| Age | Commit message (Collapse) | Author |
|---|
|
ACPI_GPIO_IRQ_EDGE_BOTH sets both edges as wake. The desired behavior is wake on rising edge, change to ACPI_GPIO_INPUT_ACTIVE_LOW.
Fixing for both Volteer and Volteer2 variants.
BUG=b:146083964
BRANCH=None
TEST=tested on a Volteer
Change-Id: I2d3339151bf4e2cbae60aaf97ba1bd7909a2b9a9
Signed-off-by: Alex Levin <levinale@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Update ELAN i2c-hid touchpad configuration
BUG=b:160741785
BRANCH=None
TEST=Verify touchpad is working fine.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2549048766d0707666910bd86c46ac9201bf3905
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43998
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is expected TCSS D3Hot is enabled. D3Cold configuration is
through SoC stepping determination. D3Cold is disabled on pre-QS
platform and enabled on QS platform.
BUG=None
TEST=Verified both of TCSS D3Hot and D3Cold configuration on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I9a8b838dcb449ca78d15b18543d97d84b59417ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44004
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dq/dqs mappings based on voxel schematics.
BUG=b:155062561
BRANCH=none
TEST=FW_NAME=voxel emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ida248094a1477fe457026e18f313385082ee71f0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43794
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If59502aec7c3ab55864a518d626cde52aee18373
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43746
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This copies over the USB daughterboard device tree config from volteer
to volteer2. These two boards are basically identical in this area so
the config should also be identical.
BUG=b:158673460
TEST=none
Change-Id: If8a82bc18b36d92a1c851b49612edfbefa18ec54
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Todor is created to take the place of terrador therefore
copying terrador content into todor's setup.
BUG=b:162110806
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TODOR
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I63151728a04f2252ca8a77158a2656ad8b1e1b51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Create the todor variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
In addition,
* sort the variant names in alphabetical order.
* todor uses the same config options as terrador.
BUG=b:162110806
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TODOR
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: I7aa7acf1f3c3cc14b92ded05d5868818a627a432
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Create the eldrid variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:162115131
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_ELDRID
Signed-off-by: MiceLin <mice_lin@wistron.corp-partner.google.com>
Change-Id: I1cd07ee7a87335e1e0b51d65c26bffc3bc46037c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Use gpio_keys driver to add ACPI node for pen eject event. Also
setting gpio wake pin for wake events.
Removal and insertion (both edges) triggers IRQ and only removal is a
wake event (rising edge).
Adding for both Volteer and Volteer2 variants.
BUG=b:146083964
BRANCH=None
TEST=tested on a Volteer
Change-Id: Ida3217a5b156320856ce3302c2623eba2230f28d
Signed-off-by: Alex Levin <levinale@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43764
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update delbin configuration include GPIO, memory SPD table, I2C devices
and USB type C.
BUG=b:158797761
BRANCH=None
TEST=emerge-volteer coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I59ce4720e0ffeeeb2c9440bb300686def80211ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42301
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update ELAN i2c-hid touchpad configuration
BUG=b:160741785
BRANCH=None
TEST=Verify touchpad is working fine.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I098d8a305c6e04af1562a545ff4af6383665798b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's a `GPL-2.0-or-later` version of this file in volteer2, so use it
in place of these weirdly-licensed files.
Change-Id: Icde2f6539d9c726d6967350f74e7bc015e01e7b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set power limits in devicetree for Tiger Lake Y-SKU based volteer
variant boards.
BUG=b:152639350
BRANCH=None
TEST=Built and tested power limits on volteer variant board.
Change-Id: If4f1226473b48365e5962df9fff29910c99007fc
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43607
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In the middle of the Great DPTF Refactor of 2020, new volteer variants
were added, but their dptf.asl files are no longer used, so delete them.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I52f2042aa870a29026eb9fe122340ad07654e706
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
While the DPTF refactor was in progress, TSR3 was added to volteer's
dptf.asl file, and I forgot to update the devicetree with TSR3 as well.
Also missed a swap in the passive policies of TSR0 and TSR1. This patch
fixes those.
BUG=b:149722146
TEST=boot volteer, dump SSDT & DSDT, verify TSR3._STA returns 0xF
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I71bc798492ec45bb1e2f8d779e6829db52ef4499
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Enable SataPortsEnableDitoConfig for port 1.
BUG=b:151163106
BRANCH=None
TEST=Build and boot volteer.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I552faaa0e7172e77208025cf4251bb848cc90709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42415
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SaGv needs to be enabled for only QS. On ES2, we are seeing system
instability.
BUG=b:159198381
TEST=Tested for boot. Power and performance tests were run with
volteer2 with qs setup. System showed stability.
Tested for boot stability on on delbin.
Change-Id: I1bce3b9f837fb19ba5a20ae31750a73474a86788
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Configure volteer2 and delbin, the two variants currently using
preQS or QS silicon, to use CSE Lite.
BUG=b:158140797
TEST=cd to volteer's asset_generation folder, execute
"./gen_all_variant_images.sh" and verify that all variant
images are produced.
Change-Id: I5e444529b090d82094b9da0df2648ea4cdb2888e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
Change-Id: I964c53afbd503d47a07b982672425f0e7a986a3f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41895
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:160711124
TEST="FW_NAME=ripto emerge-volteer coreboot chromeos-bootimage"
and verify that the build does not fail.
