| Age | Commit message (Collapse) | Author |
|---|
|
Make GPIO_4 and GPIO_5 PAD_NC in ezkinil/gpio.c. None of the Ezkinil SKUs
use internal stylus and hence pen pads are configured as NC.
BUG=b:164892883, b:165342107
TEST=Verified taht pen detect GPIO does not cause spurious wakes.
BRANCH=None
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I7557575cf8b8e0f849e05bda1d69acf61e91a157
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44629
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Utilize the SOC_AMD_COMMON_BLOCK_GRAPHICS_ATIF option to provide
full range backlight settings to the kernel.
BUG=b:163583825
Change-Id: I3c337fad38e668488800f4d6bc583a82a93659d3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove references to clk_pm_support which is currently ignored
by Picasso AGESA FSP.
BUG=b:161218965,b:162423378
TEST=Build test Trembyle and Dali, boot to ChromeOS 5 times each
Change-Id: Ic5d6abc56821863b68e45c11763f00d2b6410983
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44556
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:161579679
BRANCH=master
TEST=1. emerge-zork coreboot chromeos-bootimage
2. power on proto board successfully
Change-Id: I713ac3a47c2d47035affb32e6c604b9af23aa90e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:164757545
BRANCH=master
TEST=1. emerge-zork coreboot chromeos-bootimage
2. power on proto board successfully
3. measure i2c freq by scope is close to 400kHz
Change-Id: Icb27ff8a4960caaebc542ee4e507f1611da5a77e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Clean up of bt reset_gpio removal function.
TEST=Boot and observe log showing bt reset_gpio was removed
BUG=b:157580724 - Add reset_gpio for Bluetooth
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1d40ad16dd3c624d4be89d9eea1835cc4e72c03d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44273
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change sets the EFS config for SPI read mode to normal read mode
when using em100. With this, the boot is stable again without any
random hangs in PSP.
BUG=b:164429022
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I4cd3673dcc44a61905719a57f734df2fb9f4e6e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
current setting got 0.278us which is less than the min 0.3us.
increase i2c2 data hold time for TP.
BUG=b:163613330
BRANCH=master
TEST=1. emerge-zork coreboot chromeos-bootimage
2. data hold time measured by scope: 0.3805us
Change-Id: I2d564983383c17ed43cc5cc5aaff0fcd67ce6928
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Those flags already get unconditionally set in soc/amd/picasso/acpi.c.
Change-Id: I978c7d67480499d92c193d5bb87bc876211187db
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Currently sku_id is used to enable/disable eMMC as boot media on
Dalboz. This patch will check eMMC bit in firmware configuration
table to enable/disable eMMC.
On Dalboz Proto and EVT devices with eMMC, there was an issue found
after SMT. This patch checks for board_version instead of SKU_ID to
configure eMMC in HS200.
Configure HDMI based on daughterboard_id in FW_CONFIG.
BRANCH=none
BUG=b:152817444
TEST=Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: Ifa2a49a754d85fb6269f788c970bd9da58af1dad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently SKU_ID is used to enable/disable eMMC as boot media on
Ezkinil. This patch will check eMMC bit in firmware configuration
table to enable/disable eMMC.
BRANCH=none
BUG=b:162344105
TEST=Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: I62318cf71ec70790f2d9e787febd1e0b787741fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add helper function variant_get_daughterboard_id() to read
daughterboard id bits (0-3) in firmware configuration table in CBI.
BRANCH=none
BUG=b:162344105,b:152817444
TEST=Check if daughterboard id bits (0-3) can be read from FW_CONFIG.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: Ia3c882439bfbe6da28be2df0ec0c976d5c142677
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44424
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After confirming that all zork variants and phases have valid
FW_CONFIG value in CBI, this patch is dropping FW_CONFIG validity checks
like VARIANT_HAS_FW_CONFIG and VARIANT_BOARD_VER_FW_CONFIG_VALID in Kconfig
and will also remove associated helper functions.
BRANCH=none
BUG=b:162344105,b:152817444
TEST=Check if FW_CONFIG bits can be read in coreboot and FW_CONIFG helper
function do not return 0 if board has a valid FW_CONFIG in CBI.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Change-Id: I633dc7c500ef8759f3fffb0db6b76d96257c3c9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
CB:44362 ("mb/google/zork: Reorganize chromeos.fmd to increase WP_RO
to 8MiB") updated the flash layout which moved RW_SECTION_A and
RW_SECTION_B to different addresses than before. PICASSO_FW_A_POSITION
and PICASSO_FW_B_POSITION configs need to be updated accordingly to
retain the same behavior as before i.e. amdfw_a/b are placed at the
start of FW_MAIN_A/B by placing them right after the CBFS header.
This change fixes the value of PICASSO_FW_A_POSITION and
PICASSO_FW_B_POSITION to maintain amdfw at the start of RW-A/B CBFS.
BUG=b:161949925
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I177fb38af6380c36397d2a72d5ec00965087d528
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44425
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Starting with v3.6 of reference schematics, headphone jack interrupt
is moved to a standard GPIO instead of using CODEC_GPI. Thus, we no
longer need I2S wake to be enabled in the ACP for boards using v3.6+
version of schematics.
