| Age | Commit message (Collapse) | Author |
|---|
|
This patch disables the SA IPU for hatch since it is
not using the IPU.
Change-Id: Ib2afc4cc4fd7ef98365b0b98130b0e8bc757ac2a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Reading nvdata from non-volatile flash storage. With this patch, it will
pass the firmware test that corrupts FW_MAIN_A and boots up with
FW_MAIN_B.
BUG=b:80501386
BRANCH=none
Test=test_that --board=kukui 172.23.213.147 firmware_CorruptFwSigA
Change-Id: I9ef6bff019ee986ff018202bfd4d4a875526ec6c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/30701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:119899987
TEST=build and flash to rammus, log into rammus and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Signed-off-by: marxwang <marx.wang@intel.com>
Change-Id: Ieadb3609c7634a20e96c7c4dfb96f5e3f23e468b
Reviewed-on: https://review.coreboot.org/c/30607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify ELAN touchpad bus i2c clk from 466Khz to 400Khz.
BUG=b:119628524
BRANCH=master
TEST=measure ELAN Touchpad CLK
Change-Id: Ia8433c6ef320cea9a0145db4ba440d67ccd0f41e
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30588
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The vbt was extracted from the option rom found on stock images.
The vbt.bin is the same across all variants.
The VBT has a modified BDB block 43, the 'Backlight info block' such
that the inverter type for the panel in use is set to
2 (BDB_BACKLIGHT_TYPE_PWM) instead of 0 (BDB_BACKLIGHT_TYPE_NONE).
This only seems to matter on Windows, as without it changing the
backlight duty cycle does not work.
Change-Id: I82c72c561e1058e0b77d80baf330b64f7c6b08e3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30487
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Without eist enabled, fizz's CPU clocks are locked at the
base frequency, and don't scale up or down. This prevents
fizz from idling properly and turbo boost from functioning,
so enable it (as is done for all other KBL boards)
Test: build/boot google/fizz, ensure CPU clocks scale as expected
Change-Id: I77dd0e1df1bf88f5bae18e9f832ca8d60fb777b4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I2e28b9f4ecaf258bff8a062b5a54cb3d8e2bb9b0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Icf34b39d80f6e46d32a39b68f38fb2752c0bcebc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/26484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I99b9c0452ed0e6d580edb5a4f3317d776085b382
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30399
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We have init_bootmode_straps() defined for the same purpose.
Change-Id: Ia2692d8f8986247ea4ce889d6252d3c4c8b27bc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30398
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for sarien platform, the slow slew rates
are fast time dived by 8.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I5d38a1e03af08f106e2422a319b34c3fb54bdf28
Reviewed-on: https://review.coreboot.org/c/30448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Sync'ing the sku_ids list in the master sku sheet for Pantheon.
BUG=b:121207221
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ic03c3a6fe238f2692ce15c45016115087380c0ca
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add DRAM support for google kukui.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1ed01404343745c883b22a648966327bdcabc5c2
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/28438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Use smm-$(CONFIG_HAVE_SMI_HANDLER) instead of smm-y
Change-Id: I0f91bc3e6c8ab31d837ab89af62d700b35c1e01b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
HAVE_SMI_HANDLER is selected here: broadwell/Kconfig
Change-Id: I50c664198a954f661416c8cb1ced05f8775d8e07
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
HAVE_SMI_HANDLER is already selected in soc/intel/skylake/Kconfig
Use "smm-$(CONFIG_HAVE_SMI_HANDLER)" in Makefile.inc files.
Change-Id: Ia60e34ee03958b05f2ac0c326632b6dd9f02a2e0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch ensures to make memory protected range between
01C00000h - 01FFFFFFh as per winbond spi datasheet
https://www.winbond.com/resource-files/w25q256jv%20spi%20revb%2009202016.pdf
section 7.1.15
BUG=none
BRANCH=none
TEST=build for hatch.
