| Age | Commit message (Collapse) | Author |
|---|
|
Configures ISH related GPIO's based on FW_CONFIG obtained from CBI.
BUG=b:280329972,b:283023296
TEST= Set bit 21 of FW_CONFIG with CBI
Boot rex board
Check that ISH is enabled, loaded, and functional
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I3f0f9a7c8318fa9ae59b6f613eafdacbfa07c749
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Rename shared SRAM aliases for IOE and PMC to make them more readable.
pci device 13.3 is IOE shared sram, renamed to ioe_shared_sram.
pci device 14.2 is PMC shared sram, renamed to pmc_shared_sram.
Rename them in SOC code as well as mainboard to make sure the patch
builds for the relevant boards.
BUG=b:262501347
TEST=Able to build.
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I02a8cacc075f396549703d7a008382e76258f865
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75999
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CNVi PCI device is required for the system to boot properly.
By ensuring that this device is enabled, we can prevent the below
error message from appearing and ensure that the system boots successfully.
BUG=b:274421383
TEST=Able to build and boot google/ovis without any error.
w/o this patch:
[ERROR] CNVi WiFi is enabled without CNVi being enabled
[ERROR] CNVi BT is enabled without CNVi being enabled
Change-Id: I4dbae14f0cfccf96a33437a0e2fdefb508209354
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Reducing the polling time from 16ms to 2ms. Experimentally we
have determined that the link state normally takes approximately
3.5ms to update and therefore we were waiting longer than necessary.
TEST=build and confirm we are not waiting the extended period.
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I8fabb5ac46cae5c92d5b6f1dc0641a4d121c61dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76052
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Reduce the delay between PEXVDD and NVVDD from 3ms to 2ms
during power down sequences. The hardware discharge is
aggressive enough that we can safely optimize this.
BUG=b:288267305
TEST=build and measured delay is acceptable
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I7c65301414044487e50bbbca618c4e602e571cfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76051
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
When powering rails down, there is no value in waiting for the PG
signal to de-assert. Instead, shut the rails off as quickly as possible
while maintaining a controlled ordering.
BUG=b:288266850
TEST=build and measured delays are gone
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: If31691a7d62b72661fcbacb34e90f3a6adec8134
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76050
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pre-boot display is not POR for google/rex hence disable the config
ENABLE_TCSS_DISPLAY_DETECTION.
BUG=b:247670186
TEST=Build and boot to google/rex and make sure that display over TCSS
works in the OS
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ib55e251a4620c7a375ee2f27763154c39207236e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
the board won’t have a SD card reader, so disable it.
BUG=b:285477026
TEST=USE="project_joxer emerge-nissa coreboot"
Change-Id: I6a55058b453771d264700a1364ef538f831148e4
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
For Phoenix the lane numbers in the DXIO descriptor match the ones in
the schematic, so remove the corresponding text and the table from the
comment on the fsp_dxio_descriptor struct. Since there's no logical to
physical lane number remapping needed for the lanes in the Phoenix DXIO
descriptors, drop the 'logical' from the start_logical_lane and
end_logical_lane fields in the DXIO descriptor and rename those to
start_lane and end_lane.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94664fd9d3807370b73f9fae8645d444e5faf7b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Since GPP_C03/GPP_04 are floating in HW design, we set HBR smbus pin
as NC, in case it prevents ese and cse from entering suspend.
BUG=b:283053968
TEST=Verified on screebo non-TBT SKU, suspend and resume works.
Change-Id: I401db32f0286de61ce3ab6c61de9528ec76cb51d
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75643
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
USB type-A port with same PLD.token information as USB type-C port,
causes conflict while generating ACPI code for the EC CONN device.
Use a different PLD.token number for type-A port to fix the issue.
BUG=b:286328285
TEST=check ACPI can have right USB port in EC CON.
before patch:
Package (0x02)
{
"usb2-port",
\_SB.PCI0.XHCI.RHUB.HS01
},
Package (0x02)
{
"usb3-port",
\_SB.PCI0.TXHC.RHUB.SS01
},
after patch:
Package (0x02)
{
"usb2-port",
\_SB.PCI0.XHCI.RHUB.HS01
},
Package (0x02)
{
"usb3-port",
\_SB.PCI0.TXHC.RHUB.SS03
},
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: If3e76c11dd6808eee4c9c2f3f71604a60379b5a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Ovis uses MTL-H.