This change sets `acp_i2s_wake_enable` and `acp_pme_enable` to default
0 in baseboard devicetrees and overrides to 1 in update_hp_int_odl()
if the board is still using older version of reference schematics.
BUG=b:159934887
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I44b40db95b5148fe483c7340c5bd0d58627970a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44403
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In CB:43701 the trembyle touchscreen parameters were not updated
to expose the stop gpio properly.
BUG=b:162973325
Change-Id: I6f5da1c556ba1c6ccabf699491d3b635aa79f7c0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change reorganizes flash map layout for zork to allow WP_RO to
grow to 8MiB. This is to allow more space for the firmware UI screens
in RO. Following changes are made in the layout:
1. MRC_CACHE_HOLE is dropped since only one slot of 64K is used for
MRC cache. Next section can start on 64K boundary immediately after
MRC cache.
2. RW_SECTION_A and RW_SECTION_B are dropped down in size to 3MiB
each. Each region is currently at ~2MiB of usage.
3. RW_ELOG is restrictred to 4KiB as that is the maximum elog size
supported by coreboot.
4. SMMSTORE is restricted to 4K.
5. RW_LEGACY region is dropped down to ~1.9MiB.
BUG=b:161949925
TEST=Verified that write-protection for RO still works fine, device
boots in recovery and non-recovery mode. Also, verified that the dump
of fmap looks correct:
dump_fmap -h firmware/image-trembyle.serial.bin
name start end size
WP_RO 00800000 01000000 00800000
RO_SECTION 00804000 01000000 007fc000
COREBOOT 00875000 01000000 0078b000
GBB 00805000 00875000 00070000
RO_FRID 00804800 00804840 00000040
FMAP 00804000 00804800 00000800
RO_VPD 00800000 00804000 00004000
RW_LEGACY 0061d000 00800000 001e3000
SMMSTORE 0061c000 0061d000 00001000
RW_NVRAM 00617000 0061c000 00005000
RW_VPD 00615000 00617000 00002000
RW_SHARED 00611000 00615000 00004000
VBLOCK_DEV 00613000 00615000 00002000
SHARED_DATA 00611000 00613000 00002000
RW_ELOG 00610000 00611000 00001000
RW_SECTION_B 00310000 00610000 00300000
RW_FWID_B 0060ff00 00610000 00000100
FW_MAIN_B 00312000 0060ff00 002fdf00
VBLOCK_B 00310000 00312000 00002000
RW_SECTION_A 00010000 00310000 00300000
RW_FWID_A 0030ff00 00310000 00000100
FW_MAIN_A 00012000 0030ff00 002fdf00
VBLOCK_A 00010000 00012000 00002000
RW_MRC_CACHE 00000000 00010000 00010000
SI_BIOS 00000000 01000000 01000000
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I882f3d813c08ba5fb0ad071da4f79e723296f4b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
dirinboz does not support native HDMI, config DDI as below:
DDI0: eDP
DDI1: DP
DDI2: DP
BUG=b:161579679
BRANCH=master
TEST=1. emerge-zork coreboot chromeos-bootimage
2. power on proto board successfully
Change-Id: I9dffdf5654680e3c2c0b259ee82a471f8ff14f56
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:161579679
BRANCH=master
TEST=1. emerge-zork coreboot chromeos-bootimage
2. power on proto board successfully
Change-Id: Ia736b0f25824eebe4ef25a11646f82963611e3b3
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The USB OC pin mapping is similar enough to move it to the base board
and just have two overrides for trembyle, which is based on an older
version of the schematics, and one override for woomax, which doesn't
use one USB port.
BUG=b:163081097
Change-Id: I7e305d7e6f51d7ef7a4c699e3bacc6bcd699d2f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change-Id: I68b7529733e604ac45919a54e094be7eeb044458
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts the code from commit 728c0787f2 that removes the reset
GPIO from the touchscreen ACPI interface.
That patch exposes a bug which leads to an invalid opcode trap in the
touchscreen code. Reverting this gets the system working again, but is
not a long-term solution.
BUG=b:162596241
TEST=System boots to login screen.
Change-Id: I57a070d94f961cec43834c8bedd5dafc8a54171a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43078
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO_89 was marked as EN_DEV_BEEP_L in pre-v3.6 schematics, but it was
never really used on any of the zork variants. Starting with v3.6,
GPIO_89 is left unused in schematics.
This change configures GPIO_89 as PAD_NC in baseboard GPIO
table. Since EN_DEV_BEEP_L still needs to be driven high to allow
speakers to work, GPIO_89 is configured as PAD_GPO driven high on
pre-v3.6 schematics.
BUG=b:62108046
Change-Id: I026cd6cb598667ce6e115c3ec9357a6a56051d39
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44190
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for touchscreen power control using:
* GPIO_90 for trembyle based boards
* GPIO_32 for dalboz based boards
By default, baseboard tables configure these GPIOs as PAD_GPO driven
low and override trees expose these pads as enable_gpio to be used by
ACPI power resource.
