| Age | Commit message (Collapse) | Author |
|---|
|
Add EMCP LPDDR4X DDR MT29VZZZCD9GQKPR for ram id 8.
BUG=b:176262460
BRANCH=master
TEST=emerge-jacuzzi coreboot
Change-Id: If00478b9b05ab3ec48b6a8dec37e9f2f9f04e188
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49447
Reviewed-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Dalboz variants do not use an MST hub; remove the i2c tunnel for it.
That bus is actually connected to the battery on these devices, which
should not be exposed to the AP.
BUG=b:175658311
TEST=builds
BRANCH=zork
Change-Id: If1714a5c441bf185efd2517c7c94e57b5f351f5a
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49628
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change disables unused PCIE RP8 and CLKSRC3.
Without this change sasuke cannot enter into s0ix properly.
BUG=b:176862270
TEST=Built and verified entering s0ix
Change-Id: I0828813ed7924669cb0ff97be2565579762c810f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49300
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds fine-tuned USB2 PHY parameters for sasuke.
BUG=176060155
TEST=Built and verified USB2 eye diagram test result
Change-Id: Id374ed238d92077ca28c1162fd9f070029ee71bd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49321
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the USB2 port 3/4/9
1. USB2 port3 assign to WWAN, and elemi have no WWAN.
2. USB2 port4/port9 connect to Type-C C1/C0
BUG=b:177483059
TEST=emerge-volteer coreboot
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I9affc69cc325b5eb0219b50bfe46f66eb0bb2016
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49473
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enhance USB 2.0 M/B C0, DB C1 A1 port:
HS DC Voltage Level(TXVREFTUNE0): 0xe
COMPDISTUNE(COMPDISTUNE0): 0x7
BUG=b:165209698
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I371e4295c2ee161096f0a277c0c649bf217269b2
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
1. Modify STAPM time constant 2500 to 1400.
2. Add telemetry setting:
VDD Slope : 30518
VDD Offset: 435
SOC Slope : 22965
SOC Offset: 165
BUG=b:177399751
BRANCH=master
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I251029389c10ee0f17f368b1c00ac666d372fc3c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Hynix DDR4 DRAM H5ANAG6NCJR-XNC, index was generated by gen_part_id
BUG=b:176313722
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Ia1947fa158a1113c4a0b1a0d55f657ddaac43382
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Two configuration files are added:
1. H9HCNNNFAMMLXR-NEE-8GB: new byte mode
2. MT53E1G32D2NP-046-4GB: new single rank mode
Also initialize the rank number field 'rank_num' for all configs.
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: I1786c1e251e8d6e110cbdce79feeb386db220404
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49108
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The fw_config field SPI_SPEED is not used for zork devices.
To define SAR config, use the fw_config bit[23..26].
Then vilboz can loaded different WiFi SAR table for different SKUs.
BUG=b:176858126, b:176751675, b:176538384
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I5ba98799e697010997b515ee88420d0ac14ca7ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Based on voema schematics, two USB2 ports 3 and 5 are assigned to type C
connectors on Voema board.
BUG=b:177483061 b:172535001
TEST=Build and boot Voema.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I12cef85595e511801ab9c563ae4aa26e25875679
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LTE module is not expected to be powered off during warm reset. Hence
configure the LTE_PWR_OFF_ODL (GPP_A10) gpio pad reset configuration to
PWROK and set the TX state to 1.
BUG=b:163100335
BRANCH=dedede
TEST=Verified through the waveforms that power sequence is meeting the LTE module requirements.
Change-Id: I8676da6186559288aabe078b6158fc01075c7b41
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
LTE module used in metaknight has a specific power on/off sequence.
GPIOs related to power sequence are:
* GPP_A10 - LTE_PWR_OFF_R_ODL
* GPP_H17 - LTE_RESET_R_ODL
1. Power on: GPP_A10 -> 20ms -> GPP_H17
2. Power off: GPP_H17 -> 10ms -> GPP_A10
3. Warm reset: GPP_A10 keeps high, GPP_H17 goes low at least 2ms
Configure the GPIOs based on these requirements.
BUG=b:173671094
TEST=Build and boot Metaknight to OS. Ensure that the LTE module power
sequence requirements are met.
