Age | Commit message (Collapse) | Author |
|
"is_wakeup_source" flag is used to indicate if the concerned device can
trigger a wakeup. This flag is redundant with the "wake" GPE event
definition. So remove the redundant flag and use the "wake" GPE event to
mark the wakeup source.
BUG=None
BRANCH=None
TEST=Boot to ChromeOS. Ensure that the device is marked as wakeup-source
in SSDT if wake GPE is configured. Ensure that the system can suspend
and the device acts as a wakeup source
Change-Id: I99237323639df1cb72e3a81bcfed869900a2eefa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
See Documentation/coding_style.md, specifically "Placing Braces and
Spaces" section.
Change-Id: Ia6a2f3d3547c16500996260b0ece9ec693f00113
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ibb7ce42588510dc5ffb04c950c4c8c64e9a2fa37
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables I2C bus 2, 3 and 4 in devicetree and configures
GPIO pads for the same. It also configures pads for I2C5 as
no-connect.
BUG=b:123711244
TEST=Verified that i2c shows up in "i2cdetect -l" after booting to OS.
Change-Id: Ib4714a670d73228332115415e4393f82802c6475
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31237
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current coreboot size is not adequate for adding new features.
Note for cros: This change is for merge to ToT only and should not be
cherry-picked into reef's firmware branch.
BUG=chromium:903833
TEST=emerge-reef coreboot
Change-Id: Ie7a25c4638c474e81fb34b57de0dfc1bf393ea67
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds keyboard backlight feature for Hatch platform.
BUG=b:122799544
BRANCH=none
TEST=keyboard backlight works when EC reports correct info.
Change-Id: I29273122f061e0e442f6629351ef3670535c0507
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31175
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reconfigures the GPP_D1 GPIO pin as a no-connect. It really
doesn't go anywhere today or on previous revs of the board.
BUG=b:110614620
BRANCH=none
TEST=atlas still boots
Change-Id: Iea53cf909f8f060c4e0f14e8b4ad579b838b7caa
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 7696290004b6490c7ef8027d7ddf67b163e7dad8.
We're seeing trackpad problems on some units with the I2C bus running
at 1MHz but not at 400KHz. So, revert back to 400KHz until we
understand how to make 1MHz operation more robust.
BUG=b:123650686
Change-Id: Ifb06afece9eee0c153240d35e6c3001f5b74f310
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The default value for Chrome OS HWID should be different.
Calculated as HWID v1.
BUG=b:123336677
BRANCH=kukui
TEST=build and boots properly.
Change-Id: I39c640562c1c3b117292b8abacd36a4a9c2fa6c6
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This change enables exporting the reset GPIO for CNVi Bluetooth module to
the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS. Checked the SSDT table to ensure that the reset
gpio is exported under the device \_SB_.PCI0.XHCI.RHUB.HS09. Ensured
that the kernel btusb driver is able to find the exported GPIO in the
devices with CNVi BT module.
Change-Id: I10f28bfe705da5104d709ae2ed91a8ae003fa639
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This implementation adds support to create ACPI package for USB port
capability (_UPC) and physical location of device (_PLD) for USB2 port 10.
BUG:b:123375275
TEST:Verify _UPC and _PLD ACPI packages gets published for USB2 Port 10
in SSDT and BT is functional in discrete and integrated mode.
Change-Id: Ifeab24505a700e8e4677be20074c7d0400769cec
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/31197
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:123540469
BRANCH=None
TEST=None
Change-Id: I713e6ad70efdd152895afa45aee44a5b53a8136b
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31157
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable USB ACPI driver for octopus boards and add bluetooth USB ACPI
configuration in devicetree. This change enables exporting the bluetooth
reset GPIO to the kernel for use in an rf-kill operation.
BUG=b:123296264
BRANCH=octopus
TEST=Boots to ChromeOS
Change-Id: Ie40f1ad70f21a6fd398ce23d060e0c588ba6ce41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/31130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In payloads, we didn't set GPIO modes. We have to set up GPIO mode in
coreboot for payloads.
