| Age | Commit message (Collapse) | Author |
|---|
|
TEST=Boot from scarlet, and mipi panel work
Change-Id: Id5f81867ea50f72cc0bc13074627134e0dc198ba
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update the DPTF parameters based on thermal test result.
1. Update DPTF CPU/TSR0/TSR1/TSR2 passive/critial trigger points.
CPU passive point:83, critial point:99
TSR0 passive point:60, critial point:70
TSR1 passive point:50, critial point:90
TSR2 passive point:77, critial point:90
2. Update PL1/PL2 Min Power Limit/Max Power Limit
Set PL1 min to 4W, max to 12W, and step size to 0.2W
3. Change thermal relationship table (TRT) setting.
Change CPU Throttle Effect on CPU sample rate to 5secs
Change CPU Effect on Temp Sensor 0 sample rate to 60secs
The TRT of TCHG is TSR1, but real sensor is TSR2. sample rate to 30secs
Change Charger Effect on Temp Sensor 2 sample rate to 30secs
Change CPU Effect on Temp Sensor 2 sample rate to 120secs
BUG=None
TEST=build and boot on electro dut
Change-Id: I0ea0bab7fa6b0ad75d9ddacbd7cd882f91e4b0db
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/19538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Turn on device 1c.0 in order to enable devices
under it.
BUG=b:37486021, b:35775024
BRANCH=None
TEST=Boot from NVMe
Change-Id: Ide66823283c58d2bea0c9886f762f0581741affe
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19533
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is required to ensure that SCI is generated whenever a host event
is set for MODE_CHANGE. Thus, when wake from MODE_CHANGE event occurs,
eSPI SCI is generated which results in kernel handler reading host
event from the EC and thus causes the wake pin to be de-asserted.
BUG=b:37223093
TEST=Verified that wake from mode change event works fine in suspend
mode and there is no interrupt storm for GPE SCI after resume.
Change-Id: I1dd158ea0e302d5be9bcaa531cd1851082ba59fd
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jenny Tc <jenny.tc@intel.com>
|
|
Remove the code that was enabling the keyboard backlight at boot
since this is not desired behavior for this device.
BUG=b:35581264
TEST=build and boot on Eve and ensure keyboard backlight does
not turn on when booting but can still be enabled in the OS.
Change-Id: I7229cf962597c0de74dc005f7afb9408f7a66f42
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set GPP_A13/SUSWARN# pin mode to native function 1. This pin is tied
to SUSACK# in the schematic and and is intented to be used in Deep Sx
so it should not be configured for GPIO mode.
BUG=b:35581264
TEST=build and boot on Eve platform, test that Deep S3 and Deep S5
are still functional. (this change should have no visible effect)
Change-Id: Ie2dc24d095872ab93a5bfcbe5307c3b7a8e4dbcc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Board Scarlet doesn't use usbphy1.
BUG=b:37685249
TEST=boot Scarlet, check the firmware log, and confirm
no errors about USB1
Change-Id: I66e0d8a235cc9057964f7abca32bc692d41e88fd
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
1. Add support for using cr50 I2C TPM on poppy. This will not be
enabled until the next build.
2. Also, configure GPIOs for SPI and I2C TPM only if the corresponding
Kconfig options are set.
BUG=b:36265511
TEST=Verified on a reworked board that I2C TPM communication works
fine.
Change-Id: I3b293b8d410a6973a6dfea393c17d0be425b6a28
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update GPIO table to match the schematics for next build.
Change-Id: I949a14bfaa7972f2257a0b11ee81dcb0771e2f7f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Haswell, Broadwell, Baytrail, and Braswell ChromeOS devices'
FADT version were incorrectly set to 3, rather than the correct
ACPI_FADT_REV_ACPI_3_0. The incorrect value resulted in these
devices reporting compliance to ACPI 2.0, rather than ACPI 3.0.
This mirrors similar recent changes to SKL and APL SoCs.
Test: boot any affected device and check ACPI version reported
vai FADT header using OS-appropriate tools.
Change-Id: I689d2f848f4b8e5750742ea07f31162ee36ff64d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19498
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Correct the default GBB_HWID to "ROWAN TEST 9387"
BRANCH=chromeos-2016.05
BUG=b:35774871
TEST=emerge-rowan coreboot chromeos-bootimage,
strings /build/rowan/firmware/image.bin | grep "ROWAN TEST"
and look for 9387 in output
Change-Id: I7851010305caf056958c8a6a328b0506bf2208cd
Signed-off-by: Patrick Berny <pberny@chromium.org>
Reviewed-on: https://review.coreboot.org/19488
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=b:37712455
Change-Id: I3209aaef774712edab5e9f656ee84bfb6917b1c1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19472
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
BUG=b:37712790
Change-Id: I7764b4ec55b0beea82eeb6c379ef38ceeb1fb04e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19471
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable separate MRC cache for recovery mode. This requires change in
flash layout to accomodate another region for RECOVERY_MRC_CACHE.