Change-Id: Ibff16129dfe2f1de2b1519049244aba4b3123e52
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
TEST=call do_board_reset() manually.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I355f71e731f1045cd80a133cd31cf4d55f14d91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The default value is not sufficient to correctly configure the Type-C
ports as it has all ports disabled by default. On Volteer ports 0
and 1 are enabled so setting this value to 0x3 and correctly
keeping the IomPortPadCfg values at 0 for ports that have a
retimer and ports that are not configured. These values were set
to 0x90000000 to avoid s0ix issues which arose from the UsbTcPortEn
value being incorrect.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that s0ix cycles complete
without any issues
Change-Id: Ib4f2bd0f68debd4e97ccaab9e1d8a873dc4e4d9f
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48814
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the functions that get called by the coreboot console
initialization code aren't in the SOC-specific code anymore, the SOC's
uart.c can be included unconditionally in the build now. This also
replaces the STONEYRIDGE_UART Kconfig option with the common
AMD_SOC_CONSOLE_UART one.
Change-Id: I09c15566a402895d6388715e8e5a802dc3c94fdd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update ELAN i2c-hid touchscreen configuration
BUG=b:172517685
BRANCH=dedede
TEST=Verify touchscreen is working fine on botenflex
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ia7c81fd0a772968ec32406f1e366a90481fc5ad8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: Ic9cdcc497bf1a9f5bfed5e6d95040bfa602b0b89
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48732
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update PL1 min and max values for Delbin systems
BUG=b:168958222
BRANCH=None
TEST=Build and verify on delbin system
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: I2152f0dbeb0ae463b78464571b6c434830f0082a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
|
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:174338903
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I875f6b32c4053ef6d23ad7606cd35a129a78c306
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49290
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initiate overridetree.cb based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I31e5ac1703476083ac71dac30b0a3299b38384c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow latest schematic to fill gpio table.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a983605b5139ff8510a0cf225e6564b9215cb1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Two USB2 ports 4 and 9 are assigned to type C connectors on Voxel board.
This update configures these USB2 ports for Type C which will allow USB2
port reset message upstream from PCH to CPU to recover a USB3 device
that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Voxel board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia370a449a41701e690c1c507d70bedfce2076a65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The FW config takes 2 bits for USE_FAN[27,28].
So FW_CONFIG_SHIFT_WWAN value should be 29.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ica6d04f9c48aa0800189283608bf57416ac75cf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49236
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:171757619
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Change-Id: I37390535e263b4b9547ad7307278e3360ba836bd
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
This will allow CSE RW FW updates and also fixes the problem where no sound is emitted from the speakers.
BUG=b:176536593
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: Wayne3_Wang <wayne3_wang@pegatron.corp-partner.google.com>
Change-Id: I69962a5b7c7c464280b35c834f7ee1c9b77db6fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49197
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While FORCE_PWR is set high, it prevents retimer from entering low power
state. S0ix failure occurs while USB4 Gatkex is connected on Port-0.
This change sets FORCE_PWR(GPP_H10) low. This FORCE_PWR GPIO will be
toggled by kernel through DSM method while updating retimer firmware.
BUG=b:174166586
Cq-Depend: chromium:2594438
TEST=Verifed s0ix cycles with USB4 Gatkex connected on Port-0.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ie4b442e1078379c522a94bfdc00cd99e6f9b8170
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Remove unused touch controller - Goodix
BUG=None
BRANCH=dedede
TEST=build firmware
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I2a01666bc1e353e21ddf961a0eb721a0cb4013db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49221
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only a google/cyan variant evalutes BDID in ASL.
Change-Id: I3d839333333b4762ae5350734c85471a3c12838a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49003
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename these to soc_fill_gnvs() and move the callsite away
from mb/.
Change-Id: I760c36f65c6122103f2be98fc11ee13832c2772e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48716
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename acpi_create_gnvs() functions under mb/ to reflect
their changed functionality.
Remove now empty mb/acpi_tables.c files.
Change-Id: Ia366867ef73d1ade9805dc29b8e14b3073f44f60
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48707
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These boards without ChromeEC do not set ACTIVE_EC_RW
flag as part of the gnvs_assign_chromeos() function.
