| Age | Commit message (Collapse) | Author |
|---|
|
- Add raydium controller
- Update elan controller with reset and enable GPIOs.
- Enable 'probed' so Linux will check which controller is being used.
BUG=b:78929054
TEST=Both elan and raydium touchscreen controllers work
Change-Id: I3bd9912a4b1edc7bf1075cb649afa3eab5dca458
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25998
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The _SB.DPTF.TPET ACPI code attached to EC_ENABLE_TABLET_EVENT doesn't
exist in the apollo lake code. Remove it from reef as part of the
cleanup to update to the new version of IASL.
This was in commit 4f803ac28f4 (mainboards/google/reef: Add support for
tablet mode switch.)
Change-Id: Ic10c418ddc708c1aed87ad4a9861f04d32445116
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25982
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set SPI Fast Read to 100MHz and Dual Read IO mode to speed up
the boot process by over a half second. Also, increase the Normal
Read speed to 33MHz as supported by the W25Q128FW.
BUG=b:70558952
TEST=Run cbmem -t to get boot times.
Change-Id: I616a96526ed90bb4ab0c9c6b78787799faa02633
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable this driver along with power saving.
BUG=b:73726008
BRANCH=none
TEST=boot and see this message:
BayHub BH720: Power-saving enabled 110103
From linux:
$ iotools pci_read32 2 0 0 0x90
0x00110103
Change-Id: I850e923f73e01fe629d66ad61b65afa58035845c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/25967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently, we've set TOUCHSCREEN_DIS gpio to disabled. Enabling
through ACPI. Set reset/enable/stop_off_ms variables to get timings
of power off sequence correct.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Ib1543f41f24cbe8c33aeb02e6aa43fd3dd977ed4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Changes in pin usage between yorp and bip
- LTE_OFF_ODL pin moved from GPIO_161 to GPIO_66
- I2S0 interface is not used in bip. It was used in
yorp for DMIC Wake on Voice through Nuvoton EC.
Also fix both bip and yorp pin settings for
LTE_OFF_ODL (Enable LTE and add an internal pull up).
Internal pull up can be removed later when sub-board (which
will have an external pull up for this signal) is available.
BUG=b:77869623
BRANCH=none
TEST=Build coreboot for octopus.
Change-Id: I8907bd63a43c4bc51ca991c3ec7c1cae9e39e2d1
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a new variant of poppy for the nocturne board.
Key differences from baseboard include:
- GPIO changes
- devicetree.cb changes
- memory stuffing option changes
BUG=b:78122599
BRANCH=none
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I11c7829041b3c45407c17f71b08cc7fc17f717e8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:74595037
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. check touchpad function
3. evtest
/dev/input/event5: PNP0C50:00 06CB:CD84
Change-Id: I47cb1b13881f0d52860f0afe4bbca7483409de54
Signed-off-by: ivy_jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25913
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the thermal event handler method TEVT is defined as an extern,
then defined again in platforms with thermal event handling. In newer
versions of IASL, this generates an error, as the method is defined in
two places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
Change-Id: I64dcd2918d14f75ad3c356b321250bfa9d92c8a5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This configures GPP_A23 as a wake source for the trackpad. We also
need to set up GPP_A GPE0_DW0, thus evicting GPP_B. We don't have any
interesting signals in GPP_B, so we won't be missing it.
I don't have hardware with A23 wired up, so i just tested the wake
source using A19 which is essentially identical to A23.
BUG=b:78541883
TEST=verified we can trackpad can wake system from suspend
Change-Id: If800464c8b2319d758b1823850571919f85bdc6c
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This creates a phaser variant for octopus. Nothing is set in the variant
files here; everything is picked up from baseboard.
BUG=b:78572180
TEST=None
Change-Id: Ia03e8af91741f1f7aa3a42ac28688b8b6a708932
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Save FSP provided memory HOB info as SMBIOS Table-17 format.
Firmware tools such as mosys, dmidecode uses SMBIOS Table-17 to
report memory metadata.
BUG=b:78651920
TEST=Build for Octopus and check 'dmidecode -t17' and
'mosys memory spd print all' to verify dimm info.