Change-Id: Ic132256a192b8cb77662963bea844f193eb912d9
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Windows definition
There was a review comment for Chromium Linux ov2740 driver that
Windows driver already set the HID as INT3474 and suggested to have
the same value for Chrome.
The upstreamed Linux driver code has INT3474 as HID and this patch is
to set the same HID in ACPI configuration.
https://patchwork.kernel.org/patch/11540753/
BUG=b:160334865
BRANCH=none
TEST=User-facing camera should work with the driver which set the HID
as INT3474
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I10e98d32899f31d91c1cc7ddfa099af73d8aef37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43006
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer world-facing camera has a privacy LED and it is supposed
to be turned on only when the camera is being used. But the LED
is always on and this is to fix the issue.
RCAM_SNR_PWR_EN (RearCAMera_SeNsoR_PoWeR_ENable) GPIO, which
controls the world-facing camera LED, was not in the power-up
and power-down sequence definitions and this caused the issue.
BUG=b:160341981
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check the world-facing camera LED is only turned on only when
the camera is working.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I564690baffddfdd0f998525992643aaf16ba4b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42985
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on schematic and gpio table of terrador, generate gpio settings
and overridetree.cb for terrador.
BUG=b:156435028,b:151978872
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Verify that the image-terrador.bin is generated successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4bf9081b034bc4cd566dde45586be8309cdbb4a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42302
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds memory parts used by variant terrador to
mem_list_variant.txt and generates DRAM IDs allocated to these parts.
Added memory
1. MT53E512M64D4NW-046 WT:E
2. MT53E1G64D8NW-046 WT:E
BUG=b:159195585,b:152936481,b:156435028
TEST="emerge-volteer coreboot chromeos-bootimage", flash terrador and
verify terrador boots to kernel.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia14f76e9cb0df64961d46f4b61b39439e56f6a8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41995
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable HotPlug for the PCIe root port that the SD express is on so the
OS can re-train the link without needing a reboot if it goes down
unexpectedly at runtime.
BUG=b:156879564
BRANCH=master
TEST=enable HotPlug on Volteer Root Port 7 (SD express) and check in
linux that it is identified as a HotPlug capable root port
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: Ie9d427dd297567f06123119a670b5ed2e1f73701
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42897
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CB:43090 renamed con to conn to avoid issues when building on Windows.
CB:42905 introduced more uses of the old name.
Adapt the latter to comply with the former.
Change-Id: I723141add5452fc541f67cb8591793f2d64cc231
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43141
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on schematic and gpio table of voxel, generate gpio settings
and overridetree.cb for voxel.
BUG=b:157879197,b:155062762
TEST=FW_NAME=voxel emerge-volteer coreboot chromeos-bootimage
Verify that the image-voxel.bin is generated successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I49c1923e63d87f11de362fd893905ac2f1137bba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
The USB-C SBU and HSL orientation configuration depends on the USB
daughterboard used on the system. This patch adds an additional
configuration for supporting passive USB daughterboards using "probe"
directives to select the appropriate configuration at runtime.
BUG=b:158673460
TEST=verified active USB DBs enumerate at USB3 speeds in linux
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Change-Id: Ia4bd97de8f974531f97469a5e47ecf4d948beca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
For historical reasons, Windows has issues with certain names being
used for files and directories, 'con' or 'CON' being one of
them. Therefore, rename the pmc_mux/con driver to pmc_mux/conn in
order to work around this issue.
TEST=built volteer (only user of this driver as of now)
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ia78dc4efe647c96a7169a3b95fc3b8944d052c83
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
BUG=b:158140797
TEST=build and boot volteer with CSE Lite SKU
Cq-Depend: chrome-internal:3100721
Change-Id: I4f939883617a1271b30c76d41e61113bbdd6ab5b
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42070
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature.
BUG=None
BRANCH=None
TEST=Built for volteer platform and verified the MSR value
Change-Id: I6438547e09a3ff3a1c01addfcc01383e89f5b435
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This is to enable Intel ME communication interface HECI1 by
devicetree for PAVP with CSE Lite.
BUG=b:159615125
TEST=Build and boot volteer. Run lspci and check pcie device
00:16.0 Communication controller: Intel Corporation Device a0e0
Change-Id: I68eb51c6a0af77982c060767993265764a2bc926
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1) Based on malefor schematics, disable unused I2C port, USB port, TBT
PCIe
2) Add audio device to the tree
BUG=b:150653745, b:154973095
TEST=FW_NAME=malefor emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the devices' function worked properly.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: I9ce465705e8b8f67ddbc9e4eb06c5a8bfac65fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42246
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the volteer2 variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
Modified to alphabetize and update to duplicate latest volteer changes
currently in the review and merge pipeline.
Added the following missing files from the variants/volteer2/ folder:
- gpio.c
- include/variant/acpi/dptf.asl
- acpi/mipi_camera.asl
- Makefile.inc
- memory/dram_id.generated.txt
- memory/Makefile.inc
- memory/mem_list_variant.txt
- overridetree.cb
BUG=b:159135047
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLTEER2
Change-Id: I987c72b83dc993af248a753a2caa56be0f26c1ad
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42605
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the delbin variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
BUG=b:158797761
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_DELBIN
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Change-Id: Icf5fc6b9cc6a7c47e52103b2d396bcddb26adf50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable CmdMirror for Terrador to achieve optimum routing from SoC to
DRAMs
BUG=b:156435028
BRANCH=none
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0db9fff0dddf35c99a6cb2a90d40886ed8e18686
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Remove an unneccessary comment and group the variant_early_gpio_table
together based on GPIO group.
