| Age | Commit message (Collapse) | Author |
|---|
|
In case where PAD_CFG_GPI_INT() is initialized with a pin value
lower to PAD_CFG_GPI_IRQ_WAKE() for same GPIO community
the set_ioapic_used() is only called for the PAD_CFG_GPI_IRQ_WAKE() pin.
Due to this the IRQ associated with PAD_CFG_GPI_INT() is found free by
find_free_unique_irq() during IRQ assignment and assigned to other pins
which causes IRQ conflicts
BUG=b:322984217
BRANCH=None
TEST=Boot test on brox, check if correct IRQ assigned to EC
Change-Id: I8c3d557e888b8d0ceac203f49b702910fba26d6d
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80334
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Upload initial GPIO configuration for xol based on proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
xol proto board can boot to ChromeOS
Change-Id: I224e58628e44571c07ce034136d690587e62be08
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80325
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Upload the initial devicetree and update Kconfig for xol following
proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot
Change-Id: I411932eb4872d77993394a290e8afdd1a0038faf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80324
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update the I2C configuration to match the usage such that only required
I2C controllers are enabled.
BUG=b:319390850
TEST=Build Brox BIOS image and boot to OS. Ensure that only the required
I2C controllers are enabled.
Change-Id: I9f24beb9ef587163362cc6ded88efb05be1329b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80303
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow reference design rex0, keep the GPIO settings of CNVi/PCIe.
Only set GPP_F04,GPP_F05/GPP_S01,GPP_S02 to NC when
WIFI_PCIE/WIFI_CNVI is selected.
BUG=none
TEST=Build and test on karis
Change-Id: Id23a2cfe0639f2d423980db9badc16c1477434d1
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Update element "KB_TYPE_CA" for align fw_config.
Only EC will reference KB_TYPE field in fw_config. This
CL is just for align fw_config.
BUG=none
TEST=emerge coreboot pass
Change-Id: Ied54f78dddd9dddca1272fc31c9502fc11c61dde
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
|
|
On Brox, HDA Codec used is ALC256. Add verb table for the same. Also,
add the related device tree changes for HDA related registers.
Realtek High Definition Audio Configuration-
Version : 5.0.3.1
BUG=b:317398558
BRANCH=None
TEST=verified HDA on Brox.
HDA Sound cards detected. Headphone working verified.
Device listed under sysfs as below:
cat /sys/bus/hdaudio/devices/ehdaudio0D0/chip_name
ID 256
cat /sys/bus/hdaudio/devices/ehdaudio0D0/vendor_name
Realtek
Change-Id: I1edd5aee053debe39b34048266703031c088cd00
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79723
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
GPP_E08 and GPP_E22 were set incorrectly previously.
This CL corrects these settings according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I8e427350e1ee564f9d6566bdfe1f42c92c87a711
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
With Cr50, the GPIO EC_IN_RW is used to determine whether EC is trusted. However, With the switch to Ti50, it is determined by Ti50's boot mode. If the boot mode is TRUSTED_RO, the VB2_CONTEXT_EC_TRUSTED flag will be set in check_boot_mode(). Therefore in the Ti50 case get_ec_is_trusted() can just return 0.
The current code of get_ec_is_trusted() only checks the GPIO, which
causes the EC to be always considered "trusted". Therefore, correct the return value to 0 for TPM_GOOGLE_TI50.
BUG=b:321172119
TEST=emerge-nissa coreboot chromeos-bootimage
TEST=firmware_DevMode passed in FAFT test
Change-Id: I308f8b36411030911c4421d80827fc49ff325a1b
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp- partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add RAM ID for
H58G66BK7BX067 0 (0000)
BUG=b:322528721
BRANCH=firmware-rex-15709.B
TEST=Run part_id_gen tool without any errors
Change-Id: I31538988d1329d9e2f45d862eb0ae05c0d6a179e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Check MTL EDS2, SOC_TCHSCR_RST(GPP_C01) default setting is NF1.
Set SOC_TCHSCR_RST to output low in early_gpio_table.
