| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
This patch removes IccMax settings from device tree since they
are handled in SoC code from patch e1a75d.
BUG=b:71369428
BRANCH=None
TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot
chromeos-bootimage" & ensure the IccMax settings passed
to FSP are from SoC code.
Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Turn on the load switch to the FP MCU at startup, so the kernel can
detect it and use it.
The load switch enable pin is connected to the GPP_A11 PCH pin (aka
PCH_FP_PWR_EN).
BRANCH=none
BUG=b:71986991
TEST=on Meowth, see the kernel detecting a cros_fp device at startup:
[ 2.133456] cros-ec-spi spi-PRP0001:00: Fingerprint MCU detected.
[ 2.157420] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Change-Id: Id3c40b965a5f018c63481c2e2eea3fc8307352bd
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure the FP MCU interface on GSPI1.
BRANCH=none
BUG=b:71986991
TEST=boot on reworked Meowth with a ZerbleBarn board attached to
GSPI1 and see the cros_ec kernel driver detecting it.
Change-Id: Ib874ddaf4948a766fd05c11f4675dbfdb679059d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for new memory stuffing options that will appear on
the P1 meowth boards.
new strap setting - associated SPD file
----------------------------------------
0b001 - Hynix_H9HCNNN8KUMLHR_1GB.spd.hex
0b010 - Samsung_K4F6E3S4HM_2GB.spd.hex
0b011 - Hynix_H9HCNNNCPUMLHR_4GB.spd.hex
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: Ief07f3de351d01cbc195b785c36e96de0cbf7ddb
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Rename tlcl* to tss* as tpm software stack layer.
* Fix inconsistent naming.
Change-Id: I206dd6a32dbd303a6d4d987e424407ebf5c518fa
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Our current U22 skus (celeron and i3) actually don't support PL2,
but making sure that if we do decide in the future to use it to
make sure PL2 and PsysPl2 values are set appropriately.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 90W with barrel jack for U42
and 65W with barrel jack for U22.
Change-Id: I084d0320128a6e05948023520a30c497c41be23b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
Change-Id: I65173104fce258d03956bbb0e80073c47fe80fab
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
* Add IMX258 sensor entity
* Add DW9807 VCM control entity
* Enable CIO2 and IMGu in devicetree.cb
TEST: Verified the MIPI camera function on DUT board
Change-Id: Iebd41ac3631829bbb0b008761eb67c3db3e94638
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Right now the poppy baseboard camera topology allows to add maximum of 2
sensors. The sensors can be of different vendors. The current ASL code
structure doesn't allow sensor customization. Moving PMIC specific objects
from sensor objects to PMIC scope and having separate sensor ASL files will
help in unbinding the PMIC and sensor objects and allow some customizations.
BUG=None
BRANCH=None
TEST=Build and boot soraka, make sure both camera's are working fine
and also verify that the generated DSDT looks fine.
Change-Id: I63ae1a685b78bda212c5c48a4c2dc744164a3cb5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
The variant boards can have a custom endpoints, splitting the ASL code
aids customizing the endpoints as per the variant board setup.
BUG=None
BRANCH=None
TEST=build boot soraka, verify that the cameras are working fine and
generated DSDT tables are same as before.
Change-Id: I5f1cded25bfb6a7baf18b211f9773dfecdc2f264
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
BUG=b:71838954
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. check touchpad function
3. evtest
/dev/input/event5: Elan Touchpad
Change-Id: I14471d1473a3b3ecf15aaf362b47874704cd3bf0
Signed-off-by: van_chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/23133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIOs that are being set low had the wrong value getting set.
FCH_GPIO_OUTPUT_VALUE was being set instead of FCH_GPIO_OUTPUT_ENABLE.
BUG=b:70234300
TEST=Build and boot Grunt
Change-Id: I16792b76252506a43aac92738b04096ae3fde01c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Grunt and Kahlee touchpads are on different i2c busses; I2CC and I2CD,
respectively.