Changed static variable name gpio_table to override_gpio_table to be
more descriptive.
BUG=none
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer to kernel.
Change-Id: Iabe810df1e5a3df35e3543ab81b9fdb6f76c223a
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42577
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the following volteer-specific devices from baseboard's
devicetree.cb into volteer's overridetree.cb file:
- Goodix Touchscreen
- ELAN Touchscreen
- ELAN Touchpad
- SAR0 Proximity Sensor
Adjust the other variant's overridetree.cb files to correspond to
the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959
TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot
volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update fw_config definition in devicetree.cb to match current
definition for volteer.
BUG=b:159157584
TEST=none
Change-Id: I761893818231880d86fd13cfa61319157d06a7d5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42331
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The pass through mode (SW CM) RTD3 is not supported until QS platform.
D3Cold is needed to be disabled along with upstream TBT firmware
signed_TGL_HR_4C_A0_rev6_pre4_SW_CM_PM_support_ENG_VER_perst_check_fix.
This temporary patch will need to be reverted once PM RTD3 support is
validated on QS platform.
BUG=b:159050315
TEST=Verfiy PM S0ix along with upstream TBT firmware.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I98ed991e4185abf1f3168e33b099e0e97c9075f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42504
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Divya Sasidharan <divya.s.sasidharan@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using guidance from Intel, a new set of power limits (PL1, PL2 & PL4)
are available for TGL-U. They are dependent upon the SKU of the CPU
that the mainboard is running on. Volteer is updated here to use these
new limits.
To accomplish this, the SoC chip config's power_limits_config member
was expanded to an array, which can be indexed by POWER_LIMITS_*_CORE
macros. Just before power limits are applied, the correct set of them
is chosen from the array based on System Agent PCI ID. Therefore, a
TGL board should have two sets of power limits available in the
devicetree.
BUG=b:152639350
TEST=On a Volteer SKU4 (4-core), verified the following console output:
CPU PL1 = 15 Watts
CPU PL2 = 60 Watts
CPU PL4 = 105 Watts
Change-Id: I18a66fc3aacbb3ab594b2e3d6e2a4ad84c10d8f0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
TGL RVP and Volteer use ov8856 camera module from different vendors.
TGL RVP from Foxlink and Volteer from Sunny. ov8856 sensor is identical
for the two modules but VCM and EEPROM are different. Originally,
Volteer ACPI was set to align with Sunny module, GT9679. But it turned
out GT9679 is compatible with Foxlink's DW9768. So Volteer camera ACPI
configuration doesn't need to keep GT9679.
BUG=b:158188369
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check user-facing camera functionalities.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I792608f86a59b16545dfa4edf6508de7a444bb26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Add unique new acpi device ids for dptf for Tiger Lake soc based platforms
and update volteer speficic dsdt.asl file accordingly. The Linux kernel
driver expects these new acpi device ids for dptf functionalities.
BUG=None
BRANCH=None
TEST=Build and boot on volteer system
Change-Id: I7dbb812c0fc0f5084c98cf2752ce7ddce8e4d50e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Kconfig 4.17 started using the $(..) syntax for environment variable
expansion while we want to keep expansion to the build system.
Older Kconfig versions (like ours) simply drop the escapes, not
changing the behavior.
While we could let Kconfig expand some of the variables, that only
splits the handling in two places, making debugging harder and
potentially messing with reproducible builds (e.g. when paths end up
in configs), so escape them all.
Change-Id: Ibc4087fdd76089352bd8dd0edb1351ec79ea4faa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
It is the reference board of TGL-Y platform, we want to disable EC SW
sync for Proto stage, it would be re-enabled before EVT stage.
BUG=b:156435028
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie7999e24e9c173d4870b35ce1728f3dcc8dcac29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42090
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:157567939
TEST="emerge-volteer coreboot chromeos-bootimage", flash and
boot volteer to kernel.
Change-Id: I3046cf3a359e833a5d204f78ab84312e8665061f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42411
Reviewed-by: Jes Klinke <jbk@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Temporary workaround for S0ix issues related to FSP's handling of 0 value.
When IomTypeCPortPadCfg is 0 FSP completely skips any flow related to this
value which seems to be causing issues with s0ix.
This is still being debugged and a final solution will be made when available
BUG=b:159151238
TEST=flash image with workaround to volteer and verify that s0ix
cycles correctly.
Change-Id: Id79dd1c49958389cdb666b3760abd821bc1973a8
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42268
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If there is no installed audio daughter board on volteer then the
HDA driver in the kernel will crash on resume. In order to prevent
this disable the PCI device when AUDIO=NONE probe match is true.
BUG=b:147462631
TEST=boot on volteer and ensure that the PCI device at 0:1f.3 is gone
Change-Id: I4a436e1b76418030bf635427e490b54a713fdd33
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dq/dqs mappings based on terrador schematics.
