summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2017-04-14mainboard/google/eve: Remove ACPI ALS deviceDuncan Laurie
Remove the ACPI ALS device from the EC configuration because this system has an ALS that is presented through the new EC sensor interface rather than the legacy ACPI interface. BUG=b:37179776 BRANCH=none TEST=Boot an Eve device and ensure that 'acpi-als' device is not present in /sys/bus/iio/devices. Change-Id: Ie18b8a661e4d16464784ca8a227586036e7631de Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19265 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-14mainboard/google/eve: Set UART0 to skip initialization in FSPDuncan Laurie
Set UART0 to "PchSerialIoSkipInit" so the pins for this device are not set back to native mode by FSP when configured as GPIO input by coreboot. Now that FSP is not touching the pins I also removed the workaround to reconfigure the pins after FSP. BUG=b:35647877 BRANCH=none TEST=Verify that GPP_C8-GPP_C11 are configured as GPIO input once the OS is booted and they are not set back to native function by FSP. Change-Id: Ifec4fa3e66ceeb660bad00c66bc7bd44bb457a01 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19264 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-14mainboard/google/eve: Enable internal pull-down on USB_C{0,1}_DP_HPDDuncan Laurie
These lines act as inputs to both EC and AP and when the corresponding TCPC mux is in low power mode the line is floating. Add an internal pull-down to each GPIO to prevent it from floating in this state. BUG=b:35775012 BRANCH=none TEST=Verify that the kernel does not see a device present on DP when the TCPC mux is in low power mode. Change-Id: Ie229f84871e9994467c0ab660cc7e271a51d9cbb Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19263 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-13mainboard/google/reef: Configure sdcard card detect (CD) pin GPIO_177Venkateswarlu Vinjamuri
This configures GPIO_177 as native function. This enables OS to boot from sdcard. BUG=b:35648535 TEST=Check OS boot from sdcard. Change-Id: I73901d4a1b39752cbc452f3286d494587dac95d4 Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/18948 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
2017-04-13mainboard/google/snappy: Increase weida touchscreen reset delayWisley Chen
Weida touchscreen controller needs 130 ms delay after reset BUG=b:35586513 BRANCH=reef TEST=Verified that touchscreen works on power-on and suspend/resume on snappy. Change-Id: I8418e742a69a2d6395baa2799a4da42a9bb5b312 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/19245 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-13google/eve: Disable Deep S3 in AC modeDuncan Laurie
In order to support a standard "docked" config disable Deep S3 when connected to AC power. This allows USB devices to wake the device from suspend if it is externally powered, but still retains the lower power state when running on battery. BUG=b:36723679 BRANCH=none TEST=manual testing on Eve for USB wake behavior: 1) when suspended on battery USB keyboard does not wake 2) when suspended while connected to AC a USB keyboard does wake 3) if suspended with AC, and then AC is removed, system does not wake with USB keyboard 4) if suspended without AC, and then AC is added, system does not wake with USB keyboard (it cannot get enabled without waking and re-suspending) Change-Id: I670e39d42cdb5b80612206da899be82ef3b2cbf2 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19240 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-13google/eve: Enable WiFi SAR featureDuncan Laurie
Enable the Intel WiFi SAR feature for Eve, which will be used to provide wifi power tables based on values read from VPD. This is enabled based on CONFIG_CHROMEOS because it relies on the presence of VPD code from vendorcode/google/chromeos. BUG=b:36727652 BRANCH=none TEST=test on Eve by setting "wifi_sar" in VPD and ensuring that the ACPI WIFI device gets the expected "WRDS" and "EWRD" tables with the values that were set in VPD. Change-Id: I11c129baca891221177575108ac09ba1707b516e Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19241 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-13soc/intel/skylake: Split AC/DC settings for Deep Sx configDuncan Laurie
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled in both DC and AC states. However since using Deep S3 disables some expected features like wake-on-USB it is not always desired to enable the same state in both modes. To address this split the setting and add a separate config for Deep Sx in AC and DC states. All motherboards that set this config were updated, but there is no actual change in behavior in this commit. BUG=b:36723679 BRANCH=none TEST=This commit has no runtime visible changes, I verified on Eve that the Deep SX config registers are unchanged, and it compiles for all affected boards. Change-Id: I590f145847785b5a7687f235304e988888fcea8a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19239 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-04-13mainboard/google/poppy: Enable internal pull-down on USB_C{0,1}_DP_HPDFurquan Shaikh
These lines act as inputs to both EC and AP. Thus, add internal pull-downs to prevent them from floating. BUG=b:35648530 Change-Id: I42326c810775d5449e99e52e81870970247ce335 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19243 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-13mainboard/google/poppy: Add support for cr50 SPI TPMFurquan Shaikh
Put all configs required for enabling cr50 SPI TPM on poppy under POPPY_USE_SPI_TPM so that it can be enabled any time for testing SPI TPM on this board. Also, add required callback for irq status and devicetree config for GSPI0. BUG=b:36873582 Change-Id: I67793093c006c1325fc16f669a96126525f83243 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19238 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-11scarlet/gru: skip display because mipi driver not readyShunqian Zheng
Scarlet don't have eDP and MIPI driver is not ready, skipping display for now or else Scarlet would be stuck in reading eDP HPD because there even not power for it. TEST=boot to kernel on Scarlet Change-Id: I02ab4ef21bf77b98414f537aca57b46c11922348 Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com> Reviewed-on: https://review.coreboot.org/19237 Tested-by: build bot (Jenkins) Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-04-11google/eve: Limit memory SKU 5 to 1600MHzDuncan Laurie
Due to issues with stability limit the SKU with K4EBE304EB-EGCF memory to 1600MHz instead of 1866MHz. BUG=b:37172778 BRANCH=none TEST=pass stress testing on devices with this memory Change-Id: I02af7e9c35e2c5b0b85223d58025cbd29841d973 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19227 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-04-10google/eve: Update I2C bus timingDuncan Laurie
