Age | Commit message (Collapse) | Author |
|
From spec, [31:28] "HS DC Voltage Level Adjustment" is "TXVREFTUNE0".
correct rx_vref_tune -> tx_vref_tune
BUG=None
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I27003a952d8f8bdd8fe52af8a37010e23ee9cdfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:172846122
TEST=./util/abuild/abuild
Change-Id: I75a92616f11054993ff5a5bfefce5c3f4638c07c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use command below to change the variable globally.
sed -i "s/\<variable\>/variable_u/g" `grep variable -rl ./ \
--exclude-dir=build --exclude-dir=crossgcc`
BUG=b:171334623
TEST=Build
Change-Id: I056a76663e84ebc940343d64178c18cb20df01a3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since google_chromeec_cbi_get_board_version and google_chromeec_cbi_get_fw_config both call cbi_get_unit32 and return 0 as success, non-zero as failure. Let's add more readability for the false condition.
BUG=None
TEST=check with empty CBI value
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia49ac1ee35302f8f6afe8c0eb8e13afdf36c5b2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46566
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD Slope: 62852 -> 62641
SOC Slope: 28022 -> 28333
BUG=b:170531252
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id831907aa47be27fef2e33bb884a1118ffec14a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Enhance USB 2.0 SI by increasing the level of "HS DC Voltage Level"
and "Disconnect Threshold Adjustment".
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:162614573
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 registers are set correctly
3. test with servo v4 type-c, it's working expectedly.
4. U2 SI pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I278cc0aaddbc9fce595bf57ca69ee8abfc9f5659
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46537
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
BUG=b:168265881
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Id6c4f1a92d7f2ad293df7b63694e9665b85f8018
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46472
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on morphius with and without patch, confirm ~7ms improvement
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I7f6efd3d5839f154f2487a07654be8e35634bbbc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45932
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In morphius, the USB3 typeA port needs to set to gen1, and for ezkinil
all the USB3 ports should force to gen1. So set the corresponding
setting to usb3_port_force_gen1 to force USB3 to Gen1.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I10419b91fe86fe3e06de36ddfe0d1769c1031f8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add support for trackpoint wakeup from S3 by adding device events to
mainboard and defining for morphius.
BUG=b:160345665
BRANCH=zork
TEST=tested trackpoint wake from S3 on morphius DVT
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I982f0f4b60fbaeb389774531e1dee83da77cb8a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Morphius has SSD/eMMC SKU, we should turn off eMMC
if storage is NVMe SSD.
BUG=b:169211959
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I67d5d77ce3d827ae89b82529de59925f67eaf894
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
clamshell/tablet:
Slow_ppt_limit(W) 20
Fast_ppt_limit(W) 24
Slow_ppt_time_constant 5
Stapm_time_constant 200
Sustained_power_limit(W) 12
clamshell:
Temperature limit(C') 100
tablet:
Temperature limit(C') 70
BUG=b:157943445
BRANCH=zork
TEST=1. emerge-zork coreboot
2. change mode and check "thermctl_limit" will change
Change-Id: I1eda1411766e446b673046236f7cc4015696521f
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45520
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add dptc interface in devicetree for morphius.
Set the STAPM parameters for tablet mode:
dptc_enable = 1
dptc_fast_ppt_limit = 24000
dptc_slow_ppt_limit = 20000
dptc_sustained_power_limit = 6000
BUG=b:157943445
BRANCH=zork
TEST=Build. check the setting changed.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I4dac4b7e5157ad7ad407f42a6fc6b06eefbf3291
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fingerprint interrupt (FPMCU_INT_L) is level triggered and not edge
triggered. Also, we are using GEVENT for wake from fingerprint and
not the GPIO IRQ wake. Thus, the irq property exposed in ACPI tables
does not need to be set to indicate wake for the IRQ.
This change updates GPIO table to configure the pad as level triggered
and drops the wake attribute for irq_gpio in overridetree.
BUG=b:165612778
BRANCH=zork
TEST=Verified that fingerprint still works in S0 and to wake device
from S3.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I9007e5b0882ac1a6770db52d651218998f6d750d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Allow comments prefixed with '#' in mem_parts_used csv file.
