summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2022-04-21tpm: Refactor TPM Kconfig dimensionsJes B. Klinke
Break TPM related Kconfig into the following dimensions: TPM transport support: config CRB_TPM config I2C_TPM config SPI_TPM config MEMORY_MAPPED_TPM (new) TPM brand, not defining any of these is valid, and result in "generic" support: config TPM_ATMEL (new) config TPM_GOOGLE (new) config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE) config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE) What protocol the TPM chip supports: config MAINBOARD_HAS_TPM1 config MAINBOARD_HAS_TPM2 What the user chooses to compile (restricted by the above): config NO_TPM config TPM1 config TPM2 The following Kconfigs will be replaced as indicated: config TPM_CR50 -> TPM_GOOGLE config MAINBOARD_HAS_CRB_TPM -> CRB_TPM config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE Signed-off-by: Jes B. Klinke <jbk@chromium.org> Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2022-04-21mb/google/dewatt: Set SPI speed to 100Mhz on board version 3Rob Barnes
After assessing the signal integrity, 100 MHz SPI fast speed can be enabled for SPI ROM. BUG=b:213403891 BRANCH=guybrush TEST=Build and boot to OS in Dewatt board version 3. Change-Id: If0318abf1fed9b1f4ba876f736fdbf92c1ea6933 Signed-off-by: Rob Barnes <robbarnes@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63747 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-21mb/google/dedede/var/kracko: Add FW_CONFIG probe for EXT_VRRobert Chen
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on kracko. BUG=b:223687184 TEST=emerge-dedede coreboot Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Change-Id: Ib12265591e679e6b9ed34299f1256db05147eaef Reviewed-on: https://review.coreboot.org/c/coreboot/+/63111 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-21mb/google/dedede/var/drawcia: Add FW_CONFIG probe for EXT_VRRobert Chen
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on drawcia. BUG=b:223687184 TEST=emerge-dedede coreboot Change-Id: I683049e9d2b10fc9455ef782ce798f1c453073bc Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63110 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-21mb/google/dedede/var/lantis: Add FW_CONFIG probe for EXT_VRRobert Chen
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on lantis. BUG=b:223687184 TEST=emerge-dedede coreboot Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Change-Id: I3d8eec1d2f962d42f3be225eef8498e8b722aace Reviewed-on: https://review.coreboot.org/c/coreboot/+/63112 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-21mb/google/nipperkin: Fix WLAN to GEN2 speedRob Barnes
Fix WLAN PCIE speed to GEN2. Dynamic switching between speeds is causing the PSP to hang when resuming from S0ix suspend. The root cause is still under investigation. Just disabling PSPP fixes the hang but causes poor PLT performance. BUG=b:228830362 BRANCH=guybrush TEST=suspend_stress_test on AC and DC Change-Id: I988365e51aca0d6515c5605b3032521cf59d8d30 Signed-off-by: Rob Barnes <robbarnes@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63722 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-21mb/google/brask/variants/moli: update overridetreeRaihow Shi
Add FW_CONFIG STORAGE and probe for UNKNOWN, NVME and eMMC. BUG=b:220039297 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: If83031edcd90ea746704590765102b9b0dee03c1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63080 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Zhuohao Lee <zhuohao@google.com>
2022-04-21mb/google/brya/var/taeko: Add WIFI SAR support for tarloJoey Peng
Taeko/Tarlo uses the WIFI_SAR_ID field in FW_CONFIG to pick which SAR table to load. BUG=b:226684990 TEST=emerge-brya coreboot Cq-Depend: chrome-internal:4676926, chrome-internal:4686953 Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com> Change-Id: I9852553f5c91494db845d45a94e2566248538bba Reviewed-on: https://review.coreboot.org/c/coreboot/+/63644 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-21mb/google/brya/var/osiris: Generate SPD ID for supported partsDavid Wu
Add supported memory parts in mem_parts_used.txt, and generate SPD id for these parts. MT53E512M32D1NP-046 WT:B (Micron) MT53E1G32D2NP-046 WT:B (Micron) H54G46CYRBX267 (Hynix) H54G56CYRBX247 (Hynix) K4U6E3S4AB-MGCL (Samsung) K4UBE3D4AB-MGCL (Samsung) BUG=None TEST=build pass Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I1fbdce203afd282cef9fcd7aebbace69d19fbbf1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63706 Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-21mb/google/brya: Create osiris variantDavid Wu
Create the osiris variant of the brya0 reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.5.0). BUG=b:229352299 BRANCH=None TEST=util/abuild/abuild -p none -t google/brya -x -a make sure the build includes GOOGLE_OSIRIS Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I41e088a3415add86cba87c919af23494f816bb24 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63650 Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-20mb/google/skyrim: Update SPI settings for skyrimChris.Wang
Update SPI setting as below: Normal speed:33mhz Fast speed:66mhz Alt speed:66mz TPM speed:33mhz BUG=b:225213679 TEST=boot skyrim and verify spi settings. Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com> Change-Id: Icbe4b9f4794f7e883c3819258ede809c3c8922b0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63717 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-04-20mb/google/brya/var/vell: increase RFI Spread Spectrum to 6%Robert Chen
Increase RFI Spread Spectrum to 6% for Vell as RF team request. The default of Spread Spectrum in FSP is 1.5%, and set 1.5% in baseboard as default. BUG=b:228929196 TEST=emerge-brya coreboot and pass RF test as before Change-Id: I7cdca8f51ad18f4ab03e4e6c744b60da68263ce2 Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63440 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-20mb/google/brya/var/brya0: configure gpio for headsetAmanda Huang
Configure GPP_R0, GPP_R1, GPP_R2 and GPP_R3 for headset function enable with ALC5682I+MAX98360. BUG=b:202671753 BRANCH=firmware-brya-14505.B TEST=emerge-brya coreboot Change-Id: I93070a8096d43557a50e5a545227f2906e299d8e Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63721 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
2022-04-20mb/google/brya/var/brya0: Swap TPM and touchscreen I2C busAmanda Huang
Based on the latest schematic, exchange I2C port for TPM/touchscreen. TPM: I2C3 -> I2C1 Touchscreen: I2C1 -> I2C3 BUG=b:202671753 TEST=emerge-brya coreboot Change-Id: Ifa6235869f34e0038a8ecad33d59654626cf7815 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63709 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-20Revert "mb/google/guybrush/var/dewatt: Override SPI fast speed"Rob Barnes