BUG=b:37682566
TEST=Verified following scenarios:
1. Boot into recovery does not destroy normal mode MRC cache.
2. Once recovery MRC cache is populated, all future boots in recovery
mode re-use data from the cache.
3. Forcing recovery mode to retrain memory causes normal mode to retrain
memory as well.
Change-Id: I4c748a316436001c5a33754084ab4a74243e21df
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19457
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:35647967
TEST=boot from bob
Change-Id: I756513f02ac13e159d5b8b1ac2346fa42cf3c219
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cf18ed7b8fdf11594f812e5c48a2bd0fde5cb820
Original-Change-Id: I50c053ab7a6f6c14daee4fb2ab1cdcaeee2d67da
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452286
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19434
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
SD card detect pins should normally have a pull-up. It seems that for
micro-SD cards this doesn't really matter all that much, but for the
full-size slots we have on some Oak-derivatives (like Hana) it does.
BRANCH=oak
BUG=b:35854317
TEST=Booted Hana, confirmed that card detect no longer seemed stuck-on.
Booted Elm and confirmed that SD card behavior didn't change.
Change-Id: I9b20e0f6fe310e724d191e36ca0a81ab4fe5f593
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c2781eeef50f52c6f02ee9344274ddf4dcb0a946
Original-Change-Id: I428ac92efb07f94265673b04e0e0dd452649b9fd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/452861
Original-Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-on: https://review.coreboot.org/19432
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The new touchpad firmware uses i2c-hid instead of custom reporting
protocol. The touchpad also exposed another slave address (0x1e) for
kernel to communicate with the touchpad EC.
Change-Id: Iecaf14f7b8aed836120569e9ade9c3115bc00264
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/19461
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
In order for PD charge events to properly notify the OS when a charger is
attached we need to enable the PD MCU device and event source from the EC.
Without this change the charging still happens, but the OS does not notice
and update the charge state icon in the Chrome OS UI.
BUG=b:35586577
BRANCH=none
TEST=On a poppy board that has the VBUS rework applied, plug in a charger to
either port and see charge status updated to indicate charging in the
power_supply_info tool and the Chrome OS UI.
Change-Id: I59dcfc1cb5d11841f56cac7f4ffe461c2f9ec52a
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/19441
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
BUG=b:37684299, b:35775024
BRANCH=None
TEST=reboot and ensure graphics are displayed through
HDMI port.
Change-Id: I74a664b2d42f55adfa64f292f6ede4c956e16fbf
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19451
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:37486021
BRANCH=None
TEST=compile coreboot and make sure sda and sdb show
up in /sys/class/block.
Change-Id: I11344a4a5fc7e5b5d907d25439f92744a5fb70da
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19450
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the safety considerations, we should make sure the slot of SD is
enabled first, since we want to the power switch of corresponding is
powered up.
The different boards have the different power switch for sdmmc.
Some power switch IC need turn on delay for long time.
let's move the slot power of SD to romstage and avoid explicit delays
or per-board.
BRANCH=none
BUG=b:35813418, b:35573103
TEST=check the signal for children of gru, and boot up from sd card.
Change-Id: Id164e4c4c900c6b1ca0251fc27db4cd36c56f6ff
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ea1b01cc13628033b85251dbb44407f075efdc85
Original-Change-Id: I48ab543143d3de9be46608fc12d78e09decf8d79
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/447076
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19430
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Unlike other oak derivatives, Rowan uses an 8-lane BOE tv097qxm-nu0
MIPI/DSI panel that requires dual DSI support.
Rework oak display initialization to special case Rowan, which uses a
provided edid struct for its panel, special panel backlight sequencing
and needs to configure mtk_ddp and mtk_dsi to use dual dsi mode.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: I136ba5bd1ab12c4ad92995e066fc6d6cf54d0898
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19389
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This helper function was introduced so that mainboards don't need
to manually fill in these struct edid fields.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Ic9404a786a28b314b710e037dcae776be4b584ca
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19388
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: If66a2a1d461a411e112589c84a434066d48b9399
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19410
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ia1eacd15e71a46a37457ee2f117b156393c3393d
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19409
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ic69add8a3ce35be64fb37db4ed40163f6144fc9c
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19408
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ifeb09a0a35bff7cd9091f6d027f0065288ca35c9
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Utilize the intel/common code for tis_plat_irq_status() to remove
dependencies and code duplication on for bringing up a board
requiring tis_plat_irq_status().
Change-Id: I2aaa1d7d3ce171dc1788438ff9990fce533deb6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19371
Tested-by: build bot (Jenkins)
|
|
The CR50 TPM can do both SPI and I2C communication. However,
there's situations where policy needs to be applied for CR50
generically regardless of the I/O transport. Therefore add
MAINBOARD_HAS_TPM_CR50 to encompass that. Additionally,
once the mainboard has selected CR50 TPM automatically select
MAINBOARD_HAS_TPM2 since CR50 TPM is TPM 2.0.