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
TEST=cros build-packages --board ovis chromeos-bootimage
Change-Id: I284c72b902490187d0b15e4fc81650af1cfa16d7
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75887
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch renames config `SOC_INTEL_METEORLAKE_U_P` to
`SOC_INTEL_METEORLAKE_U_H` as per Intel Meteor Lake Processor EDS
version 1.3.1 (doc number: 640228).
With new branding, the MTL-U/H-Processor Line offered in a 1-chip platform that includes the Compute, SOC, GT, and IOE tile on the
same package.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I032be650bbfef0bf0ef86bb37417b1d854303501
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75931
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
get_usb_port_references refer the PLD group. If the port assign cross
ports like mux[0] use USB3 and mux[1] use USB1, then we need set USB3
to group 1. Update the PLD panel to back as well.
BUG=b:286328285
TEST=check ACPI can have right USB port in EC CON.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I97517ecd4f8615af749fb6d007ded8e171796f7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75912
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Using the boolean type and the true/false macros give the reader a
better understanding about the option. Thus, use the bool type for the
attribute and use the macros for assignments.
Skylake mainboards which use that option were changed by the following
command ran from the root directory.
socs="SOC_INTEL_(SKYLAKE|KABYLAKE|SKYLAKE_LGA1151_V2)" && \
option="s0ix_enable" && \
grep -Er "${socs}" src/mainboard | \
cut -d ':' -f 1 | \
awk -F '[/]' '{print $1"/"$2"/"$3"/"$4}' | \
xargs grep -r "${option}" | \
cut -d ':' -f 1 | \
xargs sed -i'' -e "s/${option}\".*\=.*\"1\"/${option}\" \= true/g"
Change-Id: I372dfb65e6bbfc79c3f036ce34bc399875d5ff16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75871
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Configure I2C0/1/3/4 timing in devicetree to ensure I2C devices
meet timing requirement. Note that I2C5 timing will be updated
separately when the tuning done
BUG=b:280559903
TEST=Build and check I2C devices timing meet spec.
| | I2C0-Codec | I2C0-WFC | I2C1 | I2C3 | I2C4 |
|-------------|------------|----------|--------|-------|---------|
| FSMB(KHz) | 347 | 343.2 | 389.3 | 393.7 | 381.9 |
| TLOW(us) | 2.1 | 2.093 | 1.895 | 1.902 | 1.953 |
| THIGH(us) | 0.647 | 0.628 | 0.602 | 0.62 | 0.612 |
| THD:STA(us) | 0.633 | 0.64 | 0.601 | 0.6 | 0.601 |
| TSU:STA(us) | 0.617 | 0.621 | 0.619 | 0.659 | 0.61 |
| TSU:STO(us) | 0.656 | 0.647 | 0.667 | 0.727 | 0.634 |
| TBUF(us) | 86.15 | >14.088 | >9.833 | >8 | >10.366 |
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Change-Id: I5421e4fe68e856bbe9f19544954a94670c895a47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75150
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Remove rp2 and add rp1/rp3 for screebo
BUG=b:286187816
BRANCH=none
TEST=emerge-rex coreboot and verify TBT works.
Change-Id: I1013d26c705f2a3f9378d944bd863d94f319d36c
Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75832
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update overridetree to support ELAN and G2_G7500 touchscreen.
BUG=b:285477026
TEST=emerge-nissa coreboot and check touchscreen function
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I236a2815f956929c6cd84c981cb15e9ab0f657b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75762
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'ModPhyIfValue'.
Change-Id: I4cdf68e65cea4ab316af969cd6a8d096b456518d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75855
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'DisableComplianceMode'.
Change-Id: I9d5605134a753f161a66857c7f78844ae7490cd6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'PmicPmcIpcCtrl'.
Change-Id: I3632d1e83108221d3487b4f175133ad347238bc5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75853
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DDI on ports 1 to 4 for Type-C DisplayPort.
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: I40f967b12b11c10a1a9329bfb42ebec5a8d7738f
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75579
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configures the SoC to flip the orientation of the AUX pins to
follow the orientation of the cable when using the anx7452 retimer. This
is necessary when there is no external retimer/mux or the retimer/mux
does not implement the flip. The anx7452 retimer does not appear to
support this feature, so let the SoC do the flip.
BUG=b:267589042,b:281006910
TEST=verified DP-ALT mode works on rex using both cable orientations
Change-Id: Ibb9f442d2afd81fb5dde4bca97c15457837f9f4a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75827
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
USB3 is used for both typeA and WWAN based on different DB.