Since grunt is the 'baseboard', put its configuration under baseboard, and
include it from the grunt variant.
BUG=b:71820409
TEST=Boot grunt to kernel, use evtest to test trackpad.
TEST=Boot kahlee to kernel, use evtest to test trackpad.
Change-Id: I1aeacf9a840342e73c1e219a825b39a124b4dd57
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23232
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Grunt and Kahlee have different audio codecs.
Create a new audio .asl for the baseboard for grunt's codec, link
to it from the grunt mainboard, and move the kahlee codec table
from the baseboard mainboard to its own .asl in variant/kahlee.
Note, we can't use the generic drivers due to the PCI scope
expectation. The AMD I2C are not PCI devices.
BUG=b:69397774
TEST=Codec driver loads. Check dmesg.
Change-Id: I1cc245357d1f3d444e5a5012466eaa5d75d637eb
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/23226
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the apci/ to the baseboard and move mainboard.asl to
each variant.
BUG=b:71873651
TEST=build
BRANCH=none
Change-Id: I8a829f2946e4b280cd78574eb8dbda6c2a9a1028
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23229
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Meowth uses GPD_2 as a dedicated lan_wake pin, so GPD_2 must
be set to use NF1 instead of gpio.
BUG=b:64395641
BRANCH=none
TEST=none
Change-Id: Iadf7158a792dfae0ea5e824d197a558524cdb5fd
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change PAD_CFG_GPI_GPIO_DRIVE to PAD_CFG_GPI_APIC for GPIO D9 to
meet the requirement of DA7219 IRQ pin.
BUG=b:70646770
BRANCH=none
TEST=Use aplay and arecord to verify headphone function.
Change-Id: Id6cff8325c4c7f02f6f4df547fde286e2ef83d5c
Signed-off-by: Kaiyen Chang <kaiyen.chang@intel.com>
Reviewed-on: https://review.coreboot.org/23160
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TCPU:
_CRT: 100
_PSV: 93
_TRT: 100/5(s)
TSR0:
_CRT: 83
_PSV: 70
_TRT: 100/10(s)
TSR1:
_CRT: 73
_PSV: 67
_TRT: 100/30(s)
TCC: 6 for 94'C
PL1:
max: 15W
min: 3W
BUG=b:70294260
BRANCH=master
TEST=build
Change-Id: Ie17f4395d2199009fd68a600d818f2be54bc8935
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/23155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fizz has external Lan on PCIE port.
The Lan device on PCH is not used.
BUG=b:70889517
Change-Id: I99894bedec14a44724ac7c22d0c894132a795b78
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Digitizer power is not controlled by SoC. Also, since the digitizer
uses I2C-HID driver in Linux kernel, the device is put into sleep
anytime system is suspended. Thus, there is no need to control the
reset gpio using ACPI power resource.
TEST=Verified that digitizer device is properly detected on boot-up
and after suspend/resume.
Change-Id: Id11b8412d0ac48b2701d53b0a22ad3b747b544ec
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- Add pen device property into devicetree.cb.
- Set GPP_C9 to 0 as default.
BUG=none
BRANCH=master
TEST=emerge-nautilus coreboot and check pen device operation
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I050671c8b46fd92b1dd9164be2646727cd67da9f
Reviewed-on: https://review.coreboot.org/23010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Port initializer had been changed from PortDisabled to PortEnabled,
but engine inializer hadn't been updated from PcieUnusedEngine to
PciePortEngine. Update this so the port works.
Also change disabled port to PcieUnusedEngine.
BUG=b:71818026
TEST=PCIe device now shows up on D2F4
Change-Id: I11eb8c1fbad12fa9cf34d758a4ef3c22ef8ba4f7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23210
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If using type-C charger, then PsysPl2 may be lower than barrel jack
value of 90W, so need to override value to the max power of type-C
charger.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 60W with zinger, but 90W
when using proper barrel jack adapter on and i7.