In order to support pre-v3.6 boards, override tables configure these
pads as PAD_NC and drop the enable_gpio setting from device tree based
on board version.
BUG=b:161935640, b:162747210
Change-Id: Iba5e36b65b44ea11613b4d5fc8f13ce6433f83ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44193
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
v3.6 of reference schematics have switched the polarity of reset
signal to touchscreen controller from active high to active low. This
change updates the default configuration in baseboard gpio tables to
set the reset GPIO to output low and override tables in variants to set the
reset GPIO to output high. Additionally, devicetree by default exposes
ACTIVE_LOW configuration for reset GPIO. In order to support pre-v3.6
boards, reset GPIO is updated to ACTIVE_HIGH based on board version.
BUG=b:161937506
Change-Id: I092f274d8eb1920a1cd6d3eccbe8f26b0b28928a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create function update_dmic_gpio to update DMIC GPIO for ACP machine and
use find_dev_nested_path function for consistency.
BUG=None
BRANCH=None
TEST=None
Change-Id: I96cf207f24c6117d98ff2bf7e6e5cd282489e805
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44158
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HP_INT_ODL is no longer connected to CODEC_GPI in schematic version 3.6.
Split variant_audio_update into update_dmic_gpio and update_hp_int_odl.
Changed GPIO_29 from PAD_NC to PAD_GPI in Trembyle. Changed GPIO_84 from
PAD_NC to PAD_GPI for Dalboz. Changed HP_INT_ODL to appropriate pin in
both boards devicetree.cb.
BUG=b:161938476
BRANCH=None
TEST=None
Cq-Depend: chromium:2335424
Change-Id: I05ffb063ab99823d07be6eaa911efbde3cc4ff55
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44157
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Added VARIANT_SUPPORTS_PRE_V3_6_SCHEMATICS and
VARIANT_MIN_BOARD_ID_V3_6_SCHEMATICS. Added helper functions to check
if variant uses v3.6 and if variant uses CODEC GPI.
BUG=b:161938476
BRANCH=None
TEST=None
Change-Id: If86e1ea3c02db354c7b410f1bbc1daacb483cc51
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44156
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
update telemetry value for SDLE test result.
BUG=b:160698427
BRANCH=None
TEST=emerge-zork coreboot
Change-Id: Icce57f9be2732ff79f336daa6c447a30247366cf
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
a. USI_REPORT_EN is no longer set to high in coreboot. Instead
GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this
pad as required.
b. Add Delay after stop_gpio Low - 300ms
BUG=b:162263398
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I3d4dcb6e5cae5d9515abfd415315ec4114ca80b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44107
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DRAM support list
0x00 HYNIX HMA851S6CJR6N-VK
0x01 HYNIX H5ANAG6NCMR-VKC
0x02 Samsung K4A8G165WC-BCTD
0x03 Samsung K4AAG165WB-MCTD
0x04 Samsung K4A8G165WC-BCWE
0x05 HYNIX H5AN8G6NDJR-XNC
0x06 HYNIX H5ANAG6NCMR-XNC
0x07 Micron MT40A512M16TB-062E:J
0x08 Micron MT40A1G16KD-062E:E
0x09 Samsung K4AAG165WA-BCTD
0x0A Samsung K4AAG165WA-BCWE
BUG=b:161579679
BRANCH=master
TEST=build
Change-Id: Ib9fa5ae98568d659326d431a4006174a343fa299
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds support for pen insert/eject operations in S0 and
wake on pen eject from S3 for vilboz.
BUG=b:157628650
Change-Id: I7ba0881b67dfb67c032667d591f7d1806a50af22
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In kernel clk for AMD SoCs we expose a generic clk by the name oscclk1.
This oscclk1 is a fixed 48Mhz frequency clk in RV.
In Zork oscout system clock is linked to rt5682 mclk. Setting mclk-name to
oscclk1 tells rt5682 driver its mclk is oscclk1.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
BUG=b:158906189
TEST=rt5682 driver get the correct clk and tested audio playback
Change-Id: Ic565e8e0573e085e5759b2d3688cc0a4533b67fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For dirinboz
DRAMID 0x9: K4AAG165WA-BCTD
BUG=b:161579679
BRANCH=master
TEST=build
Change-Id: I28c0d23f96c5b9c975ffead3a1cac66cbda8c293
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Set platform defaults for SPI settings in Kconfig for EFS.
BUG=b:158755102
TEST=Build and boot test on Tremblye and Morphius. Verify
values in output image in a hex editor. Measure 1st x86
timestamp, perf improves by over a second.
Change-Id: I765dada14700f4800263d2d3844af07fad0e5b71
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43303
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There was a mix of open coding DXIO logical lane numbers and clkreq
pins. And there are separate macros depending on the baseboard
as well as processor type. Remove the indirection and supply the values
directly in the descriptors.
BUG=b:162423378
Change-Id: I779cb0a514e3b668265e6039d6e7e7bd0f3d49ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Configure the correct eMMC present flag for Ezkinil new added sku_id.
