summaryrefslogtreecommitdiff
path: root/src/mainboard/google
AgeCommit message (Collapse)Author
2018-03-06google/snappy: enhance CCD type-A USB 2.0 phy strengthKevin Chiu
Alan(11")/BigDaddy(14") right type-A(port#2), CCD(port#4) are occasionally undetectable. USB 2.0 phy needs an override to enhance drive strength. right type-A port#2 PERPORTPETXISET: 4 PERPORTTXISET: 4 IUSBTXEMPHASISEN: 1 PERPORTTXPEHALF: 0 CCD port#4 PERPORTPETXISET: 7 PERPORTTXISET: 7 IUSBTXEMPHASISEN: 1 PERPORTTXPEHALF: 0 BUG=b:72922816 BRANCH=reef TEST=emerge-snappy coreboot Change-Id: I2b18c11709280d00ec3a6ef10f93a416acb4fb45 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/24969 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-06mainboard/google/fizz: Check HDMI HPD and DisplayPort HPDDaisuke Nojiri
Some type-c monitors do not immediately assert HPD. If we continue to boot without HPD asserted, Depthcharge fails to show pictures on a monitor even if HPD is asserted later. Also, if an HDMI monitor is connected, no wait is needed. If only an HDMI monitor is connected, currently the API always loops until the stopwatch expires. This patch will make the AP skip DisplayPort wait loop if it detects an HDMI monitor. And if an HDMI monitor is not detected, the AP will wait for DisplayPort mode (like before) but also its HPD signal. This patch also extends the wait loop time-out to 3 seconds. BUG=b:72387533 BRANCH=none TEST=Verify firmware screen is displayed even when a type-c monitor does not immediately assert HPD. Verify if HDMI monitor is connected, AP does not wait (and firmware screen is displayed on HDMI monitor). Change-Id: I0e1afdffbebf4caf35bbb792e7f4637fae89fa49 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23816 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-06mb/google/fizz: Skip FSP init for UART 0Duncan Laurie
The GPIO pins for UART 0 on Fizz are routed to the add-in card slot and should not be used as a UART device. coreboot is setting the pins to GPIO Mode but FSP is re-configuring them for Native Mode and the behavior is unexpected when the kernel tries to initialize the UART device. The UART 0 device is PCI function 0 so it needs to be enabled for other functions to be visible to the OS so it can't just be disabled. Instead, set the device to PchSerialIoSkipInit so that FSP will not change the pin state. BUG=b:73006317 TEST=Tested with add-in card on fizz hardware to ensure the pin state does not change when FSP runs or the kernel boots. Change-Id: Id97c1e482ef0d5642fcf9018d802e1d0e073263d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/24973 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-06Revert "mainboard/google/meowth: enable PCH iSCLK"Lijian Zhao
This reverts commit 2e81f394cffc6f1993a5f004356ed35f6064fe48, as it will have side effect that will make system shutdown failure. System will not enter S5 sleep state, instead a global reset will be generated. Once camera driver ACPI framework ready, isclk programing will be moved into APCI method, in _PS3, isclk will be turned off to save power. BUG=b.72532565 BRANH=master TEST=Apply the changes and flash coreboot, on meowth devices, issue "halt" in OS stage, system can shutdown successfully. Change-Id: If35697911f97c524d9b52bdf4dae5c9ef1cc8618 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/25006 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-05mb/google/poppy: Allow use of optional secondary SPDFurquan Shaikh
This change adds support for variants to use secondary SPD if required. This enables a variant to have different types of memory supported using the same image. BUG=b:73514687 Change-Id: I3add65ead99c510f2d6ec899fbf2cb9a06c79b0c Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/24972 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-05mb/google/poppy/variants: Set pch_trip_temp to 75CFurquan Shaikh
Similar to Soraka, this change sets the pch_trip_temp value to 75C. This is important so that PMC can shutdown the thermal sensor when CPU is in C-state and DTS temp <= pch_trip_temp. BUG=b:74089135 Change-Id: Ic46fa0681796b821dfb014ab91734c960df7846a Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/24968 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-03-02sb/intel/common: Fix conflicting OIC register definitionNico Huber
Commit d2d2aef6a3 (sb/intel/{bd82x6,ibexpeak}: Move RCBA macros to a common location) makes some platforms use the wrong OIC register defi- nition. It was extended to 16-bit in the corporate version of ICH10. So let's give the new size and location a new name: EOIC (extended OIC). This only touches the systems affected by the mentioned change. Other platforms still need to be adapted before they can use the common RCBA definitions. Change-Id: If9e554c072f01412164dc35e0b09272142e3796f Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: https://review.coreboot.org/24924 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Bill XIE <persmule@gmail.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2018-03-02mb/google/zoombini/variants/meowth: Enable NVMeBora Guvendik
Turn on pcie ports 9,10. Enable Root Port 9 and set up clkreq 3. BUG=b:72120814 TEST: Boot to OS via NVMe Change-Id: I272b63b11e6b00ae5bdbef5a37ee517cc0636f6d Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Reviewed-on: https://review.coreboot.org/23208 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-02mainboard/google/zoombini/variant/meowth: enable speed shiftNick Vaccaro
BUG=b:73817825,b:69011806 BRANCH=master TEST=Build and flash to meowth, verify cpufreq shows up in kernel for all cores : localhost ~ # find / -name "cpufreq" /sys/devices/system/cpu/cpu3/cpufreq /sys/devices/system/cpu/cpu1/cpufreq /sys/devices/system/cpu/cpufreq /sys/devices/system/cpu/cpu2/cpufreq /sys/devices/system/cpu/cpu0/cpufreq /sys/module/cpufreq /usr/share/laptop-mode-tools/modules/cpufreq Change-Id: I63242b2b049e37167c0d3b8eab630cb6e15a75fd Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/24902 Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-01mb/google/reef/sand: Override USB2 phy settingsKatherine Hsieh
Sometimes the USB device is not detected. USB2 port#1 and #4 PHY register need to be overridden. port#1: PERPORTPETXISET = 4 PERPORTTXISET = 4 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 port#4: PERPORTPETXISET = 7 PERPORTTXISET = 7 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 BUG=b:72623892 BRANCH=master TEST=emerge-sand coreboot chromeos-bootimage Change-Id: I4051aefbec4583bb1f8babec08fdbeb27f749769 Signed-off-by: Katherine Hsieh <Katherine.Hsieh@quantatw.com> Reviewed-on: https://review.coreboot.org/23879 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-01mainboard/google/meowth: Turn on DBC over USB3.0Lijian Zhao