BUG=b:80501386
BRANCH=none
TEST=HW reboot works in depthcharge
Change-Id: Ibd2c6c071871edc59497fbb245cdbec6a814f621
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31148
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove hard coding for SaGv config in devicetree.cb and apply macro for
SaGv config for CNL variants boards
Change-Id: If007589d5c1368602928b1550ec8788e65f70c05
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
After adjustment on Arcada EVT
TouchScreen: 390 KHz
TouchPad: 389 KHz
H1: 389 KHz
BUG=b:120584026, b:120584561
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia6eb332e7a664b211a5025ad07e0d01bf7f8d5bb
Reviewed-on: https://review.coreboot.org/c/31124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Real unused GPIO pad is GPIO_123, but GPIO_122 is configured as unused pad.
This patch corrects the configuration.
BUG=NONE
BRANCH=octopus
TEST=emerge-octopus coreboot
Change-Id: I4473bd66a4162f5aee3b998aacba906824728fc8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Initialize EC_PCH_WAKE_ODL GPIO to make sure that ec events will wake
the AP from suspend. Also create a task to initialize the hostevent
wake mask properly.
BUG=b:123325238,b:123325720
BRANCH=None
TEST=from AP console: powerd_dbus_suspend
from EC console: hostevent (make sure wake mask set)
from EC console: gpioset PCH_WAKE_L 0
Make sure device wakes up
Also, checked to make sure keyboard press wakes up
device from S3.
Change-Id: I53d5291a6b9ab9a21e89ccd21f172180ce473bd5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
List Raydium touchscreen in the devicetree so that the correct ACPI device
are created.
BUG=b:121105424
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
reflash the coreboot to DUT, make sure the Raydium touchscreen can work.
Change-Id: I9ffb2a858f31a8b003086806de07f4079870cddf
Signed-off-by: Hao He <hao.he@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31116
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL moves some initialization steps from bootblock to verstage. This
will save us about 2700 bytes (before compression) / 1024 bytes (after
LZ4 compression) in bootblock. In case of CONFIG_VBOOT is disabled,
these initialization steps will be done in romstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I9968d88c54283ef334d1ab975086d4adb3363bd6
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Asserting GPIO PERIPHERAL_EN8 will send a signal to EC to trigger a HW
reset for SoC and H1.
BUG=b:80501386
BRANCH=none
TEST=emerge-kukui coreboot; manually verified the do_board_reset() on
Kukui P1
Change-Id: I9afad84af2031a766bc08fc76c8b5f55588c453a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31118
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Separate WDT reset function from WDT driver, then we can use the common
WDT driver and have a board-specific reset function on different boards.
In Kukui, we plan to use GPIO HW reset, instead of WDT reset. Add config
"MISSING_BOARD_RESET" in Kukui to pass the build for now.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot;
Change-Id: Ica07fe3a027cd7e9eb6d10202c3ef3ed7bea00c2
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31121
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These pins should not have pull downs configured in standby state as that
can cause contention on the termination circuitry and lead to incorrect
behavior as per Doc# 572688 Gemini Lake Processor GPIOTermination
Configuration.
BUG=b:79982669
TEST=Checked that code compiles with changes.
Change-Id: If3cadc000ec6fc56019ee3f57e556dc819d5e0a5
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/c/30823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
ELAN touchpad supports up to 400KHz, so we need to limit its CLK
frequency to 400HKz.
BUG=b:123376618
BRANCH=octopus
TEST=built and verified touchpad I2C clk frequency gets be lower than 400KHz
Change-Id: If7a43fe20c7e5abdf23c8c36e34c072c371563bf
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/31085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
New emmc DLL values for Ampton
BUG=b:122307153
TEST=Boot to OS on 5 systems
Change-Id: Iadd58d254f4bb384f483c2c3e5615f7569d5211c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add support Synaptics touch pad for Aleena/Kasumi.
BUG=b:122549449
BRANCH=master
TEST= Check if synaptics touch pad working in ChromeOS.