0x5A020015 NVME present
0x5A020016 eMMC present
0x5A020017 eMMC present
BUG=b:159761042
TEST:none
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I1b89cc4568283d5dbebf0ab7ac578368d3a3637e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43753
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:162010077
Change-Id: Iba3e3ec62cdfd818077017abd28fa754c2ae7797
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
sustained_power_limit = 12w
fast_ppt_limit = 24w
slow_ppt_limit = 20w
BUG=b:162377903
BRANCH=master
TEST=emerge-zork coreboot chromeos-bootimage
Change-Id: I9baf9990e26edbbadfba85bc16b380c46684033d
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add bluetooth reset gpio 143 to dalboz baseboard devicetree
Add bluetooth reset gpio 14 to trembyle baseboard devicetree
Remove bluetooth reset_gpio when not supported on a specific board
variant.
BUG=b:157580724
TEST=Boot Ezkinil with Realtek 8822CE, observe log
[ 12.240720] Bluetooth: af_bluetooth.c:bt_init() HCI device and connection manager initialized
[ 12.249272] Bluetooth: hci_sock.c:hci_sock_init() HCI socket layer initialized
[ 12.256520] Bluetooth: l2cap_sock.c:l2cap_init_sockets() L2CAP socket layer initialized
[ 12.264575] Bluetooth: sco.c:sco_init() SCO socket layer initialized
[ 12.273700] usb 3-2: GPIO lookup for consumer reset
[ 12.273702] usb 3-2: using ACPI for GPIO lookup
[ 12.273705] acpi device:18: GPIO: looking up reset-gpios
[ 12.273707] acpi device:18: GPIO: looking up reset-gpio
[ 12.273711] acpi device:18: GPIO: _DSD returned device:18 0 0 0
[ 12.273737] gpio gpiochip0: Persistence not supported for GPIO 14
[ 12.273960] usbcore: registered new interface driver btusb
Change-Id: I14e3ef099d5b8f48c915b41284039b3508dec975
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Tune I2C bus3 frequency and insure it meets I2C spec.
BUG=b:161650117
TEST=flash coreboot to the DUT and actual measured I2C bus3
make sure it meet Spec.
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Ifa9f0bce723f55a12fd2313788c995f8326e3e7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This applies what commit 79572e4f32f844f60338d1aafdba6b94f4111a5c does
to the devicetree settings of the zork devices.
Change-Id: Ife94818d771f137e56c51ad1598148f60fcf5345
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43820
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:161923068
Change-Id: I67f23c0602e345fbd806e661a4462cf07f93ef64
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43783
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since FSP pre-populates the UPD struct with the non-zero default values,
coreboot shouldn't set them to zero in the case that they aren't
configured in the board's devicetree. Since all parameters being zero is
a valid case, this patch adds another devicetree option that applying
the devicetree settings for the USB2 PHY tuning depends on being set.
BUG=b:161923068
Change-Id: I66e5811ce64298b0644d2881420634a8ce1379d7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43781
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Raydium ACPI entry currently provides a reset GPIO and an _ON/_OFF
method to the kernel. These are contradictory. The ownership of the GPIO
should be mutually exclusive between either the OS or the FW. Since we
have two methods exposed this causes the OS to reset the TS twice. Once
using the _ON method, and once using the GPIO. Additionally the _ON
method is waiting for 20ms after reset while the OS driver uses a 50ms
delay. The Raydium TS datasheet specifies 20ms for FW ready time, so the
OS driver is adding additional padding.
The reference design has a 32ms rise time on the reset line. So without
this patch, the OS tries to reset the TS using the _ON method and it
waits for 20ms. This is not enough time for the reset line to reach
high, let alone account for the FW ready time. The OS driver then tries
to reset the device by toggling the GPIO. It waits 50ms which is still
2ms less than required.
This CL removes the GPIO from being exported in the _CRS so the OS
driver won't try and reset the device. It also increases the reset delay
by 32ms to account for the rise time.
This isn't a complete fix. I think that the slow rise time is causing
some kind of metastability in the TS reset hardware. Using a script to
bind and unbind the TS driver, the TS device becomes unresponsive after
~200 iterations. The only way to reset the device is to power cycle.
The TS power is also not currently controlled by the power resource.
This means that we have no guarantee over when the reset line is
toggled. This will lead to issues while spending and resuming.
BUG=b:160854397
TEST=Boot trembyle and make sure TS works. Suspend/Resume trembyle 300+
times.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I23131be5d7109eed660a8bd6e2c156c015aa3c4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Earlier versions of Dalboz did not correctly handle HS400. One fix was
to add stitching vias, but these boards did not have them. b/156539551
Another possible fix is to add tuning parameters including drive
strength, but that is still a WIP. b/158959725
This should correct OS load failures in the meantime by running the bus
slower.