Change-Id: If955b9af0e23f47719f001f1d73ec37113937cea
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:64395641
BRANCH=none
TEST=none
Change-Id: I92969384cd32766be4595494aa70b4eb9c74f099
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
-add initialization of gpio table to mainboard_silicon_init_params()
-fix input parameter type for mainboard_silicon_init_params() for
FSP2_0.
BUG=b:69011806
BRANCH=chromeos-2016.05
TEST=none
Change-Id: If8cba786a127a8704eb240380841362e3eb06552
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Map EC io space in devicetree.cb
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: Ic3806b5f9b7bf272a77360060cd71db9a03d5763
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:69011806
BRANCH=chromeos-2016.05
TEST=Compiles successfully using "./util/abuild/abuild -p none
-t google/zoombini -x -a"
Change-Id: I8276fa26af664557e9964cb6b8a5a076eacdf00c
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
-add ec.c to bootblock if CONFIG_EC_GOOGLE_CHROMEEC
-add ramstage.c to ramstage.
BUG=b:69011806
BRANCH=chromeos-2016.05
TEST='emerge-meowth coreboot' compiles correctly.
Change-Id: I7ec1e22339f3e4d9a8d83093bcc2ce725c9c99e7
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
-change GPP_C12 (H1 IRQ) to use GPI_SCI_LOW and level triggered
-set gspi gpios to no connects if CONFIG_ZOOMBINI_USE_SPI_TPM not set
BUG=b:69011806
BRANCH=chromeos-2016.05
TEST='emerge-meowth coreboot' succeeds
Change-Id: Ida1d1050db12982c3c497656162cc84c62a77f70
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
-add USB2 and USB3 to devicetree
-add TPM_TIS_ACPI_INTERRUPT to Kconfig
-map gpe0_dw0, gpe0_dw1, and gpe0_dw2 blocks
BUG=b:64395641
BRANCH=chromeos-2016.05
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: Ia7ed76591d9d8d94bbf5652313c478495ce005fa
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spd.bin file was not getting generated properly, so moved logic
to variant's makefile.
BUG=b:64395641
BRANCH=none
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully and spd.bin is found when booting.
Change-Id: I4642d6ddb5e65f721d1bde31ca0ca5b4438da554
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The .spd.hex text is added to the name by the build process. This
was causing a failure because we were trying to add the files:
'file.spd.hex.spd.hex' to the build.
Remove the additional .spd.hex text.
BUG=b:71535311
TEST=Build
Change-Id: I11df7a90c979503676a66c6502900a13f1a8e359
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23189
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
|
|
turn off SATA SALP to prevent 0x5A/0x5B error on Sandisk SSD
in below conditions:
1. reboot stress
2. FAFT BIOS qualification
BUG=b:70146894,b:69984821,b:70590720
BRANCH=master
TEST=pass firmware_ConsecutiveBoot 2500 loops
FAFT BIOS test pass
Change-Id: I5d57dd8ef256d5f0a1027ab77f63da62c6c9ce74
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/23153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add Meowth board, which derives from Zoombini, a CNL reference board.
BUG=b:69011806
BRANCH=master
TEST=Compiles successfully using "./util/abuild/abuild -p none
-t google/zoombini -x -a" and boots Meowth.
CQ-DEPEND=CL:22908
Change-Id: Ie6ed7ebb4a00a87fc93fc694d74c08a716380a54
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/22401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure
that required SPD hex files are included in the SPD binary.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I449ab56dfc7a75752944b58ba6291b5ee32f81ad
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/22205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Since the current hardware revision does not have external pull on the
pen eject signal, this change adds internal pull-up on it.
Change-Id: I426d9833d7efbd8735b6f2b4896d1012b62cb4b8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tony Lin <tonycwlin@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Rainier, a scarlet derived board, was configured to use spi0 for tpm
driver by default. This patch switches it to spi2 to reflect recent
changes in scarlet-derived boards.