Intel DCI (direct connect interface) allows debug Intel target using USB3.0 ports. It will support debug via USB stack (DCI Dbc) using USB3.0 only. BUG=None TEST=Turn on DCI trace hub in descriptor.bin and flash the coreboot image. Using DAL to halt/run CPU. Change-Id: I39e68dabfcb9e659733019334299e562eee3681d Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/23446 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2018-03-01mb/google/poppy/variant/nautilus: Change SlowSlewRateForSa settingSeunghwan Kim
If switch to VT2 on nautilus, screen flicker appears. We found if we rollback the change of slew rate setting, then the flicker issue will be gone: https://review.coreboot.org/c/coreboot/+/22588 But nautilus board needs slew rate tuning to reduce EE noise, so we decided to change only SlowSlewRateForSa to 2 (Fast/8) instead of rollback the whole change of the CL:22588. It can remove the flicker on VT2. BUG=b:71397040 BRANCH=master TEST=emerge-nautilus coreboot Change-Id: Id1d4bd8b1316c02c783de708ec4658e030193a26 Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/23877 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-01mb/google/reef: Override USB2 phy settingsTim Chen
Sometimes the USB device is not detected. USB2 port#1 and #4 PHY register need to be overridden. port#1: PERPORTPETXISET = 4 PERPORTTXISET = 4 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 port#4: PERPORTPETXISET = 7 PERPORTTXISET = 7 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 BUG=b:72623892 BRANCH=master TEST=emerge-reef coreboot chromeos-bootimage Change-Id: Iab782ac6dfd81af839fff0e60e2b2460ce722733 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/23878 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-01mb/google/coral: add usb2 phy setting override for some variantsSheng-Liang Pan
Due to there are some chances USB devices can not be detected. USB2 port#1 and #4 PHY register need to be overridden for variants Santa/Lava/Blue/Bruce/Astronaut. port#1: PERPORTPETXISET = 4 PERPORTTXISET = 4 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 port#4: PERPORTPETXISET = 7 PERPORTTXISET = 7 IUSBTXEMPHASISEN= 1 PERPORTTXPEHALF= 0 BUG=b:72623892 BRANCH=master TEST=emerge-coral coreboot chromeos-bootimage Change-Id: I401905685cc3078df657919b162272c3de320296 Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com> Reviewed-on: https://review.coreboot.org/23881 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-01mb/{amd/gardenia,google/kahlee}: Initialize GPIOs earlierJustin TerAvest
The GPIOs for PCIe reset and power enable for WLAN must be set up before amdinitearly for wlan to function. BUG=b:73898539 TEST=Boot, see WLAN controller in lspci Change-Id: I568a3240a54817ab6dcf15fe39f7f1336943852b Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/24916 Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-28mainboard/google/zoombini: consolidate SPD makefilesNick Vaccaro
- consolidate commonality in meowth and zoombini's SPD makefiles into a common zoombini/spd/Makefile.inc - move all SPD hex files into zoombini/spd directory - move SPD_SOURCES definitions to variants/$(VARIANT_DIR)/Makefile.inc BUG=b:69011806,b:71776625 BRANCH=master TEST=Verify 'emerge-meowth coreboot' and 'emerge-zoombini coreboot' compile and boot successfully. Change-Id: I2291ebaf0ef5da1b22eb0e8fa7af8dbb50848c29 Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23874 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-28mb/google/poppy/variants/nami: Enable elan touchscreenCrystal Lin
BUG=b:72062694 BRANCH=master TEST=Verify touchscreen on nami works with this change. Change-Id: Iaec71a11121b3d2849f12d18cda0e506be2ace09 Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/23872 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-28mb/google/octopus: Add LPDDR4 memory initRavi Sarawadi
Add LPDDR4 initialization support. BUG=b:73136980 BRANCH=None TEST=Build coreboot for Octopus board. Change-Id: Ieffcfa2f9d075eb0be13562f1a0c7ee503b005d9 Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/23832 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-27sb/intel/{bd82x6,ibexpeak}: Move RCBA macros to a common locationArthur Heymans
Many generations of Intel hardware have identical code concerning the RCBA. Change-Id: I33ec6801b115c0d64de1d2a0dc5d439186f3580a Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/23287 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-02-26mainboard/google/zoombini: enable 4 coresNick Vaccaro
BUG=b:70731385 BRANCH=master TEST='emerge-meowth coreboot chromeos-bootimage', flash image.serial.bin to meowth board, boot into kernel, and verify 4 cores are running. Change-Id: Ia233e41acd19b317f82433a5d41d84ea934a66c4 Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23839 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-23mb/google/fizz: Enable PCIe port 11, 12Zhongze Hu
Our CFM daughter card would like to use individual PCIe lanes for two different devices on the card. dlaurie@ has reconfigured PCIe port 9-12 from 1x4 to 1x2 + 2x1 on b2b connector on fizz to meet the requirement: https://chrome-internal-review.googlesource.com/571936 We also need to enable the ports on device tree. BUG=b:72523836 TEST=none BRANCH=fizz Change-Id: Icded9850d833752680e0174b6c476e657817b319 Reviewed-on: https://chromium-review.googlesource.com/923867 Commit-Ready: Zhongze Hu <frankhu@google.com> Tested-by: Zhongze Hu <frankhu@google.com> Reviewed-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/924860 Commit-Queue: Shelley Chen <shchen@chromium.org> Tested-by: Shelley Chen <shchen@chromium.org> Signed-off-by: Zhongze Hu <frankhu@chromium.org> Reviewed-on: https://review.coreboot.org/23845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-02-22mb/google/kahlee/mainboard.c: Fix mainboard_picr_dataRichard Spiegel
While programming interrupts, a message "perhaps this device was defined wrong?" shows up twice. This is caused because some devices have interrupt programmed for APIC mode, but not for non-APIC mode. Fix mainboard_picr_data table by identifying devices programmed with value 0x1F while programmed differently on mainboard_intr_data table. Do so only for devices that are used by kahlee or interrupt required by old OS. BUG=b:70788755 TEST=Build and run kahlee, Verify that message disappears from serial output. Change-Id: Ic285036290519ed3ee617dffa616bd26c61575c5 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/23716 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-02-22mb/google/kahlee: Use GPIO macros for baseboardJustin TerAvest
This commit uses newly defined macros to make it easier to read which iomux function pads are being configured to use. TEST=Booted grunt, confirmed display backlight came on. BUG=b:72875858 Change-Id: I24e5091fc7ef696f8e9c932ce04664e6cc3ccb90 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23830 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-22mb/google/kahlee: Correct bad gpio entryJustin TerAvest