BUG=b:158845662
TEST=build, flash, boot sku 0x5a80000c to OS
BRANCH=None
Signed-off-by: Eric Peers <epeers@google.com>
Change-Id: Ia3e7a641bde04c5a7be29bf91c38dd8c110ed17a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43572
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the dirinboz variant of the dalboz reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:161579679
BRANCH=master
TEST=util/abuild/abuild -p none -t google/zork -x -a
make sure the build includes GOOGLE_DIRINBOZ
Change-Id: I33c03080ffbe0bca61acf4144417b9f5fff6389f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change does the following:
a. USI_REPORT_EN is no longer set to high in coreboot. Instead
GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this
pad as required.
b. Appropriate delays are added for power-down sequencing:
- Delay after REPORT_EN is disabled - 1ms
- Delay after RESET is asserted - 1ms
BUG=b:159501288
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: If4d12fa0d4f4e5123d8fdccdabda996dcafa4523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Morphius uses Goodix touchscreen and not G2 touchscreen. This change
updates hid and desc properties in devicetree accordingly.
BUG=b:159501288
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I2527fa5409bb127ac225c6fb2a5f1bc24895f6cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPIO_91 is added to ACPI using the device tree entry for codec. So,
this change drops the TODO from GPIO table.
Change-Id: I9c2e91465ab554126531f8512028360ae5fb316d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change configures all missing pads in ramstage for dalboz
reference. This ensures that the state of all pads is set correctly
for the payload/OS. Also, all the pads for the platform are configured
in baseboard gpio table in ramstage to ensure that variants can
override any pads if required.
BUG=b:154351731
Change-Id: Ia30da908d3827177a7b3594ffba38bff81018ab9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change configures all missing pads in ramstage for trembyle
reference. This ensures that the state of all pads is set correctly
for the payload/OS. Also, all the pads for the platform are configured
in baseboard gpio table in ramstage to ensure that variants can
override any pads if required.
BUG=b:154351731
Change-Id: Idd827b6a4f995546493596f22249f8699bdf526b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops PULL_UP configured on pads in early_gpio table since
these pads have external pulls.
BUG=b:154351731
Change-Id: Id270e7b4f83dfa942655f513776a3b1c15c9678d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Most of the DXIO descriptors are used to configure PCIe engines and
lanes, but on Picasso system some of the DXIO lanes can also be
configured as SATA or XGBE ports.
Change-Id: I28da1b21cf0de1813d87a6873b8d4ef3c1e0e9dd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43675
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The lane numbers in the PCIe/DXIO descriptor are the logical and not the
physical ones, so add logical to the corresponding field names of the
fsp_pcie_descriptor struct.
Change-Id: I7037fed225119218e87593932815aff815e83ff8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update Woomax configuration including GPIO, memory SPD table, I2C devices
and USB type C.
BUG=b:158343602
BRANCH=None
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I55ba995d9438551d45cb9e17f92b5089ccf4a5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change drops the pulls configured on override GPIOs as they
already have external pull-ups. Also, pads which are unused are
configured as PAD_NC.
BUG=b:154351731
Change-Id: I8da5d51af25bbe2694c21ecb0868c9cc387243cb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
These methods are empty and the kernel treats these as optional.
BUG=b:153001807, b:154756391
TEST=Suspend and resume trembyle
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5f2b375c1186951f95b7ac44dc7158a0299013a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43465
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops internal pulls for dalboz reference configured on pads
which already have external pull-ups in hardware.
GPIO_0(PWR_BTN_L): Pulled up to PP3300_A
GPIO_2(WAKE_L): Pulled up to PP3300_A
GPIO_10: Unused. Changed to PAD_NC.
GPIO_11(EC_IN_RW_OD): Pulled up to PP3300_A
GPIO_12(USI_INT_ODL): Pulled up to PP3300_A
GPIO_16(USB_OC0_L): Pulled up to PP3300_A
GPIO_17(USB_OC1_L): Pulled up to PP3300_A
GPIO_21(EMMC_CMD): Pulled up to PP1800_S0
GPIO_22(EC_FCH_SCI_ODL): Pulled up to PP3300_A
GPIO_31(EC_AP_INT_ODL): Pulled up to PP1800_A
GPIO_32: Unused. Changed to PAD_NC.
GPIO_113(I2C2_SCL): Pulled up to PP3300_S0
GPIO_114(I2C2_SDA): Pulled up to PP3300_S0
GPIO_129(KBRST_L): Pulled up to PP1800_S0
GPIO_92(CLK_REQ0_L): Pulled up to PP3300_S0
GPIO_115(CLK_REQ1_L): Pulled up to PP3300_S0
GPIO_116(CLK_REQ2_L): Pulled up to PP3300_S0
BUG=b:154351731
Change-Id: I62e9dbac7a55efa1e055983a7c126168ee516151
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops internal pulls for trembyle reference configured on pads
which already have external pull-ups in hardware.
GPIO_0(PWR_BTN_L): Pulled up to PP3300_A
GPIO_2(WAKE_L): Pulled up to PP3300_A
GPIO_10: Unused. Changed to PAD_NC.
GPIO_12(USI_INT_ODL): Pulled up to PP3300_A
GPIO_16(USB_OC0_L): Pulled up to PP3300_A
GPIO_17(USB_OC1_L): Pulled up to PP3300_A
GPIO_21(EMMC_CMD): Pulled up to PP3300_A
GPIO_22(EC_FCH_SCI_ODL): Pulled up to PP3300_A
GPIO_31(EC_AP_INT_ODL): Pulled up to PP1800_A
GPIO_90: Unused. Changed to PAD_NC.