Change-Id: I52d8dbba14bd060b48a7fe8ee009219413ef89ca
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30552
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures to make memory protected range between
01C00000h - 01FFFFFFh as per winbond spi datasheet
https://www.winbond.com/resource-files/w25q256jv%20spi%20revb%2009202016.pdf
section 7.1.15
BUG=none
BRANCH=none
TEST=build and boot dragonegg.
Change-Id: Ife451233f60ef680088babbc824bfc5a17078cb9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30551
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add reset delay in power resource to prevent from failing to bind after
unbinding. And boards including yorp series - bobba / phaser and bip series
- ampton are affected.
BUG=b:121286833
BUG=b:117474421
BUG=b:121019320
BRANCH=None
TEST=emerge-octopus coreboot,
verified that WACOM touchscreen can re-bind successfully.
Change-Id: Icf690fc8e9450d559b642d1c88e29ff5d52c5488
Signed-off-by: Marco Chen <marcochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch enables CNVi wifi for hatch
1. Enable CNVi device in device tree
2. Configure GPIO pad config for CNVi
BUG=b:120914069
BRANCH=none
TEST=check if code compiles correctly and verify GPIO configuration with
schematics
Change-Id: I0c5542737d3a629b6a40116b4aa8ab6cbdd6a4dc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30436
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correcting order of display related GPIOs and also adding not connected
pin definitions for display GPIOs
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I9498284d263516f65513d6395883b6b09dd70fd5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch enables the x4 NVME device for hatch,
* Enable the Root port 9.
* Assign the usage type for clock source.
* Configure the GPIO for CLK SRC 1.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: I69be6b21a5ae5962877a5c38180b5ffac532fed4
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30431
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the configurations for,
* USB 2.0 ports.
* USB 3.0 ports.
* Enables USB xHCI controller.
* GPIO config for USB2_OC2 and USB2_OC3.
* Add the ACPI objects to configure USB ports.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Ia7b25c25b8208c678aeae3a32033611b69b54062
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30457
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the SATA for hatch,
* Enable the SATA port 1.
* Configure the GPIO for SATA.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Iaf800d1531688c3d3b82600038ea1d7160ae4b0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30435
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7fdf8934187d2786fdac23ed4460147867c25044
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30460
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
New emmc DLL values for Fleex.
BUG=b:120561055
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: Id0022e9d0f0a7802113bbf193decff3c8aaa04f8
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30226
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
* Enable host bridge.
* Enable CSME.
* Enable Power Management Controller.
* Enable Primary to Side Band Bridge Controller.
* Enable SmBus Controller.
BUG=b:120914069
BRANCH=None
TEST=code compiles with the changes
Change-Id: I2fbf0ece845a7114ce5ab7f6482a935d9275deee
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/30465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Modify the vbios's eDP signal setting from level0(0dB)
to level1 (3.5dB) for bard
Add VBT blobs and include it in cbfs
BUG=b:119448457
TEST=Test & measure eDP signal
Change-Id: I0b854a6adad43844282aed61d26e798727b5cb62
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30375
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Phaser.
BUG=b:120561055
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: Ie8d56e0faf5c96d980c0614a61fbc6eacf582943
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30144
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3b9217a7d9a6d98a9c5e8b69fe64c260b537bb64
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable SPI controller(D31:F5).
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I4d3acd3f31650d5b39927f8e3cfbb6187541653f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/30438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Enable LPC/eSPI controller(D31:F0). EC would be using
eSPI interface, since the strap GPP_C5 is pulled up.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ia4baf80a775ba8898055f82e80dc583e65c4ed0b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Add SMI handlers for below SMI events:
1. eSPI SMI event.
2. ACPI enable/disable SMI event
-> Add support for EC to configure SMI mask on ACPI disable.
-> Add support for EC to configure SCI mask on ACPI enable.
3. Sleep(S3/S5) SMI event
-> Add support for EC to configure wake mask for S3/S5 event
Change-Id: I7127b44712cd89b3d583e9948698870ca0c64b2b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Adding hot plug detect GPIO support for external Type-C display in event for
cable connect/disconnect.
Change-Id: If9d52dc0f9916f761c8fdd88c76968aaf663e650
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30365
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable EC LPC interface and configure below LPC IO decode ranges:
1. 0x200-020F: EC host command range.