BUG=b:156435028,b:151978872
BRANCH=none
TEST=FW_NAME=terrador emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I97697a3dd9b88eaffe6e2b1be7bd346979cbc956
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enables the fourth thermal sensor for fan in DPTF for volteer
BRANCH=None
BUG=b:149722146
TEST= On volteer system check
`cat /sys/class/thermal/thermal_zone5/type` for TSR3
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: Ie11496828133aa71f1017f759516e2e5d3dff2d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
This change adds memory parts used by variant voxel to
mem_list_variant.txt and generates DRAM IDs allocated to these parts.
This variant is not yet supported by coreboot but DRAM IDs need to be
generated for it. In the coming days, variant voxel will be added to
coreboot.
BUG=b:157732528
Change-Id: I8780beec987deb8fed11bb8f84275dcba4768514
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
For Volteer mainboard, this patch set optimized values for PCH external
VR settings and ext rail voltage/current, to achieve better power
savings in sleep states.
v1p05 and vnn power rails can be used as an alternative source
by-passing vccin_aux during Sx. This by-pass feature, enables us to
shutdown vccin_aux rail which is higher voltage rail compared to v1p05
and vnn. These both rails were disabled by default in FSP. Changes in
this patch are:
1. v1p05 and vnn rails are enabled and enabled supported voltage types
in S0i1, S0i2, S0i3, S3, S4, S5 states. They were disabled by default.
2. Icc Max for v1p05 changed to 500 mA from default 100 mA.
3. vnn rail's voltage is changed to 5 V from default 4.2 V.
BUG=None
BRANCH=None
TEST="Build and boot volteer and check VR settings with Intel ITP-XDP
debugger and verify approx 250 mW power savings in Sx"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib46423872c956af9aaa92902fce552d5447237c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42223
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF_TSR2_SENSOR_ID to 2. Fixes the issue where TSR1 and
TSR2 have the same DPTF_TSR#_SENSOR_ID value causing them to
report the same temperature under /sys/class/thermal
and also swap TSR0 and TSR1 in DTRT to match physical sensor
in volteer schematics
BRANCH=None
BUG=b:149722146
TEST=On volteer system check TSR1 and TSR2 temperatures, should
report different values
`cat /sys/class/thermal/thermal_zone[3,4]/temp`
Also verify other TSRs using `cat /sys/class/thermal/thermal_zone*/temp`
and `ectool tempsinfo all ; ectool temps all`
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: Idc5f35e4faf59b0ee726eb32a08eab4654fb342d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42232
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Move the GPIOs that are likely to be volteer-specific (mostly
peripherals) to reside in variants/volteer/gpio.c so that
variants don't have to override too many GPIO settings.
- Modify malefor's gpio.c to adjust for the changes to baseboard's
gpio.c.
- Remove unused GPP_C3 (USB4_SMB_SCL) and GPP_C4 (USB4_SMB_SCA)
settings.
- Remove unused GPP_D9, GPP_D10, GPP_D11, and GPP_D12 settings.
- Remove unused GPP_E8 (SLP_S0IX), COEX, WWAN, and SNDW related
settings for malefor.
- Remove unused GPP_R4 (HDA_RST_L) setting.
BUG=b:157597158
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer SKU4 to kernel.
Change-Id: Ib2f384f539d55a3a8d4a7608336ef22aca3d8c4f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Now that volteer is moved to using the auto-generated SPDs, we no
longer need the spd/ folder under each variant. Hence, this change
drops the spd/ folders and the SPD files within them.
BUG=b:156126658
Change-Id: Icb36adeb11fd68a84df5b225db32fb8d840a530f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41619
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change switches volteer and family to using auto-generated SPDs
obtained using gen_spd.go and gen_part_id.go.
BUG=b:147321551,b:155423877
Change-Id: I9ed48f0b51714b072a0459d0b70b5417a49db54f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
gen_part_id.go
This change adds mem_list_variant.txt that contains the list of
memory parts used by volteer and Makefile.inc generated by
gen_part_id.go using mem_list_variant.txt.
In the final change of the series, all volteer variants will be
switched from using the current SPDs to new auto-generated SPDs.
Differences in auto-generated SPD from current SPD are as follows:
Part: K4U6E3S4AA-MGCL
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
Part: K4UBE3D4AA-MGCL
Byte# Current New Explanation
6 0xB5 0xB4 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
Part: H9HCNNNBKMMLXR-NEE
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. tckMin is
calculated as (1/4267)*2 which comes
out to be 0.46871. Some datasheets
round this down to 0.468 and others
round it up to 0.469. JEDEC spec uses
0.468. As per that, this value comes
out to be 0xE0.
Part: H9HCNNNFAMMLXR-NEE
Byte# Current New Explanation
4 0x15 0x16 As per datasheet, density is 16Gb per
logical channel. So value should be 0x16.
6 0xF9 0xB8 This device has 4 logical dies
instead of 8. Also, signal loading is
not used by MRC.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
20,21, 0x92,0x55, 0x12,0x29, As per datasheet, part supports CAS
22 0x00 0x15 latencies 6,10,16,22,26,32,36,40. So value
should be 0x12,0x29,0x15.
24 0x8C 0x96 taa is .468ns * CAS-40 which results
in byte 24 being 0x96 as per datasheet.
29,30 0xE0,0x0B 0xC0,0x08 As per datasheet, this corresponds to
280ns in MTB units which is 0x08C0.
