled (ramstage) -> POWER enabled (ACPI) -> RESET
deasserted (ACPI)`
BUG=b:247029304
TEST=Verified ELAN touch panel is working as expected after booting
Google/rex device to ChromeOS.
Change-Id: Ideaeb0faa882b8e603534bbface51ea76923d436
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
The brya4es variant is no longer needed, removing code for brya4es.
BUG=b:246611270
TEST=None
Change-Id: I9b222f89fe766c63158518713be19d7959451721
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Enable nau8825 ADCOUT to make I2S signal meet spec.
BUG=b:234789689
TEST=I2S waveform can meet spec timing.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I7ea472ac4e4add4e790b9b3fbb6becd40665eb1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
TEST=Able to build and boot the Google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iae5317b24856ef2cbd2f36cc28f645826536c21a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Moving the config value SOC_AMD_COMMON_BLOCK_ACPI_DPTC to
soc/amd/picasso/Kconfig and conditionally enabling it for only Morphius
boards makes the value dptc_tablet_mode_enable redundant.
This CL removes dptc_tablet_mode_enable so DPTC is controlled entirely
with the Kconfig value SOC_AMD_COMMON_BLOCK_ACPI_DPTC. This means DPTC
is only included for boards that actually enable it.
BRANCH=none
BUG=b:217911928
TEST=Build zork
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ic54a9bb491234088be8184bec8b09e2e31ffa298
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BIOS_ERR is inappropriate since the message is informational.
Use BIOS_INFO instead.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I91be3f47ae93c8262e430a06cacec3d2c29ebd58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Move enabling SOC_AMD_COMMON_BLOCK_ACPI_DPTC from
soc/amd/picasso/Kconfig to mainboard/google/zork/Kconfig and
conditionally enable it only for Morphius boards.
This reduces which boards/variants have DPTC enabled to only those that
actually use it.
BRANCH=none
BUG=b:217911928
TEST=Build zork
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Iddebcf5dbadae135c8110e2afd9ad76ef7dcc09d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67637
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This file is neither included in the build nor correct, since the
Stoneyridge SoC doesn't have a legacy PCI bridge on bus 0 bridge 0x14
function 4.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0daed891984faed9fbc36f0215edfc56e0ae14a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
As of commit 2cf52d80a6ec ("mb/*/{device,override}tree: Set touchpads to
use detect (vs probed) flag") all touchpads in the tree have been
switched from using the 'probed' flag to 'detect.' Winterhold was added
in between the time that patch was pushed and merged, so switch these
instances over too.
Change-Id: I34e1265ecd6409f720ae486926c5078f626fc693
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67487
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn off the LAN power which is controlled by GPP_A10 in S0ix states.
For an USB device, the S0ix hook is needed for the on/off operationas
to take place.
BUG=b:245426120
BRANCH=firmware-dedede-13606.B
TEST=emerge-shotzo coreboot
check LAN LED off in S0ix states
check LAN function ok after suspending 500 loops
check SSDT table has MS0X entry
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One))
{
\_SB.PCI0.CTXS (0x41)
}
Else
{
\_SB.PCI0.STXS (0x41)
}
}
}
Change-Id: I3fcab4a73239b4f006839c0c81e9b4cc74047b77
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
To improve boot time, raise little CPU from 500MHz to 2GHz at romstage
(before DRAM calibration).
FW logs:
Check CPU freq: 1999968 KHz, cci: 1600012 KHz
TEST=cpu freq and cci freq run correctly.
BUG=b:244251006
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: Ic1bed53669baa15f797c9a952455376a39d29cf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67544
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mono_time is now 64-bit, the utility functions interfacing with
mono_time should also be 64-bit so precision isn't lost.
Fixed build errors related to printing the now int64_t result of
stopwatch_duration_[m|u]secs in various places.
BUG=b:237082996
BRANCH=All
TEST=Boot dewatt
Change-Id: I169588f5e14285557f2d03270f58f4c07c0154d5
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
BUG=b:232573696
TEST=Able to verify audio playback on Google/Rex with this change.
Change-Id: Ia8dfc79e7e4d27828726145156c870733d716899
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66919
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:245426120
BRANCH=firmware-dedede-13606.B
TEST=emerge-dedede coreboot
check SSDT table has MS0X entry
Scope (\_SB)
{
Method (MS0X, 1, Serialized)
{
If ((Arg0 == One)) {}
Else
{
}
}
}
Change-Id: Id01089531503e62231c5ab19e4cd8056198b9acb
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add the 'detect' flag to the Elan touchpad, so coreboot can determine
which touchpad type is present at runtime and generate the correct
ACPI entry for it (the Synaptics touchpad already has the flag).