Change-Id: Ib67109786512c068bb957890f456bccff7addc86
Signed-off-by: Ege Mihmanli <egemih@google.com>
Reviewed-on: https://review.coreboot.org/23129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I417a1c606e4968120414af57aa3b17d5c3b3cad0
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Enable I2C #2, #3, and #5
- Enable UART #2
- Enable GSPI #0 and #1
- Disable SATA
- Set pci 1f.0 to chromeec
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: Ie29652beff36f19a59746a1ad5f8e7f995ef1281
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add mainboard.c to ramstage.
BUG=b:64395641
BRANCH=None
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: Ic7275b07f28a99a91b978d2e8c4118c6858705bc
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Grunt's devicetree dropped some entries when it was split from the
kahlee variant. This commit restores:
spd_addr_lookup - memory information for AGESA
dram_clear_on_reset - keeps DRAM contents on reset
uma_mode - needed for vbios
uma_size - needed for vbios
Change-Id: I1d8cdc97594867f1d706318370055087976a5104
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The spd size of DDR4 is 512, but the size empty.spd.hex is 256.
With empty.spd.hex and DDR4, it will cause mainboard_get_spd_data
loads spd data incorrectly due to the offset is wrong.
Change-Id: Iea3f216898525a2a602fabf1835c8a0c1245ee57
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change is to enable SataPwrOptEnable.
With this change, we no longer see SError message in kernel during
suspend_stress_test.
BUG=b:70491485
Change-Id: Ieb991f6889c5ff3181a670bc7702314049fa983c
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch revises LED0 Green light behavior from patch 2ecf3f8c.
For 100Mb link speed, LED0 should be OFF.
BUG=b:65437780, b:68284778, b:69950854, b:65808944
BRANCH=None
TEST=Run DUT with 100Mb and 1000Mb ethernet connection and observe
LED0 is behaving as expected.
Change-Id: Ia805c955711b8ce77eba087a28427a005c456fa1
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22964
Reviewed-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
firmware test team is requesting that default gbb flags set to 0x39
rather than 0x239 so that it's consistent with the default gbb flags
of other platforms.
BUG=b:70392534
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage
gbb_utility --get --flags image-fizz.bin and make sure
that it returns 0x39 instead of 0x239
Change-Id: Ib73e4619b13f6b7c2d01598c926fbbd7d7eb9bef
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22962
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable S0ix for fizz.
BUG=b:67598361
BRANCH=None
TEST=None. Need to be tested with EC and kernel as well.
Change-Id: I981d2cc7e969a44567b0f21f63f68c78e73f5cb5
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/22955
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Don't rely on the cascading default values. Ensure Kahlee uses the fanless
versions of the SMU fimware by selecting it.
Change-Id: I0761266f2a4026ebc251b64074c10481118734a2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
There is a potential IMVP8 issue for KBL that affects Intersil VRs
Fizz is using one of the affected parts. The fix is to use an updated
microcode and also send a mailbox box command from FSP.
BUG=b:65499724
BRANCH=None
TEST=Build and boot Fizz
Change-Id: Iebfda02df88ea0d2aaf79e8449b95c0eb2165c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/22763
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to pass USB2 eye diagram, some USB2 port PHY registers
needs to be changed.
Port1 (Type-A): USB2_PORT_SHORT
Port2 (BT): USB2_PORT_SHORT
Port6 (H1): USB2_PORT_SHORT
Port7 (Camera): USB2_PORT_SHORT
BUG=none
BRANCH=master
TEST=emerge-nautilus coreboot and do eye-diagram test
Signed-off-by: sh.kim <sh_.kim@samsung.com>
Change-Id: I174e5bf96a53bb210481fb88298d5341f6c11dec
Reviewed-on: https://review.coreboot.org/22686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable change Ic6b8ce4a9db50211a9c26221ca10105c5a0829a0
(sb/intel/common: Automatically generate ACPI PIRQ) for BD82X6X.
This generates the main ACPI _PRT table automatically based on the
chipset registers.