BUG=b:287159026
TEST=change FW config and check typeA and WWAN can work.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I5ad3973a9519350794a661ad00f71c0eb34edfba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75819
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the support RAM parts for gothrax.
Here is the ram part number list:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H58G56AK6BX069 1 (0001)
K3LKBKB0BM-MGCP 2 (0010)
BUG=b:284388714
BRANCH=None
TEST=emerge-nissa coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ib16846f7b2061ee254db674ac7bac66c9b9f4e70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75834
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
TCSS and TBT use the same lane on schematic. Update the port start
from 0 to match the Intel schematic. You can better follow the it
without convert the port number.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ic6631dcbbd9f6c79c756b015425e2da778eb395e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
- Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned, and devicetree does not currently support this. (it
disables all probed devices when fw_config is unprovisioned.).
- Removed `bootblock-y += variant.c` from Makefile.inc based on
CL:3841120.(The infrastructure for selecting an appropriate firmware
image to use the right descriptor is now ready so runtime descriptor
updates are no longer necessary.).
BUG=b:285477026
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I6920d88dfec86676ff6733146f748e06d4085c49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75743
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
There are two baseboards within the set of mainboards built
here, with baseboard name appended in the filenames.
Take the style and variable BASEBOARD_DIR from google/brya,
then move and rename the supporting files under separate
directories.
Change-Id: I2046b6f82519540b8596ce925203bd60d1870c1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74471
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add additional ram parts and generate strapping ids.
BUG=b:285216975
TEST=Build myst image
Change-Id: I2b3b8c9ffcf81bbd2d6ecfad1b612fbf793857c8
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75821
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Add support for Micron MT53E2G32D4NQ-046 WT:C LP4x DRAM.
BUG=b:216393391
TEST=build pass
Change-Id: I3797de01629fdb5ace4c610943d88db525da112b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75826
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
This patch enables BT offload feature on Rex over SSP1.
BT mode is selected via FW_CONFIG and corresponding VGPIOs are
programmed.
BUG=b:275538390
TEST=Verified audio playback using BT speaker/headset in I2S mode on google/rex.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I46e9702add37464122ffc78826ebf8a6c5b5b07c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72881
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pujjo does not support GPIO based D-SAR,
so set GPP_D15 and GPP_H23 to NC.
BUG=b:275264095
TEST=boot on pujjo and no impact WWAN dynamic SAR function
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I4fe40b32a572a8d914e01e5cd7927766ccf17c02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75403
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Lay the groundwork to prepare for enabling PSP verstage. This change
adds PSP verstage callback to enable eSPI, TPM etc.
BUG=b:284984667
TEST=Build Myst BIOS image with PSP verstage enabled.
Change-Id: Ifc800e8bb27cc4c3fbccc2ab9f51138a7c4b03a6
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75585
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
This patch renames `SOC_INTEL_STORE_CSE_FPT_PARTITION_VERSION` config
to `SOC_INTEL_STORE_ISH_FW_VERSION` to ensure the usage of this config
is clear.
Any platform would like to fetch the currently running ISH firmware
version should select this configuration.
TEST=Able to build and boot google/marasov.
Change-Id: Ie503d6a5bf5bd0d3d561355b592e75b22c910bf5
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75767
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Boxy audio codec chip uses ALC5682I-VD, not ALC5682I-VS.
It needs to modify codec HID to "10EC5682" in coreboot to fix audio no
output sound issue.
BUG=b:286970886
BRANCH=dedede
TEST=confirm audio soundcard can be list by command "aplay -l"
Change-Id: Icd69a9d757ba817b586a703a17375682db684224
Signed-off-by: Kevin Yang <kevin3.yang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
This patch enables adding variant specific ASL code
TEST=Kernel driver is able to communicate with device
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I231482d56dd4afa150766c07cfde105158e5e124
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74886
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add driver to support ELAN touchscreen using SPI for rex
* See "HID Over SPI Protocol Specification" section 5.2 - ACPI enum
* https://www.microsoft.com/en-us/download/details.aspx?id=103325
BUG=b:278783755
TEST=Kernel driver is able to communicate with device. Also tested
S0ix, ran 'suspend_stress_test -c 1' - no issues in suspend/resume.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Id51d385ce350cef23da4184b044c74569f4dd3f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74885
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
One specific Hynix LPDDR5x DRAM part requires an ABL workaround to
eliminate DRAM-related failures during a FAFT test, but due to the
use of generic/common SPDs, there is no way for the ABL to determine
the DRAM part # itself.