Update the I2C rise/fall timings based on newly measured values on a new board with updated pull-up resistor values. Touchscreen: rise time 98ns, fall time 38ms Touchpad: rise time 111ns, fall time 41ns TPM: rise time 112ns, fall time 34ns BUG=b:35583133 BRANCH=none TEST=Each I2C bus frequency was verified on a scope to be ~400MHz Change-Id: Ibb3a15fa0cc862f36c1b9c63ac7847221020c4c0 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/19202 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-083rdparty/libgfxinit: Update submodule pointerNico Huber
Some renamings force us to update our code: * Scan_Ports() moved into a new package Display_Probing. * Ports Digital[123] are called HDMI[123] now (finally!). * `Configs_Type` became `Pipe_Configs`, `Config_Index` `Pipe_Index`. Other noteworthy changes in libgfxinit: * libgfxinit now knows about ports that share pins (e.g. HDMI1 and DP1) and refuses to enable any of them if both are connected (which is physically possible on certain ThinkPad docks). * Major refactoring of the high-level GMA code. Change-Id: I0ac376c6a3da997fa4a23054198819ca664b8bf0 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/18770 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-04-06gru: Initialize I2C bus for ARC2C0608Philip Chen
BUG=b:35583511 TEST=check i2c bus 0 initializes from ap console log Change-Id: Ibb6709159f5ed28ad0b62397d2ddb504dec55167 Signed-off-by: Philip Chen <philipchen@google.com> Reviewed-on: https://review.coreboot.org/19105 Tested-by: build bot (Jenkins) Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-04-05mainboard/google/reef: increase trackpad data hold timeAaron Durbin
Even though the i2c spec has no minimum data hold time in fast mode the trackpad vendor indicates 300ns is their minimum. However, the topology of the board uses FET isolation to cross voltage domains. Therefore, the default 300ns which should work isn't reflected on the device side of the voltage isolation circuit. Therefore, increase the data hold time to show an observed data hold time of more than 300ns on the device side. BUG=b:36469182 Change-Id: I1b70f2f53c5a29cc7cfd5035a71ca5811b3bcba0 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19065 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-04-05mainboard/google/poppy: Change SD card detect to GPP_E15Furquan Shaikh
SD card detect pin is moved to GPP_E15 in the next build. Update device tree and gpio config accordingly. BUG=b:36012095 Change-Id: Ic0ff72cdcb0f1ca27abc7eb8da9ccd8a21b28522 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/19107 Tested-by: build bot (Jenkins) Reviewed-by: Naresh Solanki <naresh.solanki@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.corp-partner.google.com>
2017-03-29mainboard/google/reef: turn off DMIC_CLK_B1 in S0ixSathyanarayana Nujella
Wake On Voice stream capture configuration is mono. It is sufficient to keep DMIC_CLK_A1 on in S0ix; so, turning off DMIC_CLK_B1. Power saving should be visible in the boards which has more than one DMIC connected. BUG=None BRANCH=None TEST=WoV and quad channel DMIC capture works Change-Id: Ic46d4c7b30b945eba47a05d78386f48e4a675a03 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/19018 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Tested-by: build bot (Jenkins)
2017-03-28vboot: Move remaining features out of vendorcode/google/chromeosJulius Werner
This patch attempts to finish the separation between CONFIG_VBOOT and CONFIG_CHROMEOS by moving the remaining options and code (including image generation code for things like FWID and GBB flags, which are intrinsic to vboot itself) from src/vendorcode/google/chromeos to src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig options, and clean up menuconfig visibility for them (i.e. some options were visible even though they were tied to the hardware while others were invisible even though it might make sense to change them). CQ-DEPEND=CL:459088 Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18984 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-28chromeos / broadwell / jecht: Make save_chromeos_gpios() jecht-specificJulius Werner
This callback was only required for a single mainboard, and it can easily be moved to mainboard-specific code. This patch removes it from the global namespace and isolates it to the Jecht board. (This makes it easier to separate vboot and chromeos code in a later patch.) Change-Id: I9cf67a75a052d1c86eda0393b6a9fbbe255fedf8 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18981 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-28vboot: Assume EC_SOFTWARE_SYNC and VIRTUAL_DEV_SWITCH by defaultJulius Werner
The virtualized developer switch was invented five years ago and has been used on every vboot system ever since. We shouldn't need to specify it again and again for every new board. This patch flips the Kconfig logic around and replaces CONFIG_VIRTUAL_DEV_SWITCH with CONFIG_PHYSICAL_DEV_SWITCH, so that only a few ancient boards need to set it and it fits better with CONFIG_PHYSICAL_REC_SWITCH. (Also set the latter for Lumpy which seems to have been omitted incorrectly, and hide it from menuconfig since it's a hardware parameter that shouldn't be configurable.) Since almost all our developer switches are virtual, it doesn't make sense for every board to pass a non-existent or non-functional developer mode switch in the coreboot tables, so let's get rid of that. It's also dangerously confusing for many boards to define a get_developer_mode() function that reads an actual pin (often from a debug header) which will not be honored by coreboot because CONFIG_PHYSICAL_DEV_SWITCH isn't set. Therefore, this patch removes all those non-functional instances of that function. In the future, either the board has a physical dev switch and must define it, or it doesn't and must not. In a similar sense (and since I'm touching so many board configs anyway), it's annoying that we have to keep selecting EC_SOFTWARE_SYNC. Instead, it should just be assumed by default whenever a Chrome EC is present in the system. This way, it can also still be overridden by menuconfig. CQ-DEPEND=CL:459701 Change-Id: If9cbaa7df530580a97f00ef238e3d9a8a86a4a7f Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18980 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-28vboot: Remove VBOOT_DYNAMIC_WORK_BUFFER Kconfig optionJulius Werner
VBOOT_DYNAMIC_WORK_BUFFER and VBOOT_STARTS_IN_ROMSTAGE are equivalent in practice. We can't have a dynamic work buffer unless we start in/after romstage, and there'd be no reason to go with a static buffer if we do. Let's get rid of one extra option and merge the two. Change-Id: I3f953c8d2a8dcb3f65b07f548184d6dd0eb688fe Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18979 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-28vboot: Select SoC-specific configuration for all Chrome OS boardsJulius Werner