Tested on Intel NUC DCP847SKE with Linux 4.13.14:
$ cat /proc/interrupts
CPU0 CPU1
0: 23 0 IO-APIC 2-edge timer
8: 1 0 IO-APIC 8-edge rtc0
9: 0 0 IO-APIC 9-fasteoi acpi
19: 86 0 IO-APIC 19-fasteoi ehci_hcd:usb1
23: 0 0 IO-APIC 23-fasteoi i801_smbus
[...MSI and other interrupts skipped...]
Log messages:
ACPI_PIRQ_GEN PCI: 00:02.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1b.0: pin=1 pirq=1
ACPI_PIRQ_GEN PCI: 00:1c.0: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1c.1: pin=2 pirq=6
ACPI_PIRQ_GEN PCI: 00:1c.2: pin=3 pirq=4
ACPI_PIRQ_GEN PCI: 00:1d.0: pin=1 pirq=4
ACPI_PIRQ_GEN PCI: 00:1f.2: pin=1 pirq=2
ACPI_PIRQ_GEN PCI: 00:1f.3: pin=2 pirq=8
ACPI_PIRQ_GEN PCI: 00:04.0: pin=1 pirq=1
Generated _PRT:
Scope (\_SB.PCI0)
{
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
{
If (PICM)
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
0x00000000,
0x00000010
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
0x00000000,
0x00000015
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
0x00000000,
0x00000013
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
0x00000000,
0x00000011
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
0x00000000,
0x00000017
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
0x00000000,
0x00000010
}
})
}
Else
{
Return (Package (0x09)
{
Package (0x04)
{
0x0002FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001BFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKF,
0x00000000
},
Package (0x04)
{
0x001CFFFF,
0x00000002,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001DFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKD,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKB,
0x00000000
},
Package (0x04)
{
0x001FFFFF,
0x00000001,
\_SB.PCI0.LPCB.LNKH,
0x00000000
},
Package (0x04)
{
0x0004FFFF,
0x00000000,
\_SB.PCI0.LPCB.LNKA,
0x00000000
}
})
}
}
}
Change-Id: I832a86925283d61b64b8268246d9e6f11994c120
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/22859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
It seems that RAM code 0 has been strapped with an incorrect resistor on
Kevin. The resulting voltage divide still puts it well within the ADC
value bucket reserved for that slot, but a little closer to the edge
than necessary. While this doesn't seem to cause any immediate problems
on its own, it still doesn't hurt to fix it (if only for the
documentation value).
On other boards (at least on my Scarlet) the strapping seems to be
correct.
Change-Id: Ic5199834fbeaf734e725ff45b04f45eefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22891
Reviewed-by: David Schneider <dnschneid@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch shifts some comments around to make it easier to replace
values in the ADC strapping bucket table with compile-time conditionals.
Change-Id: Ic51917d3961a51d4e725ff824fb59aeefe149855
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change adds SPD files for memory IDs 1-4 on nami.
BUG=b:70182907
Change-Id: Ic43f944c0cde18244fe4c4d21314b831d048a3a2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Nami uses MAX98357A speaker amplifier and DA7219 codec. This patch
adds max98357a and da7219 under I2C #3 in devicetree and adds SPK DMIC
nhlt support for 4CH DMIC.
BUG=b:70646770
TEST=emerge-nami coreboot
Change-Id: Iecf4059f8ea3d5e34f33f0be227897a8cca636fa
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:70773281
Change-Id: If9b575568cabcbee03ad190b69d9c033890f7fa6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22927
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per the latest schematics, this change configures GPP_B0 for WLAN
wake and uses corresponding gpe bit in ACPI node for WLAN. This hasn't
been tested yet.
BUG=b:70775494
Change-Id: I5198b8083a87d00f890b45986e5e3f62b81686c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22928
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change configures the GPIOs for pen reset and eject lines and
exports required properties using ACPI table.
BUG=b:70773138
Change-Id: I52f6c3dced54259cde8ee6753275622622e15954
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Similar to other KBL projects, this change enables AER and LTR for
root port 1 on poppy.