BUG=None
TEST=Run gen_part_id with mem_parts_used file containing comments
Change-Id: Ia9e274d45aa06dea7a3a5f8cd1c8ee2b23398876
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO_144 is REPORT_EN pin for the touchscreen controller where 1 means
enable operation and 0 means stop operation. Override tree exposes
this pin as stop GPIO. Thus, it needs to be configured as active low
i.e. 0 = active (stop), 1 = inactive (enable report).
Change-Id: I349123655260349b78d2f75f846da0ce1dc966fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
v3.6+ of reference schematics have moved to using active low polarity
for touchscreen GPIO. This change sets the default polarity in
override tree accordingly to active low. To support boards from older
builds, variant_touchscreen_update() already updates the polarity to
active high.
BUG=b:161937506
Change-Id: I370bdb27ea5d0601612d13b515113a6048018964
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Switch all zork boards to use generated generic SPDs from spd_tools.
HMAA1GS6CMR6N-VK is unused by Ezkinil, and all other boards, so it was
removed.
picasso/Makefile.inc was updated to populate the 2nd APCB channel based
on APCB_POPULATE_2ND_CHANNEL. This removes the need to suffix spd
entires with _x1/_x2.
Command to generate files:
$ find src/mainboard/google/zork/variants/ -maxdepth 1 -type d | grep -v '/$' | while read b; do
n=$(basename ${b});
if [ "${n}" = "baseboard" ]; then
continue
fi
go run util/spd_tools/ddr4/gen_part_id.go src/mainboard/google/zork/spd \
src/mainboard/google/zork/variants/${n}/spd \
src/mainboard/google/zork/variants/${n}/spd/mem_parts_used.txt
done
BUG=b:162939176
TEST=Boot ezkinil and dalboz check dmidecod -t17
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I0553858f83d3d1e90cf35bece108768f004a29a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44480
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The USB OC pin mapping is similar enough to move it to the base board
and just have two overrides for trembyle, which is based on an older
version of the schematics, and one override for woomax, which doesn't
use one USB port.
BUG=b:163081097
Change-Id: I7e305d7e6f51d7ef7a4c699e3bacc6bcd699d2f2
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GPIO_89 was marked as EN_DEV_BEEP_L in pre-v3.6 schematics, but it was
never really used on any of the zork variants. Starting with v3.6,
GPIO_89 is left unused in schematics.
This change configures GPIO_89 as PAD_NC in baseboard GPIO
table. Since EN_DEV_BEEP_L still needs to be driven high to allow
speakers to work, GPIO_89 is configured as PAD_GPO driven high on
pre-v3.6 schematics.
BUG=b:62108046
Change-Id: I026cd6cb598667ce6e115c3ec9357a6a56051d39
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44190
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for touchscreen power control using:
* GPIO_90 for trembyle based boards
* GPIO_32 for dalboz based boards
By default, baseboard tables configure these GPIOs as PAD_GPO driven
low and override trees expose these pads as enable_gpio to be used by
ACPI power resource.
In order to support pre-v3.6 boards, override tables configure these
pads as PAD_NC and drop the enable_gpio setting from device tree based
on board version.
BUG=b:161935640, b:162747210
Change-Id: Iba5e36b65b44ea11613b4d5fc8f13ce6433f83ab
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44193
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
v3.6 of reference schematics have switched the polarity of reset
signal to touchscreen controller from active high to active low. This
change updates the default configuration in baseboard gpio tables to
set the reset GPIO to output low and override tables in variants to set the
reset GPIO to output high. Additionally, devicetree by default exposes
ACTIVE_LOW configuration for reset GPIO. In order to support pre-v3.6
boards, reset GPIO is updated to ACTIVE_HIGH based on board version.