Some Chrome OS boards previously didn't have a hardcoded vboot configuration (e.g. STARTS_IN_BOOTBLOCK/_ROMSTAGE, SEPARATE_VERSTAGE, etc.) selected from their SoC and mainboard Kconfig files, and instead relied on the Chrome OS build system to pass in those options separately. Since there is usually only one "best" vboot configuration for a certain board and there is often board or SoC code specifically written with that configuration in mind (e.g. memlayout), these options should not be adjustable in menuconfig and instead always get selected by board and SoC Makefiles (as opposed to some external build system). (Removing MAINBOARD_HAS_CHROMEOS from Urara because vboot support for Pistachio/MIPS was never finished. Trying to enable even post-romstage vboot leads to weird compiler errors that I don't want to track down now. Let's stop pretending this board has working Chrome OS support because it never did.) Change-Id: Ibddf413568630f2e5d6e286b9eca6378d7170104 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/19022 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-27ec: Use EC_ENABLE_LID_SWITCH for all mainboards with LID using chromeecFurquan Shaikh
Instead of defining a separate LID device for mainboards using chromeec, define EC_ENABLE_LID_SWITCH for these boards. Change-Id: Iac58847c2055fa27c19d02b2dbda6813d6dec3ec Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18964 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-27mainboard/google/rambi: Move SIO_EC_ENABLE_PS2K to onboard.hFurquan Shaikh
Instead of defining SIO_EC_ENABLE_PS2K by default for all boards and doing an undef in variant/onboard.h, move the definition of SIO_EC_ENABLE_PS2K to variant/onboard.h. This avoids dependency between different *.asl files. Change-Id: I83e4ce42a594e952a443c618d7ef9840113027b9 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18965 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-24mainboard/google/snappy: Update DPTF settingsWisley Chen
1. Remove CPU throttling effect of the charger sensor Refers Change-Id I267b6e07fa9def2c91ff9f6035f2d9437faf1965 (mb/google/reef: Remove CPU throttling effect of the charger sensor) to remove CPU throttling effect of the charger sensor since it's not relevant to throttle CPU based on the charger sensor. 2. Change TSR1 influence from 200 to 100 3. Change TSR2 sample period from 120s to 30s BUG=b:35585781 BRANCH=reef TEST=built, and verified on snappy by thermal team. Change-Id: Ic3fc51c4288b24f4e64950e5b148aed4495a1c3b Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18950 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2017-03-23google/fizz: Update device tree from schematicShelley Chen
BUG=b:35775024 BRANCH=None TEST=Compiles successfully Change-Id: I92cf9baa4c3aefc6983511543d875e74a6b0bf94 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18944 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-23google/fizz: Transfer gpio from schematicShelley Chen
Transfer the gpio assignments in the fizz schematic into gpio.h. BUG=b:35775024 BRANCH=None TEST=./util/abuild/abuild -p none -t google/fizz -x -a Change-Id: If05aa2859f2511c3f616dc3fb38bca4fb8524697 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18797 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-03-23google/fizz: Remove poppy-specific configsShelley Chen
- Remove spd files/directory - Remove audio blobs - Remove dptf.asl contents - Remove MKBP - Remove acpi table initialization BUG=b:35775024 BRANCH=None TEST=Compiles successfully Change-Id: I5d717d23224956ee1653c5ded28abd05cd254c3a Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18857 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-23google/fizz: Add new boardShelley Chen
Creating google/fizz directory based on poppy (using kabylake and FSP 2.0). Only making name changes and Copyright year changes. Many poppy-specific configs left in and will be updated in follup CLs. BUG=b:35775024 BRANCH=None TEST=Compile fizz board Change-Id: Icab3639a53fef65e904e797028916fda879fff7c Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/18796 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-22mainboard/google/reef: add nasher variantYH Lin
Create the initial Nasher variant which refers to the Reef. Nasher is APL board that derives from reference board Reef. BRANCH=master BUG=b:36389286 TEST=Build (as initial setup) Signed-off-by: YH Lin <yueherngl@chromium.org> Change-Id: I7962aa8246890149988c7f02dcd90d820df7b901 Reviewed-on: https://review.coreboot.org/18928 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-21google/pyro: Update DPTF settingsKevin Chiu
1. correct DPTF TCHG target device to TSR2 2. Refers Change-Id I267b6e07fa9def2c91ff9f6035f2d9437faf1965 (mb/google/reef: Remove CPU throttling effect of the charger sensor) to remove CPU throttling effect of the charger sensor since it's not relevant to throttle CPU based on the charger sensor. BUG=b:35586881 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: I4801e0e612e0ddf90764ffe080c679818d33212a Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18920 Tested-by: build bot (Jenkins) Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-21mainboard/google/poppy: Use sideband IRQ for SD Card DetectFurquan Shaikh
Since SD card controller is expected to enter D3hot by runtime power management if there is no card inserted, we need to use a sideband IRQ pin which is not under the control of the controller. Thus, configure GPP_A7 as the sideband IRQ pin and pass it to OS as the card detect pin. BUG=b:35586693 BRANCH=None TEST=Verified on a reworked poppy board that card detect works fine. Change-Id: I4512f5d7829583e27c9750463396eaffbc5702b4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18926 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-21google/sand: Add Raydium touchscreen deviceKatherine Hsieh
We just support Raydium touchscreen instead of Elan. Thus we have to remove Elan touchscreen device and add Raydium touchsrcreen device. BUG=b:35775065 BRANCH=reef TEST=emerge-sand coreboot Change-Id: I7b33a29287dcb90e379b52cc93825f2988a0d3c9 Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com> Reviewed-on: https://review.coreboot.org/18789 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-20mainboard/google/snappy: Update _hid name for weida touchscreenWisley Chen
Change hid name to "WDHT0002" for Weida WDT8752 which is supported by standard hid i2c Linux driver. BUG=b:35586513 BRANCH=reef TEST=build, boot on snappy, and verified acpi node "WDHT0002" created. Change-Id: Ie0cc980aa427b6db1eb14eb7868718619bb1310f Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18874 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-19mb/google/reef: Remove CPU throttling effect of the charger sensorSumeet Pawnikar