2. 0x800-0x8FF: EC host command args and params.
3. 0x900-0x9ff: EC memory map range.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ie5d92df80d6b3a5913d0cbe78c1b8eefb5269d4a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implementation adds below code:
1. Add SOC ACPI code in dsdt.asl
-> platform.asl
-> globalnvs.asl
-> cpu.asl
-> northbridge.asl
-> southbridge.asl
-> sleepstate.asl
2. Add chromeos.asl in dsdt.asl
3. Add EC ACPI code in dsdt.asl
-> superio.asl
-> ec.asl
4. Remove config for WAK/PTS ACPI method as chromeec
doesn't implement those.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Icf1b1d7e34a7e863139c3583903f3b1e2cdc8da6
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implemetation adds EC SCI, SMI, S5/S3 wake trigger events.
Also adds the EC specific ACPI configs to enable support for ALS,
EC PD device and PS2 keyboard device.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I3a86f609c269cb59e546fc7ba4ba032e5ea8341a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30281
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 969ed357f823659a6861a2ca38f3ad9d7b58f949
Reason for revert:
According to partner issue b:112448519 comment#80, it impacts
skin temperature specifications.
Change-Id: I7603c3816f34adebc1f67eff6fad214557544022
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This patch ensures following 2 features
1. Enable IGD controller in devicetree.cb
2. Pass required FSP UPD to perform internal graphics initialization
Change-Id: I607199590d793a70e1e20bb3241fc34467aa829d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This implementation adds below support:
1. Add support to read memory strap.
2. Add support to configure below memory parameters
-> rcomp resistor configuration
-> dqs mapping
-> ect and ca vref config
3. Include SPD configuration
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc -bmplk" emerge-hatch coreboot
Change-Id: I9bda08bd0b9f91ebb96b39291e15473492a6bf19
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30248
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:120914069
BRANCH=None
TEST=USE="-intel_mrc" emerge-hatch coreboot
Change-Id: I91db5745d1db16ab4b2fbb7f8c415bd7c1eb29e9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Incorporating some feedback to initial hatch mainboard checking
(CL:30169) that came in after the CL merged.
Updated the chromeos.fmd with the following,
* SI_ALL = 3MB
* SI_BIOS = 16MB
BUG=b:20914069
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a -v
Change-Id: I4e311c68873f10f71314e44d3a714639a06dbee8
Signed-off-by: Shelley Chen <shchen@google.com>
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30296
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit a914152fa6072c443ccd18de22412b47a228e754.
Reason for revert:
According to the partner on this project, custom values like this
are no longer necessary.
Change-Id: I393eb4997f58abe0f77161999474994f06741519
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Remove duplicate entry of dptf_enable.
BRANCH=None
BUG=None
TEST=None
Change-Id: I3ddd6a702180624d31c5c58c71acdce8f627c925
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for micron_dimm_MT40A512M16TB-062EJ (ram id: 12)
BUG=b:121217853
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I45e6a7a183556fb085f5442cd6bb429d79ef4235
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp micron_dimm_MT40A256M16LY-075F (ram id: 11)
BUG=b:120884302
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Icf731bfefd550e9b94b6404bc870d4d76451deb1
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add code support to enable H1 TPM interfaced to SOC on GSPI0.
The TPM interrupt is mapped to GPP_C21.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: Ib63a0b473f632d91745102ebd01993e8d65b9552
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30210
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation cleans up gpio configuration functions
and limit definition to baseboard only for now, until variant
specfic overides are needed.
BUG=b:120914069
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot
Change-Id: I563f6b97812b32d6e3d99e3df512dc112da78aea
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30291
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 999b916015ea0558e3821bdb51501b43a60b5ed6.
The DMIC doesn't have an ACPI id. The patch which enables ACPI
device with id DMIC may create conflict in the feature. Also the
ACPI id "DMIC" doesn't comply with ACPI naming conventions. The
issue for which the patch was introduced, is already addressed in
kernel DMIC driver and the patches are upstreamed in to the Linux
kernel.