Change-Id: Icab1b312f1943b27037ef458044ce9e7172919ee
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31064
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
need it
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set tcc offset value to 5 degree celsius for Sarien system.
BRANCH=None
BUG=b:122636962
TEST=Built and tested on Sarien system
Change-Id: I06fbf6a0810028458bdd28d0d8a4e3b645f279ca
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable gpio_keys driver for bobba and add required configuration in the
device tree to handle the pen eject event.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus tools
open on pen eject. Ensure that the system wakes on Pen Eject. Ensure that
the system enters S0ix and S3 states after the pen is ejected. Ensure that
the system enters S0ix and S3 states when the pen remains inserted in its
holder. Ensured that the system does not wake when the pen is inserted.
Ensure that the suspend_stress_test runs successfully for 25 iterations
with the pen placed in its holder.
Change-Id: I768b89d2b45f4dcab6d235b11ce00544a827f22d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
This CL adds a new function mt8183_early_init, which includes all
initializations that should be done in early stages. All mainboards
using MT8183 should manually call it in either bootblock or verstage.
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I35d7ab875395da913b967ae1f7b72359be3e744a
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/31024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch enables relevant GPIOs to enable WWAN. WWAN also requires to
enable USB 2 port 6 and USB3 port 5 which is already enabled in device
tree related changes.
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I1559bbc6168aec1a369bf3291d2c1e2f9a2fbe07
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable PCIe WLAN for hatch
1. Enable PCI port 14 for PCIe WLAN
2. Enable CLKREQ, CLK SRC 3 for PCI port 14
3. GPIO pad config for WLAN and BT
USB port for BT has already been enabled so not included in this patch
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I4f2a6eb37a467ad8b8cdde8fe6b657fabb383b04
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
With the memory controller the separate sockets becomes a useless
distinction. They all used the same code anyway.
UNTESTED: This also updates autoport.
Change-Id: I044d434a5b8fca75db9eb193c7ffc60f3c78212b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31031
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace B0D4 with TCPU for DPTF thermal sensor. This helps to
maintain consistency between coreboot and UEFI BIOS.
Change-Id: I024068c19160e1c08badef3d304ada14455c045f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31028
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a merely cosmetic change.
Change-Id: If36419fbee9628b591116604bf32fe00a4f08c17
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/31030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Kukui with vboot enabled will build with `detachable_ui`, which needs
larger space in CBFS for more complicated assets. So we need to revise
FMAP sections:
- BOOTBLOCK (not really used) only needs <= 32K.
- GBB can be much smaller since assets moved from GBB to CBFS.
- FMAP is re-ordered (with the cost of less efficient in bsearch) so CBFS can
get larger continuous space.
- COREBOOT(CBFS) should take all space left.
Since FMAP and COREBOOT have changed location, the system will need to
reflash EC (which contains the new bootblock) as well.
BUG=b:123202015
TEST=Builds and boots on Kukui P1
Change-Id: I22cff99dca8c396c5897c3f6631721af40f3ffbd
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
disable unused usb2 ports of bard and ekko skus
BUG=120874946
TEST=build a test firmware and run lsusb to check usb ports
Change-Id: I2ef3cd17ada8b65c96bc80675650905949f235e1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30986
Reviewed-by: Vincent Wang <vwang@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for arcada platform, the slow slew rates
are fast time dived by 2.
BUG=none
BRANCH=none
TEST=none
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia838818a76a7f638b24146f3eb48493a4091c9cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31034
Reviewed-on: https://review.coreboot.org/c/31034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
BUG=b:80501386
BRANCH=none
TEST=Boots correctly and stress test pass on Kukui.
Change-Id: I985c5061ce4ed4d88a17619aa5cde7d0121dd3a3
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/31033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
close the FP module power in power off (s5)
BUG=122887366
BRANCH=Nami
TEST= build test firmware and measure the fp power enable pin
Change-Id: I80ddfbf1edf7c6435d263d5f5e0edb8b8701817d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30910
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable support for SD card support for hatch
1. Enable PCI device for SD and also configure SD detect GPIO
2. Configure SD card related GPIOs in gpio.c
BUG=b:120914069
BRANCH=none
TEST=Verify GPIO configuration with schematics
Change-Id: I8ccaa28323b1e1fcc192e245347a96309227660b
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
New emmc DLL values for Meep.