GPIO_113(I2C2_SCL): Pulled up to PP3300_S0
GPIO_114(I2C2_SDA): Pulled up to PP3300_S0
GPIO_129(KBRST_L): Pulled up to PP1800_S0
GPIO_130(EC_IN_RW_OD): Pulled up to PP3300_S0
GPIO_92(CLK_REQ0_L): Pulled up to PP3300_S0
GPIO_115(CLK_REQ1_L): Pulled up to PP3300_S0
GPIO_132(CLK_REQ4_L): Pulled up to PP3300_S0
BUG=b:154351731
Change-Id: Id84b801e019eede7ef543c24aac968f3ef99b3fd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43526
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Vilboz requires a different HID than rest of the zork variants. Hence,
this change sets the HID to AMDI1015 for I2S machine device in vilboz
overridetree.cb.
BUG=b:157708581
Change-Id: Ibae343f21cf8f0c782dc8a461f69172bf0da7eba
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43545
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change switches zork devices to use the newly added
i2s_machine_dev driver in devicetree rather than passing
dmic_select_gpio in SoC config.
BUG=b:157708581
Change-Id: I76c633694cbfb454c081ab2a4af4765bfbbae16b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops mainboard.asl from zork because none of the objects
defined in it are used.
BUG=b:153879530
Change-Id: If5440bcbce39b4461b44acaec69561663b1ea329
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43519
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Global variable `PMOD` that stores the interrupt mode used by OS is
required by all mainboards. This change moves the variable definition to
globalnvs.asl under picasso.
Additionally, ACPI spec says that BIOS should assume interrupt mode as PIC
until _PIC() method is called by OS. Thus, this change also updates the
default value of PMOD as 0 i.e. PIC mode.
BUG=b:153879530
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I731c03d965882281a7a23f55894451210ba72274
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43514
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO_9 is associated with gevent 22. Correct all the misconfigurations
and use macros for clarity as to what bit offset is being used instead
of open coding things.
BUG=b:161205804
Change-Id: Ic4cfd62763d72d12a55f89585f24e07df6af0f4f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables ACP_PME_EN and ACP_I2S_WAKE_EN for dalboz and trembyle
boards using devicetree settings.
BUG=b:161328042,b:146317284
Change-Id: Ie367a9ba878a1892177df874bbcb8005efeb0880
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43496
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
commit 56da63c3dc3f50cfac541c779b608e1bae9e635c removed overriding that
field in the FADT.
Change-Id: I0c8ff9ab125129dc856949c47a3a0c14e4109c73
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43417
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The kernel already clears this: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/master:src/third_party/kernel/v5.4/drivers/acpi/acpica/hwregs.c;l=390
No reason to have the firmware do it as well.
BUG=b:153001807, b:154756391
TEST=Build Trembyle, boot, suspend, and resume and didn't see any ACPI
errors.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia5c79fb95dc885eaef8abc4257b6ba18c1ef1b66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
PMx0EE is not defined in the Picasso PPR.
BUG=b:153001807, b:154756391
TEST=None
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I98caf0cd2d0bdcf19de2b945dcf74f5cf7354769
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
On zork, bootblock is part of RW firmware in non-recovery mode, so PCIe
GPIOs can be configured early on in bootblock rather than waiting until
romstage. This change moves the call to variant_pcie_gpio_configure() to
happen in bootblock and drops romstage.c file.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic515304f35fe5623d58d6000efcb11fb9039e137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43476
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
gpio_set_stage_rom table is now configuring only PCIe related GPIOs in
romstage. This change moves the configuration of PCIe related GPIOs to
variant_pcie_gpio_configure() to keep all the configuration for WiFi and
non-WiFi PCIe pads in one place. It also drops the function
variant_romstage_gpio_table() as it is unused.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib1c41ba141dce6b52b6e0a250a3aa07c296068aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43475
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the power and reset GPIO configuration for non-PCIe devices is
dropped from romstage GPIO table, the tables for pre-v3 and v3 version of
schematics are exactly same. So, this change drops the duplicate table and
also removes the check for v3 schematics when configuring the pads in
romstage.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I67ca9f587c3f47912393ebaf38badcc9d76cc393
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops power and reset control for non PCIe devices in
romstage for dalboz reference as this is not required.
+---------------------------------------------------------------------------------------+
| GPIO| Net name | External| Internal| Domain| State at reset | State on S3 resume |
| # | | Pull | Pull | | | |
+---------------------------------------------------------------------------------------+
| 5 | PEN_POWER_EN | 100K PD | PD | S5 | Powered off | Powered on |
| | | | | | (because of | (since power is not|
| | | | | | internal PD) | disabled when |
| | | | | | | entering S3) |
+---------------------------------------------------------------------------------------+
| 6 |EN_PWR_TOUCHPAD| 499K PD | PU | S5 | Powered on | Powered on |
| | | | | | (because of | (since trackpad |
| | | | | | internal PU) | is wake source) |
+---------------------------------------------------------------------------------------+
| 68 | EMMC_RESET_L | 100K PU | PD | S0 | Asserted | Asserted |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
| 76 | EN_PWR_CAMERA | 499K PD | PD | S0 | Powered off | Powered off |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
| 140 | USI_RESET | 10K PD | PD | S0 | Deasserted | Deasserted |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
| 141 | USB_HUB_RST_L | 10K PU | PD | S0 | Asserted | Asserted |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
+---------------------------------------------------------------------------------------+
| 67 |EN_PWR_TOUCHPAD| 10K PU | PD | S0 | Powered off | Powered off |
| |_PS2 (pre-V3) | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
GPIO_140 starts deasserted out of reset and S3 resume, but gets
asserted in ramstage since it is eventually deasserted by OS using
ACPI methods.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ie792a5a9d6420763ff10d1e475c094b6ee514888
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops power and reset control for non PCIe devices in
romstage as this is not required.