Change-Id: I9b032b766a2927725b2378f7f720644d4459f602
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/25881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With only one entry for Write Protect gpio in the OIPG package, the sysfs
entry /sys/devices/platform/chromeos_acpi/GPIO.x is created as "GPIO"
instead of "GPIO.x". This was causing crossytem to return error for wpsw_cur.
BUG=b:78009842
Change-Id: Ica60f342420d95d09a45580f2f940443c03601de
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/25892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change configures a weak internal pull-up on ESPI_IO1 line for
octopus baseboard and variant bip. ESPI_IO1 is used as ALERT# line and
is expected to be open-drain. However, there is no external pull on
this line and so an internal pull-up is required to ensure proper eSPI
communication.
BUG=b:78497502
TEST=Verified that there is no eSPI communication failure between AP
and EC during boot-up and on suspend/resume.
Change-Id: Ic494aa7397b94bfd233ce10da8287660997b3377
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
|
|
Remove VBOOT_VBNV_CMOS from the mainboard. It is selected in the
stoneyridge Kconfig.
BUG=b:77347873
TEST=Manually clear CMOS and check coreboot restores VBNV from flash.
Change-Id: I30e517e06ab9d8f7d4a93bf82f12726756c44966
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add RW_NVRAM area to FMAP for VBOOT_VBNV_CMOS_BACKUP_TO_FLASH support.
BUG=b:77347873
TEST=Manually clear CMOS and check coreboot restores VBNV from flash.
Change-Id: Id8c6f54634b94bf6ae3755a827e80d0862a42dd2
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change enables xDCI controller on poppy, nautilus and soraka.
BUG=b:78577893
BRANCH=poppy
Change-Id: I9b0f81bda889b822479ead4d1acc2b613151a304
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25849
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the SPI speed for Normal, Fast, AltIO, and TPM in bootblock.
This setup is needed when moving AGESA out of the bootblock. It sets the
SPI bus speed of the TPM access in verstage.
BUG=b:70558952
TEST=Boot with AGESA moved out of the bootblock.
Change-Id: Ida77d78eb1f290e46b57a46298400ed6c8015e2c
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/25756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch enables dptf for Octopus by adding dptf.asl in dsdt.asl.
BUG=b:74263914
BRANCH=None
TEST=None
Change-Id: I7194cdd2af88ff062ebcc92cc97b3cdc3d21ecd6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/25809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The grunt touchpad interrupt can be used as a wake source. For grunt,
the touchpad interrupt uses GPIO5 which corresponds to GEVENT7.
BUG=b:77602771
TEST=In OS: # cat /proc/acpi/wakeup
=> D015 S3 *enabled i2c:i2c-ELAN0000:00
TEST=powerd_dbus_suspend, touching touchpad (> 1 sec) wakes from S3.
Change-Id: I510642108a1257f6601f18c77cf3107573427f39
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25827
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The grunt EC uses GPIO24 (EC_PCH_WAKE_L) to signal wake-up events to the AP.
On Stoney, GPIO24 maps to GEVENT (GPE) 15.
The kahlee EC uses GPIO2 (EC_PCH_WAKE_L) to signal wake-up events to the AP.
On Stoney, GPIO2 maps to GEVENT (GPE) 8.
BUG=b:78461678
TEST=powerd_dbus_suspend, tap any key on keyboard wakes from S3.
TEST=sign in, EC: lidclose, EC: lidopen => system wakes from S3.
Change-Id: Ib1809740837e686992ff70b81933159a5dff7595
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
On the kahlee variant, EC_SMI_ODL is connected to GPIO6, which uses
GEVENT 10 (GPE10). Fix this up, and also clean up the EC_*_GPI
definition format a bit to match the format in the baseboard/gpio.h.
BUG=b:78461678
TEST=build coreboot for kahlee
Change-Id: I9445efbc02559c2a7c90f67bcb0154b04b03a1aa
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/25826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch sets the NPK device off for octopus.
BUG=b:76115112
TEST=Build for Octopus and check that the logs do not
report "PCI: 00:00.2 not found, disabling it".