This reverts commit d80d88c0fec96b2fff93db87d0c83f4c6754ae7a. Reason for revert: 100Mhz should only be enabled on DeWatt on board version >=3. Enabling it on board version 2 will cause failures. BUG=b:213403891 BRANCH=guybrush TEST=Build dewatt Change-Id: I0b6acd2cda2af35ff33e89e3b339731e35d72cb1 Signed-off-by: Rob Barnes <robbarnes@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63746 Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-20ChromeEC boards: Drop `IGNORE_IASL_MISSING_DEPENDENCY`Angel Pons
This should no longer be needed because the ASL has been fixed. Change-Id: I4d1500217bef54fa3d2be397e5e2a155da3f965d Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63525 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-04-20mb/google/brya/var/redrix: Add alias back to RP6 WWAN deviceTim Wawrzynczak
This alias name is required for the mainboard.c code to generate the appropriate power-off seqeuence for use during orderly S5 shutdown from the OS. It had been accidentally removed, but is required, so this patch adds it. BUG=b:227788351 TEST=compile Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I8936a01bd3a6b908033a8c58bd4e84b30d199e98 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63556 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Subrata Banik <subratabanik@google.com>
2022-04-20mb/google/brya/var/anahera{4es}: Enable power saving for Smart CardWisley Chen
Configure the power saving pin for Smart Card. BUG=b:229356121 TEST=emerge-brya coreboot chromeos-bootimage Change-Id: Ia17970f717c6ba806d9603031c486bad86e42b37 Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63648 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-20mb/google/guybrush/var/dewatt: Override SPI fast speedKenneth Chan
After assessing the signal integrity, 100 MHz SPI fast speed can be enabled for SPI ROM. BUG=b:213403891 TEST=Build and boot to OS in Dewatt board version 2. Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Change-Id: I7301d873e36bec4ee46c9d18293f924500ea9aba Reviewed-on: https://review.coreboot.org/c/coreboot/+/63685 Reviewed-by: Rob Barnes <robbarnes@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-19mb/google/brya: Disable PCH USB2 phy power gating for felwinterSridhar Siricilla
The patch disables PCH USB2 Phy power gating to prevent possible display flicker issue for felwinter board. Please refer Intel doc#723158 for more information. BUG=b:221461379, b:226020977 TEST=Verify the build for felwinter board Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Change-Id: I25033ea218fa3154eb99af6be43c4198f4db3bcb Reviewed-on: https://review.coreboot.org/c/coreboot/+/63294 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2022-04-19mb/google/brask/variants/moli: update type-c setting in overridetreeRaihow Shi
Add conn1 for pch_espi and add type-c port2 for pmc_mux. BUG=b:220814038 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: Idfd7b761496a110f34838abb0fd408b37d390ba2 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63570 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-19mb/google/brask/variants/moli: add delay time to rtd3-coldRaihow Shi
This CL adds the delay time 50 ms and 20 ms into the RTD3 sequence, the reason is that the rise and fall times of each signal may differ by board, and so those board-specific delays must be taken into account when power sequencing. We checked power on sequence requires enable pin prior to reset pin, so added delay to meet the sequence. Based on BH799BB_Preliminary_DS_R079_20201124.pdf in chapter 7.2. BUG=b:228907551 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: Idecb1c89655c9b8b720c3c65efc77e06e6a8b300 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63544 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-19mb/google/brask/variants/moli: remove i2c1 in overridetreeRaihow Shi
Remove i2c1 because brask devicetree is already has it. BUG=b:220814038 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: Ic782e1c6434ac57bdf65b3d9f4219bdf32d25b9e Reviewed-on: https://review.coreboot.org/c/coreboot/+/63545 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-19mb/google/skyrim: Configure Pen Detect deviceIan Feng
Enable pen garage. Pen detect is active low. BUG=b:229168203 TEST:Build and boot to OS in skyrim. Evtest work as expected Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "PRP0001:00" Supported events: Event type 0 (EV_SYN) Event type 5 (EV_SW) Event code 15 (SW_PEN_INSERTED) state 1 Properties: Testing ... (interrupt to exit) Event: time 1649922170.578779, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0 Event: time 1649922170.578779, -------------- SYN_REPORT ------------ Event: time 1649922172.070740, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1 Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Change-Id: I3bb07af6aebdc355a73148d8be79b1014147f61d Reviewed-on: https://review.coreboot.org/c/coreboot/+/63633 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2022-04-19mb/google/skyrim: Add Goodix touchscreenIan Feng
Add Goodix touchscreen according to the Programming Guide Rev.0.7 BUG=b:228907558 TEST=local build and tested with Goodix touch screen Change-Id: I35dd3ca76e9e0f17508bef46c90b53b4be5d0033 Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63573 Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-19mb/google/brask: fix boot beepDtrain Hsu
Fix the issue that can't hear the boot beep at dev screen. GPP_B14 is used for PWM_PP3300_BUZZER and it should set to GPO. Modify GPP_B14 from PAD_CFG_NF_LOCK to PAD_CFG_GPO_LOCK. BUG=b:229345416 BRANCH=firmware-brya-14505.B TEST=emerge-brask coreboot and verify if the buzzer beeps. Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Change-Id: I601735ab20974cd992ca5dd6dbaca1517a395aa2 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63645 Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-19mb/google/brask/variants/moli: Pick VBT based on FW_CONFIGRaihow Shi
Pick specific VBTs for HDMI, DP, and ABSENT according to FW_CONFIG. BUG=b:220241277 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: Icc8fbef1467605505459fce264697f670591c81e Reviewed-on: https://review.coreboot.org/c/coreboot/+/63604 Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-19mb/google/brya/var/anahera{4es}: select DRIVERS_GENESYSLOGIC_GL9750Wisley Chen
select DRIVERS_GENESYSLOGIC_GL9750 to disable ASPM L0s. BUG=b:229213455 TEST=emerge-brya coreboot chromeos-bootimage Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com> Change-Id: Ie89fa6c66974284063cd25ae8097db94a93326ca Reviewed-on: https://review.coreboot.org/c/coreboot/+/63638 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-19mb/google/nissa: Add gpio lock pinsEric Lai