Create abstraction to avoid <vendorcode/chromeos/x> include.
Change-Id: Ic6029e1807fcfe7dd2c766ce8221e347b6b096f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48777
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already done in common gnvs_get_or_create() implementation
once gnvs_chromeos_ptr() is defined for platforms.
Change-Id: I90fa2bc28ae76da734b3f88be057435aed9fe374
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48703
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fixes linter error complaining about trailing semicolon.
Change-Id: I3f74f25cb2e3edcdd509abd86d80098241c05741
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fixes a linter error.
Change-Id: I1302e32b0d52e37d9cb4503128edc7d1df1c3bd8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Instead of hard-coding function names in strings, use the __func__
constant for better maintainability.
Change-Id: I151560cd5a135e00f494eda3f9d3b592ee9d984a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a space after each comma to fix linter issues.
Change-Id: I5533c4fc7aa0e986da4350ec56b84903b3111a07
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Two USB2 ports 4 and 9 are assigned to type C connectors on Delbin
board. This update configures these USB2 ports for Type C which will
allow USB2 port reset message upstream from PCH to CPU to recover a USB3
device that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Booted to kernel on Delbin board and verified usb2 port reset
message enable bits through pch xhci_mmio_base + R_XHCI_MEM_U2PRM_U2PRDE
where the offset register R_XHCI_MEM_U2PRM_U2PRDE has value 0x92f4.
Validated various USB3 devices enumeration.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Idb3ce949e1ecf3adc7615e0af79a38a0cc9be18f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49202
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:174118027
BRANCH=octopus
TEST=adjust SSFC value of CBI to select RT5682 or DA7219 then check
whether device tree is updated correspondingly by disabling unselected
one.
Signed-off-by: Marco Chen <marcochen@google.com>
Change-Id: Id37c4c5716ade0851cfcb24e12b390841e633ac9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
|
- Turns audio-related things power on.
- Selects I2S pin-muxing.
- Exposes GPIO "speaker enable" for switching on and off.
BUG=b:176856418
Signed-off-by: Tzung-Bi Shih <tzungbi@chromium.org>
Change-Id: If595657bbddad85bc9a154b3648bae1190cb00b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This change adds internal USB camera into devicetree for sasuke
BUG=None
TEST=Built and checked camera device existence with lsusb
Change-Id: I51b9bb174205d984f1d060afd603f1d087095645
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49162
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds ELAN touchpad into devicetree for sasuke.
BUG=None
TEST=Built and verified touchpad function
Change-Id: If9c25f23ee1c0e88382fff036f77a6753775b81e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change adds DA7219 audio codec and MAX98360A amplifier for sasuke.
BUG=None
TEST= Built and heared speaker sound on OS
Change-Id: Ib48eb74fbfe171d46d0d23859057ba169b56bde2
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Configure GPIO NC pads for sasuke.
BUG=b:172104731
TEST="FW_NAME=sasuke emerge-dedede coreboot"
Change-Id: I3bf8f97708536010da82402ea3d49e387e732d61
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update device tree override to match schematics.
BUG=b:175896481
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I1fb006d750bb2d670885ec8ccc627436c5078072
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for gpio driver for copano
BUG=b:175896481
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I1e0f730c9865ed77c7071245b071315a9c6ea4c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48951
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory table to "mem_list_variant.txt", and command to generate files:
go run ./util/spd_tools/lp4x/gen_part_id.go src/soc/intel/tigerlake/spd src/mainboard/google/volteer/variants/copano/memory/ src/mainboard/google/volteer/variants/copano/memory/mem_list_variant.txt
DRAM Part Name ID to assign
MT53D512M64D4NW-046 WT:F 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
BUG=b:175896481
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Change-Id: I2ace17e8fff12d3f5de15a35f609265d8b6ed6b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48948
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the _PRT generates a GNB IO-APIC routing table we no longer
need to route the PCI interrupts through the FCH IO-APIC. This change
unmaps the IRQs since they are no longer used.
BUG=b:170595019
TEST=Boot with `pci=nomsi amd_iommu=off` and verify /proc/interrupts
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3467934bfcac14311505bec49a12652490554e6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
As part of acoustic noise mitigation calibration, we need to enable
FastPkgCRampDisable upd along with slew rate = 1. This values has been
derived based on noise calibration done.