There's no need to set the output enable here; this is already handled by the native function. I'm making this correction in this change to prevent the GPIO pin descriptions from getting confusing. BUG=b:72875858 TEST=Booted, confirmed S5_MUX_CTRL high with and without this change. Change-Id: I9e047be7169586c59892ef2bdab915683feeebda Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23829 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-22mainboard/google/meowth: enable PCH iSCLKLijian Zhao
Turn on PCH iSCLK for meowth platform. BUG=None TEST=Boot up into OS and check register programming with iotools, the command is iotools mmio_read32 0xfdad8000, returned value is 0x03. Change-Id: I1e44e3748c9b37c8f60adcc47a866d445d77cfaa Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/23368 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-22mainboard/google: Disable big, pit, and ryu ec buildsMartin Roth
The EC builds for nyan_big, peach_pit, and smaug (ryu) have been removed from the latest EC codebase, so don't try to build them by default anymore. Change-Id: I53901b32753c5b9b050f517bbf3f10b9071913d4 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/23826 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-22mainboard/google/zoombini: Add config for meowth audioSathyanarayana Nujella
Add NHLT and dt support for meowth with max98373 amp. BUG=b:71724897 TEST='emerge-meowth coreboot' compiles correctly TEST=check SSDT and verify entries for max98373 TEST=check NHLT ACPI tables included blobs for max98373 Change-Id: Ic89bf669c7ab2ef39ce64e4da6a57a7069ee75f9 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/23334 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2018-02-21mainboard/google/kahlee: Add tis_plat_irq_statusChris Ching
For variants that have a cr50 tpm, this enables faster polling when interacting with the tpm. BUG=b:72838769 BRANCH=none TEST=verified on grunt that irq is used and not timeouts for tpm Change-Id: I5786d334b6c1cc70f4c7107c75b07a7e27ac4428 Signed-off-by: Chris Ching <chingcodes@chromium.org> Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/23626 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-20mb/google/poopy/variants/nami: Add Pmax settingGaggery Tsai
This patch adds the Pmax setting in device tree. The Pmax is from MAX(PL4_sku1, PL4_sku2, ..) + ROPmax. Given ROPmax is 30W and the maximum PL4 is from U42, hence the Pmax = 71W + 30W = 101W. BUG=b:72138778 BRANCH=None TEST=USE=fw_debug emerge-nami chromeos-mrc coreboot chromeos-bootimage & ensure the Pmax value is passed to FSP-S. Change-Id: Ief6a134dc5b6bd2b8e07b4a44450e99ff26402d9 Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/23640 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-20mb/google/kahlee/OemCustomize.c: Disable bank interleaveRichard Spiegel
AmdInitPost returns AGESA_WARNING. This is because AGESA by default enables bank interleaving, while the HW does not meet the requirements for it. Disable bank interleaving, thus clearing AGESA_WARNING. BUG=b:73118857 TEST= Build and run kahlee. Search for "agesawrapper_amdinitpost() returned AGESA_SUCCESS". Change-Id: Ice9270f9b10051dbb622344919223cf5439f5d7b Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/23763 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-17mb/google/fizz: Wait until display is readyDaisuke Nojiri
Fizz fails to show pictures on a type-c monitor because VBIOS runs before DisplayPort link is ready. With this patch, when firmware needs to display something, Fizz calls google_chromeec_wait_for_display to make sure display is ready. The penalty is up to 2 sec per boot in dev and rec boot. Normal boot won't affected unless there is EC update. BUG=b:72387533 BRANCH=none TEST=Verify screens are displayed on Fizz as follows: 1. Put DUT in normal mode 2. Flash EC image to trigger EC sync (critical update) 3. Trigger manual recovery (insert) 4. Hit ctrl+d to switch to dev mode (to-dev) 5. Confirm to reboot (dev warning) 6. Warm reboot (dev warning) 7. Cold reboot (dev warning) 8. Flash EC image to trigger EC sync (critical update) 9. Trigger manual recovery (insert) Change-Id: I90befe94f93e13904987acda50b2598d034b0031 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23746 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-17soc/amd/stoneyridge: Normalize GPIO initJustin TerAvest
This makes the flow for GPIO initialization more closely follow that what is performed for other boards so that it's easier to read the flow (and stops relying on BS_WRITE_TABLES). BUG=b:72875858 TEST=Built and booted grunt, built gardenia. Change-Id: Ic97db96581a69798b193a6bdeb93644f6a74fc9d Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23679 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-16mb/google/{soraka,poppy,nautilus}: Set psys_pmax to 45WNaresh G Solanki
Soraka, Poppy & Nautilus are designed to operate at max power of 45 Watt. Hence set psys_max to 45W. BUG=b:66066340 BRANCH=None TEST=Build and boot soraka. Change-Id: If6f624733830b462329b5f539c20e2aea664143e Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/23757 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
2018-02-16mb/google/zoombini/variants/meowth: enable FPMCU interruptVincent Palatin
Enable the micro-controller interrupt line as a real IRQ. BUG=b:71986991 BRANCH=none TEST=on Meowth, run 'ectool --name=cros_fp fpmode capture' and see the number of interrupts incrementing and the MKBP event happening. Change-Id: Ic0cf03d2a3508148b6482a5a595eaa213eff52c7 Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: https://review.coreboot.org/23769 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-16google/gru: Fix GPIO_WP pull and polarity for ScarletJulius Werner
Turns out the write-protect GPIO polarity for Scarlet is different than for Kevin/Gru, and nobody ever told us. Also, it must not be configured with an internal pull-up or we'll not read the correct value. This patch fixes both issues. BRANCH=scarlet BUG=b:73356326 TEST=Booted Scarlet, confirmed that crossystem wpsw_boot returns the right value in all cases. Change-Id: Idd348ecdf9da8fff7201b83e869ba097b8570f32 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/23767 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-15mb/google/poppy/variant/nautilus: Enable and configure DPTFSeunghwan Kim
This change enables DPTF and configures the policy. DPTF parameters were provided by internal power team. BUG=b:67877437 BRANCH=master TEST=emerge-nautilus coreboot Change-Id: I31b31d5282ab38278bc68045ce75fdc6192f1144 Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/23731 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-15mb/google/octopus: Add new boardHannah Williams
Add octopus board using GLK soc. Copied base code from mainboard/intel/glkrvp. TODO: Fix as per octopus schematic. Change-Id: Ic8c25b3fafbfef31b8b3b802acb3bc53ee7146b6 Signed-off-by: Hannah Williams <hannah.williams@intel.com> Reviewed-on: https://review.coreboot.org/23685 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-14mb/*/spd: Use normal binary numbers (0b0010) instead of special format (2b0010)Jonathan Neuschäfer