Followed the Brya series to lock the gpio pins in baseboard. Variant should honor locked gpios from baseboard, but not the last. Variant can add more gpios to lock if needed. BUG=b:216671701 TEST='emerge-nissa coreboot chromeos-bootimage', flash and verify that nivviks boots successfully to kernel. Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Change-Id: Ib34ca287596a6958407a944d0caf53f4bcc60d9b Reviewed-on: https://review.coreboot.org/c/coreboot/+/63568 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2022-04-19mb/google/brya: Add Kconfig for TPM I2C busRaihow Shi
Add TPM I2C for crota to avoid TPM I2C fail. BUG=b:229200525 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: I8054e623fb0c3c549c3373982ce9d4fbd57e0fd7 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63635 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-19mb/google/brya/var/crota: Kconfig: Select TPM I2C bus driverTerry Chen
Add TPM I2C for crota to avoid TPM I2C fail. BUG=b:226315394 TEST=USE="project_crota emerge-brya coreboot" and verify it builds without error. Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com> Change-Id: I7eb3ce6c2faf857c8f5d789af395e315caea4102 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63617 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-19mb/google/guybrush/var/dewatt: Update APU STT settingChris.Wang
update STT setting for dewatt. BUG=b:228040295 BRANCH=guybrush TEST=build, verify the parameter has been applied to the system by checking the AGT tool. Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com> Change-Id: Id319d42747dd0d5f6a9ca727635d85e6b9bd65af Reviewed-on: https://review.coreboot.org/c/coreboot/+/63699 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-04-18mb/google/guybrush: Remove EC_ENABLE_LID_SWITCHRob Barnes
Remove EC_ENABLE_LID_SWITCH since this causes a duplicate SW_LID entries. The other SW_LID entry is generated by MKBP. BUG=b:228907256 BRANCH=guybrush TEST=Lid open close triggers events on Nipperkin Change-Id: I5c1cf7aeac8405bce7bfc77110eceaf3e5383fe7 Signed-off-by: Rob Barnes <robbarnes@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63658 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Robert Zieba <robertzieba@google.com> Reviewed-by: Jon Murphy <jpmurphy@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2022-04-18mb/google/guybrush/var/nipperkin: turn off WLAN ASPM L1ssKevin Chiu
BUG=b:227296841 BRANCH=guybrush TEST=emerge-guybrush coreboot chromeos-bootimage pass PLT criteria: S0 > 600ms, s0i3 > 14 days Change-Id: I9c61e1d0f3db8b9885040255d6de266616768b68 Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63537 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Jon Murphy <jpmurphy@google.com>
2022-04-14mb/google/guybrush: Set BT USB to use GPIO for statusTim Van Patten
Set the BT USB device to use GPIO for the power status. This causes an ACPI `_STA()` function to be generated that returns the power status of the BT USB device, rather than always returning `0x1`. This `_STA()` function can be used during boot to skip enabling the device (and performing the associated sleep) if the device is already powered on. BRANCH=None BUG=b:225022810 TEST=Dump SSDT table for guybrush Signed-off-by: Tim Van Patten <timvp@google.com> Change-Id: I72f6b28671efddfbef53f328d904a05f73f39efa Reviewed-on: https://review.coreboot.org/c/coreboot/+/63559 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-04-14mb/google/skyrim: Inject SPDs into APCBKarthikeyan Ramasubramanian
Update the build scripts to inject variant specific SPDs into APCB. BUG=None TEST=Build and boot to OS in Skyrim boards with all the concerned memory parts. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: I3b3f6f248d54681c6f55c00660d1f2988ae906ba Reviewed-on: https://review.coreboot.org/c/coreboot/+/63600 Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-14mb/google/skyrim/var/skyrim: Add supported memory partsKarthikeyan Ramasubramanian
Add supported memory parts and generate the associated DRAM part ID. Also for MT62F2G32D8DR-031 WT:B memory part, add a custom SPD that configures the DRAM speed at 5500 MHz. Use this custom SPD until that part can operate at full speed (i.e. 6400 MHz). BUG=None TEST=Build Skyrim. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: Id87e79f5d6187d57d74487841c09aa309f1450b4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63599 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Robert Zieba <robertzieba@google.com> Reviewed-by: Jon Murphy <jpmurphy@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-04-14mb/google/brya/var/kano: Configure Acoustic noise mitigationDavid Wu
Setup the following acoustic noise mitigation features: 1) Slew rate for both IA and GT domains to 1/8 2) Disable Fast package C ramp BUG=b:229046516 TEST=build and verified by power team Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ifb5700391e33818878994f205acae7ee3b1b96d9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63610 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-14mb/google/nipperkin: Disable PSPP for WLANRob Barnes
Disable PSPP parameters for WLAN card on Nipperkin. This feature is causing S0ix resume hangs. BUG=b:227296841,b:228830362 BRANCH=guybrush TEST=Suspend stress test passes on Nipperkin Signed-off-by: Rob Barnes <robbarnes@google.com> Change-Id: I38f05b92ace4aba61163194a6a638915882b8871 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63593 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-14mb/google/brya: Add variant_init and variant_finalize callbacksTim Wawrzynczak
Some brya variants may need to initialize and finalize some variant-specific devices during ramstage, therefore add the commonly-used hooks and callbacks to support this. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: Iede6dc5a5b9a7385fedd59d4eeaaba118eff0e20 Reviewed-on: https://review.coreboot.org/c/coreboot/+/62382 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2022-04-13mb/google/guybrush/var/nipperkin: probe privacy screen device by fw_configKevin Chiu
BUG=b:228448327 BRANCH=guybrush TEST=emerge-guybrush coreboot chromeos-bootimage check ACPI device "LCD" in SSDT Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com> Change-Id: I42c5abdbe3bfab72016d56399278a7aff9e33377 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63575 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Rob Barnes <robbarnes@google.com>
2022-04-13mb/google/guybrush: Disable EN_SPKR on init on Nipperkin and DewattYu-Hsuan Hsu