BUG=none
TEST=Build and test on karis, touchscreen function works
Change-Id: Ieebd3cf3c320bc895d036c372f792ec7b5d7ebf9
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Follow reference design rex0, toggles NVMe PWR pin as soon as
in early stage to make NVMe ready sooner.
BUG=none
TEST=Build karis and try warm reboot from OS console. Check the DUT
with WD SSD boots to OS again.
Change-Id: I24a702f02278355c4f2137f0d05c8a9da7cb3c1c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80213
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current panel voltage measured at mainboard side is 1.79V and the
voltage at panel side is 1.74V. Since the panel requires 1.8V or more,
increase the circuit voltage to 1.9V to meet the panel requirement.
After adjustment mainboard side voltage is 1.89V and panel side is
1.84V.
BUG=b:322080023
TEST=Check ciri vm18 ldo voltage
BRANCH=None
Change-Id: I6d6193d45409f53c0b656890c44ddaef253c5e01
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80198
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI_SCI_IRQ is defined as 9 for all AMD SoCs, so move the definition to
the common amdblocks/acpi.h. Since all but Stoneyridge's soc/acpi.h are
now empty, delete those files too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8210c98dc4cf2c6001d5273d132053278ff7fea5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80222
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables Cnvi BT Audio Offload feature and also
configures the virtual GPIO for CNVi Bluetooth I2S pads.
BUG=b:303157827
TEST=Build and boot to anraggar. Verify the config from serial logs.
w/o this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 0
[SPEW ] Pin Muxing
```
w/ this CL -
```
[SPEW ] -- CNVi Config --
[SPEW ] CNVi Mode= 1
[SPEW ] Wi-Fi Core= 1
[SPEW ] BT Core= 1
[SPEW ] BT Audio Offload= 1
[SPEW ] Pin Muxing
```
Change-Id: I9e6731c8ceaad6ee58b525d4246fa769bfe1b0c7
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80001
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add WIFI SAR table for omniknight.
BUG=b:320172979
TEST=FW_NAME=omnigul emerge-brya coreboot
Change-Id: I70e79577612b3d5c4dc0f92211f87cbea0532d5d
Signed-off-by: jamie_chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80152
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch ensures the baseboard and variant configs (inside Kconfig
and Kconfig.name) are organized in alphabetic order.
TEST=execute make menuconfig and verify the google/rex variants
order are alphabetically correct.
Change-Id: I0acc2cec21b4607856127b04c400ec416f0c0dd2
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80206
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the new memory support:
Samsung K4U6E3S4AB-MGCL
BUG=b:320137193
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go JSL lp4x \
src/mainboard/google/dedede/variants/galtic/memory/ \
src/mainboard/google/dedede/variants/galtic/memory/\
mem_parts_used.txt"
Change-Id: I3f6c784a194e141a3dd1e5a37b3cf12106e692d6
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80150
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
BUG=b:300690448,b:319393777
BRANCH=None
TEST=tested on a device with i2cdetect
Also tested with evtest and make sure Wacom is listed
Change-Id: I4f528b0d778c8c4a4e83774d5c167ccb2d6afd9a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79895
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is causing an assertion error on the devices that don't have CNVi
enabled because CNVi is hidden behind a FW_CONFIG flag in the
overridetree now.
BUG=b:319188820
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure we can boot to kernel on device.
Change-Id: Ifcfbc04825d4d4e7f2874a4c52f9c5cf3e657856
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80211
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Alphabetize the ordering of model configs and selects in Kconfig and
Kconfig.name
BUG=None
BRANCH=None
TEST='emerge-brya coreboot' and verify it builds.
Change-Id: Id9347421337d451ce72fcf3984489b06f372f70c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This change eliminates the unnecessary override of the tcc_offset
chip configuration to 10, as the default rex baseboard now handles
this setting correctly.
TEST=Successfully built and booted google/karis, confirming tcc_offset
remains at 10.
Change-Id: Ie40db1431fb0197ee360ad5656878e57f51c855b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow thermal team request, override tcc_offset to 20.
TEST=Build and verified by thermal team using google/screebo.
Change-Id: Idc76f9c0054f21f066b779e6404a1c175eb396a0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This CL update setting according to schematic v0.4.