This format (one hex digit, followed by 'b', followed by binary digits) is arguably useful, but also confusing. Use the more common format instead. Change-Id: Ide7b0a999483a2dd863a70f8aa42cd0865e2babf Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/23715 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2018-02-13mb/google/poppy: Fix the SPD for samsung_dimm_K4A8G165WBFurquan Shaikh
Original SPD provided by the vendor had bytes after 254 shifted by 16 bytes. This change fixes the SPD data based on the latest details received from the vendor. BUG=b:72749394 TEST=Verified that the device with this memory part boots to OS fine. Also, mosys is able to dump the right memory information. Change-Id: I6938dea761c5785048aad69eeeaf50e2d0fa8ca1 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23729 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-12mainboard/google/zoombini/variants/meowth: enable touchscreenNick Vaccaro
BUG=b:69011806, b:72179988 BRANCH=master TEST=Verify touchscreen on meowth works with this change. Change-Id: Iad3f0b77a02552266435e523fdbb74b14ada101a Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/23551 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2018-02-12google/kahlee: Select HAVE_ACPI_RESUMEMarshall Dawson
TEST=Run powerd_dbus_suspend and resume with button press BUG=b:69614064 Change-Id: I0a5a610590b599b96dd0def211c4aa31c7a538ea Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/22732 Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-12google/snappy: enhance BigDaddy USB#2 2.0 strengthKevin Chiu
Fine tune 14" BigDaddy USB#2 2.0 strength: PERPORTPETXISET: 7 PERPORTTXISET: 1 IUSBTXEMPHASISEN: 3 PERPORTTXPEHALF: 0 this value could have USB#2 2.0 EA/function pass. BUG=b:72922816 BRANCH=reef TEST=emerge-snappy coreboot Change-Id: I0ea1b966b7c02c95bf0ea1138a5629fd3b576439 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/23649 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-11mb/google/fizz: Set SATA GPIOs in bootblockShelley Chen
Previously, we were seeing device boot into the recovery screen with error code 0x5a. This was root caused to the SATA GPIOs (specifically DEVSLP) not being initialized early enough, causing the SATA 1 link detection to time out and the device to reboot into recovery with 0x5a instead of booting into the OS as usual. BUG=b:69715162 BRANCH=None TEST=after flashing BIOS, set gbb flags to 0, then type reboot from the OS. Change-Id: I53913d5b7adaeb43edd0ef2d24a7cad92052d68a Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23647 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kane Chen <kane.chen@intel.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-10mb/google/poppy/variants/nautilus: set oem_id, oem_table_id fields of ↵Naveen Manohar
acpi_header_t This change makes the Nautilus platform update the two fields: *oem_id* and *oem_table_id*, if the Maxim codec is detected. Change is made to correct the audio topology file name that is being read from oem_id fields, loaded and displayed in dmesg. BUG=b:68686020 TEST=Build, booted nautilus board. Verified kernel reads new strings. Change-Id: I041f2838f07a2525be7a28fdc69b7f1af46d16f1 Signed-off-by: Naveen Manohar <naveen.m@intel.com> Reviewed-on: https://review.coreboot.org/23648 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-10mainboard/google/meowth: Enable ECT againLijian Zhao
Previously ECT was disabled in commit 22401, on D0 stepping system and FSP version 7.x.20.52, disabling ECT will cause memory training failure and the system is stuck at post code 00D5h. BUG=b.72473063 TEST=Apply patch and build coreboot image, flash into meowth P0 system with D0 stepping silicon installed, system can pass memory training and boot up into OS. Change-Id: I7dd0a7dfe2993ad9cfaf00050175e5a47468b471 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/23645 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2018-02-10mb/google/poppy/variants/nami: set oem_id, oem_table_id fields of acpi_header_tKaiyen Chang
This change makes Nami platform update the two fields: *oem_id* and *oem_table_id*, if the Maxim codec is detected. Change is made to correct the audio topology file name that is being read from oem_id fields, loaded and displayed in dmesg. BUG=b:70646770 TEST=Verify kernel reads new strings. Change-Id: I513a997f312e2d37d76da0379feb017d1f591f9a Signed-off-by: Kaiyen Chang <kaiyen.chang@intel.com> Reviewed-on: https://review.coreboot.org/23670 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-10mb/google/grunt: Add ADAU7002 to devicetreeDaniel Kurtz
Add an entry to the grunt devicetree defining the ADAU7002 PDM-to-I2S converter. BUG=b:72121803 TEST=With grunt audio kernel patches, "aplay -l" shows playback devices: **** List of PLAYBACK Hardware Devices **** card 0: acpd7219m98357 [acpd7219m98357], device 0: Playback da7219-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: acpd7219m98357 [acpd7219m98357], device 2: HiFi Playback HiFi-2 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Change-Id: I90b59ec64f4b841932db42b8a8970ed924283613 Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-on: https://review.coreboot.org/23660 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-10mb/google/kahlee: Add grunt audio codecs to devicetreeDaniel Kurtz
Remove manually written asl entries for grunt's DA7219 and MAX98357A audio codecs, and replace them with equivalent devicetree entries. BUG=b:72121803 TEST=With grunt audio kernel patches, "aplay -l" shows playback devices: **** List of PLAYBACK Hardware Devices **** card 0: acpd7219m98357 [acpd7219m98357], device 0: Playback da7219-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: acpd7219m98357 [acpd7219m98357], device 2: HiFi Playback HiFi-2 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Change-Id: Ia658c54a28a5363aabb4c50478adaca1f46d166a Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-on: https://review.coreboot.org/23658 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-02-08mb/google/poppy/variants/nami: Revise AC/DC loadlinesGaggery Tsai
This patch revises AC/DC loadlines from VRTT reports. +----------------+-------+-------+-------+-------+ | Domain/Setting | SA | IA | GTUS | GTS | +----------------+-------+-------+-------+-------+ | AcLoadline | 11 | 2.4 | 3.1 | 3.1 | | DcLoadline | 10 | 2.46 | 3.1 | 3.1 | +----------------+-------+-------+-------+-------+ BUG=b:72351128 b:72129954 BRANCH=None TEST=emerge-nami coreboot chromeos-bootimage & ensure the settings are passed to FSP. Change-Id: Ib8aeb82973c42723d7b623967f8085c8f1d926eb Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/23635 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-07mb/google/fizz: Set Pmax to 120 for all SKUsShelley Chen