Consequently, we will have coreboot check the DRAM part #, and set/clear
a CMOS bit as appropriate, which the ABL will check in order to apply
(or not apply) the workaround.
The ABL already uses byte 0xD of the extended CMOS ports 72/73 for
memory context related toggles, so we will use a spare bit there.
BUG=b:270499009, b:281614369, b:286338775
BRANCH=skyrim
TEST=run FAFT bios tests on frostflow, markarth, and whiterun without
any failures.
Change-Id: Ibb6e145f6cdba7270e0a322ef414bf1cb09c5eaa
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75698
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
On nissa, the ISH is running closed source firmware, so the ChromeOS
security requirements specify it must be behind an IOMMU. Add
DmaProperty to the ISH _DSD on joxer.
BUG=b:285477026
TEST=Kernel marks ISH (PCI device 12.0) as untrusted, and changes the
IOMMU group type to "DMA". Also, device still goes to S0i3.
Before:
$ cat /sys/devices/pci0000\:00/0000\:00\:12.0/untrusted
0
$ ls /sys/kernel/iommu_groups/5/devices
0000:00:12.0
0000:00:12.7
$ cat /sys/kernel/iommu_groups/5/type
DMA-FQ
After:
$ cat /sys/devices/pci0000\:00/0000\:00\:12.0/untrusted
1
$ ls /sys/kernel/iommu_groups/5/devices
0000:00:12.0
0000:00:12.7
$ cat /sys/kernel/iommu_groups/5/type
DMA
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I69b00f0281f4493db157783840d9cdcbb138017f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75758
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add default Intel DPTF.
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Ib023f6d6d184f6935a6a454250755502a46b707f
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75580
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
+-------------+----------------+------------+---------------------------------+
| PCH USB 2.0 | Connector Type | OC Mapping | Remarks |
+-------------+----------------+------------+---------------------------------+
| 1 | Type-C | OC_0 | Type C port - TCP1 |
| 2 | Type-C | OC_0 | Type C port - TCP0 |
| 3 | Type-C | OC_0 | Type C port - TCP2 |
| 4 | Type-A | OC_3 | USB3.2 Gen2x1 Type-A Port – TAP0|
| 7 | Type-A | OC_3 | TAP1 |
| 8 | Type-A | OC_3 | TAP2 |
| 9 | Type-A | OC_3 | TAP3 |
+-------------+----------------+------------+---------------------------------+
+---------------------+-------------------+------------+---------+
| PCH USB 3.1 Gen 2x1 | Connector Details | OC Mapping | Remarks |
+---------------------+-------------------+------------+---------+
| 1 | Type-A | OC_3 | TAP0 |
| 2 | Type-A | OC_3 | TAP1 |
+---------------------+-------------------+------------+---------+
+------+-------------------+------------+-----------------------------+
| TCPx | Connector Details | OC Mapping | Remarks |
+------+-------------------+------------+-----------------------------+
| 1 | Type C port 0 | OC_0 | To onboard Type-C connector |
| 2 | Type C port 1 | OC_0 | To onboard Type-C connector |
| 3 | Type C port 2 | OC_0 | To onboard Type-C connector |
+------+-------------------+------------+-----------------------------+
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Icc81f12ec6cc4af37bcc1fcf3164cbfa5612a443
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
When fw_config is unprovisioned, devicetree will disable all probed
devices. However, boot-critical devices such as storage devices need to
be enabled.
As a temporary workaround while adding devicetree support for this,
remove the fw_config probe for storage devices so that all storage
devices are always enabled. On eMMC SKUs, UFS and ISH will be disabled
by the PCI scan anyway. On UFS SKUs, eMMC is not disabled by the PCI
scan, but keeping it enabled should have no functional impact, only a
possible power impact.
BUG=b:285477026
TEST=On joxer eMMC and UFS SKUs, boot to OS and
`suspend_stress_test -c 10`
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I834bd81ce636a6f32d50434cbf07b1d572620492
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75757
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIE_RST_L is attached to a pull down, change the init to NC.
BUG=None
TEST=Boot to OS
Change-Id: I3f7a548a33eb18327139f033d7c0d6a1843f1639
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75700
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update PCIe GPIOs during rom stage to properly initialize the
PCIe devices and allow the NVMe/eMMC to be properly detected.