BUG=b:320201111
BRANCH=firmware-rex-15709.B
TEST=Built FW image correctly.
Change-Id: Ia4570d26ee9fd175ed9099bd057cee3c30c95704
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80156
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Some variants added the generic gfx driver with an LCD device without
specifying the address, which is required for the backlight controls
to be functional under Windows. Add the address value where missing.
Address value used (0x80010400) is same as on other Brya variants which
did properly set it, and is taken from the ACPI 6.5 spec section B.4.2,
_DOD (display output device enumeration), table B-2:
- bit 31 = use the ACPI-defined (vs vendor-defined) bit scheme for bits
15-0
- bit 16 = platform firmware can detect the device
- bit 10 = display type is internal/integrated flat panel (aka LCD)
TEST=build/boot Win11 on google/brya (osiris), verify ACPI backlight
controls functional.
Change-Id: Id24e330cfb7c993d12665a704e1ca78e2e38874f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
and amplifier
Compatible headphone codec "ALC5682I-VS" and speaker amplifier "ALC1015Q-VB"
BUG=b:183305590
TEST=ALC5682I-VD and ALC1015Q-VB can work normally
Change-Id: I4f212f063a1180d7a1c14769f61b0afef7565cad
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79831
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Endeavour and Karma were missing, leading those devices to have empty
SMBIOS mainboard names. Fix by adding the missing entries.
TEST=build/boot google/fizz (endeavour), verify SMBIOS name correctly
shown via dmidecode.
Change-Id: I1d4fb2473d27ff5611f9d2b962aae2d6bf6d1da0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80181
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was a mistake in the gpio spreadsheet provided by the HW team
and the GPIO assignments for the EC INT and WAKE signals got switched
from what it was in the schematics. The correct assignments are:
GPP_D0 = EC_PCH_INT_ODL
GPP_D1 = EC_PCH_WAKE_ODL
BUG=b:311450057,b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Will try to boot OS image on device and see if there are any
ec errors.
Change-Id: I02057aeb5d82218dbbe4c939d4feb87a4d3da678
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79886
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new i2c address 0x24 of touch IC for Parade touch panel.
BUG=b:320731709
Test=emerge-nissa coreboot
Change-Id: I51bd89beffd912fc147da11d19f38cb44cbe570a
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Now that the files are renamed, make sure all references to Makefile.inc
are updated as well.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I09e235eecf0c32c80a41bfcbbd3580cce6555e10
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib8a2ae26ed4380592d15e1a7b2d682639413af01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I85cda24aa7dec82d23e8a321dac03ec737f4c503
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80108
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I92f8bd7e1c9fc6e4120fb94c2299a266304e19de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80107
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I134acc26c0a79d974a6dd0a3b257f961db7e2d86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80106
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature for rex.
BUG=b:270664854
TEST=Build, boot and test on rex with value under sysfs
/sys/bus/pci/devices/0000:00:04.0/tcc_offset_degree_celsius
Change-Id: I9012984016ab3213102214025d6d8dc07c5d8974
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79992
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Peter Ou <peter.ou@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I5855f49984db59d786decad6142e3525b146a573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80105
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
We need to disable the cnvi device when pcie wifi is enabled, so need
to use the FW_CONFIG defined in the overridetree for this.
BUG=b:311450057,b:300690448,b:319188820
BRANCH=None
TEST=This will be tested on the device when received
Change-Id: If9e861db37e321fd69c09f9b4aafa2e212f92caa
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79898
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:311450057,b:300690448,b:319188820
BRANCH=None
TEST=test on device with lspci
& make sure can see the Intel Network controller
Change-Id: I361bef13ebd073b6fccb729a1960d3832cf2681a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Create the xol variant of the brya0 reference board by copying the
template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:319506033
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_XOL
Change-Id: Id60c50b70c9ab53d62ad48cfc15462f2410f9f02
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80145
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Repo sync code recently, run command as memtioned in TEST and
found the changed for the auto-gen files.
Then correct the memory typo from K4UBE3D4AA-MGCR to K4U6E3S4AA-MGCR,
and no new for the used hex file.