We don't want to enable the speaker on init. It will be enabled while using GPIO AMP codec in depthcharge. BUG=b:223289882 TEST=boot Nipperkin and Dewatt and then verify the devbeep and gpio values in kernel Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com> Change-Id: Id874421d7464b15be6e521576696bb97e6b22d6a Reviewed-on: https://review.coreboot.org/c/coreboot/+/63540 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-04-13mb/google/brya/baseboard/nissa: Configure I2C lcnt and hcntReka Norman
Configure lcnt and hcnt directly to give the required frequency, tHIGH and tLOW, instead of using rise and fall times. Aim for a frequency of 390 kHz to make sure it doesn't exceed 400 kHz on different boards. BUG=b:227517802 TEST=Probe the clock line and check that it meets the requirements for frequency, tHIGH and tLOW. Change-Id: I4d4f877c1f0cd9aacd3fa152890b7ef82e059f78 Signed-off-by: Reka Norman <rekanorman@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63562 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-13mb/google/brya: Create craask variantTyler Wang
Create the craask variant of the brya0 reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.5.0.) BUG=b:None BRANCH=None TEST=util/abuild/abuild -p none -t google/brya -x -a make sure the build includes GOOGLE_CRAASK Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Change-Id: Icf03e3f18468d7dd207ab200fa2dcf96afd02f8b Reviewed-on: https://review.coreboot.org/c/coreboot/+/63256 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-13mb/google/brya: Add missing parameter name to variant_generate_s0ix_hookReka Norman
Fixes the following build error: src/mainboard/google/brya/mainboard.c: In function 'variant_generate_s0ix_hook': src/mainboard/google/brya/mainboard.c:157:40: error: parameter name omitted void __weak variant_generate_s0ix_hook(enum s0ix_entry) ^~~~~~~~~~~~~~~ BUG=None TEST=`abuild -a -x -c max -p none -t google/brya` now succeeds Change-Id: Id578766e2a3b7647e920740dde3e356a7db39d4d Signed-off-by: Reka Norman <rekanorman@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63564 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-13mb/google/brya/var/nereid: Enable OZ711LV2LN SD card controllerReka Norman
Select the Bayhub LV2 driver, and implement power sequencing as per the datasheet. BUG=b:223304542 TEST=Check that connecting an SD card works as expected in the OS. Probe the EN and RST signals and check the timing requirements are met. Change-Id: Id1cca2024e06e5b2c7cefd22aa0b735bc542dc3b Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63434 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org>
2022-04-13mb/google/brya/var/brya0: Change MAX98360 AMP interface to I2S1Amanda Huang
Based on the latest schematic, change MAX98360 AMP interface from I2S2 to I2S1 due to Intel BT offload concern. BUG=b:202671753 BRANCH=firmware-brya-14505.B TEST=dmidecode -t 11 Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com> Change-Id: I9ee45dbceabdedd39a9befffb8002b8bc3d4bfb4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63495 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-12mb/google/brya/var/vell: add WWAN power sequence setting for vellRobert Chen
Add WWAN power sequence setting to meet spec BUG=b:220084872 BRANCH=firmware-brya-14505.B TEST=emerge-brya coreboot Change-Id: If6d3f965b8f6b6753446f55a8bd47d3b0c1ae7be Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/61847 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-09mb/google,samsung: Drop init_bootmode_straps()Kyösti Mälkki
Change-Id: Idcaf30c622bf5dc0f1295f2639c656086d01ff7e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/59008 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2022-04-07mb/google/brya/var/taniks: Enable Genesys L1 max entry delayJoey Peng
The workaround causes the eMMC controller to not enter its L1 during the boot process BUG=b:220079865 TEST=Build FW and run stress exceed 2500 cycles. Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com> Change-Id: I2a5888e943c1ebf83a54f9b172f986f8b13d9b6a Reviewed-on: https://review.coreboot.org/c/coreboot/+/63131 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-07ChromeOS: Add DECLARE_x_CROS_GPIOS()Kyösti Mälkki
Change-Id: I88406fa1b54312616e6717af3d924436dc4ff1a6 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58899 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-07mb/google/dedede/var/beadrix: Update PCIe and SATA pins for low power ↵Teddy Shih
consumption To achieve low power consumption, we disable unused PCIe and SATA pins at beadrix/overridetree.cb according to baseboard/devicetree.cb and mainboard schematic. Original measured beadrix board's power consumption is about 250 mW. After we disable unused PCIe and SATA pins, as well as, enable the other low power MUX CL (3487086: USB MUX: Update low power mode of MUX anx7447 used as MUX only | https://chromium-review.googlesource.com/c/chromiumos/platform/ec/ +/3487086), the measured power consumption achieves about 110 ~ 116 mW, as well as, meets Google battery life for 14 days in the suspend state and Intel low power consumption about 116 mW. BRANCH=dedede BUG=b:204882915 TEST=on beadrix, measured power consumption meets Intel power consumption. Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com> Change-Id: I79ec524c5ce8f2a79da4aeba084786fb9dac17af Reviewed-on: https://review.coreboot.org/c/coreboot/+/62776 Reviewed-by: Teddy Shih <teddyshihau@gmail.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Ivan Chen <yulunchen@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-07mb/google/guybrush: allow MKBP devices and disable TBMC deviceKenneth Chan
Enable MKBP (Matrix Keyboard Protocol) interface for all guybrush family to use for buttons and switches. Disable TBMC (Tablet Mode Switch device), as it is not needed anymore. BUG=b:227240985 BRANCH=guybrush TEST=manual test on Dewatt: Volume Up/Down and Power buttons, Tablet Mode switch Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Change-Id: Ic9980f2b5bf10b12f2bd666212b5bce925dc323d Reviewed-on: https://review.coreboot.org/c/coreboot/+/63394 Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Jon Murphy <jpmurphy@google.com> Reviewed-by: Kangheui Won <khwon@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-07mb/google/brya/var/nereid: Add WLAN power sequenceReka Norman
There are currently two issues related to the WLAN power sequencing on nereid: - If the EN pin GPP_B11 is not high during cold boot, the SoC gets stuck in S3. - During warm reboot, if we only assert RST without pulling the power low, then the kernel crashes. As a workaround while we investigate these issues, we pull the EN high in S5, then actively drive it low in bootblock and high in romstage to make sure it goes low during warm reboot. BUG=b:227694137, b:225261075 TEST=Cold boot succeeds, and there's no kernel crash during warm reboot. Change-Id: I1ca46d9649eff3f96a0e77db594d87288b29a83a Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63368 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Sam McNally <sammc@google.com>