Test: build/boot google/nami, verify touchpad works under Linux/Windows
Change-Id: I437d1d470552d55496dfe611f441331127c64250
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Problem: OTA is triggering warmboot, where DDR is
in self-refresh mode. Due to which DDR training
is not going well.
Change: Verify reboot type in case of OTA. If it is warmboot, will
force for cold boot inorder to trigger DDR training
BUG=b:236990316
TEST=Validated on qualcomm sc7180 development board.
Test observation: Cold boot is triggered forcefully,
if current reboot is warmboot in case of OTA
Signed-off-by: Venkat Thogaru <quic_thogaru@quicinc.com>
Change-Id: I908370662292d9f768d1ac89452775178e07fc78
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67406
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Kconfig options for ASPM.
TEST=Verify ASPM is enabled with `lspci -vvv`, `suspend_stress_test -c
10` passed all 10 times
BUG=b:243771794
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I54071d9c9607da4561d745d152924d56904c0fee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Update ASPM configuration, disabling ASPM for the SSD due to s0i3
issues. Bug b:245550573 created to track the SSD issue.
TEST=Boot to OS and verify suspend via `suspend_stress_test -c 10`
BUG=b:243771794
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I45a290c8ceddd39f65c6fe1390e3a753cad99899
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I4ccdd370d3e9aef938fae4c4690ec0bf4c53c500
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Linux always "turns on" a PowerResource when it boots, regardless of
_STA, so the _ON routine should be idempotent. In this case, it all is,
except for the LTR restore, which would restore a value of 0 when _ON is
run the first time, which means that LTR is disabled on the root port
from then on, as the save/restore routines will keep saving/restoring
that 0. THis patch fixes the problem by moving the power checks from
PGON/PGOF to GCOO/GCOI.
BUG=b:244409563
TEST=boot agah and verify that LTR is still enabled on the root port
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I4ed78323608eede5b8310598f1f1115497ab2b5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67278
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
The Linux kernel runtime D3 framework expects a PCIe device to have a
power resource in order to be properly power-manageable. The _PR0/_PR3
values were pointing at the PEG0 Device, which is not a PowerResource,
so this must have confused the RTD3 framework and RTD3 was not
functional. Removing the _PR0/_PR3 fixes the problem.
BUG=b:243888246
TEST=echo auto > /sys/bus/pci/devices/0000:01:00.0/power/control;
sleep 10;
echo on > /sys/bus/pci/devices/0000:01:00.0/power/control
After this there are no longer errors seen in dmesg about failing
to place the device into D0.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I83fa1e5fabd3257b097c10e7a13c9861872685ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Mostly there are too many extraneous `\_SB.PCI0.` prefixes, also a few
minor cleanups, but nothing functional.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I79d919d2f04f57232f8f6a4e4d0690833faeb834
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Similar to the prior CL (commit db8ad5e), do the same register dance
before/after GCOFF.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8fecba40c5a5af11e24f82db07face3ce10481bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67086
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.corp-partner.google.com>
Reviewed-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor AMD DPTC tablet mode in preparation for adding low/no battery
DPTC settings.
1. Refactor and simplify acpigen_write_alib_dptc() into the following
functions:
- acpigen_write_alib_dptc_default()
- acpigen_write_alib_dptc_tablet()
2. Add device tree register value dptc_tablet_mode_enable to control
whether DPTC tablet mode is enabled for a variant.
3. Add dptc.asl to perform the necessary ACPI checking before modifying
the DPTC settings.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build nipperkin
TEST=Boot skyrim
Change-Id: I2518fdd526868c9d5668a6018fd3570392e809c0
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Lists of GPIO PINS being updated:
SPKR_INT_L_R
RST_HP_L
SOC_HDMI_HPD_L
SOCHOT_ODL
SOC_FPMCU_INT_L
EN_PP3300_WLAN
BUG=b:24410269
TEST=Build and boot Google/Rex to ChromeOS.
Change-Id: If2fb354f931217c09a6c1c81ca780cb121b24468
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67449
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable touchpad for Google Rex.
BUG=b:245866939
TEST=Build and boot to Google Rex. Verify touchpad works.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I49fdd72bf3350085e82411b95edcd6a9a09d2df5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67471
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
|
|
Add GPE route for GPP_B.
BUG=b:245866939
TEST=Build and boot to Google Rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I28066a6cc75908f8ceefbdbf8c088c56833606ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add functionality such that the FPMCU is power cycled and has its reset
sequenced on boot.
This has been added such that we do not need to update the bootblock.
We are required to do this as bootblock exists in read-only flash for
devices that have already been manufactured and so have no method of
updating the sequencing there.
Power remains off during coreboot (after briefly being turned on in the
unchangeable bootblock).