BUG=b:320181366
BRANCH=firmware-dedede-13606.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go JSL lp4x \
src/mainboard/google/dedede/variants/galtic/memory/ \
src/mainboard/google/dedede/variants/galtic/memory/\
mem_parts_used.txt"
Change-Id: I7c158eb7b4455cde839a335913e6a18895c12b41
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79976
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Split the SOC_AMD_PHOENIX Kconfig option into SOC_AMD_PHOENIX_BASE that
selects the non-FSP-specific options and SOC_AMD_PHOENIX_FSP that
selects both SOC_AMD_PHOENIX_BASE and the FSP-specific options. This
will help to separate the FSP-specific from the FSP-agnostic code. The
mainboards using this SoC now select SOC_AMD_PHOENIX_FSP instead of
SOC_AMD_PHOENIX.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5e95fbfd9d16930ba3e6cc497557d61adba5a6fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79983
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add get_wifi_sar_cbfs_filename(). This function uses the FW_CONFIG
for WIFI to choose the right wifi_sar hex file. Below is the file
mapping:
wifi_sar_0.hex = wifi6
wifi_sar_1.hex = wifi7
BUG=b:319302319
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
Change-Id: I212c80412141e7770a512bd8ccf4111963bab395
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80085
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Primus4es board is no longer supported thus drop it from the tree.
TEST=Build all Brya boards in CrOS-SDK - Primus4ES not built. No negative impact observed.
Change-Id: I0502b2eed6f80d648b422c8d1622d504a6c93822
Signed-off-by: Jakub Czapiga <czapiga@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
1. Describe the FW_CONFIG probe for the settings for Palutena.
- WIFI_SAR_ID_0 for AW Wi-Fi module AW-CM421NF
- WIFI_SAR_ID_1 for Intel Wi-Fi module AX211NGW
2. In contrast to the AW Wi-Fi module, the Intel Wi-Fi module needs
to load a SAR table in dedede platform.
3. For Palutena project, the SKU ID segment of Palutena is set for
"0x350000~0x35FFFF".
BUG=b:319792428
BRANCH=firmware-dedede-13606.B
TEST=build pass
Change-Id: Ic4f38928d24c4398d90df226cfe0788a30075bf2
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79930
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
|
|
Add 6w and 15w fan performance control.
BUG=b:318454915
TEST=emerge-nissa coreboot chromeos-bootimage
Thermal team test pass.
Change-Id: If21baa2f6f9bcd527cec2bced27c5fb2cd607830
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79988
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Modify 6w/15w DPTF parameters based on b:290705146#comment41.
2. 6W MSR power limit_1 power (Watts) increase to 20.
3. 15W MSR power limit_1 power (Watts) increase to 20.
BUG=b:290705146
TEST=emerge-nissa coreboot chromeos-bootimage
Thermal team test pass.
Change-Id: I15fa4b8f7c7088ff56da6493659ae45572913b5a
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
I got confused and used UFS (User Facing Side) for the User Facing
Camera (UFC) in the FW_CONFIGs. Change references of the camera from
UFS --> UFC.
BUG=b:300690448
BRANCH=None
TEST=None. The camera has not been enabled yet.
Change-Id: I4f8240ae51aad1e077f325a9eab5a2a92f1402cb
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79997
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous.
Built all variants with BUILD_TIMELESS=1 and the resulting binaries
remain the same.
Change-Id: I22bcde2dea726f47f8d64a762ca147efde0b610d
Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
to 6ms
Modify touchscreen enable_delay to 6ms to meet with spec.
eKTH3915N_Product Spec_V1.3_20221028_IPM.pdf
BUG=b:318443640
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: Id57ab04e61d9e95c962f2c564d3a7e2e7ed6b992
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79978
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
Gothrax cannot boot into OS with a kernel loading failure.
Update eMMC DLL values to improve initialization reliability
How to get these values:
- Sending different speed TX/RX command/data signal to eMMC and check
the response is successful or not.
- Collecting above results from each eMMC model that project used.
- Analysing logs to provide a fine tuned DLL values.