Change-Id: I3ac01f90cf946b019a6604a38dd1d6782f8d5759
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25801
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When GPIO tables were created, there was no study on which pins had to be
programmed ASAP and which could be programmed later. Execute such study and
move all non-critical gpios from reset to late.
BUG=b:76097508
TEST=Build and boot grunt to OS, test OS for lost functionality (WIFI, video
playback, track pad, keyboard).
Change-Id: Icbc9370050d619800026035caaac3e89536a460a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With the increase of dimm->module_part_number size from 19 to 21 (commit
35b273eea3) "include/memory_info.h: Change part number field from 19 bytes
to 21", this code is now advancing outside DDR3 SPD designated space. The
correct size is already defined as LPDDR3_SPD_PART_LEN, use it. Also make
sure to 0 terminate the string.
BUG=b:77943312
TEST=Build cyan.
Change-Id: Iba0ef4149acfc09b7672fce079df06bf1a01dff6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change adds keyboard backlight feature for Nami platform
BUG=b:78360907
BRANCH=none
TEST=keyboard backlight works when EC reports correct info.
Change-Id: I3fceb83e155032b6e9f1763c4e2a29e7521269d2
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enables the i2c trackpad on atlas.
BUG=b:75454415
TEST=able to move pointer using trackpad
Change-Id: If4a82aa605ec68fd38e52c13406eaf803f9e86cc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These settings are identical to yorp settings except
overrides are not provided for sleep_gpio[] table which
is currently empty for yorp and cros_gpios[] table which
is not expected to change for bip.
BUG=b:77869623
BRANCH=none
TEST=Build coreboot for bip.
Change-Id: Icc205f576691427d78c9159dfdbced87e41a0517
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move inline function where they belong to. Fixes compilation
on non x86 platforms.
Change-Id: Ia05391c43b8d501bd68df5654bcfb587f8786f71
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25720
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO definition structure has evolved to a point where it's no longer
specific to stoneyridge, though probably still specific to AMD. Therefore,
rename the GPIO declaration structure removing stoneyridge from it.
BUG=b:72875858
TEST=Build kahlee, grunt, gardenia.
Change-Id: Ib034d3f7840c36ee8f5c5384241d7326d3fe5543
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25726
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change selects DRIVERS_I2C_HID which is required for adding SSDT
node for digitizer.
BUG=b:78099046
Change-Id: I526c0ac7b88dec7b2b22d022d911840555f15cde
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
With the exception of code that deals directly or indirectly with AGESA,
all other code should be independent of vendor code reference. Therefore,
remove vendor code reference from any GPIO code.
BUG=b:77999987
TEST=Build and boot grunt.
Change-Id: I9ba78767a269ad6b9b06fa11993d8a12350e4bad
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25695
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As part of preparing to make GPIO code independent of vendor code references,
convert GPIO table format using newly defined macros.
BUG=b:77999987
TEST=Build and boot kahlee.
Change-Id: I0af768bb4dbcbfef0d2d08ffe869c1dfb6827974
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change sets VmxEnable to 1 to match the kernel setting.
If this feature is enabled at the kernel level and not in FSP,
then there is an issue where FSP expects it to be disabled so
it forces a cold reboot on every warm reboot.
BUG=b:78129261
BRANCH=poppy
Change-Id: Idedbde1d8eb0c9e959733b7b50e5dec804d61cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25698
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC code should not have been removed from devicetree when moving
over from grunt. This was causing various bewildering issues that
would happen on the first boot but not on subsequent reboots.
BUG=b:73235377
TEST=Grunt powers off and stays powered off at dev screen.
Change-Id: I225138fede66c6e189e0e79d1261d0d579f7cbdc
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
The EC pin definitions are GPEs, not the GPIO numbers.
BUG=b:74022675
TEST=Power status updates immediately when power is inserted.
Change-Id: Icc8330a606f7a85e72b65094462a684927986829
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25689
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating some GPIOs based on changes in the latest schematics. Also
renaming signals to match that of latest schematics.
BUG=b:73749640
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Make sure different SKUs still boot.