31,32 0xF0,0x05 0x60,0x04 As per datasheet, this corresponds to
140ns in MTB units which is 0x04C0.
123 0x00 0xE2 Fine offset for taa. Expected value
is 0xE2 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. tckMin is
calculated as (1/4267)*2 which comes
out to be 0.46871. Some datasheets
round this down to 0.468 and others
round it up to 0.469. JEDEC spec uses
0.468. As per that, this value comes
out to be 0xE0.
Part: MT53E1G32D2NP-046 WT:A
Byte# Current New Explanation
4 0x15 0x16 As per datasheet, density is 16Gb per
logical channel. So value should be 0x16.
5 0x21 0x29 As per datasheet, this part has 17row
address bits and 10column address
bits. This results in 0x29.
6 0xB5 0x94 This device has 2 logical dies. Also,
MRC does not use signal loading.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
12 0x0A 0x02 As per datasheet, this is 1rank and
16-bit wide channel. So, value should
be 0x02.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
29,30 0xC0,0x08 0xE0,0x0B As per datasheet, this corresponds to
380ns in MTB units which is 0x0BE0.
31,32 0x60,0x04 0xF0,0x05 As per datasheet, this corresponds to
190ns in MTB units which is 0x05F0.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
BUG=b:147321551,b:155423877
Change-Id: I3998b2cd91020130bacf371fce9b0d307304acbe
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
gen_part_id.go
This change adds mem_list_variant.txt that contains the list of
memory parts used by halvor and Makefile.inc generated by
gen_part_id.go using mem_list_variant.txt.
In the final change of the series, all volteer variants will be
switched from using the current SPDs to new auto-generated SPDs.
Differences in auto-generated SPD from current SPD are as follows:
Part: H9HKNNNCRMBVAR-NEH
Byte# Current New Explanation
4 0x16 0x15 As per datasheet, density is 8Gb per
logical channel. So value should be 0x15.
6 0xB9 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00. 2 channels 2
dies. Hence, 0x94
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
29,30 0xE0,0x0B 0xC0,0x08 As per datasheet, this corresponds to
280ns in MTB units which is 0x08C0.
31,32 0xF0,0x05 0x60,0x04 As per datasheet, this corresponds to
140ns in MTB units which is 0x0460.
125 0xE1 0xE0 Fine offset for tckMin. tckMin is
calculated as (1/4267)*2 which comes
out to be 0.46871. Some datasheets
round this down to 0.468 and others
round it up to 0.469. JEDEC spec uses
0.468. As per that, this value comes
out to be 0xE0.
Part: MT53E1G64D4SQ-046 WT:A
Byte# Current New Explanation
5 0x21 0x29 As per datasheet, this part has 17row
address bits and 10column address
bits. This results in 0x29.
6 0xB9 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00. 2 channels,
2 dies. Hence, 0x94.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
BUG=b:147321551,b:155423877
Change-Id: I28b065a00380516d8686279a92ef68b9f17e2f65
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41616
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
gen_part_id.go
This change adds mem_list_variant.txt that contains the list of
memory parts used by malefor and Makefile.inc generated by
gen_part_id.go using mem_list_variant.txt.
In the final change of the series, all volteer variants will be
switched from using the current SPDs to new auto-generated SPDs.
Differences in auto-generated SPD from current SPD are as follows:
Part: K4U6E3S4AA-MGCL
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Bits 1:0 set to 0.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
BUG=b:155239397,b:147321551
Change-Id: I8b8bdc55314f538aff4dd1944a0b745357744d8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41615
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
gen_part_id.go
This change adds mem_list_variant.txt that contains the list of
memory parts used by ripto and Makefile.inc generated by
gen_part_id.go using mem_list_variant.txt.
In the final change of the series, all volteer variants will be
switched from using the current SPDs to new auto-generated SPDs.
Differences in auto-generated SPD from current SPD are as follows:
Part: K4U6E3S4AA-MGCL
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Bits 1:0 set to 0.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
BUG=b:155239397,b:147321551
Change-Id: Ibb06443a5c7fd80915f66b806cdd7c3ae1275b05
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41614
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the voxel variant of the volteer reference board
BUG=b:157879197
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOXEL
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I8ba5412be211730db84675927c500238cb20ff3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Based on schematic and gpio table of halvor, generate gpio setting and
overridetree.cb for halvor.
BUG=b:153680359
TEST=FW_NAME=halvor emerge-volteer coreboot chromeos-bootimage
Verify that the image-halvor.bin is generated successfully.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ic6bd018551be58945742d1a6e7f7c5560f218e40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The ripto board is still being used for testing so make sure it supports
the same audio config as volteer.
BUG=b:147462631
TEST=build ripto variant
Change-Id: Iabeb73307418dc16b12fa60ad26923cd9f6e1f3a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
For all of the audio devices in devicetree.cb add the probe matches
that will determine if the device should be enabled or not based on
the selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357 and alc5628, disable others
AUDIO=MAX98373_ALC5682I_I2S: enable max98373 and alc5682, disable others
AUDIO=MAX98373_ALC5682_SNDW: enable soundwire devices, disable others
BUG=b:147462631
TEST=test different device present in ACPI based on fw_config value:
> AUDIO=NONE
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682I_I2S
ectool cbi set 6 0x00000200 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000300 4 2
Change-Id: I5492e8cddcff3ba01023b0daef02be3508d347b0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41216
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the current firmware configuration table for the volteer mainboard
and define some actions based on probe results for audio:
- When I2S options are selected disable the SoundWire GPIOs.