Change-Id: I878f9b9dc99cfb0252d6fef7fc020fa3d391fcec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19370
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Lid switch is not available.
Hence report lid state as always open.
Change-Id: Ia9c82c3ad323912bad51cf55ed80a37b3110b1ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19219
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Configure PCI root port as per schematic.
Change-Id: I10ef682e8c54e22f328db5105d4da39c72ac2bed
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19390
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Read DRAM SPD and populate MemorySpdPtr fields
in UPD data structure for FSP.
BUG=b:36490168, b:35775024
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/fizz -x -a
We are currently working on bringup and have no
hardware to test on yet.
Change-Id: I191cc6bf1fd8aa461855c538b48fd39e3ffd7848
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19205
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static and empty ASL file.
Delete src/drivers/pc80/tpm/acpi/tpm.asl.
Change-Id: I6163e6d59c53117ecbbbb0a6838101abb468de36
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This commit changes the interrupt configuration for the touchpad to be
level triggered so it matches what the device is actually using.
When the system wakes from suspend by way of touchpad interrupt, or
there is touchpad input while in suspend that does not wake the device
(when the device is in tablet mode) the interrupt edge is not seen by
the AP so the driver does not handle the event and the touchpad keeps
the interrupt asserted and does not send further interrupts. The end
result is a non-functional touchpad after resume until it is reset or
the driver is reloaded.
This happens because the touchpad is actually treating the interrupt as
level triggered and expects the kernel driver to read a data packet over
I2C before it will de-assert the pending interrupt.
BUG=b:35774857
BRANCH=none
TEST=Test that the system can reliably wake from suspend by touchpad
event via the EC and continue to have a functional touchpad after resume.
Change-Id: Iaf7c04d9bc9d945bdcc196dff54c92a2a68368f3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19382
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Kevin's center logic isn't super clean so it needs 925 mV for center
logic. All newer gru variants only need 900 mV.
BRANCH=gru
BUG=b:37429075
TEST=Reboot tests
Change-Id: I8c3bd6c245700b23c27cd5758c35c9993f801cb4
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/479463
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19357
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It seems that we should only ever run at 900mV on center logic.
Changing it to 950mV before might have just masked over problems that
are now fixed.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=on kevin, run
stressapptest -M 1536 -s 1000
Change-Id: I5a09b1b403df800396bb2f2e8c76d14a4519d44a
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/391032
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Commit-Queue: Lin Huang <hl@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Create Soraka board which derives from Poppy, a KBL reference board.
More Soraka specific changes need to be done later on.
BRANCH=master
BUG=b:36995255
TEST=Build (as initial setup)
Change-Id: I8af68d2cf475df56336aa0e3bebe86a54ece1999
Signed-off-by: YH Lin <yueherngl@chromium.org>
Reviewed-on: https://review.coreboot.org/19343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move current NHLT configuration implementation to baseboard so that
variants can leverage it or provide their own configuration.
BUG=b:37375693
Change-Id: I2a4317c112f9e3614bd01eb6809727b73328d29d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure that
required SPD hex files are included in the SPD binary.
BUG=b:37375693
Change-Id: Ic9bcc03d5a35bebd14061680f264ac072b3c0634
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19325
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for ChromeOS GPIO ACPI table information by providing weak
implementation from the baseboard.
BUG=b:37375693
Change-Id: I641afe6bb45f106ddebde081a8ac2c64278ebeb9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide APIs for board_id() and gpio table functionality. Default weak
implementations are provided from the baseboard.
BUG=b:37375693
Change-Id: Ic3c946e6cb12b3c8ef3e83a1037ed0fc8cffbded
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19323
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to be able to share code across different poppy variants,
provide the concept of baseboard and variants. New directory layout:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/poppy - code
variants/poppy/include/variant - headers
New boards would then add themselves under their board name within
"variants" directory.
This is purely an organizational change.
BUG=b:37375693
Change-Id: If6c1c5f479cfffe768abf27495d379744104e2dc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19322
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up Kconfig file in order to support variants for poppy. Add
BOARD_GOOGLE_BASEBOARD_POPPY that can be set by various poppy variants
to use the common baseboard configs.
BUG=b:37375693
Change-Id: I399ecc8c3efb3af26e1fcf60fe2c75b24769fc0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19321
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add camera related support
* Enable the SA Imaging Unit and CIO2 devices.
* Enable TPS68470 PMIC and populate related ACPI objects.
* Enable OV cameras and populate related ACPI objects.
* Enable Dongwoon AF DAC and populate related ACPI objects.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that ACPI tables
have the required entries for all the camera devices.