The Pmax is calcuated from MAX(Psku1, Psku2), where Psku1, Psku2 are estimated Pmax power of U42 and U22 skus. For U42 sku, the Pmax is PL4 (71W) + ROPmax (49W) = 120W; for U22 SKU, the Pmax is PL4 (43W) + ROPmax (49W) = 92W. So Pmax is set to MAX(120W, 92W) = 120W. BUG=b:71594855 BRANCH=None TEST=Make sure correct pmax value is being passed into fsp Change-Id: Ic27fef87c869094b20438e6ee0e1eb0b35122b8d Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23633 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Chris Ching <chingcodes@chromium.org>
2018-02-07google/kahlee/grunt: Fix 2 device specific variablesAkshu Agrawal
* micbias_lvl -> micbias-lvl * mic_amp_in_sel -> mic-amp-in-sel BUG=b:71875600 TEST=Checked in kernel the values are set Change-Id: Ife7e8cdd835cc256cd8265593a94df84a510cebb Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Reviewed-on: https://review.coreboot.org/23603 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-07mb/google/poppy/variants/poppy: Enable EC_ENABLE_SECOND_BATTERY_DEVICENicolas Boichat
BRANCH=none BUG=b:65697620 TEST=Boot lux, both /sys/class/power_supply/BAT0 and BAT1 are present, data is valid. Change-Id: I869bf08341b83f359066709e1e9c03af99482b2c Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-on: https://review.coreboot.org/23599 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-02-07mb/google/poppy/variants/nami: Change WiFi wake pin to GPP_E22Furquan Shaikh
This change updates the WiFi device wake pin to GPP_E22 from WAKE# (to match the latest schematic changes). Since WiFi was the only device using WAKE# pin, DSX_EN_WAKE_PIN is removed from deep_sx_config as well. BUG=b:72697650 TEST=Verified: 1. Wake-on-wifi works. 2. Device is able to enter G3 without WAKE# pin causing unwanted wakes from deep S5. Change-Id: Ibde81f73cca322f9b8b45baf8ee18ae00521467d Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23594 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-06google/gru: Add another 512KB to the COREBOOT FMAP regionJulius Werner
With the new extra detachable UI elements, we're running out of space in Scarlet's RO CBFS. Thankfully, the GBB is still massively overdimensioned, so we can steal another half MB from there. This patch changes the FMAP for some boards that have already had production firmware releases. However, all the new changes are to the RO parts of the FMAP, so there shouldn't be a way this could cause a problem for updates. Change-Id: Iec182de3e894e56fec2a64b034c0ca65d78a5522 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/23595 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-06mb/google/kahlee: Fix grunt I2C rise/fall timesJustin TerAvest
I2C bus rise/fall times were measured as follows. Signals were generated with: - bus 0: manual i2c driver in depthcharge - bus 2,3: i2cdetect -r <bus_number> and then measured manually with an oscilloscope. BUG=b:72442912 Change-Id: I291e144249271ec34a93417398e54e68b8e21e23 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23520 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-06mb/google/kahlee: Remove cmos.layoutRichard Spiegel
CMOS layout is not used and can be removed. A change to Kconfig is needed in order not to break the build. BUG=b:64207749 TEST=Build kahlee. Change-Id: Ib5d18e80a56111d96c730420db865194c71de1b3 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/23596 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-02-06mb/google/eve: Enable HotPlug on PCIe root port for WiFiDuncan Laurie
Enable HotPlug for the PCIe root port that the WiFi device is on so the OS can re-train the link without needing a reboot if it goes down unexpectedly at runtime. BUG=b:72417777 TEST=enable HotPlug on Eve Root Port 0 (WiFi) and check in linux that it is identified as a HotPlug capable root port. Change-Id: Id2b7fc92c8c9128f0e28102eb5991bda7fbf6799 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/23512 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-06google/kahlee: Initialize non-early i2c buses in mainboard_initDaniel Kurtz
Initialize non-early i2c buses in ramstage. BUG=b:69407112 TEST=Boot depthcharge w/ CLI enabled on grunt. devbeep => plays beep BRANCH=None Change-Id: I634a7a823cc393243841dbd55e52abe3f0e72c5a Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-on: https://review.coreboot.org/23554 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-06mb/google/fizz: Determine PsysPl3 and Pl4 valuesShelley Chen
Pass in fizz-specific adapter-based PsysPl3 and Pl4 values to avoid brownouts. According to Intel doc #560604, page 74, the max time window is 64ms (code=6) and the min duty cycle we can set is 4%. BUG=b:71594855 BRANCH=None TEST=Boot to OS and check MSRs using iotools for expected values Change-Id: I06a4c5bc25f6ec036b79f6941f80e26058d64930 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23528 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-02-06mb/google/nautilus: Work around the power issue of MIPI and USB camerasAndy Yeh
On EVT, the USB and MIPI cameras share the same power source. As a result, when the MIPI camera driver turns off the camera once probed, USB camera will be disconnected. To make USB camera work on EVT devices, we will need a hack in coreboot to leave the camera power always-on. BUG=b:72839352 TEST: Verified the MIPI and USB camera function on DUT board TODO: This power issue will be fixed on DVT build. Will revert this patch once confirmed power sources for MIPI and USB camera could be supplied individually. Change-Id: Icaaf7e17447492f2e2f2d03eb9a35bcc53667f28 Signed-off-by: Andy Yeh <andy.yeh@intel.com> Reviewed-on: https://review.coreboot.org/23546 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Andy Yeh
2018-02-05mb/google/fizz: Get OEM ID and SKU ID from ECDaisuke Nojiri
This patch makes coreboot fetch OEM ID and SKU ID from EC. If it fails, it falls back to GPIO pins. BUG=b:70294260 BRANCH=none TEST=Verify AP log shows expected OEM ID and SKU ID on Fizz. Change-Id: I06d3a205275b46660b3974bc3673d4be8e13f6d1 Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-on: https://review.coreboot.org/23548 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-05google/lars: Turn on keyboard backlight in romstageJenny TC
Cherry-pick from Chromium: a60ac10 [Lars: Turn on keyboard backlight in romstage] Use the keyboard backlight to provide indication that the system is booting. This is useful for determining that a system is in S0 and is running BIOS code. TEST=boot on Lars and see keyboard backlight come on early Original-Change-Id: I4fede6cff85f4487cedfbccf6cc24c6380d905e0 Original-Signed-off-by: Jenny TC <jenny.tc@intel.com> Original-Tested-by: Divagar Mohandass <divagar.mohandass@intel.com> Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Change-Id: I4b1fed10d9bd1ae1b265e848417836f816f252f3 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23572 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars,lili: Update GPIO mappingdavid