BUG=b:310701323
TEST=Cold reboot stress test over 2500 cycles
Change-Id: Ie36cc9948e3d5dee46385e584baad141a249be79
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
These are specific to the brox board, so moving devices to the brox
variant.
BUG=b:311450057,b:300690448,b:319058143
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
will check if this helps detect the storage device in the factory
Change-Id: I18d096040c293abfd4cd0b1bb5f50ba6dcc2e183
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Brox project has FW_CONFIG bits already set up in the project file for
the retimer and for storage, so make sure that the brox device tree
matches those settings.
BUG=b:311450057,b:300690448,b:319058143
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
will check if this helps detect the storage device in the factory
Change-Id: Iaf43003b7e8210eee9016d779839d7048c15825f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79854
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory Micron MT62F1G32D4DR-031 WT:B.
DRAM Part Name ID to assign
MT62F1G32D4DR-031 WT:B 2 (0010)
BUG=b:319778218
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I9e54958490228beb7039d531c709d56ec244b9e7
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79914
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The IVO_T109NW41 will be the second source MIPI panel for Ciri.
BUG=b:319025360
TEST=boot Ciri with IVO_T109NW41 panel, see firmware screen
BRANCH=None
Change-Id: I9dc2228d39bb8bb048d1f37727c96b0ad621e912
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
The MIPI panel BOE_NV110WUM_L60 will be used for Ciri, enable it.
Also remove the `mdelay(10)` after mtk_i2c_bus_init, because MTK
confirms this is not needed. Add mdelay(2) between VDD18 and VSP/VSN
to meet the panel datasheet.
BUG=b:308968270
TEST=Boot to firmware screen
BRANCH=None
Change-Id: I0a04f062f81c543d38716d7ff185b5633c1aa3a9
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78957
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I09dd5871cb366ef95410efc1ca6c4337f23b52fd
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79912
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
BUG=b:311450057,b:300690448
BRANCH=None
TEST=to be tested on a device with i2cdetect
Change-Id: If6da1c722e87a50c6d422b300f16a52d884fa08f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This is needed for NVMe to work when PCIe device is connected to the
CPU side of RPL soc.
BUG=b:311450057,b:300690448, b:319058143
BRANCH=None
TEST=Tested on device and was able to boot to the OS
Change-Id: Ic8a1fdcedf2ec6c7bf1dd00e02ef7c13e9338aac
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This needs to be disabled for RPL otherwise we'll hit the assertion:
[EMERG] ASSERTION ERROR: file 'src/soc/intel/alderlake/fsp_params.c', line 1066
There is a comment in the referenced file/line in the assertion that
says that "C state demotion must be disabled for Raptorlake J0 and Q0
SKUs." So, disabling it.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=Tested that we didn't hit this assertion on the device after this
change
Change-Id: Ib7b2484de2d84c980550fd951f1e30efab0ee197
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79855
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.In contrast to the MediaTek Wi-Fi module, the Intel Wi-Fi module needs
to load a SAR table.
2.Describe the FW_CONFIG probe for the settings.
- WIFI_6 for MTK Wi-Fi module MT7921L
- WIFI_6E for Intel Wi-Fi module AX211NGW
BUG=b:315418153
TEST=emerge-nissa coreboot
Change-Id: I37e8adc3de02707b2df541cc5e6f88083554eeb4
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
driver
Since DRIVERS_I2C_SX9324_SUPPORT_LEGACY_LINUX_DRIVER value on dedede
cannot meet DRIVERS_I2C_SX9324 on nissa, need to update the tuning
value. Update proximity sensor fine tune value with quandiso EVT
machine.
BUG=b:314550601
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot and verify p-sensor
watch 'cat /sys/bus/iio/devices/iio:device*/*raw'
Change-Id: I5fc3bc5876594f2df79d628bd986113d37087c3d
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add PIXA touchpad for variants of craaskov.
BUG=b:289962540
TEST=build craaskov firmware and test with PIXA touchpad
Change-Id: Iccf19b275548f44aec00be8631590b8a7ad1aa23
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79872
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Removes unnecessary HAVE_FSP_LOGO_SUPPORT config from google/rex
baseboard. Intel Meteor Lake SoC now selects this config
automatically for supported platforms.