Change-Id: Ifbe878bb6b25fc976e935fee16c4d59fadd47fe2
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18969
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch includes ipu.asl file in the main DSDT definition
to add ACPI entries for IMGU and CIO2 devices.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: Ib7485315cb9468da7c6aa090862657a265121493
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19110
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
1. Update formatting of gpio table to fit everything within 80 column
limit.
2. PEN_RESET gpio is non-existent. Get rid of it.
BUG=b:37375693
Change-Id: I1bcc4168659f365547e5f7227df8659e4bc7f243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19320
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable lower power state when running on battery. Deep S3 is not
enabled when in AC mode to support standard "docked" config.
BUG=b:36087058,b:36723679
TEST=Verified following behavior with USB mouse:
1. If AC is connected when entering S3, USB mouse is able to wake up.
2. If AC is not connected when entering S3, USB mouse does not wake up.
3. If AC is connected when entering S3 and removed after entering S3,
USB mouse does not wake up.
4. If AC is not connected when entering S3 and attached after entering
S3, USB mouse does not wake up.
Change-Id: I141a8d4779de004e27fcd9357cef787a38a27b24
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19276
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The HDA verb for falco/wolf's internal mic was wrong, preventing the mic
from working properly in Windows and macOS (the Linux driver overrides
the verb table, so wasn't affected). Set the verb connector/jack bits
properly, to no connector / no jack detect, in order to fix.
Also, make (2) small non-functional fixes:
On falco, NID 0x1A was being disabled twice (instead of 0x1A and 0x1B
both being disabled - copy/paste error).
On wolf, NID 0x19 was set to an internal analog mic, where it should have
been disabled (again, copy/paste error).
Both these errors were introduced when consolidating/upstreaming
and were not present in the original Chromium sources.
Test: boot Windows [8/8.1/10] and verify mic functional with Realtek
drivers on both falco and wolf.
Change-Id: I9c343dda4762f0b1f814318c155e22c59d2da8db
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the 'probed' setting from the Realtek 5663 headset codec I2C
device. This was added when we had a hardware issue that was preventing
I2C operation because the clock/data lines were swapped.
With new and/or reworked hardware this is no longer a problem and we do
not want the I2C layer in the kernel to talk to the device before the
rt5663 driver.
BUG=b:35585307
BRANCH=none
TEST=Boot on Eve and verify rt5663 driver still loads properly.
Change-Id: Ice38889e8f5d3fd1307056cab10fbe3f4e197749
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19304
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- remove old, buggy NGI code from falco/peppy variants
- remove superfluous INTEL_DP/INTEL_DDI configs, since already
selected by northbridge/haswell
- always use libgfxinit when use native init config selected
- enable NGI/libgfxinit for all slippy variants
The reset of the old Haswell NGI code will be cleaned up in
a subsequent patchset.
Test: select MAINBOARD_DO_NATIVE_VGA_INIT, observe panel init
using SeaBIOS and Tianocore payloads on peppy, wolf variants
Change-Id: Id5727cad7f714ffa57e77e2a25505e3c28f55237
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18824
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove the ACPI ALS device from the EC configuration because this system
has an ALS that is presented through the new EC sensor interface rather
than the legacy ACPI interface.
BUG=b:37179776
BRANCH=none
TEST=Boot an Eve device and ensure that 'acpi-als' device is not present
in /sys/bus/iio/devices.
Change-Id: Ie18b8a661e4d16464784ca8a227586036e7631de
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19265
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set UART0 to "PchSerialIoSkipInit" so the pins for this device are not
set back to native mode by FSP when configured as GPIO input by coreboot.
Now that FSP is not touching the pins I also removed the workaround to
reconfigure the pins after FSP.
BUG=b:35647877
BRANCH=none
TEST=Verify that GPP_C8-GPP_C11 are configured as GPIO input once the OS
is booted and they are not set back to native function by FSP.
Change-Id: Ifec4fa3e66ceeb660bad00c66bc7bd44bb457a01
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19264
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These lines act as inputs to both EC and AP and when the corresponding
TCPC mux is in low power mode the line is floating. Add an internal
pull-down to each GPIO to prevent it from floating in this state.
BUG=b:35775012
BRANCH=none
TEST=Verify that the kernel does not see a device present on DP when
the TCPC mux is in low power mode.
Change-Id: Ie229f84871e9994467c0ab660cc7e271a51d9cbb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19263
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This configures GPIO_177 as native function.
This enables OS to boot from sdcard.
BUG=b:35648535
TEST=Check OS boot from sdcard.
Change-Id: I73901d4a1b39752cbc452f3286d494587dac95d4
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18948
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:35586513
BRANCH=reef
TEST=Verified that touchscreen works on power-on and suspend/resume
on snappy.
Change-Id: I8418e742a69a2d6395baa2799a4da42a9bb5b312
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/19245
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order to support a standard "docked" config disable Deep S3 when
connected to AC power. This allows USB devices to wake the device
from suspend if it is externally powered, but still retains the
lower power state when running on battery.