BUG=b:161937506
Change-Id: I092f274d8eb1920a1cd6d3eccbe8f26b0b28928a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:162010077
Change-Id: Iba3e3ec62cdfd818077017abd28fa754c2ae7797
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change does the following:
a. USI_REPORT_EN is no longer set to high in coreboot. Instead
GPIO_144 is exposed as stop_gpio in ACPI to allow OS to control this
pad as required.
b. Appropriate delays are added for power-down sequencing:
- Delay after REPORT_EN is disabled - 1ms
- Delay after RESET is asserted - 1ms
BUG=b:159501288
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: If4d12fa0d4f4e5123d8fdccdabda996dcafa4523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Morphius uses Goodix touchscreen and not G2 touchscreen. This change
updates hid and desc properties in devicetree accordingly.
BUG=b:159501288
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I2527fa5409bb127ac225c6fb2a5f1bc24895f6cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change configures all missing pads in ramstage for trembyle
reference. This ensures that the state of all pads is set correctly
for the payload/OS. Also, all the pads for the platform are configured
in baseboard gpio table in ramstage to ensure that variants can
override any pads if required.
BUG=b:154351731
Change-Id: Idd827b6a4f995546493596f22249f8699bdf526b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change drops the pulls configured on override GPIOs as they
already have external pull-ups. Also, pads which are unused are
configured as PAD_NC.
BUG=b:154351731
Change-Id: I8da5d51af25bbe2694c21ecb0868c9cc387243cb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
These methods are empty and the kernel treats these as optional.
BUG=b:153001807, b:154756391
TEST=Suspend and resume trembyle
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5f2b375c1186951f95b7ac44dc7158a0299013a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43465
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops mainboard.asl from zork because none of the objects
defined in it are used.
BUG=b:153879530
Change-Id: If5440bcbce39b4461b44acaec69561663b1ea329
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43519
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO_9 is associated with gevent 22. Correct all the misconfigurations
and use macros for clarity as to what bit offset is being used instead
of open coding things.
BUG=b:161205804
Change-Id: Ic4cfd62763d72d12a55f89585f24e07df6af0f4f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43516
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This information is redundant since it's already specified in
baseboard/devicetree_trembyle.cb or baseboard/devicetree_dalboz.cb
domain 0 is still required because sconfig uses it as an identity anchor
to match devicetree and overridetree.
BUG=b:157580724
TEST=Boot zork, usb functional
Change-Id: I3c3c1c2410166b99599d7343fae3ee756f4da321
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43437
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the inclusion of codec.asl in DSDT for `GOOG0013`
device and instead uses the newly added Chrome EC audio codec driver
for filling in the device node in SSDT.
TEST=Verified that following node gets generated:
Scope (\_SB.PCI0.LPCB.EC0.CREC)
{
Device (ECA0)
{
Name (_HID, "GOOG0013") // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
Name (_DDN, "Cros EC audio codec") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
}
Change-Id: I3e626ce01a3735ac2c966c0e95310be4c828b241
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43042
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for pen insert/eject operations in S0 and
wake on pen eject from S3 for morphius.
BUG=b:158814699,b:158719244
Change-Id: I3530a0aa83ec69559436687205c64524b862799b
Signed-off-by: Kevin Chiu <kevin.chiu@quanta.corp-partner.google.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
update telemetry to improve the performance.
BUG=b:154863613
BRANCH=master
TEST=emerge-zork coreboot
Change-Id: Ia08259e81f360259f23ea0f9c5c128c9d0961322
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add Samsung K4A8G165WC-BCWE x2
BUG=b:159418770
BRANCH=master
TEST=emerge-zork coreboot
Change-Id: I200a1074d3c9fe79a8a2c69f42b0612e745f36f5
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change replaces variant_wifi_romstage_gpio_table() with
variant_pcie_power_reset_configure() to handle the reset and power
sequencing for WiFi devices pre- and post- v3 version of schematics.
These are the requirements that need to be satisfied:
1. As per PCI Express M.2 Specification Revision 3.0,
Version 1.2, Section 3.1.4 "Power-up Timing", PERST# should stay
disabled until `TPVPGL` time duration after device power has
stabilized. Value of TPVPGL is implementation specific.
2. For Intel WiFi chip, it is known to get into a bad state if the
above requirement is violated and hence requires a power cycle.
3. On pre-v3 schematics:
- For both dalboz and trembyle references, GPIO42 drives
WIFI_AUX_RESET_L which is pulled up to PP3300_WIFI.