Once control is handed over to the Kernel, it takes care of sequencing
the power and reset appropriately and ensures the FPMCU is unpowered for
>200ms on boot.
BUG=b:240626388
TEST=Confirmed FPMCU is still functional on Vell and Anahera.
Confirmed power is off for approximately 6 seconds on boot (target
>200ms).
Confirmed reset is de-asserted approx 5ms after power application
(target >2.5ms)
Change-Id: I9694f8837e0a72eaed42a5eeee92b0f120269086
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66915
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TEST=Boot to OS on nivviks/nirwen and check that stylus GPIOs are
configured based on fw_config.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ibbe9f379abe10a741642e11d4833d3a53489693a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66929
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Config I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
EE measured touchscreen/audio runs at 385.5/397.9kHz after tuning.
BUG=b:244403643
BRANCH=firmware-dedede-13606.B
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: I7d9503e5f92295432e31f09ae791eaa18eac9d4d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that the driver skips
initial probe during kernel boot and prevent privacy LED blink.
BUG=b:194979741
BRANCH=firmware-brya-14505.B
TEST=Build and boot skolas to OS. Verify entries in SSDT.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3c32dd71ab454227b15913bda7f542230e5568db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Historically, ChromeOS devices have worked around the problem of OEMs
using several different parts for touchpads/touchscreens by using a
ChromeOS kernel-specific 'probed' flag (rejected by the upstream kernel)
to indicate that the device may or may not be present, and that the
driver should probe to confirm device presence.
Since c636142b, coreboot now supports detection for i2c devices at
runtime when creating the device entries for the ACPI/SSDT tables,
rendering the 'probed' flag obsolete for touchpads. Switch all touchpads
in the tree from using the 'probed' flag to the 'detect' flag.
Touchscreens require more involved power sequencing, which will be done
at some future time, after which they will switch over as well.
TEST: build/boot at least one variant for each baseboard in the tree.
Verify touchpad works under Linux and Windows. Verify only a single
touchpad device is present in the ACPI tables.
Change-Id: I47c6eed37eb34c044e27963532e544d3940a7c15
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67305
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch enables AC plug/unplug for resume.
BUG=b:188457962
BRANCH=grunt
TEST=Verified AC plug/unplug wakes up Treeya.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I10480f8224b909fefe42d46d7c03fc9d3fe5abfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch enables AC plug/unplug as resume signals.
BUG=b:188457962
BRANCH=Zork
TEST=Verified AC plug wakes up Ezkinil.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: Ib1af6ff9f18544ec6a86e34588fb4d9e8cd3bab2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Follow the Thermal_paramters_list-0902.xlsx to modify DPTF parameters
and fan table.
1. Modify CRT of TSR0 - TSR3 to 97.
2. Modify TCC offset to 6.
3. Update new fan table.
BUG=b:244657172
TEST=emerge-brask coreboot
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I751bc5442f64428c383034755cd5d74fbd0ea91e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67314
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify fan speed/duty table follow "Duty table.xlsx".
BUG=b:244262869
TEST=Boot to ChromeOS. Using SDV system, enter duty value, and then
system feedback fan speed.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Id5e885b96624d5fc31f1d42e3582c3ab01e08458
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The PCIe WWAN module used on rex requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WWAN_RST#, then WWAN_PERST# in ramstage
BUG=b:244077118
TEST=FM350 could be enumerated via lspci
Measured signals to check start-up Timing Sequence, tpr/ton1/ton2.
Tpr = 572mS
Ton1 = 6.3s
Ton2 = 6.3+4.17ms
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I6cda9348ef7f54efe5ba2358040596a1c2da1b13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67332
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This area relates to storing of AP RO verification information.
CONFIG_VBOOT_GSCVD is enabled by default for TPM_GOOGLE_TI50 and
guybrush is using TPM_GOOGLE_CR50.
Signed-off-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Change-Id: I896b871bf2ac64e334514b979add9b8ac2c43945
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
|
|
Change the name of the CALIBRATION_REGION definitions used in two
separate locations. This conflict was causing an error for the
lint-001-no-global-config-in-romstage test.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6734f2a7d9be669586ea350fb9979fcd422b591
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
dptc_enable is being treated as a bool, so convert to explicitly be a
bool.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build guybrush
TEST=Build skyrim
Change-Id: I0e93d892b3b8016221812c8b9ec6c257dcf13ef5
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67188
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pass the reset gpio parameter to BL31 to support SoC reset.
TEST=build pass.
BUG=b:233720142
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: Ifdfbd6bd82f64b084f6349cb617443053c89a3f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67357
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The implementations of register_reset_to_bl31() are the same for
MedaiTek platforms, so we extract them to soc/common/bl31.c.