BUG=b:284213391
TEST=Boot to OS
Change-Id: I24ad6c1addedb414afade2512b6628022d000a47
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Move the WP signal to GPP_E12 from the current GPP_E15 to
match the design.
BUG=b:285084125
TEST=WP signal reports as we expect
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I8772173fcdcabf78b0c7d605cd495ebe04b63242
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add support for Micron MT53E2G32D4NQ-046 WT:C LP4x DRAM.
BUG=b:216393391
TEST=build pass
Change-Id: I8c66a18fd94d9a013710fbc6dc7f1533d808392e
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable ILI2901 and eKTH7B18 touchscreen for Google Screebo.
BUG=b:278167967
BRANCH=none
TEST=Build and boot to Google Screebo. Verify touchscreen works.
Change-Id: I57d55c5f2621d6fafd53b19d12ecad20271cdbb1
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
|
|
Currently if a rails PG fails to assert, the power on sequence
continue after the 20ms timeout. Instead, we should abort
and enter a power down.
BUG=b:285980464
TEST=sequence now aborts and powers down on failure
Change-Id: Id0865e6bdb5db1815ad5509306637308e98c15d7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: I6f3fa6543a4cec8c2562196105f17fbc7831bab7
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch configures external V1p05/Vnn/VnnSx rails for Joxer
to achieve the better power savings.
* Enable the external V1p05, Vnn, VnnSx rails in S0i1, S0i2, S0i3, S3,
S4, S5 , S0 states.
* Set the supported voltage states.
* Set the voltage for v1p05 and vnn.
* Set the ICC max for v1p05 and vnn.
Kit: 646929 - ADL N Platform Design Guide
BUG=b:285477026
TEST=Verified all the UPD values are updated with these configs.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I78d2a885d577f6c1a89ab74c0da7b6544322c0d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Baieswara Reddy Sagili <baieswara.reddy.sagili@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Properly shutdown NV12 rail in the off sequence (current
implementation leaves it asserted).
BUG=b:286287940
TEST=NV12 now shuts down on GCOFF entry
Change-Id: I7d338fc4a96f119617aff558413a5a9ac44c27d7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75533
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add pen detect support on the SOC pen detect GPIO.
BUG=b:286296762
TEST=Verify pen detect works on Myst
Change-Id: I922d643a83c5cd8ea0ab9fe6733f7aa05d935802
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Follow spec[1] to modify WWAN power sequence. The WWAN power sequence
of warm reset is fail. The correct sequence is WWAN_EN should keep high when doing warm reset. Set GPP_D6 to PWROK which is not to do PAD
reset when warm reset.
[1]:
[JDB10] FC ADL-N_WWAN sequence_FM101-GL SDX12 Power Timing
Review_V1.6_20230602.xlsx
BUG=b:285065375
BRANCH=firmware-nissa-15217.B
TEST=1. emerge-nissa coreboot chromeos-bootimage
2. power sequence meets spec.
Change-Id: If59630dbd10e971c91e01f33a657c01d857bc0b9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75690
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable wifi sar function for yavilla/yavilly/yavijo.
Use the fw_config to separate SAR setting for different wifi card.
BUG=b:286141046
BRANCH=firmware-nissa-15217.B
TEST=build, enabled iwlwifi debug, and check dmesg
Change-Id: I1bd111a734a250df49535a07ef056d5b68fccb33
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add new memory parts
DRAM Part Name ID to assign
Hynix H58G66AK6BX070 3 (0011)
Hynix H9JCNNNFA5MLYR-N6E 4 (0100)
Micron MT62F2G32D8DR-031 WT:B 4 (0100)
BUG=b:279325772
BRANCH=firmware-brya-14505.B
TEST=run part_id_gen to generate SPD id
Change-Id: I2e6a916de08e7c05e95909d2b69bc839d13192d9
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74713
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts.
The memory parts being added are:
1. K4U6E3S4AB-MGCL
2. K4UBE3D4AB-MGCL
BUG=b:285504022
BRANCH=dedede
TEST=build
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I87a4dcdb6196c3ca7bed4b5c1bc654297339c16d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75605
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of adding the new PCI IDs of the XHCI controllers in every new
chip generation to the pci_xhci driver, bind the driver to the internal
PCI devices of the XHCI controllers via the device ops statement in the
chipset devicetree. The PCI device function of the XHCI2 controller in
Mendocino can be either a dummy device or the XHCI controller, so the
device ops are attached to that device in the mainboard devicetree
instead. The Glinda code is right now just a copy of the Mendocino code,
so it'll change in the future, but for consistency the equivalent
changes to those in Mendocino are applied there too.