- When SoundWire is enabled disable the I2S GPIOs.
- When no audio is enabled disable all the GPIOs.
BUG=b:147462631
TEST=Test that GPIOs are configured as expected based on the current
value of the fw_config field in cbi.
Change-Id: I179f8b6436be83a2b37911777764bd26a0d404b7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41215
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Move all audio devices from baseboard to the volteer variant.
- Add max98373 devices and enable the driver
- Disable everything in FSP and let coreboot configure GPIOs.
BUG=b:147462631
TEST=this change makes all audio devices show up in ACPI, so this
was tested by ensuring that all audio devices are present in ACPI.
Change-Id: Ic654ea52a549053622603aa8c81fb37577d4e011
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This explicitly enables TCSS DMA0 controller and disables
TBT PCIe2 and PCIE3 since they are unused on volteer.
BUG=:b:146624360
TEST=Built and booted on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I05cc9e3964d8037d433fca443be6e8d5b444bbce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41387
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer's MUX connections are known, and can now be described in ACPI
tables. Port 1 has the only oddity, with SBU lines staying fixed in the
CC1 orientation.
TEST=Dump SSDT tables on Volteer, and confirm (coalesced for brevity):
Scope (\_SB.PCI0.PMC)
{
Device (MUX)
{
Name (_HID, "INTC105C")
Device (CON0)
{
Name (_ADR, 0)
Name (_DSD, Package() {
Package () { "usb2-port-number", 9 },
Package () { "usb3-port-number", 1 },
})
}
Device (CON1)
{
Name (_ADR, 1)
Name (_DSD, Package() {
Package () { "usb2-port-number", 4 },
Package () { "usb3-port-number", 2 },
Package () { "sbu-orientation", "normal" },
...
}
}
}
Change-Id: Id361b2df07e87ad72b6a59a686977b3f424e8ecf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
ports""
This reverts commit 1726fa1f0ce474cde32e8b32be34a212aff3ffba.
Reason for revert: Resource allocator is split into old(v3) and
new(v4). So, this change to enable hotplug resource allocator for
volteer can land back.
BUG=b:149186922
Change-Id: Ib6a4df610b045fbc885c70bff3698a032b79f770
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create the terrador variant of the volteer reference board
BUG=b:156435028
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_TERRADOR
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I088861d1f8b7b4ee8de1e5ab6c7d3109ffd0531b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
There are SX9310 devices present in devicetree.cb but the driver is
not enabled so it is not getting used.
Change-Id: I625233013a2e14eaf758e56027774fbf5df3bc83
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41700
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert spaces to tabs in volteer variant makefiles, and remove empty
comment lines from file headers.
BUG=none
TEST="emerge-volteer coreboot chromeos-bootimage", flash and verify
volteer boots to kernel.
Change-Id: I6c818c3adcc55ce89707efff6dd9a6bce512daa5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41587
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In Tiger Lake we have support for enabling MIPI clocks at runtime in
ACPI. Hence remove setting pch_islclk from devcietree and chip.h.
Also update functions which reference pch_isclk.
BUG=b:148884060
Branch=None
Test=build and boot volteer and verify camera functionality
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I6b3399172c43b4afa4267873ddd8ccf8d417ca16
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41570
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This explicitly enables both of TCSS D3HotEnable and D3ColdEnable
from Volteer devicetree.cb setting.
BUG=:b:146624360
TEST=Built and booted on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I1a168ad87169c0f6633704c55c9293aa25710188
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
BUG=b:156990317
TEST=emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the ELAN trackpad can wake up unit from suspend.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: If4bea8a9742f7533be2e51b855cc39ca77d73608
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable drivers for SoundWire codecs and define the topology in
the devicetree for the volteer variant with the SoundWire daughter
board connected.
+------------------+ +-------------------+
| | | Headphone Codec |
| Intel Tigerlake | +--->| Realtek ALC5682 |
| SoundWire | | | ID 1 |
| Controller | | +-------------------+
| | |
| Link 0 +----+ +-------------------+
| | | Left Speaker Amp |
| Link 1 +----+--->| Maxim MAX98373 |
| | | | ID 3 |
| Link 2 | | +-------------------+
| | |
| Link 3 | | +-------------------+
| | | | Right Speaker Amp |
+------------------+ +--->| Maxim MAX98373 |
| ID 7 |
+-------------------+
This was tested by booting the firmware and dumping the SSDT table
to ensure that all SoundWire ACPI devices are created as expected with
the properties that are defined in coreboot under \_SB.PCI0:
HDAS - Intel Tigerlake HDA PCI device
HDAS.SNDW - Intel Tigerlake SoundWire Controller
HDAS.SNDW.SW01 - Realtek ALC5682 - Headphone Codec
HDAS.SNDW.SW13 - Maxim MAX98373 - Left Speaker Amp
HDAS.SNDW.SW17 - Maxim MAX98373 - Right Speaker Amp
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I7782059807416369e0e1ba0d4d7c79dcab0fcbc5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40894
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of only using the baseboard devicetree add a placeholder
overridetree for volteer and refer to it in Kconfig.
This will allow us to add the volteer specific devices here instead
of at the baseboard level.