Please refer document 575216 for procedure.
BUG=None
BRANCH=dedede
TEST=correct value has been programmed and slew rate measurement
is correct on scope.
Change-Id: Ie42c8ab647ff42fa043b6f717a9834f9b9c551f6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
Original Stamp_boost parameter will cause boost time over 2500sec(3960sec)
To pass balance performance and skin temperature test, decrease stamp_boost:
2500 -> 1640
BUG=b:175364713
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test
Change-Id: I44f086af6b5dd552efd2bd1ef4db0d69b652826d
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Add charger current throttling support for dedede baseboard
BUG=None
BRANCH=None
TEST=Built and tested on boten system
Change-Id: I79edba579249111294a982590660196f05be7eaf
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49083
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tuning i2c frequency for elemi
I2C0: 396.6 KHz
I2C1: 395.9 KHz
I2C5: 397.1 KHz
BUG=b:176794161
BRANCH=volteer
TEST=emerge-voleteer coreboot, and measure i2c clock.
Change-Id: I23b04a9b5ff8873d9de12e762e8e2786ef474ac0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update Goodix touch screen reset delay time to 180ms.
BUG=b:176213670
TEST=Build and boot Metaknight to OS.
Change-Id: I5801a36fb7c03b23046df16b1eaf4c548241bba5
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
1. Add ELAN touchscreen/touchpad to overridetree.cb
2. Follow Dalboz setting to add variant.c
BUG=b:174528384
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ic3193ca7957251841e75a7e5c7a16fc5047919fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48001
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make CHROMEOS_DSM_CALIB depend on CHROMEOS, rather than force-select it.
Change-Id: I4c3fd04ec00e0787381c58810938dd48f414635c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The CSE lite SKU has 2 CSE firmware boot partitions vs 3 for the "normal"
SKU; this has nothing to do with building for ChromeOS or not, and by
having this dependency, boards with select the CSE lite SKU are unable to
build with CONFIG_CHROMEOS unset due to Kconfig dependency issues.
Test: build google/wyvern with CONFIG_CHROMEOS not set.
Change-Id: I6959f35e1285b2fab7ea1f83a5ccfcb065c12397
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
I2C0 has amplifier connection, thus set it to PchSerialIoPci.
BUG=b:170273526
BRANCH=puff
TEST=Build and check PCH serial IO config is set I2C0 to Mode 1
Change-Id: I9540f7b5538d37de53bcf43531488d714874a565
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
modify raydium touch screen power on timing to meet requirement
BUG=b:174280232
TEST=build firmware and measured the timing
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I3ecc9d8e21f8c76e9e96cf050dcde83c3c4f4ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48971
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low times for port0,2 and 4 I2C buses.
BUG=b:176519792
TEST=Measured the I2C bus frequency lower than 400 KHz.
Change-Id: Ieed038c93f0972c06cb3fa311742dd22ac2e875d
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Follow Goodix datasheet (GT7375 Programming Guide_Rev.0.1.pdf and
GT7375P Programming Guide_Rev.0.6.pdf) to tune touchscreen power sequence.
Increase reset_delay_ms from 120ms to 180ms.
BUG=b:176511605
BRANCH=dedede
TEST=Build and boot Madoo to OS
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iae35e4da31a3c3afd24c7daf81a5a3e762acd3b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I37403dd3ac3c9320398207d2111e1ddb73d6a130
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Config I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
These tuning value is applied from touchpad as a base line,
and EE measured touchscreen/audio runs at 399/396.7kHz after tuning.
BUG=b:173709409
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: I970d69e6361d7cf6fcfc4e5b0b3c5fbfa885367c
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:173709409
BRANCH=dedede
TEST=EE measured result is 390.8kHZ
Change-Id: I7a6475fd29d4c9f8efa78a42a112b5565511b939
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
According Goodix GT7375P Programming Guide_Rev.0.6, increase the stop
delay time from 100 ms to 160 ms.
The power sequence is not met with the latest guide_rev.0.6.