2022-04-07mb/google/brya/var/nereid: Enable pen garageReka Norman
BUG=None TEST=evtest works: Select the device event number [0-14]: 9 Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "PRP0001:00" Supported events: Event type 0 (EV_SYN) Event type 5 (EV_SW) Event code 15 (SW_PEN_INSERTED) state 1 Properties: Testing ... (interrupt to exit) Event: time 1649153020.275201, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0 Event: time 1649153020.275201, -------------- SYN_REPORT ------------ Event: time 1649153025.848689, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1 Event: time 1649153025.848689, -------------- SYN_REPORT ------------ Event: time 1649153028.383195, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0 Event: time 1649153028.383195, -------------- SYN_REPORT ------------ Event: time 1649153080.869155, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1 Event: time 1649153080.869155, -------------- SYN_REPORT ------------ Change-Id: I0d5134737fc758a43e1fff95e9f2a20200991bb1 Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63370 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sam McNally <sammc@google.com> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2022-04-07mb/google/brya/var/nereid: Configure descriptor for either Type-C or HDMIReka Norman
Some bytes in the descriptor need to be set differently for Type-C and HDMI. To allow using a single firmware variant for both cases, update the descriptor at runtime based on fw_config. This is a temporary workaround while we find a better solution. The byte values were determined by changing the following CSE strap and comparing the generated descriptors: Type-C: TypeCPort2Config = "No Thunderbolt" HDMI: TypeCPort2Config = "DP Fixed Connection" The default value before updating the descriptor is Type-C, but this was chosen arbitrarily. BUG=b:226848617 TEST=Type-C and HDMI both work on nereid with fw_config set correctly. Change-Id: I2cc230e3bd35816c81989ae7e01df5d2c152062e Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63366 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Sam McNally <sammc@google.com>
2022-04-06mb/google/skyrim/var/baseboard: Set Clk request for WLAN/SD/SSD deviceChris.Wang
Setting the clock source depends on clock request pin for WLAN/SD/SSD device. Also turn off the unused (CLKREQ#3) clock sources.In skyrim, clock source 0/1/2 are routed for WLAN/SD/SSD device. BUG=b:227297986 BRANCH=none TEST=Build Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com> Change-Id: I21fb912b69f59717eb4e84c379f706a0257a9ed1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63295 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jon Murphy <jpmurphy@google.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-04-06ChromeOS: Promote variant_cros_gpio()Kyösti Mälkki
The only purpose of mainboard_chromeos_acpi_generate() was to pass cros_gpio array for ACPI \\OIPG package generation. Promote variant_cros_gpio() from baseboards to ChromeOS declaration. Change-Id: I5c2ac1dcea35f1f00dea401528404bc6ca0ab53c Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58897 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-06mb/google/brya: Enable dynamic debug capability for brya familySridhar Siricilla
The patch enables dynamic debug capability for Brya family of boards. BRANCH=MAIN BUG=b:153410586 TEST= Verified the CSE firmware update functionality on Brya Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Change-Id: I51b0e0bb4392d3fbdb50577d3644491ab90a33c3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/61381 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2022-04-06drivers/intel/fsp1_1: Rename hob finding functionsArthur Heymans
The hob finding functions are never looped over so there is no point for the 'next' inside their name. Change-Id: I18e452d313612ba14edda479d43f2797f6c84034 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63204 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2022-04-06ChromeOS: Drop filling ECFW_RW/RO state in CNVSKyösti Mälkki
This field was never meant to be filled out by coreboot, because it can't know what the right value for this will be by the time the OS is running, so anything coreboot could fill in here is premature. This field is only read by the chromeos-specific `crossystem` utility, not by kernel code, so if one does not run through depthcharge there'll be many more broken assumptions in CNVS anyway. Change-Id: Ia56b3a3fc82f1b8247a6ee512fe960e9d3d87585 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63290 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-06ChromeOS: Add legacy mainboard_ec_running_ro()Kyösti Mälkki
Motivation is to have mainboard_chromeos_acpi_generate() do nothing else than fill ACPI \OIPG package. Change-Id: I3cb95268424dc27f8c1e26b3d34eff1a7b8eab7f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58896 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2022-04-05mb/google/guybrush/var/dewatt: Correct samsung part number value in SPD dataChris.Wang
The value at offset 329 should be: 0x4B -> "K" not 0x48 -> "H" in ASCII code. BUG=b:224884904 TEST=Build, confirm the part number is matched the corresponding parts Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com> Change-Id: I35dc5f036a29cdf4763389b6425df99ff63bbfa0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63354 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Robert Zieba <robertzieba@google.com> Reviewed-by: Rob Barnes <robbarnes@google.com>
2022-04-05mb/google/guybrush/var/dewatt: Override SPD file for Samsung partsRobert Zieba
K4U6E3S4AB-MGCL and K4UBE3D4AB-MGCL require special SPD files. This commit overrides the default SPD files used for these parts BUG=b:224884904 TEST=Verified that Dewatt SKU1 and SKU3 boot with changes Signed-off-by: Robert Zieba <robertzieba@google.com> Change-Id: Ibd08f109765933640ea3d0ad442873c30fa14bc4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63282 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com>
2022-04-04mb/google/brya/var/vell: Tune I2C1/I2C7 bus speed for 1 MHzEddy Lu
Tune I2C parameters to make sure I2C1 and I2C7 bus speed is around 1MHz. BUG=b:207333035 BRANCH=none TEST=built and verified adjusted I2C speed around 1MHz Change-Id: I09a9edf723bb1198bbf5d71248abc07276cd94ff Signed-off-by: Eddy Lu <eddylu@ami.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63241 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-02mb/google/skyrim: Fix ESPI communication issuesKarthikeyan Ramasubramanian