Change-Id: I7d912f4bc6765f065c75c68a45bdf9ee844e0c1d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With one additional EC change, Yorp is able to flash the EC as part of
software sync and successfully boot. This change is only made for Yorp
as we want this disabled for Bip bringup.
BRANCH=none
BUG=b:77874283
TEST=Successful flash and boot on Yorp with this change
TEST=Checked GBB flags on Yorp and Bip images with gbb_utility
CQ-DEPEND=CL:1014397
Change-Id: I4969b254c6a58fba9dd8d2f31feb25b55c7a0c65
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25692
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Generalize cbfs_boot_load_struct() by passing in CBFS type
Change-Id: I6e5f845cb4ce5b00f01a39619919f85e39028f19
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The commit enables DPTF function. The DPTF parameters are provided by
thermal team.
BUG=b:72974136
BRANCH=poppy
TEST=emerge-nami coreboot then check the parameters in DPTF ui tool
Change-Id: I9b7ae34ee64f19ef783a8c1571831b2293105a18
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This will enable crossystem to access WP GPIO
BUG=b:78009842
TEST= wpsw_cur in crossystem reads the correct gpio
Change-Id: Iedd0057d6bdfd5a666ff282bc784f7b98e8c96e8
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/25673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add SPD file for sdp hynix_dimm_H5AN8G6NCJR-VKC (ram id: 15).
BUG=b:77893710
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I434d42ff12e6dae39e5676f36ba6cf00b3a48b06
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp micron_dimm_MT40A512M16LY-075E (ram id: 14).
BUG=b:77930401
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: Ia44e70948e57c2f19664d874ae005ac39d748f92
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The EC should wake the system from S3 when the AC connector is plugged.
BUG=b:77602394
TEST=verify resume on insert with Grunt
Change-Id: I4bcaef2fe75283aaa6260b5b9efd408ff4b05f4c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
bt-pad-enable property is used by kernel driver to set
BT I2S PAD on ACP_BT_UART_PAD_SEL mux, for those platforms which
use these pins for BT I2S. By default the pins are set for UART.
BUG=b:72360151
TEST=Tested playback and capture on audio device connected to BT I2S
Change-Id: Id76bfa1fa1dde904f02a03b0c15986ecb1bbcc97
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25653
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit aef0d6b0a7ec867ee29acf9e1c695be27626f239.
This commit can only pass far-end USB eye diagram but will fail on
near-end. Confirmed with Intel we should revert it.
Change-Id: I2eb1d5ddb05ca6bbf6512edf48e3e0d8396ce6a7
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/25651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Turn on keyboard backlight in romstage to indicate that the system is
booting.
BUG=b:77921345
TEST=Boot grunt, keyboard backlight comes on.
Change-Id: Ib215b19ebdee2f8c4f431af775905eca42436d1c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25636
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 70ba1b7e78930acca578114cdadcbcec367730e8.
This commit can only pass far-end USB eye diagram but will fail on near-end.
Confirmed with Intel we should revert it.
Change-Id: I6de44d5240393409d9ec5835a9de0c23453300f7
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25630
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI interrupt routing file routing.asl is not reflecting AGESA settings to
the NB Interrupt Routing Registers. The AGESA settings are:
Device self INTA INTB INTC INTD
GPP 0 23 0 1 2 3
GPP 1 24 8 9 10 11
GPP 2 25 16 17 18 19
GPP 3 26 24 25 26 27
GPP 4 23 3 0 1 2
HDA none 22 23 20 21
GBIF none 6 7 4 5
Fix the routing table, considering that NB IOAPIC starts at interrupt 24.
BUG=b:74104946
TEST=Build and boot to a modified grunt board to enable the emmc. Then used
"cat /proc/interrupts" to get active interrupts. Also checked IOAPIC
redirection registers, which are now being programmed.
Change-Id: I60847c46f3f938f9e97d7b323b27d20e36aa2d02
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reverts commit 06e3e1f055593bd2e2906f43040a703bc471cde4.
This commit can only pass far-end USB eye diagram but will fail on near-end.
Confirmed with Intel we should revert it.