BUG=b:176270381
BRANCH=zork
TEST=Confirm the measured waveform complies with Goodix touchscreen spec.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I687ffa2eb13a9ddecb3045c5e1540b94417329ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48907
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All Broadwell boards use 8 for MAX_CPUS, so this option can be factored
out into SoC Kconfig.
Change-Id: I311b95ea75a7c6b76b32c7197a0cec86db644234
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Voema port 0 (MB PORT) does not have a retimer so the port needs
to be configured for the SOC to handle Aux orientation flipping.
BUG=b:176462544
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I3d31a5b848f56126f8ffe2babb29085471e8224f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This table was wrong. It's also produced by the SoC code now.
BUG=b:170595019
TEST=Verify PCI IRQ: log messages
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I008b6896064672f9d45a8e12f6cfc62c0cc41536
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
They aren't specific to AC power operation anymore. Also adapt autoport.
Change-Id: Ib04d0a08674b7d2773d440d39bd6dfbd4359e0fb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49089
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All mainboards use the same values for AC and battery, even desktop
boards without a battery. Use the AC values everywhere and drop the
battery values. Subsequent commits will rename the AC power options
accordingly, and will also clean up the corresponding acpigen code.
This is intentional so as to ease reviewing the devicetree changes.
Also update util/autoport accordingly.
Change-Id: I581dc9b733d1f3006a4dc81d8a2fec255d2a0a0f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The EC generates EC_MKBP_EVENT_DP_ALT_MODE_ENTERED when USB-C
connections enter DP alt mode, which should wake the system from S3.
Configure S3 wake events to include MKBP so this actually wakes
the system.
BUG=b:174121852
BRANCH=zork
TEST=Generating DP event on MKBP via EC console wakes morphius
Change-Id: I8100c6253e8e5cae91586c4f2f45d66c15fecc6d
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
INT[E-H] are required because the GNB IO-APIC maps the 32 interrupts
onto the 8 INT[A-H] that feed into the FCH PIC/IO-APIC.
BUG=b:170595019
TEST=Verify ezkinil still boots
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9c6689e212b136f6f3c64152803ed161b2284275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable IPU for voema for MIPI camera.
BUG=b:169551066
TEST=IPU is enabled and shows in lspci.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I34736bffd4dc61a840003afe5afd6a9c8dc32e62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49002
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI backlight support for boards selecting BOARD_GOOGLE_BASEBOARD_HATCH.
PUFF-based variants do not have an internal panel, so do not need this.
Test: build/boot Windows 10 20H2 on google/akemi, verify
display backlight controls functional.
Change-Id: I5ce4c6e1c78299e89760a1356da452d56ba0aee6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49058
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables backlight control under Windows 10.
Test: build/boot Windows 10 20H2 on google/reef, verify
display backlight controls functional.
Change-Id: I4ce613badbdcfb9c843f52408df26c6cbb4b82a2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add functions to read the system and mainboard serial numbers
from VPD tables stored in flash.
Remove board-specific implementations for google/drallion and
google/sarien and select the new Kconfig instead.
Test: build/boot google/akemi with RO_VPD region persisted from
stock Google firmware, verify system/mainboard serial numbers
present via dmidecode.
Change-Id: I14ae07cd8b764e1e22d58577c7cc697ca1496bd5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49050
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove index0 DRAM assignment since it doesn't use in any build.
Add Hynix DDR4 DRAM H5ANAG6NCJR-XNC, index was generated by gen_part_id
BUG=b:175911098
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I853a316c266afafeecff67b263005a77be316e2b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48723
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PUFF-based Chromeboxes need more than the 2s default in order to init
an external display and show the boot splash/menu prompt.
Test: build/boot WYVERN variant, ensure boot splash/menu prompt visible
regardless of display init type used.
Change-Id: Ie6d2151d28058501498a4c501bb221919b4e1b39
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
These Chromeboxes need more than the 2s default in order to init
an external display and show the boot splash/menu prompt.
Test: build/boot one of each variant, ensure boot splash/menu
prompt visible regardless of display init type used.
Change-Id: Ib90136b7e564451aff638af4d42abd97e42b3c19
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Enables backlight control under Windows 10.
Test: build/boot Windows 10 20H2 on google/ampton, verify
display backlight controls functional.