It's not relevant to throttle CPU based on the charger sensor. So, remove this CPU throttling effect. BUG=b:35908799 BRANCH=master TEST=Built and booted on Electro DUT Change-Id: I267b6e07fa9def2c91ff9f6035f2d9437faf1965 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18852 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
2017-03-17google/veyron: Clean out unused board variantsJulius Werner
We have code for certain Veyron variant names that were either never made into an actual board (Gus, Nicky, Thea) or used for Google-internal test boards that no longer exist (Pinky, Shark). Let's clean them out to avoid confusing people. Change-Id: Icdce5f0f3613e089d0994318b02dba54170f0c42 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18860 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-03-17google/veyron: Work around RAM code strapping errorJulius Werner
With a recent patch (google/veyron_*: Add new Micron and Hynix modules) we switched RAM codes for Veyron boards to tri-state since we were running out of binary numbers. Unfortunately we only tested that change on Minnie and Speedy, and it turns out that it broke Jaq, Jerry and Mighty. The "high" RAM code pins on those boards were incorrectly strapped with 100Kohm resistors (as opposed to 1Kohm on Minnie and Speedy), which is too high to overpower the SoC-internal pull-down we use to differentiate "high" from "tri-state". Since we already used tri-state codes on some Minnie and Speedy SKUs we have to hack up the code to work differently on these two groups of boards to keep everything working. BRANCH=veyron BUG=b:36279493 TEST=Compiled, confirmed ram_code called the right function depending on board. Change-Id: I253b213ef7ca621ce47a7a55a5119a167d944078 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18859 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-03-17mainboard/google/poppy: Enable EC SW syncFurquan Shaikh
Now that EC on poppy is stable, it is time to switch on EC SW sync. BUG=b:36178824 BRANCH=None TEST=Verified that EC SW sync is done properly and device boots to OS. Change-Id: I1395ad8af73128a8dd220351f5b5da157659b19e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18838 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-16google/poppy: Use rt5663 interrupt as GpioInt instead of PIRQRizwan Qureshi
The kernel driver for rt5663 expects to get an interrupt on both a rising and falling edge, and using a legacy interrupt doesn't provide that flexibility. Instead configure this pin as a GPIO and use the interrupt through the GPIO controller. This allows using GpioInt() with ActiveBoth setting and results in correct operation of the headset jack. This is a clone of Duncan's patch for eve at I6f181ec560fe9d34efc023ef6e78e33cb0b4c529 BUG=none BRANCH=none TEST=test on poppy that headset jack detect is read properly at boot, and that plugging in and removing both generate a single interrupt event in the driver. Change-Id: I4aaa4164cb277a98ab5d5f033632f5e16bfb779e Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18853 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-16google/eve: Use rt5663 interrupt as GpioInt instead of PIRQDuncan Laurie
The kernel driver for rt5663 expects to get an interrupt on both a rising and falling edge, and using a legacy interrupt doesn't provide that flexibility. Instead configure this pin as a GPIO and use the interrupt through the GPIO controller. This allows using GpioInt() with ActiveBoth setting and results in correct operation of the headset jack. BUG=b:35585307 BRANCH=none TEST=test on Eve that headset jack detect is read properly at boot, and that plugging in and removing both generate a single interrupt event in the driver. Change-Id: I6f181ec560fe9d34efc023ef6e78e33cb0b4c529 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18836 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-16mainboard/google/reef: Increase PL2 Max to 15WTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_DVT_v0.6_20170314.xlsx) 1. Increase PL2 Max to 15W. BUG=b:35583586 BRANCH=reef TEST=build and verify PL2 Max value on electro dut Change-Id: I13167e28267d5827d79a6bde31f077a01f2bd535 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18807 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-15google/eve: Update MCU GPIOs configurationVincent Palatin
Keep the BOOT0 pin triggering the MCU bootloader as an input, so the Servo debug board doesn't have to fight with the PCH to program it, the net already has an external pull-down to ensure that the MCU is in normal mode at boot. By default, do not drive the FP sensor reset from the PCH, the MCU is now managing the reset line (but the PCH still has a connection on the current boards). BRANCH=none BUG=b:36025702 TEST=manual testing, program the MCU through a Servo v2 board, and use the FP sensor through the MCU and verify it is not stuck under reset. Change-Id: I19113b5d78013d0ab6ec5a72c6f71dd4c67a88e8 Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: https://review.coreboot.org/18830 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-15google/eve: Apply default AC/DC loadline settingsDuncan Laurie
Set the AC and DC loadline values based on the KBL-Y 2+2 defaults that are applied by FSP. These will be tuned later and are exposed as defaults so the engineers know what to start with. BUG=b:36228330 BRANCH=none TEST=Build and boot on Eve and check debug FSP output to ensure that it is applying the provided loadline values Change-Id: Ieae4f2b201d8210e75bdb9438070a3a2e1fda6b7 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18820 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-03-15intel/skylake: Fix bug in VR configuration with FSP 2.0Duncan Laurie
With the move to FSP 2.0 the number of VR types supported was reduced to 4, and the VR_RING type is no longer present. This means all existing boards using FSP 2.0 are incorrectly passing VR configuration into FSP as the values corresponding to "GT Sliced" and "GT Unsliced" have changed. Fix this by updating the skylake SOC VR handling to account for changes in the FSP configuration and no longer provide VR_RING type when using FSP 2.0. BUG=b:36228330 BRANCH=none TEST=manual: build and boot on Eve Change-Id: I59eea9fba006a4c235d7b42d07fdc6e4f44f7351 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18818 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-03-15google/eve: Use rt5514 instead of 4ch DMICDuncan Laurie
On this platform the DMICs are connected to the rt5514 DSP instead of directly connected to the SOC. Use the new rt5514 NHLT blob instead of the 4ch DMIC blob and add the required I2C and SPI entries in devicetree so this can get probed properly. BUG=b:35585307 BRANCH=none TEST=build and boot on Eve P1 and check for rt5514 driver enumerated by the kernel Change-Id: I0f2cb532771ee1857df7f33c52a96acf96dc1f54 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18817 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-15mainboard/google/reef: Add FPF_STATUS FMAP regionAndrey Petrov