BUG=b:122308271
TEST=Boot to OS on 13 Meep system
Change-Id: I4247114ed69ff3aa283f0f72d5531ad0f37309ad
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/31021
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 3278f859c3dd97a6d6d885a91dfd33d44e95d58b.
Reason for revert:
It turns out all we want to set in RAM stage is GPIO's DEBOUNCE config,
not its SCI configuration.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Boot grunt, does not go to recovery screen
Change-Id: I500934f3e03e66c97873accd4a979a23d4509675
Reviewed-on: https://review.coreboot.org/c/30997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
hatch shouldn't make use of internal ec.bin through IFD tool.
Change-Id: Ib1a324291b1c8ac90a7d790b63427b2e85c74fd1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Some usb devices exhibits signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BRANCH=octopus
BUG=b:120009029
TEST=Verified usb operation successfully.
Change-Id: Ic7fa08c894397598dee3c4ff9a764e43383a0627
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Some usb devices exhibit signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BUG=b:122671995
TEST=check "Disable Link Compliance Mode" bit of "SuperSpeed Port Link
control" register and usb operation successfully.
Change-Id: Ia2ae7e52391fadc8ed23b8b76c45d410757d22ec
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/30948
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add available thermal sensors information for CPU throttling action.
BRANCH=None
BUG=b:120058043
TEST=Built and tested on Arcada system
Change-Id: I748ca0ce43915c96d71e63fb03fc3d1a02adc56c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After adjustment on Sarien EVT
TouchScreen: 380.7 KHz
TouchPad: 379.3 KHz
H1: 392.2 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I0dd92b054d934b38a17898dc8ce9cc18bda1633f
Reviewed-on: https://review.coreboot.org/c/30949
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
set SaGv = SaGv_Enabled , To Enable System Agent dynamic frequency support
set HeciEnabled = 1, To Enable heci communication
set speed_shift_enable = 1 To Enable Speed Shift Technology support
Change-Id: Iea90a65a77ef5e45a802cfe6fd31e1921163b02b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Change-Id: If336e9d7016987be151ab30d5c037ead3a998fe0
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
BUG=b:122578255
BRANCH=None
TEST=mosys platform id/name/family
Change-Id: I6288ea1a4e9f692b6e04440e61f59ea53f01ebec
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Disabling software sync since EC patches haven't landed yet.
BUG=b:120914069
BRANCH=None
TEST=build bios image and make sure gbb flag 0x200 is set
Change-Id: I1661bcd6ebbee6d9aa8068efcc18b259fb4c8203
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change tcc offset from 15 to 3 for sarien.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: I1c5d144e92d1e6e9c81b3e6686805ccf744b7203
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30808
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The general rule is to configure GPIOs used by coreboot in bootblock
(using the reset table), and GPIOs used by OS in RAM stage.
However, GPIO_9 will be used as both, and we need to reconfigure it to
properly set up debounce, however, it is no longer possible to change
bootblock, so we also configure it in RAM stage to make the new
debounce configuration take affect.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Reboot stress test grunt (>100 times); no messages in dmesg like:
tpm tpm0: Timeout waiting for TPM ready
Change-Id: I0f1bca176ed3f9cebf6b9e9e1008905e492a2f03
Reviewed-on: https://review.coreboot.org/c/30922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I299a584ef2ba66d1e752515100cbe3919b2108f6
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30726
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I2593afa69cfb955f6a2b695406855e0f31f28468
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30725
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: Ic6678d3455f1116e7e67a67b465a79df020b2399
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Accoding to desciption in FSP header, Vref Configuration will be set to
2 if VREF_CA to CH_A and VREF_DQ_B to CH_B.