* Use dedicated ALERT pin to resolve NO_RESPONSE error/status while getting target configuration. * Configure the ESPI to operate at 16 MHZ since operating at 33 MHz causes boot stall. BUG=b:226635441 TEST=Build and Boot to OS in Skyrim. Ensure that EC <-> AP communication is working fine through Host Command debug logs in EC console, ectool version command. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: I951afdada8ee4f917cdeba8e287e5a2ae77c97ee Reviewed-on: https://review.coreboot.org/c/coreboot/+/63286 Reviewed-by: Jon Murphy <jpmurphy@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-02herobrine: fix emmc and sd card clocksShelley Chen
Found an issue where emmc and sd clocks were being misconfigured due to using incorrect integer values when called instead of the defined enums. Fixing by splitting the clock_configure_sdcc() function into two (sdcc1 and sdcc2) as there was no commonality between the two cases anyway. As a result, we can also get rid of the clk_sdcc enum. BUG=b:198627043 BRANCH=None TEST=build herobrine image and test in conjunction with CB:63289 make sure assert is not thrown. Change-Id: I68f9167499ede057922135623a4b04202f4da9b5 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63311 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2022-04-01mb/google/guybrush: Remove elog_gsmi_cb_mainboard_log_wake_sourceRob Barnes
elog_gsmi_cb_mainboard_log_wake_source is called from SMI and causes eSPI transactions. If the SMI interrupts an ongoing eSPI transaction from the OS it will conflict and cause failures. Removing this call to avoid conflicts. This can be re-enabled after refactoring google_chromeec_get_mask to use ACPI MMIO. BUG=b:227163985 BRANCH=gubyrush TEST=No 164 errors detected during suspend_stress_test /sys/firmware/log output after resume before change: SMI# #1 ELOG: Event(B0) added with size 9 at 2022-03-31 19:52:51 UTC GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000 ELOG: Event(9F) added with size 14 at 2022-03-31 19:52:51 UTC Chrome EC: clear events_b mask to 0x0000000000000000 after change: SMI# #6 ELOG: Event(B0) added with size 9 at 2022-03-31 19:50:19 UTC GPIO Control Switch: 0xcf000000, Wake Stat 0: 0x00000000, Wake Stat 1: 0x00000000 ELOG: Event(9F) added with size 14 at 2022-03-31 19:50:19 UTC Change-Id: I3320e3fb8bd9e9e0db84332e1d147a0af25f7601 Signed-off-by: Rob Barnes <robbarnes@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63280 Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-04-01mb/google/brya/var/nereid: Add separate VBT for HDMIReka Norman
BUG=b:226848617 TEST=HDMI works on nereid Cq-Depend: chrome-internal:4650256 Signed-off-by: Reka Norman <rekanorman@google.com> Change-Id: I6a90d3d86b32f73ec0130e582539d1c5b045da62 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63239 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org>
2022-04-01mb/google/brya/var/nereid: Disable C1 PMC mux conn for HDMIReka Norman
BUG=b:226848617 TEST=HDMI works on nereid Signed-off-by: Reka Norman <rekanorman@google.com> Change-Id: I039c30f95d959dba489b24b6938d08da937c5e03 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63238 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org>
2022-04-01mb/google/skyrim/var/skyrim: Add ELAN trackpad configKarthikeyan Ramasubramanian
Add support for ELAN trackpad on I2C0 bus. BUG=None TEST=Build and boot to OS in Skyrim. Perform evtest on Elan trackpad. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: Ia1522af3f35ef131dda74c4aabecc4fa532dfbec Reviewed-on: https://review.coreboot.org/c/coreboot/+/63236 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-04-01mb/google/brya/variants/baseboard/brask: Turn off NFC power in S0ixAlan Huang
Turn off the NFC power which is controlled by GPP_D3 to save power in S0ix states. For an USB device, the S0ix hook is needed for the on/off operations to take place. BUG=b:202737385 BRANCH=firmware-brya-14505.B TEST=measure the voltage of GPP_D3 in S0ix states Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com> Change-Id: I69588c82dfde1744c45c7aff3ac05b80bb16a8f3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63191 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-04-01mb/google/brya/var/primus{4es}: Decrease touchscreen T3 timing to 200msCasper Chang
We set T3 as 300ms to meet Elan's spec, but the resume/suspend times are greater than 500ms, which is the spec for Chromebooks. The actual kernel timing has been measured, and given the ACPI delay after deasserting reset in addition to the delay until the kernel driver accesses the device, delaying only 200ms in the ACPI method is also sufficient to meet the 300ms requirement. BUG=b:223936777 BRANCH=none TEST=build and test touchscreen function on DUT. TEST=suspend, wake DUT and check touchscreen function. Change-Id: I6b04cf6392d924aed01ca36b720f889b88d92311 Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63201 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-04-01mb/google/brya/var/nereid: Enable AUX DC biasing on C0 and C1Reka Norman
C0 has no redriver, so enable SBU muxing in the SoC. C1 has a redriver which does SBU muxing, so disable SBU muxing in the SoC. However, this also disables AUX biasing when the pins are configured as NF6. So instead configure the C1 AUX bias pins as GPO. BUG=b:227259673 TEST=Voltages are correct on the C0 and C1 AUX bias pins Change-Id: Ic0af662ecc1c6cee15b4ae98cb02deeefc93a71e Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63199 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sam McNally <sammc@google.com>
2022-03-31mb/google/brya/var/agah: Replace amp max98390 with max98360Tony Huang
Based on the latest schematic, agah will replace the Maxim 98390 speaker amps with Maxim max98360. This patch updates the devicetree entries to reflect that. BUG=b:210970640 BRANCH=brya TEST=emerge-draco coreboot Change-Id: I7ea36d276f7ffeae1510483027092e2bc59690fc Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63196 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-31mb/google/brya/var/agah: Add GL9750 SD card reader supportTony Huang
BUG=b:210970640 TEST=emerge-draco coreboot Change-Id: I881c2c1ad7b0d10b7ae38fcd9814f757cf56feb5 Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63194 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-31mb/google/brya/var/kinox: set GPP_D0 to NCDtrain Hsu
Brask set GPP_D0 to GPO in commit b0769db4, but Kinox doesn't support fingerprint. This patch sets GPP_D0 to NC for matching schematic. BUG=b:214025396 BRANCH=firmware-brya-14505.B TEST=emerge-brask coreboot Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com> Change-Id: I38b9eb2df83cfbdb58d95cb178c1d767299aa4da Reviewed-on: https://review.coreboot.org/c/coreboot/+/63195 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