BUG=b:65570878
Change-Id: Iadad3d2fc46cbba575a776071305925c529a6760
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:62726961
Change-Id: I5a88e67d5a22f8a39427c95821ffee4f2fd717fa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change really fixes the SataMode to select non-RAID mode and
enables SATA which was incorrectly disabled in a71276b
(mb/google/poppy/variants/nami: Fix SataMode configuration in
devicetree).
BUG=b:70160119
Change-Id: Ied6adabdc1d2458972bde628616a198cd41f9f3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Nami uses DEVSLP1 and not DEVSLP0. This change updates the GPIO
configuration for DEVSLP to match the latest version of schematics.
BUG=b:70160119
Change-Id: Ifa181322011a4b8947ecd0fa44dcf790b0d8f657
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch enables customized NIC leds as below:
Green Orange (Amber)
100M off blinking
1000M on blinking
BUG=b:69950854
TEST=Boot on fizz dut and observe the LEDs are behaving as expected.
Perform suspend/resume test and the LEDs are still working as expected.
Change-Id: Ic70587a0cd688e74b5e1ce532c5da954c80cf841
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PCH_SPK_EN uses GPP_A23 and not GPP_A22. This change fixes the gpio
configuration error in the initial change 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: I90d9c009369c53cfec47fe77356e181d5ecf7ad5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22844
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Melfas kernel TS driver (melfas_mip4.c) will look up "ce"
GPIO during driver probe in ACPI _DSD.
But FW does not report "ce-gpios" but "enable-gpios" in _DSD.
Kernel will obtain GPIO from _CRS by index "0" without ID.
Melfas driver does not have separate condition
for MIT-410 so driver will set TS IC power off in probe.
FW now may need to add back "reset" pin in order to hack
this condition to let Melfas driver get "useless" GPIO
so TS IC power (VTSP) will be not off during driver probe by itself.
BUG=b:70149336
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: Icf0451ff0c3df97cb2474e30542a2f46ba67d82a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For Fizz, the default should be AHCI mode and not RAID
mode. Additionally, there is only one drive connector, so
attaching several drives for a RAID is hard.
BUG=b:70146894
Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22837
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
This change selects Kconfig option to disable native SD card
controller in ACPI tables, since it is not used on nami.
BUG=b:70160119
Change-Id: I6180c2b342c69e6a7c357f10b6297d67ea0211d7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable SATA port 0 to support SATA HDD.
BUG=b:69950854
BRANCH=None
TEST=emerge-fizz coreboot and boot on fizz dut
Change-Id: Ifbf5950151758286f8bff7250a68d9d0b3975ef9
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MEM_ID SPD
0000 hynix-H5AN8G6NAFR-UHC
0001 hynix-H5ANAG6NAMR-UHC
0010 micron-MT40A51216JY-083E
0011 micron-MT40A1G16KNR-075E
0100 samsung-K4A8G165WB-BCRC
0101 samsung-K4AAG165WB-MCRC
BUG=b:69268926
TEST=build test
Change-Id: I1fd6335b3f8842252c42009a0a91a5b6ed3ea238
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add INNOLUX P097PFG panel timing. According to Scalet schematic,
if GPIO3_D4 get low status, it will use INNOLUX P097PFG panel;
if GPIO3_D4 get high status, it will use KD097d04 panel.
Change-Id: I43fa5d859a9a529a84c58a953b37d03953ce648a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Move AGESA related headers in soc/amd/common to
soc/amd/common/block/include/amdblocks.
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, headers moved).
Change-Id: I5d3064625ddf8caaf370aabaf93165c6817f1ca0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change provides implementation of variant_memory_params for
nami. Since it uses DDR4 memory, DQ-DQS mapping table is not
required. Also, Rcomp resistor values are provided based on SDP v/s
DDP memory.
BUG=b:70188937
Change-Id: Ic1d0cfdb7d8b02fa0be0a4c54b20057a4c2fc3ce
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates scl_lcnt value for I2C5 to bring the bus frequency
closer to 400kHz.