BUG=b:36723679
BRANCH=none
TEST=manual testing on Eve for USB wake behavior:
1) when suspended on battery USB keyboard does not wake
2) when suspended while connected to AC a USB keyboard does wake
3) if suspended with AC, and then AC is removed, system does not
wake with USB keyboard
4) if suspended without AC, and then AC is added, system does not
wake with USB keyboard (it cannot get enabled without waking and
re-suspending)
Change-Id: I670e39d42cdb5b80612206da899be82ef3b2cbf2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19240
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the Intel WiFi SAR feature for Eve, which will be used to
provide wifi power tables based on values read from VPD.
This is enabled based on CONFIG_CHROMEOS because it relies on the
presence of VPD code from vendorcode/google/chromeos.
BUG=b:36727652
BRANCH=none
TEST=test on Eve by setting "wifi_sar" in VPD and ensuring that
the ACPI WIFI device gets the expected "WRDS" and "EWRD" tables
with the values that were set in VPD.
Change-Id: I11c129baca891221177575108ac09ba1707b516e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19241
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled
in both DC and AC states. However since using Deep S3 disables some
expected features like wake-on-USB it is not always desired to enable the
same state in both modes.
To address this split the setting and add a separate config for Deep Sx in
AC and DC states.
All motherboards that set this config were updated, but there is no actual
change in behavior in this commit.
BUG=b:36723679
BRANCH=none
TEST=This commit has no runtime visible changes, I verified on Eve that the
Deep SX config registers are unchanged, and it compiles for all affected boards.
Change-Id: I590f145847785b5a7687f235304e988888fcea8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19239
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
These lines act as inputs to both EC and AP. Thus, add internal
pull-downs to prevent them from floating.
BUG=b:35648530
Change-Id: I42326c810775d5449e99e52e81870970247ce335
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19243
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Put all configs required for enabling cr50 SPI TPM on poppy under
POPPY_USE_SPI_TPM so that it can be enabled any time for testing SPI
TPM on this board.
Also, add required callback for irq status and devicetree config for
GSPI0.
BUG=b:36873582
Change-Id: I67793093c006c1325fc16f669a96126525f83243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19238
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Scarlet don't have eDP and MIPI driver is not ready, skipping
display for now or else Scarlet would be stuck in
reading eDP HPD because there even not power for it.
TEST=boot to kernel on Scarlet
Change-Id: I02ab4ef21bf77b98414f537aca57b46c11922348
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19237
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Due to issues with stability limit the SKU with K4EBE304EB-EGCF
memory to 1600MHz instead of 1866MHz.
BUG=b:37172778
BRANCH=none
TEST=pass stress testing on devices with this memory
Change-Id: I02af7e9c35e2c5b0b85223d58025cbd29841d973
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19227
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update the I2C rise/fall timings based on newly measured values
on a new board with updated pull-up resistor values.
Touchscreen: rise time 98ns, fall time 38ms
Touchpad: rise time 111ns, fall time 41ns
TPM: rise time 112ns, fall time 34ns
BUG=b:35583133
BRANCH=none
TEST=Each I2C bus frequency was verified on a scope to be ~400MHz
Change-Id: Ibb3a15fa0cc862f36c1b9c63ac7847221020c4c0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19202
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some renamings force us to update our code:
* Scan_Ports() moved into a new package Display_Probing.
* Ports Digital[123] are called HDMI[123] now (finally!).
* `Configs_Type` became `Pipe_Configs`, `Config_Index` `Pipe_Index`.
Other noteworthy changes in libgfxinit:
* libgfxinit now knows about ports that share pins (e.g. HDMI1 and
DP1) and refuses to enable any of them if both are connected
(which is physically possible on certain ThinkPad docks).
* Major refactoring of the high-level GMA code.
Change-Id: I0ac376c6a3da997fa4a23054198819ca664b8bf0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/18770
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:35583511
TEST=check i2c bus 0 initializes from ap console log
Change-Id: Ibb6709159f5ed28ad0b62397d2ddb504dec55167
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19105
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Even though the i2c spec has no minimum data hold time in fast
mode the trackpad vendor indicates 300ns is their minimum. However,
the topology of the board uses FET isolation to cross voltage
domains. Therefore, the default 300ns which should work isn't reflected
on the device side of the voltage isolation circuit. Therefore,
increase the data hold time to show an observed data hold time of
more than 300ns on the device side.
BUG=b:36469182
Change-Id: I1b70f2f53c5a29cc7cfd5035a71ca5811b3bcba0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19065
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SD card detect pin is moved to GPP_E15 in the next build. Update
device tree and gpio config accordingly.