Combination of several commits from Chromium tree: 949037c [Lars: coreboot GPIO changes for EVT] c286789 [Lars: Set USB Type A current limit to 2A] 0f1b26d [lars: set BOOT BEEP GPIO GPP_F_23 to output and Low] 4a0650d [Lili: Support touchscreen] Disable unused GPIOs based on schematic and adds GPIO mappings for HSJ_MIC_DET, PCH_BUZZER and AUDIO_INT_WAK. Set GPIOs USB_A0_ILIM_SEL & USB_A1_ILIM_SEL low to enable 2A charging from the USB Type-A port. GPP_F_23 is set to NC currently and is floating, causing the on-board speaker to have no audio or the audio has noise; set to output/low. These commits bring lars' GPIO mapping in line with the Chromium tree. Original-Change-Id: I3bf4aa8599255e5382d99810b4c83b4c97c648b6 Original-Change-Id: I328a8be22dc59492477cbe362a5d5b94aa80a397 Original-Change-Id: I253e55bf2b423363a00347778cabaa4184d85aec Original-Change-Id: I761f7c5ea5fc7a173c07a8c37da1338a1b2cd269 Original-Signed-off-by: David Wu <David_Wu@quantatw.com> Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com> Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Original-Reviewed-by: Shobhit Srivastava <shobhit.srivastava@intel.com> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Tested-by: David Wu <david_wu@quantatw.com> Original-Tested-by: Balaji Manigandan <balaji.manigandan@intel.com> Original-Tested-by: Kuen Liu <kuen.liu@quantatw.com> Change-Id: Ic2d188fbf913a11fbf6ad1f0eb3a5e72ba4cb1cf Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23571 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars: Update the MAINBOARD_FAMILY string in KconfigDuncan Laurie
Cherry-pick from Chromium: 99cd8f8 [lars: Update the MAINBOARD_FAMILY string in Kconfig] This string was left at the default for kunimitsu and should be updated to indicate the proper mainboard. Original-Change-Id: Icc0e162d57242e7b0610fb570ef1a8a45ee16e4f Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Change-Id: Ia4b70227c8cfdfe939e40ea6258d494337a2907b Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23570 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars,lili: Update SPD DataMatt DeVillier
Combination of several commits from Chromium tree: 3b875a2 [Lars: Update Memory ID for DVT board] b6d7c63 [Lili: Update Memory IDs] f203f99 [Lili: Add new SPD for Hynix H9CCNNN8GTALAR-NUD] a6571bf [Lili: Update Memory IDs] 80e1841 [Lili: Update Memory IDs] 58d4487 [Lili: Fix memory string show error in spd data] These commits bring lars' SPD data in line with the Chromium tree. Original-Change-Id: I54d0e6d2bbe86d5dc2ee5825f332d36abfa99084 Original-Change-Id: I9431393f369a1d2870bdabba1fc55d9cefae5c39 Original-Change-Id: I3b325a1801f49109429eb647d8d98a5537ce1b7b Original-Change-Id: Ie8a32d8a26ea1054e2df8432084a95d1cb03f991 Original-Change-Id: I64c73950e3bea57b6c5a90257211b3d6d7f1baab Original-Change-Id: I0e425fa4f0bae544680d5522c2e05a4f7a3be95a Original-Signed-off-by: David Wu <David_Wu@quantatw.com> Original-Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Reviewed-by: Duncan Laurie <dlaurie@google.com> Original-Tested-by: David Wu <david_wu@quantatw.com> Original-Tested-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Change-Id: I7cc9b01012b0b9ed72804192bb5953243fc859b4 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23569 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars: Add sdmode-delay property for max98357aMatt DeVillier
Adapted from Chromium commit: af3ec09 [Lars: Add sdmode-delay device property for maxim98357a] Add "sdmode-delay" as a device property for the maxim98357a codec. This speaker amp requires both SFRM & BCLK to active and stable before it is unmuted. If there is a BCLK and no SFRM, that results in a pop noise. Adding a configurable delay parameter for all Skylake platforms to allow sufficient time for the BCLK & SFRM on I2S to be stable before the amp unmutes itself to avoid a pop noise at the start of playback. Setting the delay to 5ms since the observed delay between SFRM and unmuting of the amp is around 2ms. Adaptation needed to account for parameters having moved from mainboard.asl to devicetree in upstream tree. Original-Change-Id: I1fff4f86ff816e907553e7a6f1d05713f9d85084 Original-Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Change-Id: I8a1c52ccdb08df9a4ab293e12bb266309e08737b Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23568 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars: update device properties for Nuvoton codecMatt DeVillier
Adapted from Chromium commit: 848ee3a [Lars: Add device properties for Nuvoton codec] Update sar-threshold, sar-compare-time, sar-sampling-time properties to match values in lars' Chromium branch. Adaptation needed to account for parameters having moved from mainboard.asl to devicetree in upstream tree. Original-Change-Id: Id0c28e50406a29e6f33d04ca78fd2a3e3974fa90 Original-Signed-off-by: David Wu <David_Wu@quantatw.com> Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Reviewed-by: Benson Leung <bleung@chromium.org> Original-Tested-by: David Wu <david_wu@quantatw.com> Change-Id: I2748a315d27eb947197109808b4d5fa8a82c8cf3 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23567 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars,lili: Set new thermal parametersdavid
Cherry-pick from Chromium: 55c0eb3 [Lili: Set new thermal parameters] Set new parameters of DPTF for both Lars and Lili. The acoustic will have higher 1.6dB in transition mode, when using Lili fan table on Lars. Original-Change-Id: I730ac483e2a6d43c8dcfe94da6761194c14f3163 Original-Signed-off-by: David Wu <David_Wu@quantatw.com> Original-Reviewed-by: Duncan Laurie <dlaurie@google.com> Original-Tested-by: David Wu <david_wu@quantatw.com> Change-Id: I3bf16db43bb90a542c6526f3bc891f820da00ca0 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23566 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05google/lars: Update DPTF settingdavid
Cherry-pick from Chromium: dff141b [Lars: Update DPTF setting] Original-Change-Id: I1f2686eced07c7fb1bde3c660df6d6efac607695 Original-Signed-off-by: David Wu <david_wu@quantatw.com> Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Change-Id: Ifd3e844688588b6d1c69459f75c0d7da93ba3688 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23565 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-02-05mb/google/kahlee: Enable wlan card so it can be detectedMartin Roth
The wifi card was not being powered, and was being held in reset during PCI enumeration, so it was not being brought up. BUG=b:72738963 TEST=Verify wlan card shows up in lspci Change-Id: I5a1e83298af35aa80c67c75cd6ec0a2c3213891e Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/23552 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-02-02google/gru: Use newer version of Innolux P097PFG panel init codeLin Huang
There is a line artifact in the lower third of the display with the current initialization code. So update it with code provided by Innolux to fix this issue. BUG=b:69689064, b:72191820 TEST=boot on dru with an Innolux panel and artifact line disappear. Change-Id: I9679c4f7f706fd6cd2e1dba7ec79e772fe3f227a Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-on: https://review.coreboot.org/23561 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-02-02mb/google/kahlee/mainboard.c: Create mainboard_pirq_dataRichard Spiegel