BUG=b:65062416
TEST=Verified that I2C5 frequency is between 389-396kHz.
Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and
spi.c. The remaining files are AGESA related and will be part of a separate
issue/commit.
BUG=b:62240201
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Due to a schematic error, our code was written to configure more I2S0
pins than are actually used. We're also pinmuxing the whole bank of pins
over to the I2S controller even though we don't need them all. Restrict
the GPIO initialization and pinmuxing to the pins we really need so the
other ones can be correctly used as SKU ID pins on Scarlet.
Also, move the "audio" IO voltage domain selection to the other such
selections in the bootblock, since that covers two whole banks of GPIOs
and there's no guarantee that they're all used for audio (and thus not
needed before ramstage).
BUG=b:69373077
TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2.
Change-Id: I9314617e725fe83d254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
|
|
These pins need to be pull-ups. I forgot.
BUG=b:69373077
Change-Id: I9314617e01d35898254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adds Maxim98357a support for Nautilus using the generic driver
in drivers/generic/max98357
BUG=b:68686020
TEST=With entire merged audio should be enabled on max98357
speaker codec.
Change-Id: I958bf7c1395259b3e3fb30332882fd51a48dc0cc
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus board uses max989357a speaker codec and 4CH DMIC.
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on Speaker and captures on 4CH DMIC
Change-Id: Ie90af02e0935029f53f9020bd78027b6eb31a187
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the original Chromium source, PcdMemorySpdPtr is only set for
cyan, but none of the other Braswell variants. When upstreamed,
it was left set for all boards as it didn't appear to be problematic.
In wider testing, I came across one reks board for which it caused
FSP memory init to fail, so restricting the parameter to cyan only
as it was originally.
TEST: build/boot google/reks with Micron EDF8132A3MA-JD-F RAM,
observe board now successfully boots where it did not previously.
Change-Id: Iacfbd4bc89fa04717baf85704181d346bca2ed2f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22782
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- The touchscreen interrupt was moved from the GPIO 3, as originally
suggested to GPIO 11. This changes the gevent from 2 to 18.
- Add EMMC reset on GPIO 93.
- Add EMMC bridge PCIe reset on GPIO 40.
- Set device enables to high.
- Remove extra SCI comment from GPIO 130.
- Set individual device PCIe reset pins to high.
- Enable global PCIe reset on GPIO 26.
- Mark LPC_CLK1 as unused.
- Update net names based on latest schematics.
- Set Direction and level/edge correctly for SCIs/SMIs.
- Remove SCI for pen detect.
- Add comments.
BUG=b:70234300, b:69681660, b:69305596
TEST=build grunt
Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on
PCIe port 1, so move the OemCustomize file into the variant directory.
- Add comments in baseboard version so it's easier to understand.
- Update reset pins, put the definitions in gpio.h
BUG=b:70255003
TEST=Build and boot Kahlee. Build Grunt.
Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
This patch makes coreboot set the max current and voltage for barrel jack
adapters.
BUG=b:64442692
BRANCH=none
TEST=Boot Fizz. Use chgsup console command to verify the max current and
voltage are set as expected.
Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22623
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow overriding specific GPIOs by SKU ID. Override two GPIO settings
for nasher to save the power consumption when the system in S0ix.
Change as below:
AVS_DMIC_CLK_A1: IGNORE -> Tx1RXDCRx0.
AVS_DMIC_CLK_B1: IGNORE -> Tx1RXDCRx0.
BUG=b:69025557
BRANCH=master
TEST=compile/verify the power consumption change from ~150mW to ~100mW
on clamshell SKU and from ~200mW to ~100mW for convertible SKU.
Change-Id: I9e0674f206426fddb3947273754774b310106334
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
With the old timing, the hblank time isn't large enough,
it may cause display artifacts. So fix it.
BUG=b:70160653
TEST=panel work on Scarlet rev2 board
Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