BUG=N/A
TEST=Build and boot up on Arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I02e16e141b81d766a6060ca08283f432abd96647
Reviewed-on: https://review.coreboot.org/c/30280
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable at24 EEPROM by adding ASL of nvm
BUG=b:122583978
BRANCH=master
TEST=Build and run for basic camera functions
Change-Id: Ifc2060c2ceb7d1a8ef490f36f484deb425a37c95
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/30795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Change-Id: I41ad1ce06d9afcc99941affa232fa76ffa6631fb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts commit 4e3cd744492c7a3d80bca55a35276efeada731e5.
Reason for revert: Daisuke says "We'll keep EFS on Kalista/Karma enabled"
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I2f11ffc9dd7eb05a2560261bbf472e8488c274d9
Reviewed-on: https://review.coreboot.org/c/30857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Invert the default instead of selecting it everywhere. Restores the
ability to use its Kconfig prompt.
Beside Qemu targets, the only platforms that didn't select it seem
to be samsung/exynos5420, intel/cannonlake, and intel/icelake. The
latter two were about to be patched anyway.
Change-Id: I7c5b671b7dddb5c6535c97c2cbb5f5053909dc64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30891
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch revises the pad reset config of speaker reset GPIO pin from
RSMRST to PLTRST. Audio engineer suggested to reset the amps with
warm reset.
BUG=b:122441567
BRANCH=None
TEST=warm & cold reset & suspend_stress_test -c 10 and ensure the
speakers are working well.
Change-Id: I87c554b186b068da93e1662a97afaf01dddae0ef
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
PLT_RST_L was asserted twice at boot-up and a glitch was observed
when coming out of suspend mode. Configure PLT_RST_L pad IOSSTATE
from HIZCRx1 to be masked.
BRANCH=octopus
BUG=b:117302959
TEST=Verified no glitch on PLT_RST_L at S3 and PLT_RST_L stays high
3.3v during S0ix.
Change-Id: I8c23aadda72be54fb45e67aab2bc8ed51e473bae
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30815
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some usb devices exhibits signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BRANCH=octopus
BUG=b:115699781
TEST=Verified usb operation successfully.
Change-Id: I41fecaa43f4b1588a0e4bbfc465d595feb54dd24
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30817
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Integrated BT controller in CnVi uses USB port 10 for communication.
BUG=b:122552619
TEST=lsusb shows BT device
Change-Id: Iad1ca0e9419b534f50a3ce3fdcbd660caf8efb5c
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30809
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
butterfly is a Sandybridge device, and selecting Ivybridge
breaks libgfxinit currently due to CPU mismatch
Test: build/boot butterfly w/libgfxinit
Change-Id: I1a7f5a3681d21a256834b11b545855c4365f5f78
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30820
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required for functional internal display on butterfly using libgfxinit.
Test: boot/build butterfly, verify internal display functional
prior to OS driver loading.
Change-Id: Ib8060f2d1ad0694f0886d35c83763907f61b47b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30819
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add placeholder for future flapjack additions/modifications.
BUG=None
BRANCH=kukui
TEST=build with kukui/flapjack configurations
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: Ib9cd39e284f19b9179da73ed9f2b13d97442960e
Reviewed-on: https://review.coreboot.org/c/30859
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Enable the EC_AP_INT_ODL interrupt on GPIO_134 for all octopus boards
that support it. Also removing unnecessary IO standby support since we
don't use this pin to wake up the SoC.
BRANCH=octopus
BUG=b:122552125,b:120679547
TEST=CTS tests with changes
Change-Id: I018864ae5fa400372b5b443e49828e8202b9aa4d
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30788
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most boards currently do not use EC firmware from SPI flash in the
IFD, this hides this option by default and shows it only for boards
that need it.
A new config variable MAINBOARD_USES_IFD_EC_REGION is introduced to
enable this option for boards that need it.