When booting kahlee, there's an error message: "Warning: Can't write PCI IRQ assignments because 'mainboard_pirq_data' structure does not exist". This is generated by write_pci_cfg_irqs due to missing mainboard_pirq_data. BUG=b:70788755 TEST=Build and boot kahlee. Warning message must be gone. Change-Id: If07d2f54f06f6cf77566c43eddc8ee8a314e7a3a Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/22940 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-02-01mb/google/kahlee: always load and run display opromAaron Durbin
The kernel requires the display oprom is loaded *and* ran in order for the kernel to not panic. Therefore, select the correct settings such that normal mode works for Chrome OS. BUG=b:72400950 Change-Id: Ibae5bc6b382cbe71a55c2386a24bb420cb8f313f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/23506 Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-31mb/google/kahlee: Add grunt cr50 supportJustin TerAvest
This commit adds an entry for H1/Cr50 into the devicetree for setting up ACPI entries for H1 communication. BUG=b:69250772 TEST=See probe messages in dmesg Change-Id: Id55ce3364ea4acdb62782758e5bcb2a167286cb9 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23514 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-31mb/google/kahlee: Add grunt trackpad in devicetreeJustin TerAvest
This commit removes a manually written asl file in favor of configuring the trackpad through devicetree. BUG=b:72121803 TEST=cat /proc/interrupts with trackpad connected Change-Id: I38afcf89ea64ffaf6a10bb317c41154feda57e50 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23508 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-01-31mb/google/poppy/variants/nautilus: Add gpio-keys ACPI node for PENHFurquan Shaikh
This change uses gpio_keys driver to add ACPI node for pen eject event. BUG=b:71329519 TEST=Verified using evtest that pen eject event results in events as expected. Change-Id: Ib293c2ca532c8ed9e2587143b1a69300cd9fa4e9 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23238 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-01-30mainboard/google/zoombini/variant/meowth: enable FCAM_PWR_ENNick Vaccaro
Turn on power for front camera at startup in coreboot (needs to be set for factory scan). BUG=b:69011806 BRANCH=master TEST=none Change-Id: I2f31b19dfef5fe386b485dd675f0ff981288acf4 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/23503 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-30mainboard/google/zoombini/variant/meowth: fix SPD issuesNick Vaccaro
Fix incorrect settings in the Hynix 4GB and Samsung 2GB SPD files for meowth. BUG=b:69011806 BRANCH=none TEST=Confirm meowth with Hynix 16GB and meowth with Samsung 8GB solutions boot. Change-Id: Ia2ac564541b57647c3b605ce3389d74251490ca0 Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23388 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-30mainboard/google/zoombini/variants/meowth: enable I2C bus #2Nick Vaccaro
Enable I2C #2 for display backlight controller. BUG=b:69011806 BRANCH=none TEST=none Change-Id: I5440bd4265414c55458a73e293a9931145a158cc Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23392 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-01-30mainboard/google/zoombini/variants/meowth: Add rev 2 gpio changesNick Vaccaro
Change GPIO settings for meowth rev 2 boards. Changes include: - GPP_B7 set to no-connect - GPP_C1 set to no-connect - GPP_D8 set to no-connect - GPP_D9 (PP3300_WLAN_EN) set as output with initial value high - GPP_E9 (DCI_CLK) set to no-connect - GPP_E10 (DCI_DATA) set to no-connect BUG=b:72202352 BRANCH=none TEST=none Change-Id: I2e6d049faaa0a70b40ceb47aaf81a81d820dd4c1 Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23391 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-30mainboard/google/zoombini/variants/meowth: Fix USB OC settingsNick Vaccaro
Set USB2 port 0 & 1 to use OC2 and OC3 respectively. Previous settings were causing false overcurrent conditions as OC0 and OC1 were used for other purposes. Remove initialization of unused usb3 ports, and configure the ports we use (usb3 ports 0 & 1) to use OC2 and OC3, respectively. BUG=b:72250084 BRANCH=none TEST=Verify meowth can recognize and boot off a kernel on USB drive. Change-Id: I528b67d80a1da84e5307facb40de545089979f57 Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23390 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-30mb/google/poppy/variants/soraka: Update _PSV for TCPUFurquan Shaikh
This change updates the passive setting for TCPU as per factory team recommendation. BUG=b:65467566 Change-Id: I081f63bdf811ff021c398f60efec9e6cccf462d5 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23494 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-30mb/google/poppy/variants/soraka: Enable mode-aware DPTFFurquan Shaikh
This change selects EC tablet event and provides trip point temperatures for tablet and non-tablet mode so that DPTF can be supported depending upon device mode. BUG=b:65467566 TEST=Verified by changing modes that the trip point temperatures are updated in the OS (/sys/devices/virtual/thermal/thermal_zone{2,3,4,5}). Change-Id: I071868982fa87821550b870a6d8050cf2a030b49 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23463 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2018-01-30chromeec: Decouple EC tablet event and TBMC deviceFurquan Shaikh
This change decouples EC tablet event and TBMC device by guarding TBMC definition and notification using EC_ENABLE_TBMC_DEVICE. It allows mainboards to use tablet events without having to define a TBMC device. BUG=b:72554519 Change-Id: Ie38b6d68486e8e644dd0d6d406def3ae7fdb5152 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23461 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2018-01-30mb/google/kahlee: correct comments in baseboard gpio.cAaron Durbin
The gpios for 147 and 148 are connected to PCH_I2C_HUB_SCL and PCH_I2C_H1_TPM_SDA, respectively. Fix the comment. BUG=b:64140392 Change-Id: Ibebf6ce7d9fb26276b12b9c9844c260413f0337e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/23499 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-01-30mb/google/kahlee: mark h1 bus as early init for gruntAaron Durbin
Since the h1 i2c bus is required for verstage mark the bus as needing to be initialized early. That way, the bus is initialized in bootblock prior to verstage. BUG=b:70232394,b:69250772 Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/23498 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-01-29google/scarlet: Add initialization sequence for Innolux P097PFG panelLin Huang