Add FPF_STATUS region under MISC_RW. The purpose of the region is to store FPF status. Change-Id: I2997b3d39a94bf444df51068f254edcf49c47afd Signed-off-by: Andrey Petrov <andrey.petrov@intel.com> Reviewed-on: https://review.coreboot.org/18773 Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-14google/sand: Remove support for tablet mode switchKatherine Hsieh
Sand is not convertible and no EC sensor sends event from EC to AP. That event default is tablet mode, we don't have to enable tablet event. Modify the ec.h, is based on <baseboard/ec.h> BUG=b:36108742 BRANCH=reef TEST=emerge-sand coreboot, boot to OS and touchpad and keyboard can work. Change-Id: I6b6b45b5b4daf2c430ed18130f39eab0bd9a9812 Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com> Reviewed-on: https://review.coreboot.org/18737 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-12google/poppy: Enable internal pull-up on PWRBTN#Shobhit Srivastava
Enable an internal pull-up on the power button input as short press is resulting in power button override being asserted. BUG=b:36111214 BRANCH=none TEST=tested on poppy board to ensure quick power button press does not result in a shutdown due to power button override. Change-Id: I3a25b78562e2302b6f7575e64c87ae8142690701 Signed-off-by: Shobhit Srivastava <shobhit.srivastava@intel.com> Reviewed-on: https://review.coreboot.org/18734 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-10google/sand: Add devicetree.cb file for sandKatherine Hsieh
It is a copy from baseboard/devicetree.cb (coreboot.org ToT) BUG=b:35775065 BRANCH=reef TEST=emerge-sand coreboot Change-Id: I5ba86e54ccfbf5af7bf0e9ad8fe7bf22020e48ee Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com> Reviewed-on: https://review.coreboot.org/18703 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-10mainboard/google/reef: Modify TCPU, TSR2 and TRT tableTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT2_v0.5_20170306.xlsx) 1. Update DPTF TCPU critical trigger point. TCPU critical point: 105 2. Update DPTF TSR2 passive trigger point. TSR2 passive point: 58 3. Change thermal relationship table (TRT) setting. Change CPU Throttle Effect on CPU sample rate to 10secs. Change Charger Effect on Temp Sensor 2 sample rate to 30secs. Change CPU Effect on Temp Sensor 2 sample rate to 60secs. BUG=b:35583586 BRANCH=master TEST=build and boot on electro dut Change-Id: I85564ccdaf327eeaa13bf1f31d9a933609a21582 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18610 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-10mainboard/google/reef: Configure SDCARD card detect pinVenkateswarlu Vinjamuri
This configures GPIO_177 as an input pin for SDCARD card detect. This also changes the ownership of the pin from ACPI to GPIO driver. Assign the sdcard card detect pin in devicetree for reef variants. CQ-DEPEND=448173 BUG=chrome-os-partner:63070 TEST=None Change-Id: Ia8aef60bd7d0ea36afb39f76fab051aa46a2ed64 Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/18497 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-09drivers/spi/tpm: provide Kconfig to indicate CR50 usageAaron Durbin
Going forward it's important to note when a CR50 is expected to be present in the system. Additionally, this Kconfig addition provides symmetry with the equivalent i2c Kconfig option. BUG=b:35775104 Change-Id: Ifbd42b8a22f407534b23459713558c77cde6935d Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18680 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-03-09mainboard/google/reef: increase pre cbmem console size for Chrome OSAaron Durbin
verstage can be pretty chatty so bump the pre cbmem console size when building for Chrome OS so that all messages can be observed. BUG=b:35775104 BRANCH=reef TEST=Booted and noted no cutoff of console when sec data being saved. Change-Id: I0ce2976572dedf976f051c74a3014d282c3c5f4c Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18679 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-09google/poppy: Configure SRCCLKREQ4 as No ConnectNaresh G Solanki
SRCCLKREQ4 is unused, so configure SRCCLKREQ4 as NC (No Connect). Change-Id: I6e265b9c9faa0df20208bb82278cadbbbbe6c537 Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/18589 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-09google/pyro: Update DPTF settingsKevin Chiu
1. Update DPTF TSR1 passive trigger points. TSR1 passive point: 50 2. Update DPTF PL1 Minimum PL1 min: 2.5W BUG=b:35586881 BRANCH=reef TEST=emerge-pyro coreboot Change-Id: Ia2634f40098d026c4d228fab4b7c05501c1ff05f Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/18699 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-09mainboard/google/poppy: Enable cros_ec_keyb deviceFurquan Shaikh
This is required to transmit button information from EC to kernel. BUG=b:35774934 BRANCH=None TEST=Verified using evtest that kernel is able to get button press/release information from EC. Change-Id: I8f380f935c2945de9d8e72eafc877562987d02db Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18642 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-08mainboard/google/poppy: Add EC_HOST_EVENT_MODE_CHANGE to wakeup sourceFurquan Shaikh
Allow EC mode change event to wake AP up in S3. BUG=b:35775085 BRANCH=None TEST=Compiles successfully for poppy. Change-Id: I6f1546c60aef6620e22cdce2fab3a2709e6556a1 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18608 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-08google/eve: Configure GPIOs for new boardDuncan Laurie
A new board revision is making use of two previously unused GPIOs to drive BOOT/RESET pins to an on-board MCU. The reset pin is open drain so it is set as input by default, and the boot pin is driven low by default. Since these are UART0 pins they also need to be set up again after executing FSP-S as it will change them back to native mode pins. BUG=b:36025702 BRANCH=none TEST=manual testing on reworked board, toggling GPIOs to put the MCU into programming mode. Change-Id: Id6f0ef2f863bc1e873b58e344446038786b59d25 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18661 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-03-08mainboard/google/snappy: Override USB2 phy settingWisley Chen
Fine tune USB2, need to override the following registers. port#1: PERPORTPETXISET=7 PERPORTTXISET=0 BUG=b:35858164 BRANCH=reef TEST=built, measured eye diagram on snappy, and reviewed by intel Change-Id: I461cf8f032b4e70abc9707e6cd3603a62cee448f Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18590 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-07google/gru: add MAX_SDRAM_FREQ config to choose max ddr freqShunqian Zheng