+---------------------+--------------------------------------------+--------------------+
| GPIO| Net name | External| Internal| Domain| State at reset | State on S3 resume |
| # | | Pull | Pull | | | |
+---------------------------------------------------------------------------------------+
| 5 | PEN_POWER_EN | 100K PD | PD | S5 | Powered off | Powered on |
| | | | | | (because of | (since power is not|
| | | | | | internal PD) | disabled when |
| | | | | | | entering S3) |
+---------------------------------------------------------------------------------------+
| 13 |EN_PWR_TOUCHPAD| 499K PD | PU | S5 | Powered on | Powered on |
| |_PS2 | | | | (because of | (since trackpad |
| | | | | | internal PU) | is wake source) |
+---------------------------------------------------------------------------------------+
| 68 | EMMC_RESET_L | 100K PU | PD | S0 | Asserted | Asserted |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
| 76 | EN_PWR_CAMERA | 499K PD | PD | S0 | Powered off | Powered off |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
| 140 | USI_RESET | 10K PD | PD | S0 | Deasserted | Deasserted |
| | | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
+---------------------------------------------------------------------------------------+
+---------------------------------------------------------------------------------------+
| 67 |EN_PWR_TOUCHPAD| 10K PU | PD | S0 | Powered off | Powered off |
| |_PS2 (pre-V3) | | | | (because of | (because of |
| | | | | | internal PD) | internal PD) |
| | | | | | | |
+-----+---------------+---------+---------+-------+----------------+--------------------+
GPIO_140 starts deasserted out of reset and S3 resume, but gets
asserted in ramstage since it is eventually deasserted by OS using
ACPI methods.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ieadc62f1a13857209cf0a62f204efb9278e0e97d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change keeps USI_RST(GPIO_140) asserted in ramstage since it gets
deasserted by OS using ACPI methods.
BUG=b:160854397
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I8feced788e471a0efb2358d42b2146df04fb7a0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43461
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change keeps pen power enabled in sleep state to allow it to
charge in S3.
BUG=b:155422911
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I6190496653878327f34a01f6a743db474d32e929
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43452
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This information is redundant since it's already specified in
baseboard/devicetree_trembyle.cb or baseboard/devicetree_dalboz.cb
domain 0 is still required because sconfig uses it as an identity anchor
to match devicetree and overridetree.
BUG=b:157580724
TEST=Boot zork, usb functional
Change-Id: I3c3c1c2410166b99599d7343fae3ee756f4da321
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no reason to create a named variable. We can just return the
package.
BUG=b:153001807, b:154756391
TEST=None
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4f8f0362adf5ea5f026d0ba5ac6ac917fa160142
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The ACPI specification, version 2.0 says:
_BFS is an optional control method.
So, remove them. They have been copy-pasted around quite a bit, and do
not do anything useful. Plus, it's deprecated in later ACPI versions.
Change-Id: I9ef21f231dd6051d410ac3a0fe554908409c2fa7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43443
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Morphius cannot support 100Mhz fast SPI causing it to not boot.
Downgrade all zork boards to fast=66mhz and normal=33mhz to be safe.
BUG=b:161233767
TEST=Boot morphius
Change-Id: I7744dd0cb8dede985fbdc28a64385e0bc4048402
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43459
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Eric Peers <epeers@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add USB ports, USB user-facing camera and USB bluetooth to devicetree.
USB ports 4 and 5 are duplicated for picasso and dali.
BUG=b:158096224
TEST=Boot Trembyle and Dalboz, Dump acpi tables
Change-Id: Icf8628d91e27a3afdc5fd67a53b44089c809da87
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split zork baseboard devicetree between dalboz and trembyle.
The devicetree is simply duplicated, no other changes in this commit.
BUG=b:158096224
TEST=Build coreboot for zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I5b26770790092c69db9567fa4337edd21a6ed809
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
CB:43224 ("mb/google/zork: Add helpers for v3 schematics and wifi
power enable") added helper functions for determining if a board uses
v3 schematics. However, it introduced a regression by adding a wrong
check for variant_uses_v3_schematics() in variant_audio_update(). This
change fixes the check to ensure that dmic_gpio is updated when
variant is not using v3 schematics.
BUG=b:161141258,b:161128964
TEST=Verified on trembyle that trackpad works again (it was broken
because of the regression).