Since the device ops are now attached to the devices via the static
devicetree entry, also remove both the xhci_pci_driver struct and the
amd_pci_device_ids array from drivers/usb/pci_xhci/pci_xhci.c.
TEST=SSDT entries for the XHCI controllers are still generated on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c455002c6d2aac576fe24eee0c31744b4507bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Initialize the SPI Flash in bootblock to ensure that
CONFIG_SPI_FLASH_EXIT_4_BYTE_ADDR_MODE will exit 4-byte addressing mode.
BUG=b:285110121
TEST=boot myst and verify flash operations work correctly
Change-Id: Ia88d2b46884b096b4c558bc86513159ec6d35eb5
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75588
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for Micron MT53E2G32D4NQ-046 WT:C LP4x DRAM.
BUG=b:216393391
TEST=build pass
Change-Id: I0abf1f1105f9a6f16af23b0ed3eb4faeb669eee6
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75716
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Include the GPU ACPI methods for all of Hades baseboard.
BUG=b:285981616
TEST=built for Hades and verify shutdown works
Change-Id: Iec3c4b59a9e7a9d4a902db51d40b60e114521774
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
HW has invert the signal, set it to active high.
BUG=b:285964562
TEST=check crossystem wpsw_cur change as expected.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I54c578e5df5f1b24743cc9506e1e31b0b18bfb25
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75628
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add usb wwan device tree entry. Also set wwan_rst to high due to
HW design active high.
BUG=b:285792436
TEST=check FM101 is detected by Linux kernel.
Bus 002 Device 002: ID 2cb7:01a2 Fibocom Wireless Inc.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0aa60cb284d4b7f99e16643a92ee58467a355026
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75660
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add fingerprint into device tree. Also set RST to low per HW
requirement.
BUG=b:285799911
TEST=check ectool --name=cros_fp version.
RO version: bloonchipper_v2.0.5938-197506c1
RO cros fwid: CROS_FWID_MISSING
RW version: bloonchipper_v2.0.14348-e5fb0b9
RW cros fwid: bloonchipper_14931.0.0
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I09819037b80e55edeb56faef9e27fe0753748efc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75629
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new GFX devices for DDI and TCP with custom _PLD to describe the
corresponding ports.
BUG=b:277629750
TEST=emerge-brya coreboot
BRANCH=firmware-brya-14505.B
Change-Id: Ia083617c58d6b7ebc108e07e29a1c8061580eae5
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: I3795313e784595ac02ee2a38f466bcb9e613a6a4
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75576
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jan Dabros <dabros@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I1644b1d8f49accbb2ea68e236534df80a5151360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75503
Reviewed-by: Jan Dabros <dabros@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Based on Platform Mapping Document for Ovis (go/ovis_mapping_doc)
state for June 6, 2023 (Rev 0.3)
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Iae3ca243a245928e8ec3d48877cf578843922fc7
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75502
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
joxer removed SD card from all SKUs, thus disable pcie_rp7.
BUG=b:285477026
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I3486d665ddb1de521ab4e656addb2209055174c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75658
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Board IDs are now filled in as part of the signing process, so we don't
need to set them in coreboot.
BUG=b:240620735
TEST=Build and check VBOOT_GSC_BOARD_ID is set to ZZCR.
Change-Id: I7dda8ad59046a1dd9a28595e037eda86e91c98df
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75641
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new GFX devices for DDI and TCP with custom _PLD to describe the
corresponding ports.
BUG=b:277629750
TEST=emerge-rex coreboot
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: I193b95e8bd8ae538c4f25fbe772b174ef455d744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
All the DRAM module for Juniper/Willow can reuse the RAM ID in
offset 0x30 table, so change Juniper/Willow RAM table offset to 0x30
for introducing more DRAM modules.
BUG=b:284423187
BRANCH=kukui
TEST=emerge-jacuzzi coreboot
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I92740275dcc27061a94b7db7ce095655c0bd7cf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Uldren does not have PCIE device and should disable PCIE RP7 and
GPP_D7 for preventing PCIe controller not power gate in S0ix.