Gru/Kevin use 933 MHz (actually 928 MHz for better jitter) as max sdram frequency, while bob uses 800 MHz. It's normal some variants can't meet 928 MHz SI requirement and hence have to use a lower freq as spec. BUG=chrome-os-partner:61001 BRANCH=gru TEST=check dpll is 800 MHz on bob Change-Id: I6d19a351f25d1f48547715ce57c3a87d9505f6f1 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 8176bfea52422c713f144ffec419752aeca66db2 Original-Change-Id: I46afba8d091f1489feeb20cafc44decaa81601fc Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/420208 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Commit-Queue: Shasha Zhao <Sarah_Zhao@asus.com> Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-(cherry picked from commit eba5dff79eeedae5ff608d2d8d297ccf9c13cb55) Original-Reviewed-on: https://chromium-review.googlesource.com/448277 Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org> Reviewed-on: https://review.coreboot.org/18581 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/veyron: add K4B4G1646E-BYK0 ddr with ramid 000ZShunqian Zheng
The K4B4G1646E-BYK0 shares sdram config with K4B4G1646D-BYK0. For clarity, sdram-ddr3-samsung-2GB now is used by - K4B4G1646D-BYK0 - K4B4G1646E-BYK0 - K4B4G1646Q-HYK0 BUG=chrome-os-partner:62131 BRANCH=veyron TEST=emerge Change-Id: Ie43f23bf8f5f5b1acbb74c85cac17fe181c841c4 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 46d62d87101e0ee1050b00db02b3ecaa4587e9f4 Original-Change-Id: I461c6f36c28ea0eeaf7d64292c9c87ab0c9de443 Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/446197 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-(cherry picked from commit f98251a4a4fe4d49721a936a684f6ac80f3f6405) Original-Reviewed-on: https://chromium-review.googlesource.com/446300 Reviewed-on: https://review.coreboot.org/18519 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/veyron_*: Add new Micron and Hynix modulesDavid Hendricks
This adds SDRAM entries for the following modules: - Micron: DDMT52L256M64D2PP-107 - Hynix: H9CCNNNBKTALBR-NUD They are compatible with Samsung K4E8E324EB-EGCF, so this just copies sdram-lpddr3-samsung-2GB-24EB.inc and changes the name used in the comment near the top. Notes on our "special snowflake" boards: - veyron_danger's RAM ID is hard-coded to zero, so I skipped changes involving the binary first numbering scheme. - Rialto's SDRAM mapping is different, so I padded its SDRAM entries to 24 to match other boards. - veyron_mickey requires different MR3 and ODT settings than other boards due to its unique PCB (chrome-os-partner:43626). BUG=chrome-os-partner:59997 BRANCH=none TEST=Booted new modules on Mickey (see BUG) Change-Id: If2e22c83f4a08743f12bbc49b3fabcbf1d7d07dd Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 35cac483e86e57899dbb0898dad3510f4c2ab2d3 Original-Change-Id: I22386a25b965a4b96194d053b97e3269dbdea8c7 Original-Signed-off-by: David Hendricks <dhendrix@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/412328 Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Original-Commit-Queue: Jiazi Yang <Tomato_Yang@asus.com> Original-Tested-by: Jiazi Yang <Tomato_Yang@asus.com> Original-(cherry picked from commit bd5aa1a5488b99f2edc3e79951064a1f824062f6) Original-Reviewed-on: https://chromium-review.googlesource.com/446299 Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com> Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18518 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-03-07google/poppy: fix finger print sensor interrupt gpio configurationRizwan Qureshi
Configure the right GPIOs for finger print sensor interrupt and reset lines. As per the schematics GPP_C8 is for sensor interrupt and GPP_C9 is for sensor reset. Change-Id: Ib25c68ec2fe20b1302b6170d67ceab7e8cca1a83 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18389 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-02mainboard/google/poppy: Disable deep S3 on poppyFurquan Shaikh
BUG=chrome-os-partner:62963 BRANCH=None TEST=Compiles successfully Change-Id: Icb929262fd67362b8e5c5cf31dce04ab1f496695 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18467 Tested-by: build bot (Jenkins) Reviewed-by: Rajat Jain <rajatja@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-25mainboard/google/reef: keep LPSS_UART2_TXD high in suspend stateAaron Durbin
The cr50 part on reef is connected to the SoC's UART lines. However, when the tx signal is low it causes an interrupt to fire on cr50. Therefore, keep the tx signal high in suspend state so that it doesn't cause an interrupt storm on cr50 which prevents cr50 from sleeping. BUG=chrome-os-partner:63283 BRANCH=reef TEST=s0ix no longer causes interrupt storm on cr50. Power consumption normal. Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18491 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-25google/eve: Add rise/fall times for I2C busesDuncan Laurie
Apply tuning for the PCH I2C buses on Eve based on rise/fall time measurements that were done with a scope. BUG=chrome-os-partner:59686 BRANCH=none TEST=Manual testing on Eve P1 to verify that all devices on I2C buses are still functional. Post-tuning measurement will be done once a new firmware is released. Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18487 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-24mainboard/google/poppy: Change touchscreen IRQ to level-triggeredFurquan Shaikh
BUG=chrome-os-partner:62967 BRANCH=None TEST=Verified that touchscreen works on power-on and after suspend-resume as well. Change-Id: Id674cbcc2d524a6ed2883bf9f0e9e076890f9a85 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18466 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-23google/gru: whitespace fixPatrick Georgi
Follow up to https://review.coreboot.org/#/c/18460/ Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18475 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection thresholdWilliam wu
According to USB 2.0 Spec Table 7-7, the High-speed squelch detection threshold Min 100mV and Max 150mV, and we set USB 2.0 PHY0 and PHY1 squelch detection threshold to 150mV by default, so if the amplitude of differential voltage envelope is < 150 mV, the USB 2.0 PHYs envelope detector will indicate it as squelch. On Kevin board, if we connect usb device with Samsung U2 cable, we can see that the impedance of U2 cable is too big according to the eye-diagram test report, and this cause serious signal attenuation at the end of receiver, the amplitude of differential voltage falls below 150mV. This patch aims to reduce the PHY0 and PHY1 otg-ports squelch detection threshold to 125mV (host-ports still use 150mV by default), this is helpful to increase USB 2.0 PHY compatibility. BRANCH=gru BUG=chrome-os-partner:62320 TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into Type-C port, check if the USB device can be detected. Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/431015 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Inno Park <ih.yoo.park@samsung.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18462 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2017-02-23google/gru: update the pwm regulatorCaesar Wang