BUG=b:36012095
Change-Id: Ic0ff72cdcb0f1ca27abc7eb8da9ccd8a21b28522
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19107
Tested-by: build bot (Jenkins)
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.corp-partner.google.com>
|
|
Wake On Voice stream capture configuration is mono. It is sufficient
to keep DMIC_CLK_A1 on in S0ix; so, turning off DMIC_CLK_B1.
Power saving should be visible in the boards which has more
than one DMIC connected.
BUG=None
BRANCH=None
TEST=WoV and quad channel DMIC capture works
Change-Id: Ic46d4c7b30b945eba47a05d78386f48e4a675a03
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/19018
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Tested-by: build bot (Jenkins)
|
|
This patch attempts to finish the separation between CONFIG_VBOOT and
CONFIG_CHROMEOS by moving the remaining options and code (including
image generation code for things like FWID and GBB flags, which are
intrinsic to vboot itself) from src/vendorcode/google/chromeos to
src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig
options, and clean up menuconfig visibility for them (i.e. some options
were visible even though they were tied to the hardware while others
were invisible even though it might make sense to change them).
CQ-DEPEND=CL:459088
Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18984
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This callback was only required for a single mainboard, and it can
easily be moved to mainboard-specific code. This patch removes it from
the global namespace and isolates it to the Jecht board. (This makes
it easier to separate vboot and chromeos code in a later patch.)
Change-Id: I9cf67a75a052d1c86eda0393b6a9fbbe255fedf8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18981
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The virtualized developer switch was invented five years ago and has
been used on every vboot system ever since. We shouldn't need to specify
it again and again for every new board. This patch flips the Kconfig
logic around and replaces CONFIG_VIRTUAL_DEV_SWITCH with
CONFIG_PHYSICAL_DEV_SWITCH, so that only a few ancient boards need to
set it and it fits better with CONFIG_PHYSICAL_REC_SWITCH. (Also set the
latter for Lumpy which seems to have been omitted incorrectly, and hide
it from menuconfig since it's a hardware parameter that shouldn't be
configurable.)
Since almost all our developer switches are virtual, it doesn't make
sense for every board to pass a non-existent or non-functional developer
mode switch in the coreboot tables, so let's get rid of that. It's also
dangerously confusing for many boards to define a get_developer_mode()
function that reads an actual pin (often from a debug header) which will
not be honored by coreboot because CONFIG_PHYSICAL_DEV_SWITCH isn't set.
Therefore, this patch removes all those non-functional instances of that
function. In the future, either the board has a physical dev switch and
must define it, or it doesn't and must not.
In a similar sense (and since I'm touching so many board configs
anyway), it's annoying that we have to keep selecting EC_SOFTWARE_SYNC.
Instead, it should just be assumed by default whenever a Chrome EC is
present in the system. This way, it can also still be overridden by
menuconfig.
CQ-DEPEND=CL:459701
Change-Id: If9cbaa7df530580a97f00ef238e3d9a8a86a4a7f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18980
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
VBOOT_DYNAMIC_WORK_BUFFER and VBOOT_STARTS_IN_ROMSTAGE are equivalent in
practice. We can't have a dynamic work buffer unless we start in/after
romstage, and there'd be no reason to go with a static buffer if we do.
Let's get rid of one extra option and merge the two.
Change-Id: I3f953c8d2a8dcb3f65b07f548184d6dd0eb688fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18979
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some Chrome OS boards previously didn't have a hardcoded vboot
configuration (e.g. STARTS_IN_BOOTBLOCK/_ROMSTAGE, SEPARATE_VERSTAGE,
etc.) selected from their SoC and mainboard Kconfig files, and instead
relied on the Chrome OS build system to pass in those options
separately. Since there is usually only one "best" vboot configuration
for a certain board and there is often board or SoC code specifically
written with that configuration in mind (e.g. memlayout), these options
should not be adjustable in menuconfig and instead always get selected
by board and SoC Makefiles (as opposed to some external build system).
(Removing MAINBOARD_HAS_CHROMEOS from Urara because vboot support for
Pistachio/MIPS was never finished. Trying to enable even post-romstage
vboot leads to weird compiler errors that I don't want to track down
now. Let's stop pretending this board has working Chrome OS support
because it never did.)
Change-Id: Ibddf413568630f2e5d6e286b9eca6378d7170104
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19022
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of defining a separate LID device for mainboards using
chromeec, define EC_ENABLE_LID_SWITCH for these boards.
Change-Id: Iac58847c2055fa27c19d02b2dbda6813d6dec3ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18964
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of defining SIO_EC_ENABLE_PS2K by default for all boards and
doing an undef in variant/onboard.h, move the definition of
SIO_EC_ENABLE_PS2K to variant/onboard.h. This avoids dependency
between different *.asl files.