BUG=b:283735051
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
1. PCIE RP7: cbmem -c | grep 'PCI: 00:1c.6'
[SPEW ] PCI: 00:1c.6: enabled 0
[SPEW ] PCI: 00:1c.6: enabled 0
2. GPP_D7: iotools mmio_read32 0xfd6d0ab0
0x44000300
Change-Id: Ia8a2c0f5530c7a056e8d706c651cac1d49b2091c
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75644
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a -b ovis
Change-Id: Ic555fac846ebf1e9dad81b5847334c03d6804b5b
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
BUG=b:274421383
TEST=util/abuild/abuild -p none -t google/rex -x -a ; Make sure
GOOGLE_OVIS built successfully
Change-Id: I5c8f290cfdcb4d47c0e5e9d72c1e34073b957681
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75385
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The K&D-ILI9882T panel and STA-ILI9882T share all DCS commands and EDID
information except for the manufacturer_name which has no effect to the
function of panel. Let's reuse the STA_ILI9882T struct in this case.
BUG=None
TEST=emerge-staryu coreboot chromeos-bootimage and boot the panel
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I510462a49d273f3d25158b25906d4c514f855cdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Based on the power sequence of the panel [1], the power on T2 sequence
VSP to VSN should be larger than 1ms, and the power off T2 sequence VSP
to VSN should be larger than 0ms. We modify the power sequence to meet
the datasheet requirement.
[1] B5 TV110C9M-LL0 Product Specification Rev.P0
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I4ccb5be04062a0516f84a054ff3f40afbf5279be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Touchscreen may either use I2C1 or SPI0.
FW_CONFIG.TOUCHSCREEN is set to determine which is used.
This CL adds a probe to enable I2C1.
BUG=b:278783755
TEST=Tested on rex, confimed i2c1 is disabled when
TOUCHSCREEN != TOUCHSCREEN_I2C
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I0bee176298fddd2aee35cf084db037a3ce7672f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Follow 57263_FP8_MBDG_rev_0_92 Table.57 to update the alias. We
can match the schematic for now.
BUG=b:285793461
TEST=USB still works.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Id1058279fe5b0e3131608a0b9bbd708dbbde7e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Makefile.inc to include four LPDDR5x SPDs for the following
parts for Joxer:
DRAM Part Name ID to assign
K3KL6L60GM-MGCT 3 (0011)
H58G56BK7BX068 4 (0100)
MT62F1G32D2DS-026 WT:B 4 (0100)
K3KL8L80CM-MGCT 4 (0100)
BUG=b:236576115
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ibdc89c882581cfe4e5978faf4c6f70d653e0813d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75610
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
BUG=b:278783755
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I2a6de778c7ab30a9946e100cb70c092ba98496e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74944
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: I5c0395d33ee47ab1c7d45f33d6afb063b8263836
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75572
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: I51ff0991565d60807c100b33fb66ab10cc48b8e1
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Ensure USB-C ports' _PLD group numbers appear in order.
get_usb_port_references in src/ec/google/chromeec/ec_acpi.c uses group
token to match with the Type-C port number.
BUG=b:216490477
TEST=build coreboot and system boot into OS.
BRANCH=firmware-brya-14505.B
Change-Id: Ib564ffe272e73f46ec6608420dc431c8b017fb65
Signed-off-by: Won Chung <wonchung@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Select SOC_INTEL_RAPTORLAKE for kuldax so that it will use the RPL
FSP headers for kuldax.
BUG=b:285406822
BRANCH=firmware-brya-14505.B
TEST="FW_NAME=kuldax emerge-brask
coreboot-private-files-baseboard-brya coreboot chromeos-bootimage"
Cq-Depend: chromium:4583807, chrome-internal:6003096
Change-Id: Icbf8b26bc2bfee2559cce236bde80a99f8bff859
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75599
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Fast VMode nmakes the SoC throttle when the current exceeds the I_TRIP
threshold.
BUG=b:285406822
BRANCH=firmware-brya-14505.B
TEST=Verify that the feature is enabled by reading from fsp log
Change-Id: I9ae58d704cba8124c6cb9865431aff84c9d154f7
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75600
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add the phoenix usb config struct for Myst since the FSP has been
updated to accept the config from coreboot and the default values
do not work.
BUG=None
TEST=Boot to OS on Myst, verify devices are seen with lsusb
Change-Id: I329aba80f3003a3a5f343b8dcc3efa8502b98e24
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Enable ISH based on FW_CONFIG obtained from EC CBI. This is useful in
case device is a tablet and motion sensors are handled by ISH instead
of EC.