As David commented the "Bob and other follow-ons match Gru, Kevin should be the special case here", and update the calculations value for gru/bob board. From the actual tests, some regulator voltage than the actual set of less than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the {min, max} regulator voltage for Bob board. Make sure we get the accurate voltage. BUG=chrome-os-partner:61497 BRANCH=none TEST=boot up Bob, measure the voltage for little cpu and C-logic. Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4 Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/424523 Original-Reviewed-by: David Schneider <dnschneid@chromium.org> Original-Reviewed-by: Brian Norris <briannorris@chromium.org> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430403 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18460 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mb/google/poppy: Enable support for DPTFSumeet Pawnikar
This patch adds the DPTF settings specfic to the mainboard and enables the CPU and other thermal sensors as participant device for poppy. It enables the DPTF flag in the device tree for poppy. It also includes the DPTF specific ASL file in the main DSDT definition. BUG=None BRANCH=None TEST=Built for poppy. Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36 Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17926 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-23google/oak: Add initial support for RowanYidi Lin
Update GPIO controls and mainboard configurations for Rowan. [pg: use the opportunity to clean-up the gerrit-rebase task list with the entirely unrelated Ignore-CL-Reviewed-on lines] BUG=chrome-os-partner:62672 BRANCH=none TEST=emerge-rowan coreboot Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1 Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830 Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430557 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822 Reviewed-on: https://review.coreboot.org/18463 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: improve eye diagram for passing the testCaesar Wang
The children of Gru should share the benefits. In the real world, Bob can't pass the eye diagram tests. BUG=chrome-os-partner:62714 BRANCH=firmware-gru-8785.B TEST=build coreboot Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/440745 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/441468 Reviewed-on: https://review.coreboot.org/18461 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22acpi: Add ACPI_ prefix to IRQ enum and struct namesFurquan Shaikh
This is done to avoid any conflicts with same IRQ enums defined by other drivers. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18444 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22google/gru: Fix whitespacePatrick Georgi
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18322 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Realtek 5663 supportRizwan Qureshi
Enable Realtek RT5663 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=With required driver support in kernel verify audio on headset Change-Id: I9b9eb1e7edca56870f5be0e4fd603c9b0dc7f9de Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18216 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Maxim MAX98927 codecRizwan Qureshi
Enable Maxim 98927 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=with required driver support in kernel verify audio on poppy on-board speakers. Change-Id: Id731de42d77204d59f32ac4c33a245837d6e2107 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Dylan Reid <dgreid@chromium.org> Reviewed-on: https://review.coreboot.org/18215 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Generate required nhlt tableRizwan Qureshi
poppy board uses Maxim 98927 speaker codec and Realtek RT5663 for headset. Select the apropriate NHLT blobs to be packaged in CBFS. Also, generate the required ACPI NHLT table for codec and the supported topology in poppy. BUG=chrome-os-partner:62051 BRANCH=None TEST=With the required driver support in kernel verify that the Audio plays on on-board speakers and headset, recording works from on-board mics and headset mics. Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed Signed-off-by: M Naveen <naveen.m@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/18214 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20drivers/i2c: Use I2C HID driver for wacom devicesFurquan Shaikh
Wacom I2C driver does the same thing as I2C HID driver, other than defining macros for Wacom HID. Instead of maintaining two separate drivers providing the same functionality, update all wacom devices to use generic I2C HID driver. BUG=None BRANCH=None TEST=Verified that ACPI nodes for wacom devices are unchanged. Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18401 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/eve: Set touchscreen I2C bus speed to 1MHzDuncan Laurie
Enable Fast-Plus speed for the touchscreen device so it can be used at 1MHz instead of 400KHz. BUG=chrome-os-partner:61277 TEST=manual testing on Eve P1, needs backported kernel patches to actually make use of any I2C speed other than 400KHz Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18397 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20google/eve: Add audio devicesDuncan Laurie
Add the audio devices to Eve mainboard: - Describe Maxim 98927 speaker amps and RT5663 headphone codec in ACPI so they can be enumerated by the OS. - Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH. BUG=chrome-os-partner:61009 TEST=manual testing on Eve P1 with updated kernel to ensure that both speakers and headset are functional. DMIC support is is still being worked on and is not yet functional. Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18398 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-02-20mainboard/{google,intel}: Change config option selectionFurquan Shaikh
Change config option selection from "config xyz default y" to "select xyz" if the config option has no dependencies. BUG=None BRANCH=None TEST=Verified that config option selection remains unchanged. Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18400 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20mainboard/google/reef: Remove config DRIVERS_GENERIC_GPIO_REGULATORFurquan Shaikh
Since we are not using gpio regulators on reef anymore, remove the selection from Kconfig as well. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18399 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/slippy: consolidate variants' common mainboard.asl codeMatt DeVillier