BUG=None
TEST=build pass
Change-Id: I297ea2e18a6d7e92236cf415844b166523616bdf
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The T4 of ANX7625 power on sequence should be larger than 0ms, but it's
-59ms now. So add 70ms delay between DSI_TE and LCM_RST.
BUG=b:242352915
TEST=The sequence T4 is larger than 0ms when power on.
Change-Id: I6b888707ec3c0612e396564e77c4cdbe92614dc5
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: wen zhang <zhangwen6@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Initialize winterhold devicetree.
BUG=b:241196632
TEST=emerge-skyrim coreboot
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: I9fe224cdc2acb1f13d3bf9341b487892c15f8ea2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Follow FT6_SOC_GPIO_PM&Strap_20220815A.XLSX
update Gpio setting
BUG=b:240824497
BRANCH=None
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Change-Id: I2086c326cbf46ba6378d18d37dcbbe9fafa6b2bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GSPI0 pads required muxing to NF8. Support for extended
native functions was added in
commit b6c32d7fe4ea98ba8b3a10cb5ce46448801855b8
BUG=b:244610269
TEST=build and booted on Rex
Change-Id: Iab4e0bc6890cd8e976c513fe87dda0da9b5f2ee0
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
This project concluded and the coreboot implementation is no longer
required.
BUG=b:244596639
BRANCH=firmware-brya-14505.B
TEST=none
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: Ie647dac7ad4879ec1b11baa0a8cb0990af56852f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67299
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:244373677
BRANCH=firmware-dedede-13606.B
TEST=Build image and verified by thermal team.
Change-Id: I8415e0d25a79764f0c1d11688728b7caa3b3d6a4
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
elog_gsmi_cb_mainboard_log_wake_source is called from SMI and causes
eSPI transactions. If the SMI interrupts an ongoing eSPI transaction
from the OS it will conflict and cause failures. Removing this call to
avoid conflicts. This can be re-enabled after refactoring
google_chromeec_get_mask to use ACPI MMIO.
This is a copy of CB:63280 but for skyrim.
BUG=b:227163985, b:243557044
TEST=suspend/resume skyrim and no longer see EC wake sources in elog.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iac56840fe15101bc556d8cce9960f761c6ea7181
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Enable DSP setting. Make sure the SSP can work as expected.
BUG=b:243123156
TEST=Dev beep working on Rex.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I6ae28e414ac4ac33f596df57691c979eac5fe132
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67270
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Select SYSTEM_TYPE_LAPTOP so the FADT PM profile is correctly set to
mobile (vs the default of desktop).
TEST=build/boot google/dewatt, run FWTS and verify FADT PM profile correct
Change-Id: I480fbe85782e2c63efa8d2212d503a47d8149ab9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
As part of investigating b/240690391 I noticed that we were missing
the daughter board ports. Not all SKUs have these ports connected,
but it doesn't hurt to have the extra ACPI nodes.
BUG=none
TEST=build
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id6fc34acbfa30bc15e697043bf93bcf584256128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Nvidia recommends saving and restoring the LTR Enable bit in PCIe config
space for the PCIe root port before/after GC6 entry. Also the detectable
error bit should be cleared, as there may be errors expected during the
GC6 flow.
BUG=b:214581763
TEST=no more correctable errors after GC6 entry/exit
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I058ce1b3f17fb6cc59785a85efaf9ea0504cf2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
BUG=b:238937091
TEST=Dump SSDT on nereid and check that the wifi device contains the
DmaProperty. Also check that the kernel marks the device as untrusted.
Change-Id: I0725ea18d52420a3161d6fcfa3bcb72ebe35f3a5
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Compile-time support of DPTC is controlled by
EC_ENABLE_AMD_DPTC_SUPPORT in each variant's ec.h file. This CL removes
EC_ENABLE_AMD_DPTC_SUPPORT and replaces it with the Kconfig value
SOC_AMD_COMMON_BLOCK_ACPI_DPTC.
Each variant's run-time support of DPTC continues to be controlled by
the variant's overridetree.cb "dptc_enable" value.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ic101e74bab88e20be0cb5aaf66e4349baa1432e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Fix EC_IN_RW config for Rex. Dauntless on Rex does not have an EC_IN_RW GPIO pin.
Port of commit 7f339c6050c5 ("mb/google/corsola: Correct EC-is-trusted logic")
BUG=b:243950850
TEST=Built and booted to Google Rex.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I97e5c752b4f36c9221137903f755837880f6b1c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67208
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This reverts commit 47fee08fc3a383e14dc974754d6e463fa320badf.
The required EC changes are now in place to revert this W/A that
disables the LID based shutdown.
BUG=b:243920003
TEST=No shutdown request has triggered while booting AP at
depthcharge.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I5ae56912f030f6f0e3cb49282bbffc920fb389c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67206
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