BUG=b:280329972,b:283023296
TEST= Set bit 21 of FW_CONFIG with CBI
Boot rex board
Check that ISH is enabled and loaded
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Ibe0e1b8ce2c9b08ac6b1e6fef9bd19afc9b4f59f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75039
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix for the "Onboard Keyboard and Type-C ports are not working after
resuming from powerd_dbus_suspend" issue. This issue was caused since
FSP 3165 FSP was fixed and started skipping GpioConfigureIoStandbyState
programming when GpioOverride UPD is enabled.
This patch moves the IO Standby State programming that FSP was doing to
coreboot.
BUG=b:284264580
TEST=Boot to OS, compare gpio pins, verify keyboard / Type-C
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If96c1e71fdde784a55fe079875915ffa5a4f548a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75555
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree config for ALC1019_ALC5682I_I2S
BUG=b:278169268
TEST=emerge-rex coreboot and verified on screebo
Change-Id: I2814cc76aff43daf0353cfef41592591bbe3d213
Signed-off-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
On Myst, the FSP is shutting down the PCIe lanes that the SSD is
on. Enable hotplug to force the FSP to keep the lanes active.
BUG=b:284213391
TEST=Boot to OS
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Iaf0aca329f05f15a3ce9edfa6a0e782c2edccabe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Enable s0ix on Myst.
BUG=b:277215113
TEST=builds
Change-Id: I3cabc2c3ba75f4490da18b861ef2b82ce240860d
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74279
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Google/Rex is built with Intel Meteor Lake-U SoC, so select it.
Currently, there is no functional difference, but in the future FSP
UPD parameters can be overridden properly.
BUG=b:276697173
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4c233e0a8ce58998dc1a0379662e386f9b3d0073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75612
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Create the karis variant of the rex0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:285195072
TEST=util/abuild/abuild -p none -t google/rex -x -a
make sure the build includes GOOGLE_KARIS
Change-Id: I16d8b43390401789b87a6233238e37f32a17b46b
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Generate RAM ID for Samsung K4UCE3Q4AB-MGCL
DRAM Part Name ID to assign
K4UCE3Q4AB-MGCL 3 (0011)
BUG=b:281950933
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I75818b8a34d010fc0efe90c7625162e40e3b0dca
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Generate RAM ID for Samsung K4UCE3Q4AB-MGCL
DRAM Part Name ID to assign
K4UCE3Q4AB-MGCL 3 (0011)
BUG=b:281943392
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I79b29b1195468272c7f64a0eeb15d032eff8c1d3
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
This patch adds FW_CONFIG to accommodate different Screebo BOM
components across various SKUs.
1. DB_CONFIG for DB_TPEC/DB_TBT/DB_UNKOWN
2. AUDIO for ALC1019_ALC5682I_I2S/AUDIO_UNKNOWN
BUG=b:278169268
TEST=build pass
Change-Id: I928aae61d4936509a7b68f4041c0cd72f298e83d
Signed-off-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow the eKTH7B18U_Product_Spec_V1.1 to add the device.
BUG=b:284381267
TEST=Check touch screen can detect in coreboot.
[INFO ] \_SB.I2C1.H010: ELAN Touchscreen at I2C: 02:10
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I4bd521410953892a477020a872de0d882001b178
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Follow the data sheet SA577C-12C0, Rev. 1.1 to add the device.
BUG=b:284381266
TEST=check touch pad can detect in coreboot.
[INFO ] \_SB.I2C0.D015: ELAN Touchpad at I2C: 01:15
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I0eb0ee1e6cb9c15bfe3964af6ce2ed02eee370a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Follow the schematic_0502 to add the audio codec and amp.
BUG=b:270109435
TEST=Check device can detect in coreboot.
[INFO ] \_SB.I2C3.RT58: Realtek RT5682 at I2C: 04:1a
[INFO ] \_SB.I2C3.D029: Realtek SPK AMP R at I2C: 04:29
[INFO ] \_SB.I2C3.D02A: Realtek SPK AMP L at I2C: 04:2a
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Icfec8d99be8fde986c5516e0c4cd50dae1edfa98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75477
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power sequence of the panel [1] and PMIC datasheet [2],
the power on T2 sequence VSP to VSN should be large than 1ms, but it's
-159us now, and the power off T2 sequence VSP to VSN should be large
than 0ms, but it's less than 0 now. Let's modify the power sequence
to meet the datasheet requirement.
[1] HX83102-J02_Datasheet_v03.pdf
[2] TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:282902297
TEST=power sequence T2 pass
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Ib1625c6a211f849071393f69eaf5c649a8e7f72e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75298
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