Change-Id: I42cb076700dcb5906599471bebfcd5b265b17644
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/c/30151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change-Id: Iab2737940f07afb4f5a29ff50e6cb2a22027c51b
Signed-off-by: Bob Moragues <moragues@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30094
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Yorp.
BUG=b:120561055
BRANCH=octopus
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: I771c959a15959160224f056c0a16aa65bfbba94e
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Use 2T memory timings on Liara for all board IDs.
BUG=b:116082728
TEST=Build & boot on Liara
Change-Id: I5814e63db35cf7761f4f20792b0f3cf4120a1b60
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/30285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@google.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Set CONFIG_NO_FADT_8042 to avoid probing for the 8042 controller.
This speeds up boot on nocturne by 1.3 seconds:
Before change:
[2.162266] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
After change:
[0.867735] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
BUG=b:120960844
BRANCH=none
TEST=build, flash, and boot nocturne; check dmesg to verify that
boot is faster and that you don't see the following log in dmesg:
[0.671501] i8042: Probing ports directly.
Change-Id: I62a16e6de5e74fa17970d9967f6d1628497ec1d3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/30283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The TXE PCI device serves no function under Linux, and doesn't
work properly under Windows, so disable/hide it from the OS.
Test: Boot Windows 10 on google/squawks, verify TXE not visible
under Device Manager.
Change-Id: Idaa152e15106b826fd5aa787090acd45719f4228
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...]
in additon to changing the touchpad/touchscreen interrupts from
edge to level triggered, also marked them as maskable. This not only
broke the touchpad functionality, but caused issues with the touchpad
as well. Revert the touchpad to being non_maskable for all cyan
variants with a touchscreen.
Test: boot GalliumOS on google/cyan with a range of kernel versions
(4.15.18, 4.16.13, 4.17.x, 4.18.x) and verify touchscreen functional,
touchpad working properly (not jittery)
Change-Id: I0e0357912f9404af7d0f4e7938a1a94c74810b37
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Define SATA mode to AHCI mode instead of 0, make devicetree more
readable.
BUG=N/A
Change-Id: I903545d9487c1409f9008407fe5bee6aa4959b98
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable ELAN Touchpad and Disable ALPS Touchpad
BUG=b:119628524
BRANCH=master
TEST=ELAN Touchpad can work normally.
Change-Id: I7839459a70768fa95ba4871b1915d2ea86419bbb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Change-Id: I4ee3cc42302c44dc80ae1f285579a4d1775aec16
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The previous settings caused the I2C frequency for the audio bus to be
too high, at 417kHz. The settings in this commit correct the frequency
to 396kHz.
BUG=b:119423345
Change-Id: Ibed886e6e1b0df4df6b87f6291e515364b3bf718
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit ad41f5512306d118047d2f7243678ddb32b4b06b.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Elan touchpad and WACOM touchscreen
BUG=b:119924134, b:120103010
BRANCH=master
TEST=Verify touchpad and touchscreen on arcada work with this change.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I3dcdb4eeeb32766e64553d9e69e6b7e2b5ba85aa
Reviewed-on: https://review.coreboot.org/c/30146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Sync'ing the sku_ids list in the master sku sheet.
BUG=b:112876867
Change-Id: I658e8dc67679b5b528ab267861a1151f50e42414
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dptf settings for Charger throttling. Also, update Power
Limit1 minimum value setting from 4.5W to 3W.
BUG=b:112448519
BRANCH=octopus
TEST=Built and tested on Fleex system
Change-Id: I8c2a796ff28254ebef28ed5745b344f925d6e649
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Bobba would prefer to use different SAR values per sku-id for regulatory
compliance. This commit uses the newly added interface for custom wifi
SAR CBFS filenames.
CQ-DEPEND=CL:*729429
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: I354382d651d65d533459f0ca460ca6fd6de547fd
Reviewed-on: https://review.coreboot.org/c/30223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
helper function
This patch replaces cpuid(1) references from icelake mainboard
with x86 cpu common code library functions cpu_get_cpuid().