BRANCH=firmware-rex-15709.B
TEST=Able to build and boot google/rex and intel/mtlrvp.
Change-Id: I89bdd54cb73b11f74db2927a5eb86ab826c60517
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79860
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to some without mipi camera SKUs can't entering S0i3.
BUG=b:317670018
TEST=suspend_stress_test -c 1
Change-Id: Ifa8649a603c59946b530abd315113b405ceaf35a
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This partially reverts commit f493857c9bc1 ("mb/google/brya/var/*: Set
dGPU/LAN/WLAN device type to generic"). Setting the WLAN device type to
generic broke ACPI SSDT table definition, so set it back to pci.
BUG=b:318576073
TEST=build/boot google/nissa (pujjo), verify WLAN ACPI SSDT tables
contain the appropriate device entry.
Change-Id: If5dad9deb040c8cb0c507e11726f0ba44ccb2909
Signed-off-by: David Ruth <druth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
TEST=check FW screen on dojo
Change-Id: Ie870899226588ac2a2e80f77e434455f4913d387
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
TEST=check FW screen on Steelix, Tentacruel and Starmie
Change-Id: I429218d59389a6ab86b522dd597c07fa5b8ea821
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79777
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The sequences of configure_display() are similar on MediaTek platforms.
The sequences usually involve following steps:
1. Setup mtcmos for display hardware block.
- mtcmos_display_power_on()
- mtcmos_protect_display_bus()
2. Configure backlight pins
3. Power on the panel
- It also powers on the bridge in MIPI DSI to eDP case.
4. General initialization for DDP(display data path)
5. Initialize eDP/MIPI DSI accordingly,
- For eDP path, it calls mtk_edp_init() to get edid from the panel
and initializes eDP driver.
- For MIPI DSI path, the edid is retrieved either from the bridge or
from CBFS (the serializable data), and then initializes DSI driver.
6. Set framebuffer bits per pixel
7. Setup DDP mode
8. Setup panel orientation
This patch extracts geralt/display.c to mediatek/common/display.c and
refactors `struct panel_description` to generalize the display init
sequences. configure_display() is also renamed to mtk_display_init().
TEST=check FW screen on geralt.
Change-Id: I403bba8a826de5f3fb2ea96a5403725ff194164f
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79776
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DQS mapping for DIMM idx 6 was discovered to be incorrect to what
was in the schematics. Correcting the mistake in this CL.
BUG=b:311450057,b:300690448
BRANCH=None
TEST=tested on device and it passed memory training
Change-Id: I21f50e2f5b4fae09725c1c7532636ed1cc1a9043
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79843
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
For brya variants with a touchscreen, drive the enable GPIO high
starting in romstage while holding in reset, then disable the reset
GPIO in ramstage (done in the baseboard).
BUG=b:317746281
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I3ca2e2d12a86eaae9e37870a2541c0287e354690
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79764
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To avoid code duplication and to also bring the mainboards using the
Picasso SoC more in line with Cezanne and newer, factor out the SoC-
specific code from the mainboard's dsdt.asl files to the SoC's soc.asl.
TEST=Timeless builds result in identical images for Bilby, Mandolin, and
Zork/Morphius
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id4ed3a3d3cb55c8b3b474c66a7c1700e24fe908e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips
initial probe during kernel boot, preventing privacy LED blink.
BUG=b:317434358
TEST=none
Change-Id: I43044e64c2c3a645ec0cad2ac903cc19ac89c9af
Signed-off-by: Jason Chen <jason.z.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79803
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Built all variants with BUILD_TIMELESS=1 and the resulting binaries
remain the same.
Change-Id: I7752819091e2a75c8d818f7d0cf90eabc11c4759
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Marvin Evers <marvin.evers@stud.hs-bochum.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
1. Set PCIe related GPIOs to NC if fw_config use "WIFI_CNVI".
2. Set CNVi related GPIOs to NC if fw_config use "WIFI_PCIE".
3. Remove "ALC5650_NO_AMP_I2S" case in
fw_config_gpio_padbased_override(). bt_i2s_enable_pads should not
relevant to audio codec/amp, and it is already enabled in "WIFI_CNVI"
case.