2022-03-30mb/google/brya/var/kano: Remove SAR sensorDavid Wu
RF team comfirmed that SAR sensor is not necessary for MP, therefore remove the corresponding entries from the devicetree. BUG=b:202978964 TEST=Build pass. Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I31faf18563848f8d6787fe70bfb28006efea8427 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63165 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-30mb/google/brya/variants/crota: Add memory config for crotaTerry Chen
Fill in the memory config based on the the schematic by bernadino 14 adl-p 20220112.pdf BUG=b:219891328 Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com> Change-Id: I981d2cd6feafee8c10ec9724a3dec9a23ba0ddd7 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63137 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-30Revert "mb/google/brya/var/kano: adjust I2C3 speed"David Wu
This reverts commit 65aaccda5910e9c74aaa2a44ea84119d9476c902. Reason: 1. Fix firmware messages show [ERROR] dw_i2c:invalid bus speed 390000 2. Measure DVT I2C3 speed < 400KHz. BUG=b:215095284 TEST=There isn't ERROR messages and verify I2C3 speed < 400KHz. Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I5982c82a55710824692b41e263418e4b4d420b02 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63168 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-30mb/google/skyrim: Call espi_switch_to_spi1_padsRaul E Rangel
We are using the second SPI pads for eSPI. BUG=b:226635441 TEST=Build skyrim Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I43713d7376a28ced2be635668836464ceec46392 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63096 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-03-30mb/google/guybrush/var/dewatt: add specific SPD hex for dewattChris.Wang
Add the specific SPD hex file for the Samsung memory part with updating the part number into the SPD table. The ABL needs to identify the part by checking SPD data to do the proper tuning. BUG=b:224884904 TEST=Build, validate the SPD data has been applied. Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com> Change-Id: Ia54726ce8c1bae46dcd4fed3df509ef184914e94 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63132 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com>
2022-03-30mb/google/brya/variants/crota: init overridetree for crotaTerry Chen
init overridetree.cb based on the schematic bernadino 14 adl-p 20220112.pdf BUG=b:226315394 Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com> Change-Id: Ibca9d93a81469730e472a645c607a97a624e9a1c Reviewed-on: https://review.coreboot.org/c/coreboot/+/63022 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-30mb/google/brya/var/banshee: Update the GPP_D12 as USB_C3_LSX_RXFrank Wu
Update the GPP_D12 according to USB_C3_LSX_RX. BUG=b:225081954 BRANCH=firmware-brya-14505.B TEST=emerge-brya coreboot chromeos-bootimage The device can be recognized when it is attached in port3. localhost /sys/bus/thunderbolt/devices # ls 0-0 1-0 1-0:3.1 1-3 domain0 domain1 Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Change-Id: I38caa76c855e683eb0587eb67ee9abc91af4545d Reviewed-on: https://review.coreboot.org/c/coreboot/+/63174 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2022-03-30mb/google/cherry: Add PCIe domain support for dojoJianjun Wang
Add override device tree for dojo and add PCIe domain support. Reference: - MT8195 Register Map V0.3-2, Chapter 3.18 PCIe controller (Page 1250) TEST=Build pass and boot up to kernel successfully via SSD on Dojo board, here is the SSD information in boot log: == NVME IDENTIFY CONTROLLER DATA == PCI VID : 0x15b7 PCI SSVID : 0x15b7 SN : 21517J440114 MN : WDC PC SN530 SDBPTPZ-256G-1006 RAB : 0x4 AERL : 0x7 SQES : 0x66 CQES : 0x44 NN : 0x1 Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006 BUG=b:178565024 BRANCH=cherry Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Change-Id: Ifb02960504177fe488e6784b954c16b2c8d94972 Reviewed-on: https://review.coreboot.org/c/coreboot/+/62360 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2022-03-30mb/google/brya/var/taeko: Add new FW_CONFIG option for THERMAL for tarloJoey Peng
Add thermal table settings for tarlo which shares the same firmware with taeko BUG=b:215033683 TEST=emerge-brya coreboot Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com> Change-Id: I37f79cde502115bbf65bb97216eddb6ea22b1648 Reviewed-on: https://review.coreboot.org/c/coreboot/+/62954 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-30mb/google/guybrush: Disable EN_SPKR on initYu-Hsuan Hsu
We don't want to enable the speaker on init. It will be enabled while using GPIO AMP codec in depthcharge. BUG=b:223289882 TEST=boot guybrush and verify the devbeep and gpio value in kernel Change-Id: Ic949cc95556913a2afef4a683a49eaa1e07e6147 Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63145 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2022-03-30mb/google/nissa/var/nivviks: Move WWAN power on sequence forwardEric Lai
Move WWAN power on sequence from OS to coreboot. This can save the WWAN initial time about 10S. Another purpose is power resource be removed because we don't power off the LTE in S0ix. BUG=b:223490884 TEST=FM101-GL work as expected. Enumerate time from [ 17.747145] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd [ 17.760192] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04 [ 17.760210] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 17.760215] usb 4-2: Product: Fibocom FM101-GL Module [ 17.760220] usb 4-2: Manufacturer: Fibocom Wireless Inc. [ 17.760224] usb 4-2: SerialNumber: 9c88998f to [ 3.936409] usb 4-2: new SuperSpeed USB device number 2 using xhci_hcd [ 3.966695] usb 4-2: New USB device found, idVendor=2cb7, idProduct=01a2, bcdDevice= 5.04 [ 3.989989] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.003813] usb 4-2: Product: Fibocom FM101-GL Module [ 4.019760] usb 4-2: Manufacturer: Fibocom Wireless Inc. [ 4.019762] usb 4-2: SerialNumber: 9c88998f Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Change-Id: I0f3fe999ae3a109b739629948b619a389a9059b1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63129 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Reka Norman <rekanorman@chromium.org>
2022-03-30mb/google/brask/variants/moli: update GPIOs for moliRaihow Shi
Follow the Moli GPIO Table_20220324.xlsx to update it. 1.Set A15 as the default value. 2.Set A14, A19 NC. 3.Set C3, C4 as the default value. 4.Set D9 as the default value. 5.Set E5, E13 as the default value. 6.Set R4, R5 as the default value. 7.Update E14. 8.Set E12 as the default value. 9.Set D16 as the default value. BUG=b:220821454 TEST=emerge-brask coreboot. Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com> Change-Id: Ia54256244111a99cb130b74f78c37815099a021a Reviewed-on: https://review.coreboot.org/c/coreboot/+/62802 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2022-03-30mb/google/brya/var/agah: Fix GPU GPIOsTim Wawrzynczak