Move code common code from each variant's mainboard.asl into common ACPI code for all variants (like google/auron). This also adds the _PRW method for the LID0 device for falco and peppy, which omitted the function when they were originally upstreamed. See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18368 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20google/eve: Set rise/fall timing values for I2C bus 1Duncan Laurie
Apply the measured rise and fall times for I2C bus 1 on Eve so it can be tuned properly for 400KHz operation. BUG=chrome-os-partner:63020 TEST=verify I2C1 bus speed with a scope Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18396 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-20google/eve: Fix FPC supportDuncan Laurie
Currently UART0 GPIOs are being put into native mode during FSP-S stage, so have ramstage re-configure them back to regular GPIO mode. GPP_C8 does not seem to be functioning properly when routed to the APIC, possibly due to the UART0 being enabled even though it is unused, which is required because UART0 is PCI 1e.0 and so must be present for other 1e.x functions to be enumerated. Instead, use this pin as a GPIO interrupt so it will be routed through the GPIO controller at IRQ 14. GPP_C9 was inverted and was only working because the pin was being re-configured in FSP-S. Also export the reset gpio as a device property so it can be used by the kernel driver, which will stop it from complaining at boot. BUG=chrome-os-partner:61233 TEST=verify that the interrupt and device is functional in the OS Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18395 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/eve: select SOC_INTEL_KABYLAKERizwan Qureshi
eve is based on Kabylake SoC hence select the appropriate config. Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18314 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/poppy: select SOC_INTEL_KABYLAKERizwan Qureshi
poppy is based on Kabylake SoC hence select the appropriate config. Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18313 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/google/poppy: Generate digitizer node in SSDTFurquan Shaikh
Add support for generating digitizer node in SSDT using wacom i2c driver. BUG=None BRANCH=None TEST=Verified that the node shows up in SSDT. Change-Id: If7e1e2463778c2ff7263eff995def149457edcde Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18373 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-16mainboard/google/eve: Generate FPC device using SPI SSDT generatorFurquan Shaikh
Use the newly added SPI SSDT generator for adding FPC device. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Verified that the SSDT entry matches the entry in mainboard.asl Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18343 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-15mainboard/google/reef: add sand variantYH Lin
Create the initial Sand variant which refers to the Reef. Sand is APL board that derives from reference board Reef. BRANCH=master BUG=chrome-os-partner:62200 TEST=Build (as initial setup) Signed-off-by: YH Lin <yueherngl@chromium.org> Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625 Reviewed-on: https://review.coreboot.org/18324 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/eve: change touchpad HIDWei-Ning Huang
Change touchpad HID to use with the Google Centroiding Touchpad driver. BUG=chrome-os-partner:61088 TEST=`emerge-eve coreboot` Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f Signed-off-by: Wei-Ning Huang <wnhuang@google.com> Reviewed-on: https://review.coreboot.org/18359 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-14google/rambi: add explicit pull-down for ram-idMatt DeVillier
Some variants need the internal pull resistor on GPIO_SSUS_40 set explicitly to pull down rather than disabling the pull, in order for the ram-id to be read correctly via GPIO. Correct this by adding a function to enable and set the internal pull and define its use as needed in the board's variant.h. Chromium source: branch: firmware-gnawty-5216.239.B /src/soc/intel/baytrail/baytrail/gpio.h#418 /src/mainboard/google/gnawty/romstage.c#60 Test: boot 4GB Candy board and observe correct RAM id, amount detected Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18309 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-14google/poppy: select NO_FADT_8042Jenny TC
Poppy doesn't support 8042 keyboard. Select NO_FADT_8042 to disable 8042 in FADT header. Kernel will not try to access 8042 region if 8042.FADT=0 BUG=chrome-os-partner:61858 TEST=Boot OS and verify FADT 8042 flag Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d Signed-off-by: Jenny TC <jenny.tc@intel.com> Reviewed-on: https://review.coreboot.org/18311 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-13mainboard/google/snappy: Update DPTF settingsWisley Chen
Update DPTF parameters based on thermal team test result. 1. Update TSR2 trigger points. TSR2 passive point: 70, critical point: 90 2. Set PL2 Max to 15W. BUG=chrome-os-partner:61383 BRANCH=reef TEST=build, boot on snappy, and verified by thermal team Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42 Signed-off-by: Wisley Chen <wisley.chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18318 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-11mainboard/google/reef: Increase PL1 sampling periodSumeet Pawnikar
Performance degradation seen with current PL1 throttling rate as 8 seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1 throttling rate to 15 seconds, fps score improved. BUG=chrome-os-partner:60038 BRANCH=reef TEST=Built and tested on electro system Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18317 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2017-02-11google/gru: add scarlet variantphilipchen
There will be more follow-up changes. BUG=chrome-os-partner:62377 BRANCH=None TEST=emerge-scarlet coreboot libpayload Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a Original-Signed-off-by: philipchen <philipchen@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/433039 Original-Commit-Ready: Philip Chen <philipchen@chromium.org> Original-Tested-by: Philip Chen <philipchen@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18296 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2017-02-07mainboards/google/reef: Add support for tablet mode switch.Gwendal Grignou
Reef is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06 Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18277 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-07google/eve: Add support for tablet mode switch.Gwendal Grignou
Eve is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18276 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 11:19:32 +0000