Innolux didn't deliver a working init sequence yet for devices without OTP programming. The sequence in this change has been derived from a register dump of a mostly working panel with OTP. It is not meant to be final, but to make devices with unprogrammed OTP work, while Innolux is figuring out a proper sequence. There is a known issue with an artifact line in the lower third of the display. Change-Id: I7096506208e4cb29c5f31a7ac502231a6c23ac92 Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-on: https://review.coreboot.org/23311 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-01-29rockchip/rk3399: Support LONG_WRITE type in MIPI DSILin Huang
Some panels need to transfer initial code, and some of them will be over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi dsi transfer function to support it. Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-on: https://review.coreboot.org/23299 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-01-29google/fizz: Adjust PL2 and PsysPl2 values for power lossShelley Chen
Set PsysPl2 values to 90% of max adapter power for all types of adapters (typeC and barrel jack) to account for a 10% power loss from the adapter to the soc. BUG=b:71594855 BRANCH=None TEST=reboot device and make sure Pl2 and PsysPl2 MSRs are properly set with iotools rdmsr command on both U42 and U22 skus with both typeC and barrel jack power adapters. Change-Id: I8425c6d4d669449eccb9324ff58ff6d1662c5c43 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/23457 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-01-29mb/google/kahlee: Fix I2C bus 1 timing for GruntJustin TerAvest
I measured the rise and fall times for I2C bus 1 from userspace manually, using "i2cdetect 1" called from userspace and an oscilloscope. This commit fixes the values there to reflect reality. BUG=b:72442912,b:70232394 Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23459 Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Chris Ching <chingcodes@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-26mb/*/*/cmos.layout: Fix the values for the console levelArthur Heymans
Fix the values that were off by one. This was discovered when using postcar stage that prints with debuglevel BIOS_NEVER. Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/23186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-01-26mb/google/poppy/variants/soraka: Configure unused pins as NCFurquan Shaikh
This change configures unused pins as not connected. Change-Id: I6779d9fba73da8fb2faa08ad5d2236b813105720 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23416 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-26mb/google/poppy/variants/nautilus: Update camera power enable GPIOsFurquan Shaikh
This change updates the camera power enable GPIOs as per the latest schematics. With this update, since one of the enable GPIOs is using a UART0 pin, set UART0 to PchSerialIoSkipInit in devicetree so that FSP-S does not re-configure the UART0 GPIOs. BUG=b:68964831 Change-Id: I5d9126ed8ca2b714f6276f4d3a24c243d7654774 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/23414 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-26mainboard/google/zoombini/variant/meowth: add PCH_WP_ODNick Vaccaro
Configure GPP_H12 as an input for PCH_WP_OD. BUG=b:72202352 BRANCH=none TEST=none Change-Id: Ie5b60644a24d745add4d0d38c1421974b8a0017b Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org> Reviewed-on: https://review.coreboot.org/23389 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-25mb/google/kahlee: Add Grunt touchscreen supportJustin TerAvest
This commit adds support for an Elan touchscreen device connected over I2C via devicetree. BUG=b:72121803 TEST=Confirm the device is probed for. Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23408 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-01-25mb/google/kahlee: Add Grunt devicetree i2c bus cfgJustin TerAvest
I2C bus configuration is generally set up in devicetree.cb. This change establishes listings for the buses so that they can be used (though followup changes should update the buses to have correct timings). BUG=b:72121803 Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23407 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-01-25mb/google/kahlee: Select DRIVERS_I2C_GENERICJustin TerAvest
This is required to add support for I2C devices on Kahlee to ACPI tables via devicetree.cb. Without this, operations are not emitted for I2C devices and the proper ACPI table entries are not generated. BUG=b:72121803 Change-Id: I1cfe12f3cc23e90ec74b739678f5a5a73257c2c2 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23406 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-01-25mb/google/kahlee: Correct grunt HWID in GBBJustin TerAvest
Chrome OS reports that "GRUNT TEST XXXX" is an invalid hwid. The 8296 comes from the lower four numbers from running: $ printf "%d\n" 0x$(crc32 <(echo -n 'GRUNT TEST')) BUG=b:72436450 Change-Id: Ib0044442396cad65c25c107feb35a30a2f70b769 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/23411 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2018-01-25mb/google/poppy/variants/nami: Disable SATAKane Chen
This change disables SATA controller in order to make SATA IP enter low power status. BUG=b:72332817 TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status and verify SATA IP enters low power state Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f Signed-off-by: Kane Chen <kane.chen@intel.com> Reviewed-on: https://review.coreboot.org/23354 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-01-25mainboard/google/zoombini: add ACPI entry for cr50Caveh Jalali
This adds coreboot device tree entries on zoombini & meowth for the cr50. Also, fixes the GPIO pin IRQ settings to be falling edge. This is based on what we do for fizz. BUG=b:71722449 TEST=booted to linux on meowth: tpm_version command now sees the cr50. localhost ~ # tpm_version TPM 2.0 Version Info: Chip Version: 2.0.0.0 Spec Family: 322e3000 Spec Family String: 2.0 Spec Level: 0 Spec Revision: 116 Manufacturer Info: 43524f53 Manufacturer String: CROS Vendor ID: xCG fTPM TPM Model: 00000001 Firmware Version: 0ad551830bcf7a82 localhost ~ # uname -a Linux localhost 4.14.13 #3 SMP PREEMPT Sat Jan 13 02:55:45 PST 2018 x86_64 Genuine Intel(R) CPU 0000 @ 1.00GHz GenuineIntel GNU/Linux localhost ~ # and we see interrupts when talking to the cr50: localhost ~ # grep cr50 /proc/interrupts ; tpm_version ; grep cr50 /proc/interru pts 84: 4687 IO-APIC 84-edge cr50_spi TPM 2.0 Version Info: Chip Version: 2.0.0.0 Spec Family: 322e3000 Spec Family String: 2.0 Spec Level: 0 Spec Revision: 116 Manufacturer Info: 43524f53 Manufacturer String: CROS Vendor ID: xCG fTPM TPM Model: 00000001 Firmware Version: 0ad551830bcf7a82 84: 4799 IO-APIC 84-edge cr50_spi localhost ~ # Change-Id: I9d503334502503ef49515e4a8736d967bc454a98 Signed-off-by: Caveh Jalali <caveh@google.com> Reviewed-on: https://review.coreboot.org/23310 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-03 02:43:19 +0000