While adding this train of patches to program the dGPU power sequences, I noticed some of the GPU GPIOs are incorrectly programmed in ramstage, so this patch fixes the settings. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I622b1f5cfba84727bb31792358ca4162c7fa9f52 Reviewed-on: https://review.coreboot.org/c/coreboot/+/62383 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com>
2022-03-30mb/google/guybrush/var/dewatt: Update telemetry valueKenneth Chan
AMD SDLE testing had been done and apply the following telemetry settings for dewatt EVT: vdd scale: 91288 vdd offset: 279 soc scale: 29785 soc offset: 461 BUG=b:219626910 TEST=1. emerge-guybrush coreboot 2. pass AMD SDLE test Change-Id: I4456ffddbf9963f1202a349abe52df2bbb726468 Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63136 Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-03-29mb/google/skyrim: Disable PSP postcodesKarthikeyan Ramasubramanian
ESPI is not initialized in PSP. Hence any attempt to write to port80 causes failure to boot. Disable PSP postcodes for now and re-enable it later after ESPI is initialized in PSP. BUG=b:224618411 TEST=Build and boot to OS in Skyrim. Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: I73b7ddec50936f7836f915f459ca0bdc0777cb22 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63119 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-03-29mb/google/cherry: Pre-initialize PCIe at the bootblock stageJianjun Wang
Described in PCIe CEM specification sections 2.2 (PERST# Signal) and 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should be delayed 100ms (TPVPERL) for the power and clock to become stable. Instead of asserting PERST# right before PCIe initialization and waiting for 100ms, which is currently the only function of 'mtk_pcie_pre_init', so that the extra 100ms delay in ramstage is avoided. TEST=Build pass and boot up to kernel successfully via SSD on Dojo board, here is the SSD information in boot log: == NVME IDENTIFY CONTROLLER DATA == PCI VID : 0x15b7 PCI SSVID : 0x15b7 SN : 21517J440114 MN : WDC PC SN530 SDBPTPZ-256G-1006 RAB : 0x4 AERL : 0x7 SQES : 0x66 CQES : 0x44 NN : 0x1 Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006 BUG=b:178565024 BRANCH=cherry Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Change-Id: Id5b9369e6f8599f93415588ea585c952a41c5e7d Reviewed-on: https://review.coreboot.org/c/coreboot/+/62359 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com>
2022-03-29mb/google/brya/var/felwinter: Update GPP_E19 from NF to NCJohn Su
Configure GPIO according to b:224107199 comment#15. - GPP_E19 from NF to NC. BUG=b:224107199 TEST=emerge-brya coreboot Signed-off-by: John Su <john_su@compal.corp-partner.google.com> Change-Id: I06d02c5a8b6cf65d5643eaf30fb277c3321dac8b Reviewed-on: https://review.coreboot.org/c/coreboot/+/63116 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subratabanik@google.com> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com> Reviewed-by: Derek Huang <derek.huang@intel.corp-partner.google.com> Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
2022-03-29mb/google/cherry: support max98390 audio ampTrevor Wu
The Cherry follower projects may choose Max98390 for audio output so we have to add a new config CHERRY_USE_MAX98390. Also, the 'dojo' device is the first one to use it. BUG=b:204391159 BRANCH=cherry TEST=emerge-cherry coreboot TEST=Verify beep function through CLI in depthcharge successfully Signed-off-by: Trevor Wu <trevor.wu@mediatek.com> Change-Id: I9b6bc5a5520292dd502b0389217f5062479b4490 Reviewed-on: https://review.coreboot.org/c/coreboot/+/63083 Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2022-03-28mb/google/skyrim: Implement mb_set_up_early_espiRaul E Rangel
This will setup the eSPI GPIOs in bootblock right before eSPI init. BUG=b:226635441 TEST=build skyrim Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I6ff32bf840aa4b757e98d876cbd4e2ba15a760da Reviewed-on: https://review.coreboot.org/c/coreboot/+/63094 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-03-28mb/google/skyrim: Swap eSPI_CS_L and SOC_DISABLE_DISP_BLRaul E Rangel
The eSPI CS function only exists on AGPIO30. We will need to rework all boards to make eSPI function. I also fixed the comments on the other eSPI pins. BUG=b:226635441 TEST=Build skyrim Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Ib03c0a7dcad31d10dd4bad0d10a0184ab84aef9a Reviewed-on: https://review.coreboot.org/c/coreboot/+/63093 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-03-27mb/google/skyrim: Add DXIO descriptorsJon Murphy
Add Skyrim DXIO descriptors using info from AMD and skyrim bouard shematics. BUG=b:225179599 TEST=Boots to OS on Skyrim Board Signed-off-by: Jon Murphy <jpmurphy@google.com> Change-Id: Ib68cf3d64641b006e0f2c4805af22b44a505a0d1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/62903 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2022-03-27mb/google/hatch/moonbuggy: Update GPIOsPablo Ceballos
Implement the GPIOs that have been changed from genesis. - Connect scaler UART on pins C12/C13 - Connect the HDMI redriver I2C on C18/C19 - Connect the iMX8 signals on D1/D2/D3/D21/D22 - Connect the EC interrupt on D14 (same as on scout) - Connect PCH_TYPEC_UPFB on E15 (same as on genesis) - Configure as not connected the following unused pins: D23, E11, E12, F11 -> F22, H0, H8, H9 BUG=b:200876872 TEST=moonbuggy boots Change-Id: Ie9cafe81e391bce6ab7ffbe23c2d57b407d146f3 Signed-off-by: Pablo Ceballos <pceballos@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/63014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2022-03-27mb/google/brya/var/banshee: Add mic mute switch settingFrank Wu
Using the GPP_F22 as mic mute switch based on the latest schematic. BUG=b:223737606, b:216110896 BRANCH=firmware-brya-14505.B TEST=emerge-brya coreboot chromeos-bootimage The mic_mute event is changed when the mic_mute GPIO pin is switched. Event: time 1647939954.639995, type 5 (EV_SW), code 14 (SW_MUTE_DEVICE), value 0 Event: time 1647939954.639995, -------------- SYN_REPORT ------------ Event: time 1647939954.648152, type 5 (EV_SW), code 14 (SW_MUTE_DEVICE), value 1 Event: time 1647939954.648152, -------------- SYN_REPORT ------------ Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com> Change-Id: I6f7176afbd64f7c080f02369f195043a2df88e5d Reviewed-on: https://review.coreboot.org/c/coreboot/+/62804 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-27 01:57:19 +0000