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I0e6ad844f68cface7b545f1547bd94470c30dde4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43415
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the woomax variant of the zork reference board by copying
the template(coreboot-zork/util/mainboard/google/trembyle)
files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:158343602
BRANCH=None
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I0bb8ce1851f4064d24e48fd8957e2f9fe1e80b53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change SPI speed from 66MHz, mode 1-1-2 to 100MHz mode 1-2-2.
“1-2-2" means command, address and data are transmitted
through 1 wire, 2 wire and 2 wire, respectively.
BUG=b:160603142
TEST=Boot on trembyle, verify register settings.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I14f96e3c085126c70e64ef3a3f5b7b54ce6cbffe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43306
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This matches the other methods.
BUG=b:154756391
TEST=Build trembyle
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ba1fc5756c17da4dc1727425af17c4582c01a18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Zork devices shut down the i2c controllers in S3 to save power. On
resume, they need to be enabled in verstage before being accessed or
the system hangs.
BUG=b:160834101
TEST=Resume works with psp_verstage.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7b8c7e12847876dab4ca74d67d3c41e63d7727cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43334
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This code is not even being build-tested. Drop it before it grows moss.
Change-Id: I6f71419ea23b973b0bedb426e20cb3dc460ef68d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43271
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the selection of VARIANT_SUPPORTS_PRE_V3_SCHEMATICS
for Vilboz since it did not have any build with pre-v3 schematics.
Change-Id: I3919ad43e1dae95a4fa71073e83865e92f30dfec
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43225
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds following two helper functions:
1. variant_uses_v3_schematics() - Check whether the variant is using
v3 version of schematics.
2. variant_has_active_low_wifi_power() - Check whether the variant is
using active low power enable for WiFi.
In addition to this, Kconfig options are reorganized to add two new
configs - VARIANT_SUPPORTS_PRE_V3_SCHEMATICS and
VARIANT_SUPPORTS_WIFI_POWER_ACTIVE_HIGH. This allows the helper
functions to return `true` early without checking for board version.
Eventually, when a variant decides to drop support for pre-v3
schematics, it can be dropped from selecting
VARIANT_SUPPORTS_PRE_V3_SCHEMATICS. Similarly, when the variant
decides to drop support for active high power enable for WiFi, it can
be dropped from selecting VARIANT_SUPPORTS_WIFI_POWER_ACTIVE_HIGH.
Change-Id: I62851299e8dd7929a8e1e9a287389abd71c7706c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43224
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves the configuration of GPIO_137 to happen in ramstage
since there is nothing in coreboot that requires the state of write
protect GPIO for zork.
Change-Id: Ibaf8e7d9dd5d13a9b39b10ac0174de345b8380f5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43223
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change removes "write protect" entry from the list of GPIOs
shared with depthcharge as done for other Chrome OS boards in CB:39318.
Change-Id: Ibd39e8d6835e465b2ab5eebcc245e45db5d84deb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43222
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Finally enable psp_verstage for zork.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: If6a12c2074d7c84c0cb766393c66f5eff29a58d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Update GPIOs since Vilboz hardware design
follow schematic V3.2, so gpio.c is unnecessary.
BUG=b:157744136
BRANCH=NONE
TEST=flash the bios to vilboz DUT and test touchpad function
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I575f8b233b56185f3281ad7127bc274bda5ea801
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42986
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
At this moment, Vilboz board version is 1 and it
according to v3+ schematics, however WiFi power enable
is active high. This change sets
VARIANT_MIN_BOARD_ID_V3_SCHEMATICS for Vilboz as 1
and VARIANT_MIN_BOARD_ID_WIFI_POWER_ACTIVE_LOW as 2.
BUG=b:160547115
BRANCH=None
TEST=flash the bios to vilboz DUT and test WIFI module
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I9699bb839a801ab7d14c38b971ec28e3a322a997
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
update telemetry value for SDLE test result.
BUG=b:152922299,b:152369472
TEST=emerge-zork coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I14d218243931271ba15ec4113e9bc46c670fb2ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42999
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, the telemetry settings are not for the pollock platform
and might causethe power and performance issue. so applied the Pollock
reference board settings to Dalboz to improve the performance,
and the values need to be updated after the SDLE test finished.
BUG=b:157961590,b:152922299
TEST=Build.
Change-Id: I0da5b81afaa5814c13ec0257dc0eb3471be94c29
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2228257
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42998
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Apply the default USB2 phy tuning parameter for Zork family
BUG=b:155132211
TEST=Build, verified the default value been applied on trembyle
and the USB2 device works well.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I1f00b04173796d70147e232bafa405487b0761e1
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2260216
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42997
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the check for ENV_RAMSTAGE in mainboard_ec_init()
since it is included only in ramstage. Also, the content of
ramstage_ec_init() is moved into mainboard_ec_init().
Change-Id: I282fb07a80f4de6064a544f6dd58e8f973a597b9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43118
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
mainboard_ec_init() does nothing in any stage other than ramstage. So,
this change drops the call to mainboard_ec_init() from
romstage.c. Additionally, it also drops ec.c from romstage and
verstage.
Change-Id: Iae0be4d678b0780cf532000a6c0fff1bce333c0e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43117
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