Change-Id: Ie987061e27996b0acc8345bf9aadb42d2c940808
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25629
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables EC SMI when ESPI is enabled.
BUG=b:77857802
TEST= SMI is working in depthcharge.
Change-Id: I52726194b8346488e5ad781e78e33c5d286d132f
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25569
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the recovery cache to speed up recovery flows. Also
enable clearing of the normal mrc cache on recovery forced retrains.
BUG=b:77871444
TEST=went into recovery twice. 2nd time it boots faster.
Change-Id: Idfce42ac835637fa521545fadfedecd65df91d4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change selects DRIVERS_SPI_ACPI which is required to add SSDT
node for SPI TPM.
BUG=b:75306520
BRANCH=None
TEST=None
Change-Id: I0728062dae017522ba91a4b5cb16acf9f6bf4f28
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25611
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes: 2269a3c328 ("soc/amd/stoneyridge: Add functions for GPIO interrupts")
Change-Id: I5730259bc6819defc482d31644e1f476679257b2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25588
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt supports a keyboard backlight, so enable the ASL code.
BUG=b:77455525
Test=Boot Grunt, verify that the string 'KBLT' is in the DSDT.
Change-Id: Idf0f23581bcba0b035c126c68fb167274d7c698a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25470
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is for consistency with other platforms.
BUG=b:77494826
BRANCH=None
TEST=Sucessfully rebooted, saw updated name in SMBIOS
Change-Id: I83d9075931d51b3aef8076e4567a85a808ee5047
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25591
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As part of moving AGESA calls from bootblock to romstage, OemCustomize.c
of all boards using stoneyridge must be available at romstage.
BUG=b:74236170
TEST=Build grunt and kahlee, actual test will be performed at a later patch.
Change-Id: Ide9efdbff6a07c670034391c0d62e8b74fa5c02b
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25528
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes: ba49c09b2f ("mb/google/poppy: Add variant for Atlas")
Change-Id: I9c5c10abf8129ff61b97312a70ed4749606a3090
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25556
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Vayne.
We need to disable rear camera on all Vayne sku.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera shown on Vayne
Change-Id: I6e7c1e8791462f00ad8336372954ee0a9465d9b8
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch sets the wake for EC to proper gpios.
BUG=77605178
TEST=Test that lidopen wakes up the system from S3.
Change-Id: Icbf30007403191005396027e74b9b6fb7319e006
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25539
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the DPTF parameters for Octopus baseboard.
These parameters are copied from reef/coral as initial reference values.
BUG=None
BRANCH=None
TEST=Build coreboot for Octopus board.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I069bae8c9ef43ebd1ee20945ef34a7f51991f621
Reviewed-on: https://review.coreboot.org/25339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Interrupts from cr50 are edge-triggered, not level-triggered. This
change updates the GPIO configuration accordingly.
BUG=b:75306520
BRANCH=None
TEST=None
Change-Id: I0c5fb4495b404412a78965c2de7f00248d0c684b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables DPTF support for Octopus baseboard.
BUG=None
BRANCH=None
TEST=None
Change-Id: I88a94c73ef0c9da708c0440f7edadd85488edfdb
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/25342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp hynix_dimm_H5AN8G6NAFR-UHC (ram id: 6).
BUG=b:77290144
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I33503de21c9fc14537c00c092986fd4d2998dace
Signed-off-by: chriszhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
The WP signal to the AP isn't inverted as it is on other platforms, so
it was reporting incorrectly. Change the ACPI table to be active low,
and invert the signal when reporting it to everything else.
BUG=b:74946358
TEST=Boot grunt with battery inserted, WP signals both report 1. Remove
battery, WP_CUR reports 0, WP_BOOT still reports 1.
Change-Id: Ic1369dbda609e34b308af308880449643be6af39
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch sets PL1 value to ~6W. Here, 8W setting gives
a run-time 6W actual measured power.
Also, this patch sets PL2 value to 15W.
BUG=None
BRANCH=None
TEST=Build and read the MSR 0x610.
Change-Id: I2439a49b9917db0d9b05f333ce1c35003da493f6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/25341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch selects `HAVE_APCI_RESUME` to enable S3 resume. This
has a dependency on EC to store the hash.