The following list of boards requiring this was provided by
Lijian Zhao:
1. intel/cannonlake_rvp
2. intel/coffeelake_rvp
3. intel/icelake_rvp
4. google/sarien
5. google/hatch
Change-Id: I52ab977319d99a23a5e982cc01479fe801e172a7
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Kukui is going to use ADC#4 as SKU ID, and utilizing EC BoardID as
global board_id (i.e., board revision).
BUG=b:122060615
TEST=make; manually tested on Kukui P1 board.
Change-Id: I7bba368c141a7ba6db11f24b8e8e7158f0fc729e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The ID from ADC on Kukui supports 16 different values and we should list
all voltage values ahead.
BUG=b:80501386
TEST=make; manually verified on Kukui P1
Change-Id: Ic3abe07abfe818ca68e180c262fd431d1167b801
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
From `boardid.h`, the uninitialized ID values should be BOARD_ID_INIT
instead of BOARD_ID_UNKNOWN.
BUG=b:80501386
TEST=make; manually verified on Kukui P1
Change-Id: Ie5267e575e38b92ec64a7317defbd00ee153fa0a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
1) Add a Platform Data Region called SI_PDR which is allocated in the flash
descriptor for this platform
2) Add a DIAG_NVRAM region for use by the diagnostic payload for non-volatile
storage.
3) Encapsulate both RW_LEGACY and DIAG_NVRAM in a region called RW_DIAG
so it is clear they are associated.
4) Move the RW_DIAG region to the start of the RW region so that once we can
re-enable a larger BIOS region this sub-region will be in the uncached area
since it is not accessed on a normal boot.
BUG=b:119435206
TEST=tested on Arcada board to ensure expected regions are present
Change-Id: Ieb8bc4cf70d0a931e4944210112cfaf5c543f9f3
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Change-Id: I28c67fbdf2b4f371c4b533b64cad2c4376ca2bd2
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30785
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sdram config sdram-lpddr3-hynix-4GB.inc for H9CCNNNBKTMLBR-NTD can't
boot on Mickey. It's confirmed that the right config for Hynix
H9CCNNNBKTMLBR-NTD is sdram-lpddr3-hynix-2GB-BK.inc.
BUG=b:122239609
BRANCH=master
TEST=boot on mickey
Change-Id: Ifeaadda50d939e0c118cb7fe3964dcd08b709c2a
Signed-off-by: Loop_Wu <Loop_Wu@asus.com>
Reviewed-on: https://review.coreboot.org/c/30761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch disables the SA IPU for hatch since it is
not using the IPU.
Change-Id: Ib2afc4cc4fd7ef98365b0b98130b0e8bc757ac2a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Reading nvdata from non-volatile flash storage. With this patch, it will
pass the firmware test that corrupts FW_MAIN_A and boots up with
FW_MAIN_B.
BUG=b:80501386
BRANCH=none
Test=test_that --board=kukui 172.23.213.147 firmware_CorruptFwSigA
Change-Id: I9ef6bff019ee986ff018202bfd4d4a875526ec6c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/30701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:119899987
TEST=build and flash to rammus, log into rammus and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Signed-off-by: marxwang <marx.wang@intel.com>
Change-Id: Ieadb3609c7634a20e96c7c4dfb96f5e3f23e468b
Reviewed-on: https://review.coreboot.org/c/30607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify ELAN touchpad bus i2c clk from 466Khz to 400Khz.
BUG=b:119628524
BRANCH=master
TEST=measure ELAN Touchpad CLK
Change-Id: Ia8433c6ef320cea9a0145db4ba440d67ccd0f41e
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30588
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The vbt was extracted from the option rom found on stock images.
The vbt.bin is the same across all variants.
The VBT has a modified BDB block 43, the 'Backlight info block' such
that the inverter type for the panel in use is set to
2 (BDB_BACKLIGHT_TYPE_PWM) instead of 0 (BDB_BACKLIGHT_TYPE_NONE).
This only seems to matter on Windows, as without it changing the
backlight duty cycle does not work.
Change-Id: I82c72c561e1058e0b77d80baf330b64f7c6b08e3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30487
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|