- For both dalboz and trembyle references, PP3300_WIFI is controlled
using GPIO29. This pad gets pulled high by default on PWRGOOD
because of internal pull-up. But, at RESET# it is known to have a
glitch. When GPIO29 gets pulled high, it causes WIFI_AUX_RESET_L to
be pulled high as well. This violates the PCIe power sequencing
requirements. Hence, for pre-v3 schematics on both dalboz and
trembyle, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET_L.
b. Disable power to WiFi.
c. Wait 10ms to allow WiFi power to go low.
d. Enable power to WiFi.
e. Wait 50ms as per PCIe specification.
f. Deassert WIFI_AUX_RESET_L.
4. On v3 schematics:
- For trembyle: WIFI_AUX_RESET_L is driven by GPIO86 which has an
internal PU as well as an external PU to PP3300_WIFI.
- For dalboz: WIFI_AUX_RESET is driven by GPIO29. This is active
high and has an internal PU. It also has an external 1K PD to
overcome internal PU.
- For both dalboz and trembyle references, PP3300_WIFI is
controlled by GPIO42 which has an internal PU and external
PD. Trembyle schematics have a comment saying strong PD of 2.2K but
the stuffed resistor is a weak one (499K). ON dalboz, it uses a
weak PD (which doesn't look correct and instead should be a strong
PD just like trembyle). Having a strong PD ensures that the WiFi
power is kept disabled when coming out of G3 until coreboot
configures GPIO42 as high.
- Thus, for v3 schematics, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET{_L} signal.
b. Enable power to WiFi.
c. Wait 50ms as per PCIe specification.
d. Deassert WIFI_AUX_RESET{_L} signal.
BUG=b:157686402, b:158257076
TEST=Verified that QCA and AX200 cards both continue working. Tested
QCA on Dalboz and Trembyle. Tested AX200 on morphius.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I532131ee911d5efb5130d8710f3e01578f6c9627
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42738
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the baseboard GPIO table in ramstage to match v3
version of trembyle reference schematics. All variants using this
reference are accordingly updated to configure the GPIOs that changed
as part of v3 schematics.
BUG=b:157088093, b:154676993, b:157098434
TEST=Compiles
Signed-off-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib1d6ee2e995c1fca229c20ea63da9a45fb89f64a
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/third_party/coreboot/+/2251393
Reviewed-by: Aaron Durbin <adurbin@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42724
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds support for fingerprint device in overridetree for
the following variants:
1. berknip
2. morphius
3. trembyle
Generates the following node in SSDT1:
Scope (\_SB.FUR1)
{
Device (CRFP)
{
Name (_HID, "PRP0001") // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
Name (_DDN, "Fingerprint Reader") // _DDN: DOS Device Name
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
UartSerialBusV2 (0x002DC6C0, DataBitsEight, StopBitsOne,
0x00, LittleEndian, ParityTypeNone, FlowControlNone,
0x0040, 0x0040, "\\_SB.FUR1",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Level, ActiveLow, ExclusiveAndWake, PullDefault, 0x0000,
"\\_SB.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0006
}
})
Name (_S0W, 0x04) // _S0W: S0 Device Wake State
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x0A,
0x03
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x01)
{
Package (0x02)
{
"compatible",
"google,cros-ec-uart"
}
}
})
}
}
BUG=b:147853944
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7ccb3633332ce3e388293872af7b22f1867c8465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This is a copy of the mb/google/zork directory from the chromiumos
coreboot-zork branch. This was from commit 29308ac8606.
See https://chromium.googlesource.com/chromiumos/third_party/coreboot/+/29308ac8606/src/mainboard/google/zork
Changes:
* Minor changes to make the board build.
* Add bootblock.c.
* Modify romstage.c
* Removed the FSP_X configs from zork/Kconfig since they should be
set in picasso/Kconfig. picasso/Kconfig doesn't currently define the
binaries since they haven't been published. To get a working build
a custom config that sets FSP_X_FILE is required.
BUG=b:157140753
TEST=Build trembyle and boot to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3933fa54e3f603985a0818852a1c77d8e248484f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41581
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|