BUG=b:146482091
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: I7788a5473fc2275a9791fb27e0e4018a0efcd0f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40893
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DRAM Max Cycle Time (tCKmax) for Samsung's K4UBE3D4AA-MGCL DRAM
part should be set to 0xF.
BUG=b:157178553, b:156555863
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot a
SKU4 volteer to the kernel and run "memtester 6G 100" and verify it
completes successfully without error and does not crash.
Change-Id: Id95b19fe261e3f57a52a43055acab99af66b14ab
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41634
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPD_LPDDR4X_200b_8bank_1Rx16_16Gb_DDP_4267.spd.hex SPD
contained an incorrect SDRAM Max Cycle Time (0 instead of 0x0f).
After fixing that error, I noticed that two generic SPDs could
be collapsed into one, so I removed one of the duplicate generic
SPDs (SPD_LPDDR4X_200b_8bank_1Rx16_16Gb_16Row_DDP_4267.spd.hex),
and changed Makefile to collapse volteer's DRAM ID 2 into ID 0.
BUG=b:156126658, b:156058720
TEST=Flash and boot a ripto to kernel. Also verified that ripto
can boot successfully to the kernel at 4267 MT/sec with FSP built
in debug mode with RMT enabled.
Change-Id: Ib52bf674ebf91854d3d078015aa640aa7ee98a6f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41345
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DPTF functionality for volteer platform
BRANCH=None
BUG=b:149722146
TEST=Built and tested on volteer system
Change-Id: I385fb409ccd291d97369295ff99f21c9430880f9
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41427
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Historically in coreboot, the PMC's fixed PCI resources were described
by the System Agent (the MMIO resource), and eSPI/LPC (the I/O
resource). This patch moves both of those to a new Intel SoC-specific
function, soc_pmc_read_resources(). On TGL, this new function takes care
of providing the MMIO and I/O resources for the PMC.
BUG=b:156388055
TEST=verified on volteer that the resource allocator is aware of and
does not touch these two resources:
("PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran 0 limit 0
flags f0000200 index 0
PCI: 00:1f.2 resource base 1800 size 100 align 0 gran 0 limit 18ff
flags c0000100 index 1")
Also verify that the MEM resource is described in the coreboot table:
("BIOS-e820: [mem 0x00000000fe000000-0x00000000fe00ffff] reserved")
Verified the memory range is also untouchable from Linux:
("system 00:00: [mem 0xfe000000-0xffffffff] could not be reserved")
Change-Id: Ia7c6ae849aefaf549fb682416a87320907fb3fe3
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41385
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Link frequency and a format was not correct for volteer proto 2
ov2740 user-facing camera.
The link frequency is calculated in the following way.
(max frame width * max frame height * max fps * data format in bps
/ number of lanes / data rate) + max 35% of overhead
For ov2740, (1920 * 1080 * 60 * 10 / 2 / 2) = 311Mhz.
360Mhz after adding 18% of overhead.
BUG=b:148428976
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check user-facing camera functionalities.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I3b51826e123dec394c1b4eb9a1c5b64b8b11459e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41157
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Volteer port 0 (MB PORT) does not have a retimer so the port needs
to be configured for the SOC to handle Aux orientation flipping. This
requires 2 changes setting the TcssAuxOri UPD to 1 for port 0 (Bit 0)
and configuring AUXP and AUXN GPIOs to Native Function 6 so SOC can
control the orientation
BUG=b:145220205
BRANCH=NONE
TEST=booted Volteer proto 2 and verified that the AUX channels flip
when the cable is flipped
Change-Id: Ic81adc24d10322cc305bf0fa4c38514468ea0942
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
This enables EC software sync in romstage.
BUG=b:148259137
TEST=verified EC is updated in romstage using coreboot serial console
logs.
Change-Id: Ibb97c1d57220f7fd74131a5aee450b1ab4b1c982
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41078
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per schematics configure headset interrupt as
edge both for ripto and volteer baseboard.
BUG=b:147085988
BRANCH=none
TEST=Build and boot ripto board. Test that jack functionality
is working fine and also confirm with evtest.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I8e1625140ccf55db8cb0fe3c039f1c31c01069b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 2412924bc7646fc22b2cb1b9108413fa3e849082.
Reason for revert: Resource allocator patches need to be reverted
until the AMD chipsets can be fixed to handle the resource allocation
flow correctly.
BUG=b:149186922
Change-Id: Iea6db8cc0cb5a0e81d176ed3199c91dcd02d1859
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41411
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on Fibocom HW user manual RESET should be deasserted at least 20ms after the power on pin.
The design for the reset pin is open drain connected to a pull up, so it is set to high-Z (configured as GPIO in) after 20ms.
BUG=b:152013143
BRANCH=none
TEST=traced the signals using a scope to verify timing is met.
Signed-off-by: Alex Levin <levinale@chromium.org>
Change-Id: I7c947d1bc4cce1f97383a2f2c254986e182661c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables PCIEXP_HOTPLUG to support resource allocation for
TCSS TBT/USB4 ports.
BUG=b:149186922
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I4cb820e83da40434b00198b934453805e35ef1ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adds SPD_LPDDR4X_556b_1R_32Gb_8GbD_QDP_4267.spd.hex, which will be used
initially for the "H9HKNNNCRMBVAR-NEH" SKhynix part as DRAM ID #0.