BUG=b:72472969
TEST=suspend and resume from S3 should work.
Change-Id: I9de84dfd450936b3bc08e016bec6cf5ae88eab3d
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25390
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:73137125
TEST= tested trackpad on Octopus
Change-Id: Icc416e7be4e42bda188f74c69db150ba42562128
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/25415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This fixes wake from S0ix
Change-Id: I3b340deafccbf909ec1f4b11ba9a77c6b13a89fd
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/25467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Patch corrects SSP configuration to enable audio on GLK boards.
Octopus variant board uses max98357a speaker codec and 4CH DMIC,
Select the appropriate NHLT blob to be packaged in CBFS.
Change-Id: I101ed80f4421925120116b018424ef19d95a2a3a
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/25387
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.corp-partner.google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=None
BRANCH=None
TEST=On octopus, "aplay -l" shows the Audio codec.
Change-Id: I5d837d62f00d34edf28fd472ae0dbe7c0d94447a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a new variant of Poppy for the Atlas board.
BUG=b:75454415
TEST=tested on a P0 board. System boots and is mostly
functional, though some peripherals are not ready so there
are no touchpad/touchscreen devices configured yet.
Change-Id: I5a0bccd1bda0134aa51885ac2c6e7bb5b45de924
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change updates devicetree and GPIO configurations to match the
schematics:
1. pcie_rp...[2] is the one being used for wifi, thus, clk_req and
deemphasis_enable for [2] need to be set instead of [0].
2. WLAN power enable, wifi disable and PERST# GPIOs need to be
configured correctly.
BUG=b:76180142
TEST=Verified that wlan0 scan works.
Change-Id: Ic51a94902e2cac3491081ade32079e5b88719f45
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This moves the sandybridge both smm setup and smihandler code to a
common place.
Tested on Thinkpad X220, still boots, resume to and from S3 is fine
so smihandler is still working fine.
Change-Id: I28e2e6ad1e95a9e14462a456726a144ccdc63ec9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch disables debug consent in the devicetree. When debug
consent is set to DBC by default, it prevents some clocks from turning
off during S0ix. This blocks S0ix entry.
This patch also enables S0ix from the devicetree.
BUG=b:76163091
TEST=enter S0ix and check if slp_s0 is asserted
Change-Id: I05001a41b13e7784c34fa8f1f773fb94bbdcd01f
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/25312
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current emmc tuning parameters for octopus were copied over from other
boards and result in failure to boot from emmc. This change gets rid
of the emmc tuning parameters in devicetree. Once emmc tuning tests
are run for octopus, these parameters can be added back.
BUG=b:75986903
BRANCH=None
TEST=Verified that octopus boots from eMMC without any errors in
depthcharge.
Change-Id: I7ac44a54afd1ecfe355a9654ac8e92133b67637f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change remove work-around code for the power issue of MIPI and
USB cameras on previous board revision. With the work-around code,
PMOF ACPI method cannot turn off MIPI camera. So we need to remove
it.
BUG=b:74214248
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/25337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=build
Change-Id: I32d185741ce20a3a82e6895de3026ade52d0bcc8
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/25200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch sets the PNP config value to PNP_PERF_POWER.
The config values for soc can be found in chip.h
TEST = Build for octopus.
Change-Id: I2239aa70cb708e6e1c06339ca9d517e7eaa198ed
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/25310
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a new Kconfig option for mainboard octopus "HAS_TPM"
that auto-selects all TPM related options only if VBOOT_MOCK_SECDATA
is not selected.
BUG=b:76203913
TEST=Compiles fine with mocktpm.
Change-Id: Ib28fc47a70be58cd9a9ec65ce3b1cda68d558437
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25340
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Always report that EC is in RO mode. This is a temporary workaround
for a hardware issue that is causing EC to appear to be in RW mode
when it is not. This change will be reverted once transition is made
to newer hardware.
BUG=b:74215817
BRANCH=master
TEST=Verify meowth can boot to recovery's insert screen.