- cpu_get_cpuid() -> to get processor id (from cpuid.eax)
Change-Id: Ia12d95d911dd6ee60a3a35937264fef668ad9e35
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This patch implements board reset on the Cheza board. The real board
reset used by the operating system uses the PMIC, but unfortunately the
PMIC needs to be configured right for that to work. The PMIC
configuration currently happens in the Qualcomm blob (QcLib) that is run
from romstage, but vboot needs to be able to reboot during verstage
already. Porting all the PMIC initialization code to run in the
bootblock seems excessive (and at odds with the goal of doing as little
as possible before verification), so we'll just do a little hack and ask
the EC to perform a cold reset instead. For vboot purposes, this should
work just as well.
BUG=b:118501305
TEST=Hacked vboot code to call vboot_reboot(), confirmed that board
reset and came back up as expected.
Change-Id: I3858d95f481884a87c243d4fa3d6369c1e8a5a2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New emmc DLL values for Bobba.
BUG=b:120561055
TEST=Boot to OS, chromeos-install, mmc_test
Change-Id: I5a0d9587a91b3c71c042cd8ea360c816ea29fb91
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30176
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
file Module Part Number
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
file Module Part Number
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Change-Id: I64e79904c7ad95091ea29d9f80444c4e3b493471
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update the TRACKPAD_INT1_1V8_ODL GPIO configuration so that it acts as a
wakeup source
BUG=b:119598593
BRANCH=octopus
TEST=Ensure that the system wakes up on trackpad events. Ensure that the
suspend_stress_test runs successfully for 25 iterations.
Change-Id: I28292682cf9c8037abb87d265e49a60139550db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/30171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I15cfbbab15b940641c3952f2cfb4b11c37574816
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add reset delay in power resource to prevent bind to fail after unbind.
BUG=b:119795901
BRANCH=master
TEST=emerge-octopus coreboot,
verified that WACOM touchscreen can re-bind successfully.
Change-Id: Idcf02b1c931ed64951995403ec9ebe6b8f2db31d
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30099
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
There's no LAN connection on Arcada board, so disable PCH GBE.
BUG=N/A
Change-Id: I07c66df50dbe9fefd95a67b5af9e3f61ce6a18aa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
correct memory part name
form hynix_dimm_H5ANAG6NCMR-VKC
to hynix_dimm_H5AN4G6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I0c33343eb1269919fba324333897805da1d1ff9b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
PEN_EJECT GPIOs are active high and also require an internal pull-up.
Update the GPIO configuration appropriately.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus
tools open on pen eject. Ensure that the system can enter S0ix and S3
states successfully when the pen is inserted. Ensure that the system
wakes on Pen Eject. Ensure that the system does not enter S0ix and S3
states when the pen is placed in its holder. Ensure that the
suspend_stress_test runs successfully for 25 iterations with the pen
placed in its holder.
Change-Id: Ibf9cb214a8ce7561efbb77a7e99d1e386cf064c3
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Synaptics Trackpad wake event is incorrectly routed to GPE0_DW2_02. The
concerned GPIO is not connected and hence wont trigger a wakeup. Fix the
GPE wake configuration for synaptics trackpad.
BUG=b:120666158
BRANCH=octopus
TEST=Ensure that the wake on trackpad works with Synaptics touch pad.
Ensure that the system can enter S0ix successfully(run
suspend_stress_test -c 25).
Change-Id: I87b8c266266280f61700839d428e6f8938b0f72f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30105
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Part Number
Correct Ram_ID=0b0011 SPD Module Part Number to "MT40A1G16KNR-075:E" from
"4ATS1G64HZ-2G6E1".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I9d582b3753de9a48865eb6eca7e4fbdb31b799ff
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Number
Correct Ram_ID=0b0000 SPD Module Part Number to "H5AN8G6NAFR-UH" from
"HMA851S6AFR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I1f6e885638589a35334a9a8f905af4877c5d1f91
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Part Number
Correct Ram_ID=0b0010 SPD Module Part Number to "MT40A512M16JY-083E:B"
from "4ATF51264HZ-2G3B2".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I6847a55968260cdbc1588ddeb8d23c515ad87920
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