Change-Id: I83e4ce42a594e952a443c618d7ef9840113027b9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18965
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Remove CPU throttling effect of the charger sensor
Refers Change-Id I267b6e07fa9def2c91ff9f6035f2d9437faf1965
(mb/google/reef: Remove CPU throttling effect of the charger sensor)
to remove CPU throttling effect of the charger sensor
since it's not relevant to throttle CPU based on the charger sensor.
2. Change TSR1 influence from 200 to 100
3. Change TSR2 sample period from 120s to 30s
BUG=b:35585781
BRANCH=reef
TEST=built, and verified on snappy by thermal team.
Change-Id: Ic3fc51c4288b24f4e64950e5b148aed4495a1c3b
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18950
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
BUG=b:35775024
BRANCH=None
TEST=Compiles successfully
Change-Id: I92cf9baa4c3aefc6983511543d875e74a6b0bf94
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/18944
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Transfer the gpio assignments in the fizz schematic
into gpio.h.
BUG=b:35775024
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/fizz -x -a
Change-Id: If05aa2859f2511c3f616dc3fb38bca4fb8524697
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/18797
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
- Remove spd files/directory
- Remove audio blobs
- Remove dptf.asl contents
- Remove MKBP
- Remove acpi table initialization
BUG=b:35775024
BRANCH=None
TEST=Compiles successfully
Change-Id: I5d717d23224956ee1653c5ded28abd05cd254c3a
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/18857
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Creating google/fizz directory based on poppy (using kabylake and FSP
2.0). Only making name changes and Copyright year changes. Many
poppy-specific configs left in and will be updated in follup CLs.
BUG=b:35775024
BRANCH=None
TEST=Compile fizz board
Change-Id: Icab3639a53fef65e904e797028916fda879fff7c
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/18796
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Create the initial Nasher variant which refers to the Reef.
Nasher is APL board that derives from reference board Reef.
BRANCH=master
BUG=b:36389286
TEST=Build (as initial setup)
Signed-off-by: YH Lin <yueherngl@chromium.org>
Change-Id: I7962aa8246890149988c7f02dcd90d820df7b901
Reviewed-on: https://review.coreboot.org/18928
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. correct DPTF TCHG target device to TSR2
2. Refers Change-Id I267b6e07fa9def2c91ff9f6035f2d9437faf1965
(mb/google/reef: Remove CPU throttling effect of the charger sensor)
to remove CPU throttling effect of the charger sensor
since it's not relevant to throttle CPU based on the charger sensor.
BUG=b:35586881
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I4801e0e612e0ddf90764ffe080c679818d33212a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18920
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since SD card controller is expected to enter D3hot by runtime power
management if there is no card inserted, we need to use a sideband IRQ
pin which is not under the control of the controller. Thus, configure
GPP_A7 as the sideband IRQ pin and pass it to OS as the card detect
pin.
BUG=b:35586693
BRANCH=None
TEST=Verified on a reworked poppy board that card detect works fine.
Change-Id: I4512f5d7829583e27c9750463396eaffbc5702b4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18926
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We just support Raydium touchscreen instead of Elan.
Thus we have to remove Elan touchscreen device
and add Raydium touchsrcreen device.
BUG=b:35775065
BRANCH=reef
TEST=emerge-sand coreboot
Change-Id: I7b33a29287dcb90e379b52cc93825f2988a0d3c9
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/18789
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change hid name to "WDHT0002" for Weida WDT8752 which is supported by
standard hid i2c Linux driver.
BUG=b:35586513
BRANCH=reef
TEST=build, boot on snappy, and verified acpi node "WDHT0002" created.
Change-Id: Ie0cc980aa427b6db1eb14eb7868718619bb1310f
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18874
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
It's not relevant to throttle CPU based on the charger sensor.
So, remove this CPU throttling effect.
BUG=b:35908799
BRANCH=master
TEST=Built and booted on Electro DUT
Change-Id: I267b6e07fa9def2c91ff9f6035f2d9437faf1965
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18852
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
We have code for certain Veyron variant names that were either never
made into an actual board (Gus, Nicky, Thea) or used for Google-internal
test boards that no longer exist (Pinky, Shark). Let's clean them out to
avoid confusing people.
Change-Id: Icdce5f0f3613e089d0994318b02dba54170f0c42
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18860
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
With a recent patch (google/veyron_*: Add new Micron and Hynix modules)
we switched RAM codes for Veyron boards to tri-state since we were
running out of binary numbers. Unfortunately we only tested that change
on Minnie and Speedy, and it turns out that it broke Jaq, Jerry and
Mighty. The "high" RAM code pins on those boards were incorrectly
strapped with 100Kohm resistors (as opposed to 1Kohm on Minnie and
Speedy), which is too high to overpower the SoC-internal pull-down we
use to differentiate "high" from "tri-state". Since we already used
tri-state codes on some Minnie and Speedy SKUs we have to hack up the
code to work differently on these two groups of boards to keep
everything working.
BRANCH=veyron
BUG=b:36279493
TEST=Compiled, confirmed ram_code called the right function depending on
board.