Adds SPD_LPDDR4X_556b_1R_64Gb_16GbD_QDP_4267.spd.hex, which will be
used initially for the "MT53E1G64D4SQ-046 WT:A" Micron part as
DRAM ID #1.
BUG=b:155423877
TEST=none
Change-Id: I5580f602cd411e415dafcb36bd1ffa43c4f02f60
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41076
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Add SPD_LPDDR4X_200b_1R_16Gb_16Row_DDP_4267.spd.hex, initially
used for the SKhynix H9HCNNNBKMMLXR-NEE part with DRAM ID #2
- Add SPD_LPDDR4X_200b_2R_64Gb_ODP_4267.spd.hex, initially
used for the SKhynix H9HCNNNFAMMLXR-NEE part with DRAM ID #3
- Add SPD_LPDDR4X_200b_2R_32Gb_QDP_4267.spd.hex, initially
used for the Micron MT53E1G32D2NP-046 WT:A part with DRAM ID #4
BUG=b:147857288
TEST=none
Change-Id: I60d8bb05a4d6d3608adc7de69efc8623d1ca610d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41126
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Memory SPD files for each variant are now stored in the variant's
mb/google/volteer/variants/<variant_name>/spd directory instead
of storing them in mb/google/volteer/spd.
This change moves SPDs to where they are needed and changes the
makefile to look for them in their new locations.
BUG=b:156126658
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
a proto2 SKU4 to the kernel.
Change-Id: I759c979027477a2a4c5489a6b12278799488d6e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41184
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables the keyboard backlight feature in ACPI for volteer.
BUG=b:156326050
TEST=Verified 'KBLT' shows up in the DSDT ACPI table.
Change-Id: Id1b1bb059368b0cc36cb06e6cdb8b989060a1dde
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used commands:
perl -i -p0e 's|\/\*[\s*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-only */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*]*free[\s*]*software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*either[\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License,[\s*]*or[\s*]*.at[\s*]*your[\s*]*option.[\s*]*any[\s*]*later[\s*]*version.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-or-later */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*#]*free[\s*#]*software[;:,][\s*#]*you[\s*#]*can[\s*#]*redistribute[\s*#]*it[\s*#]*and/or[\s*#]*modify[\s*#]*it[\s*#]*under[\s*#]*the[\s*#]*terms[\s*#]*of[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*as[\s*#]*published[\s*#]*by[\s*#]*the[\s*#]*Free[\s*#]*Software[\s*#]*Foundation[;:,][\s*#]*either[\s*#]*version[\s*#]*3[\s*#]*of[\s*#]*the[\s*#]*License[;:,][\s*#]*or[\s*#]*.at[\s*#]*your[\s*#]*option.[\s*#]*any[\s*#]*later[\s*#]*version.[\s*#]*This[\s*#]*program[\s*#]*is[\s*#]*distributed[\s*#]*in[\s*#]*the[\s*#]*hope[\s*#]*that[\s*#]*it[\s*#]*will[\s*#]*be[\s*#]*useful[;:,][\s*#]*but[\s*#]*WITHOUT[\s*#]*ANY[\s*#]*WARRANTY[;:,][\s*#]*without[\s*#]*even[\s*#]*the[\s*#]*implied[\s*#]*warranty[\s*#]*of[\s*#]*MERCHANTABILITY[\s*#]*or[\s*#]*FITNESS[\s*#]*FOR[\s*#]*A[\s*#]*PARTICULAR[\s*#]*PURPOSE.[\s*#]*See[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*for[\s*#]*more[\s*#]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-3.0-or-later */|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w]*.*is free software[:;][\#\s]*you[\#\s]*can[\#\s]*redistribute[\#\s]*it[\#\s]*and\/or[\#\s]*modify[\#\s]*it[\s\#]*under[\s \#]*the[\s\#]*terms[\s\#]*of[\s\#]*the[\s\#]*GNU[\s\#]*General[\s\#]*Public[\s\#]*License[\s\#]*as[\s\#]*published[\s\#]*by[\s\#]*the[\s\#]*Free[\s\#]*Software[\s\#]*Foundation[;,][\s\#]*version[\s\#]*2[\s\#]*of[\s\#]*the[\s\#]*License.*[\s\#]*This[\s\#]*program[\s\#]*is[\s\#]*distributed[\s\#]*in[\s\#]*the[\s\#]*hope[\s\#]*that[\s\#]*it[\s\#]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
Change-Id: Ia01908544f4b92a2e06ea621eca548e582728280
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41178
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kernel pinctrl driver changed for Tiger Lake and went to old scheme.
Kernel patch: https://chromium-review.googlesource.com/c/chromiumos/
third_party/kernel/+/2116670
BUG=b:151683980
BRANCH=none
TEST=Build and boot tgl board. In /sys/kernel/debug/pinctrl
verify INTC34C5:00 listing all the pins.
Cq-Depend:chromium:2116670
Change-Id: I9f1d399ff7380125ad5b935f9590a7d9cc442b04
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39801
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Enable Goodix touch screen and ensure it works properly.
BUG=b:154191288
TEST=FW_NAME=malefor emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the Goodix touch screen function.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: I236ac56dd0a1817092151bae93e699115ba88e4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40598
Reviewed-by: Alex Levin <levinale@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