BUG=b:312099281
TEST=Build and test on karis
Change-Id: Ib1a32f1a38ae33cf992b80a3408aa8e2fa3ddab0
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79765
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add touchscreen ILTK for craaskwell.
Refer to ILI2901A-A200 Data Sheet_V1.1_20231026.
BUG=b:308873706
TEST=build and check touchscreen function on craask
Change-Id: I6a68855b1659ff0c9cd33a0ec9acbd289f525a3d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79735
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
|
|
Create the dita variant of the taranza project by
copying the files to a new directory named for the variant.
BUG=b:317292413
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DITA
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I843e33f30cd356e4f12330bdfe2d53a0b3920ef3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79655
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
As a preparation for WiFi SAR table addition, adding hook for it.
BRANCH=nissa
BUG=b:315418153
TEST=emerge-nissa coreboot
Cq-Depend: chrome-internal:6790137
Change-Id: Idb200699bb8c8581b9512ec8ec9442f65f8822b3
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add GFX devices for DDI (eDP and HDMI) and TCP (USC C0 and C2
ports). Copied the PLD placements from USB PLDs.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: Ic39916819f64ede1c80eccfd05ba4916b9f285af
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Update definition to be more intuitive and extensible.
Port descriptors will be defined as individual entities and added
to the descriptor list as such.
BUG=b:281059446
TEST=builds
Change-Id: I23ddd11b7e4da35a0d81299aa648f928e81ea24e
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79626
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update definition to be more intuitive and extensible.
Port descriptors will be defined as individual entities and added
to the descriptor list as such.
BUG=b:281059446
TEST=builds
Change-Id: Ic5a06a7d1bdb9123a0a242a571f094ac3233d7b2
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79627
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This is a preparation to make the next patch result in identical images
for timeless builds and also aligns Zork's DSDT more with Guybrush's
DSDT.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46835b404be13f150c68680afb3fcc78639e08f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
update DTT settings for thermal control,the values before
Sensor1 and Sensor2 were set too high. Modify the protection
temperature to better meet DUT requirements.
BUG=b:291217859
BRANCH=none
TEST=emerge-rex coreboot
Change-Id: I8abc866c0d05a2437c34198e6b8fb4a58c1cb829
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79683
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
According to datasheet, EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high
should over 5ms. And current measure result is 200us.
Set EN_TCHSCR_PWR to output high in bootblock to make it meet datasheet
requirment.
Measurement result of EN_TCHSCR_PWR high --> SOC_TCHSCR_RST_R_L high:
Power on --> 31.7 ms
Resume --> 38.7 ms
BUG=b:314245238
TEST=Measure the sequence
Change-Id: I56e455a980b465f27794b30df058ec0944befc2e
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79571
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add probe DB_C_A_LTE/DB_C_A for Type-C Port C1 (daughter board).
DB_A is only used for skus without Type-C Port C1.
BUG=b:316048649
TEST=emerge-nissa coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ifb702c497740953144b43c56653da16fade1053f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79629
Reviewed-by: Kyle Lin <kylelinck@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Some GPIOs were not configured correctly according to the HW
spreadsheet provided by the HW team.
* GPP_B5/GPP_B6 use NF1, not NF2
* GPP_B23 should use NF2, no GPI
* GPP_D11 should be set to NC
* GPP_E21/22 should be using NF (previous NC)
* GPP_F17 is a GPO
* GPP_F18 should be an interrupt, not a NF
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I9e1e62adb79bd7fdab935afdbf2d23f9061b88aa
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL are to fix the pad's reset field
as needed. See "Intel SoCs" section in
https://doc.coreboot.org/getting_started/gpio.html for reset
definitions.
BUG=b:300690448,b:316180020
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4285136184c648adb9dc97748bd6b01cba3f8ddd
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79579
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes in this CL include fixing the pulls for
GPIOs as necessary, making sure that it matches what is in the HW
team's spreadsheet.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: Ie50cb3c6fc85f1633c1afd1330c0e040e04b0ec1
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79704
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Did a pass through HW team's brox speadsheet and aligned the gpio.c
file with it. The changes here include changing the pad config to NC
because it is not being used in ChromeOS.