Change-Id: Ib3705bba0bb1f351da79e599566fbffab94428f3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:72120814
BRANCH=master
TEST=none
Change-Id: I64ab38dda78345c1f3d7d3f2bf3cb04c19290ceb
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:73292699
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: Ic73ad38ad9a12bec614e530f7f35619246b9f57f
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/25288
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I2C bus 2 goes to the custom add-in card slot and it was disalbed cuase
it was idle.
Google CFM add-in card is going to use this I2C bus so it needs to be
re-enabled.
BUG=b:73006317
TEST=Tested with add-in card on fizz hardware and verified I2C bus 2 is
working properly.
Change-Id: I2c9b5a9323fd51872e340c35005c4a3432716808
Signed-off-by: Zhongze Hu <frankhu@chromium.org>
Reviewed-on: https://review.coreboot.org/25258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update the size in WP_RO segment of the flash to accommodate builds using
debug FSP.
Change-Id: I0a0d1d0121b503ff390adf3ce25973d72e59fdeb
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/25253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This creates a bip variant for octopus. Nothing is set in the variant
files here-- everything is picked up from baseboard.
BUG=b:75976864
TEST=None
Change-Id: I7a8ac3d8bb71416f05ef1a605684d92d5902abda
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25285
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:73078053
TEST=build & boot Grunt
Change-Id: I2d4ba197b19c4948b867a61575e858b2a826a286
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Tools/scripts, like mosys/arc-setup, use int (4 bytes) to
read the sku id. In order to support "-1", we need to use
uint32_t (4 bytes) instead of using uint16_t (2 bytes) data type.
Otherwise, tools/scripts will read 65535 instead of -1.
Another reason to change this is that sku_id can be
supported by ec up to 4 bytes.
BUG=b:73792190
TEST=mosys output "Platform not supported" for -1 sku id
arc-setup read -1 sku id
Change-Id: Ib3baa8419f138abeb412ac09c2e7dc608e3b758b
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:73133848
BRANCH=None
TEST=Build coreboot for Octopus board. Tested the GSPI interface
with a SPI EEPROM and got correct response to a RDID command
Change-Id: Ia10ab9da0055b54a96134a6e4c51b2a229a6fecf
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/24907
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures GPP_E22 to GPO_HIGH to enable CABC feature
on nautilus board.
BUG=b:68789889
BRANCH=poppy
TEST=emerge-nautilus coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ifed0d37bf8147aa1b580f594f36f186051c2eb52
Reviewed-on: https://review.coreboot.org/25120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Audio machine driver will enable/disable clock by making it as
a CCF clock in kernel.
BUG=b:74570989
TEST=cherry-picked https://patchwork.kernel.org/patch/10291875/
on 4.14 kernel
aplay -vv <file>
check register to see clock enabled
kill aplay
check register to see clock disabled
Change-Id: Ia553e55ffb358415067000d2d2d2744322d1c4db
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/25263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up the EC communication a little earlier so we can read the board
ID before programming GPIOS.
BUG=b:73078053
TEST=Build & Boot grunt, board_id() now gets ID correctly
Change-Id: Icf3f598824cfed69fa03ba2bb86503bb3c3699a5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/25286
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to the schematic, Octopus boards have WLAN_PE_RST connected to
GPIO_164. This change configures that properly in devicetree.
BUG=None
TEST=None
Change-Id: I2ba4839e036f02c5e0316d08599894879133894a
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25248
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO pad configurations for GPIO68-71 are incorrectly configured as
outputs. This change corrects them to be inputs.
BUG=b:74932341
TEST=None
Change-Id: I319f8a64d83c29ed150316c15a8d429cc7c024f3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25217
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:74177699
BRANCH=poppy
TEST=Verify audio recorder function by different SKU ID
Change-Id: Ic6570703f6ab4a1b03cbba8370fc0f597ab6bcf2
Signed-off-by: amanda_hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The GPIO for EEPROM write-protect should be configured early, before
romstage. This change configures that pad earlier. This pad is the same
on the existing Octopus schematics.
BUG=None
TEST=None
Change-Id: Idf296ba6aad75b890afabd6f7c7c51fbaf911214
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/25250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