Change-Id: I253b213ef7ca621ce47a7a55a5119a167d944078
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18859
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Now that EC on poppy is stable, it is time to switch on EC SW sync.
BUG=b:36178824
BRANCH=None
TEST=Verified that EC SW sync is done properly and device boots to OS.
Change-Id: I1395ad8af73128a8dd220351f5b5da157659b19e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18838
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The kernel driver for rt5663 expects to get an interrupt on both
a rising and falling edge, and using a legacy interrupt doesn't
provide that flexibility.
Instead configure this pin as a GPIO and use the interrupt through
the GPIO controller. This allows using GpioInt() with ActiveBoth
setting and results in correct operation of the headset jack.
This is a clone of Duncan's patch for eve
at I6f181ec560fe9d34efc023ef6e78e33cb0b4c529
BUG=none
BRANCH=none
TEST=test on poppy that headset jack detect is read properly at
boot, and that plugging in and removing both generate a single
interrupt event in the driver.
Change-Id: I4aaa4164cb277a98ab5d5f033632f5e16bfb779e
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18853
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The kernel driver for rt5663 expects to get an interrupt on both
a rising and falling edge, and using a legacy interrupt doesn't
provide that flexibility.
Instead configure this pin as a GPIO and use the interrupt through
the GPIO controller. This allows using GpioInt() with ActiveBoth
setting and results in correct operation of the headset jack.
BUG=b:35585307
BRANCH=none
TEST=test on Eve that headset jack detect is read properly at
boot, and that plugging in and removing both generate a single
interrupt event in the driver.
Change-Id: I6f181ec560fe9d34efc023ef6e78e33cb0b4c529
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18836
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update the DPTF parameters based on thermal test result.
(ZHT_DPTF_DVT_v0.6_20170314.xlsx)
1. Increase PL2 Max to 15W.
BUG=b:35583586
BRANCH=reef
TEST=build and verify PL2 Max value on electro dut
Change-Id: I13167e28267d5827d79a6bde31f077a01f2bd535
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18807
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Keep the BOOT0 pin triggering the MCU bootloader as an input,
so the Servo debug board doesn't have to fight with the PCH to program
it, the net already has an external pull-down to ensure that the MCU is
in normal mode at boot.
By default, do not drive the FP sensor reset from the PCH, the MCU is
now managing the reset line (but the PCH still has a connection on the
current boards).
BRANCH=none
BUG=b:36025702
TEST=manual testing, program the MCU through a Servo v2 board, and use
the FP sensor through the MCU and verify it is not stuck under reset.
Change-Id: I19113b5d78013d0ab6ec5a72c6f71dd4c67a88e8
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/18830
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set the AC and DC loadline values based on the KBL-Y 2+2 defaults
that are applied by FSP. These will be tuned later and are exposed
as defaults so the engineers know what to start with.
BUG=b:36228330
BRANCH=none
TEST=Build and boot on Eve and check debug FSP output to ensure that
it is applying the provided loadline values
Change-Id: Ieae4f2b201d8210e75bdb9438070a3a2e1fda6b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18820
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
With the move to FSP 2.0 the number of VR types supported was
reduced to 4, and the VR_RING type is no longer present.
This means all existing boards using FSP 2.0 are incorrectly
passing VR configuration into FSP as the values corresponding to
"GT Sliced" and "GT Unsliced" have changed.
Fix this by updating the skylake SOC VR handling to account for
changes in the FSP configuration and no longer provide VR_RING
type when using FSP 2.0.
BUG=b:36228330
BRANCH=none
TEST=manual: build and boot on Eve
Change-Id: I59eea9fba006a4c235d7b42d07fdc6e4f44f7351
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
On this platform the DMICs are connected to the rt5514 DSP instead
of directly connected to the SOC. Use the new rt5514 NHLT blob
instead of the 4ch DMIC blob and add the required I2C and SPI
entries in devicetree so this can get probed properly.
BUG=b:35585307
BRANCH=none
TEST=build and boot on Eve P1 and check for rt5514 driver enumerated
by the kernel
Change-Id: I0f2cb532771ee1857df7f33c52a96acf96dc1f54
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18817
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add FPF_STATUS region under MISC_RW. The purpose of the region is to
store FPF status.
Change-Id: I2997b3d39a94bf444df51068f254edcf49c47afd
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18773
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Sand is not convertible and no EC sensor sends event from EC to AP.
That event default is tablet mode, we don't have to enable tablet event.
Modify the ec.h, is based on <baseboard/ec.h>
BUG=b:36108742
BRANCH=reef
TEST=emerge-sand coreboot, boot to OS and touchpad and keyboard can work.
Change-Id: I6b6b45b5b4daf2c430ed18130f39eab0bd9a9812
Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com>
Reviewed-on: https://review.coreboot.org/18737
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