Change-Id: I779f7f3f5a111018fc7b5c50c5750a9eb815d670
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
There are multiple different devicetree setting formats for graphics
panel settings present in coreboot. Replace the ones for the platforms
that already have (mostly) unified gma/graphics setup code by a unified
struct in the gma driver. Hook it up in HSW, BDW, SKL, and APL and adapt
the devicetrees accordingly.
Always ensure that values don't overflow by applying appropriate masks.
The remaining platforms implementing panel settings (GM45, i945, ILK and
SNB) can be migrated later after unifying their gma/graphics setup code.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I445defe01d5fbf9a69cf05cf1b5bd6c7c2c1725e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For easier review of the switch to a new register struct in the
follow-up change, the panel delay times get converted from destination
register raw format to milliseconds representation in this change.
Formula for conversion of power cycle delay:
gpu_panel_power_cycle_delay_ms =
(gpu_panel_power_cycle_delay - 1) * 100
Formula for all others:
gpu_panel_power_X_delay_ms = gpu_panel_power_X_delay / 10
The register names gain a suffix `_ms` and calculation of the
destination register raw values gets done in gma code now.
Change-Id: Idf8e076dac2b3048a63a0109263a6e7899f07230
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Some bridge chip or panel requires dsi signal output before dsi
receiver works.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I3bded27087490f32ee233e615cfad1fd05fb582d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change-Id: I1e63a419db92642df6b7956050c39540c2ae11d6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48781
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 5bb5c43b936f0bb01e08a71df1865343d7be9b88.
Reason for revert: Build bot fails.
Change-Id: I8f022514351b37be135d10ef8486e4aa5fd6361b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48980
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On commit 64c03e3c ("mb/google/poppy: Fix race condition in acpi"),
we introduced a new Power Resource common to all the camera modules,
in order to resolve a race condition when both modules were in use
(e.g. during startup).
The nautilus variant also used the Power Supply I2C2.PMIC.OVTH, which
requires the new common PR, but the new dependency was not added.
Depend on the new Camera Common Power Resource.
Fixes: 64c03e3c ("mb/google/poppy: Fix race condition in acpi")
BRANCH=poppy
BUG=b:174941580
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Change-Id: Ifa6c70b7c02aec0112189eca573e76e53175d70d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: shkim <sh_.kim@samsung.com>
|
|
Initiate peripheral buses based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a828bfb3ba4ee9a9b41cd4e83701672e5ef85bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update galtic device tree override to match schematics.
BUG=b:170913840
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I270cd2a9783030ad3a080b9cfda8a133e801c5ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch add SSD D3 cold support for lindar.
BUG=b:172405687
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ie343bbff3bde4ff2a7e89bd384d5661af372b560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on latest schematic, disable PCIe 7 and 8 for WLAN and SD card.
BUG=b:169356808
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2a4658a382c094c2a5b16b7acaf464f54e9897b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:169356808
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I28ef074225c533e1a97b6ec4a1a5dd1dcc198168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48848
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A new board introduced to Kukui family.
BUG=b:176206134
TEST=make # select Katsu
BRANCH=kukui
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I09fe2b8f6922dfd2af6424830568466fb98f7aee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Files under sb/ or soc/ should not have includes that tie those
directly to external components like ChromeEC os ChromeOS
vendorcode.
Change-Id: Ib56eeedaa9d7422e221efa9c8480ed5e12024bca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48765
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for gpio driver for drobit
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I54ba182c6da3db282961b3c72a4d2d11d1001e95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
drobit memory table as follow:
value Vendor Part number
0x00 MICRON MT53E512M32D2NP-046 WT:E
0x00 HYNIX H9HCNNNBKMMLXR-NEE
0x01 MICRON MT53E1G32D2NP-046 WT:A
0x02 HYNIX H9HCNNNCPMMLXR-NEE
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Icd9439f8449856d4ec6798a4e4310dd139bce05f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48496
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update drobit device tree override to match schematics.
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I48a3024df4270b111b90c4fb56847aad6e65bfa1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add enable acp_i2s_use_external_48mhz_osc flag and then
WWAN sku will use external clock source at next build.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz and check MISC_CLK_CNTL1.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ida747938373f648524b1e7f34bc69e372a69c4f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48556
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