BUG=b:300690448
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I15471e4d7ff25c858b05ef024f15ca7c0b9e598e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79703
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add HDMI GPIO configuration to early GPIO list to support
VGA text o/p in Pre-RAM stage on HDMI.
BUG=b:316982707
TEST=Erase MRC cache and reboot, SOL text display on HDMI/eDP
Change-Id: Idb2af56baeb4d0ef9db5fc1c5dbcebecee6515e6
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79572
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Since the camera sensor and camera eeprom share GPP_A12, remove
the off timing to avoid issue of camera sensor loss, but this
will increase system power by 5mW.
(Before root cause, this is a short term workaround to unblock
function test.)
BUG=b:298126852
TEST=1. Run coldreboot/warmreboot check see if the camera sensor lost.
2. Run S0ix check to see if the camera function abnormal.
Change-Id: I49b6ecbfbf3dddd6575bdaaf9c8fd0ee6c09af25
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79647
Reviewed-by: Jason Z Chen <jason.z.chen@intel.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
|
|
set slew rate to 1/8 for GT domain.
BUG=b:312405633
BRANCH=none
TEST=Able to build and boot google/screebo
Change-Id: Ib5cb07b7effc4a51c2119183010a03e026f639f8
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
|
|
Some of the boards use the EC_SYNC pin to wake the AP but do not
advertise the pin as wake capable in the CREC _CRS resource. Relevant
boards were determined through empirical testing and inspection of gpio
configuration.
Update the ACPI tables for rex, brya, and brox based boards to advertise
their EC_SYNC pin as wake capable.
BUG=b:243700486
TEST=-Dump ACPI and verify ExclusiveAndWake share type is set when
EC_SYNC_IRQ_WAKE_CAPABLE is defined
-Wake Aviko via keypress and verify chromeos-ec as wake source
-Wake Screebo via lid open and verify chromeos-ec as wake source
Change-Id: I5828be7c9420cab6ae838272c8301c302a3e078c
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79374
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
FSP default value for LpDdrDqDqsReTraining is 1. For boards
that didn't set LpDdrDqDqsReTraining to any value, 0 was being
assigned and it caused black screen issue.
BUG=b:311450057
BRANCH=NONE
TEST=emerge-brox coreboot
Change-Id: I4a009076e50408a4f7ff16ddc96a0f2e47b09470
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79646
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
GPP_B02 and GPP_B03 were set incorrectly previously.
This CL corrects these settings according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Id62f15f7a77ac43c72cc6b2645816d6c87133a0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Only EC will use field "PANEL_PWRSEQ_EC_CONTROL".
Add this field in coreboot for align fw_config settings.
BUG=b:314245238
TEST=emerge coreboot pass
Change-Id: Icecb44a338ddc28027e362332c6a69cc9fd268d5
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79570
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After confirm with thermal, only EC will reference FAN field in
fw_config.
Update the settings for align fw_config.
BUG=b:307822225
TEST=emerge coreboot pass
Change-Id: Id7c4cdba29c5500c06d0f2293495650bb14b9e9c
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79573
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
|
|
Use same indent levels for switch/case in order to comply with the
linter.
Change-Id: I602cf024ec84b15b783d36014c725826f9d6595e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79418
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Acoustic noise mitigation for google/screebo and set slew rate
to 1/8 for IA domain and ignore the slew rate for SA domain.
BUG=b:312405633,
TEST=Able to build and boot google/screebo.
Before:
[SPEW ] AcousticNoiseMitigation : 0x0
[SPEW ] FastPkgCRampDisable for Index = 0 : 0x0
[SPEW ] SlowSlewRate for Index = 0 : 0x0
After:
[SPEW ] AcousticNoiseMitigation : 0x1
[SPEW ] FastPkgCRampDisable for Index = 0 : 0x1
[SPEW ] SlowSlewRate for Index = 0 : 0x2
Change-Id: Ib86939ab48c2c6e7d0491d7c1cb4a2c7c6a1b568
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79323
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
