Age | Commit message (Collapse) | Author |
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BT_DISABLE_L (GPP_A13) has to asserted in early_gpio_table to reset
bluetooth on reset.
BUG=b:171085081
TEST=volteer2 boots; scope shows assertion of the signal
Change-Id: Iaa5799e9cab69c074b7920604c8a6c85ad07358a
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:160996445
TEST=tested on delbin
Change-Id: I6ebf813c6c3364fec2e489a9742f04452be92c45
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46262
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For development of the firmware to run on the Dauntless TPM, a number of
Volteer2 devices are being reworked to replace the H1 chip with probe
wires to connect to an external Dauntless development board.
Some modification to the AP firmware is required, not least because the
Dauntless chip is connected via I2C bus, instead of SPI. Most of the
Dauntless developers will not otherwise have a Chrome OS chroot.
Because of the above, I think it makes sense to have a new variant, for
the reworked devices, which I intend to create with this CL.
BUG=b:169526865
TEST=abuild -t GOOGLE_VOLTEER2_TI50 -c max -x
Change-Id: Ibdcd6c2ce3941c229518f21f0e479890b5d76dd1
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The default GPIO values for camera power were set as 1 so the LED was
turned on by default when the board is powered on.
This status is kept until the camera is probed then being turned off.
So the LED is turned on for a few seconds during the boot up.
By setting the default power to 0, the LED is lit only when camera
is turned on for probing and this should be just a blink.
BUG=b:167635396
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it is not lit more than 0.5 seconds.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic7df391aa512daafe6e1ce49e9222b90e17ad806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45058
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_E12 should not be defined in the baseboard as its use is
determined by the variant. For legacy reasons, we still have GPP_E12
defined in early_gpio but should not. Malefor and volteer* have the
same GPP_E12 definition, but that is a misconfiguration. I think that
was a copy-paste that slipped through the reviews.
BUG=b:157597158
TEST=volteer2 boots to the OS
Change-Id: Ic3ef864827aa94b0b96e335565119f3d5d008837
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
GPP_F14 should be configured to be routed via APIC and not SCI.
BUG=b:162528549
TEST=verified on a volteer2
Signed-off-by: Alex Levin <levinale@google.com>
Change-Id: I7f2c7af230dd75b3cb3806e2b186725d49da9e68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45279
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_D16 is routed to the main power enable pin on several PCIe SD card
controllers on SD daughterboards. We should enable the power to these
chips as early as possible so they can participate in PCIe
enumeration.
BUG=b:162722965
TEST=Verified RTS5261 and GL9755 daughterboards enumerate on PCI and
can read SD cards.
Change-Id: Icf5e770f540e5d1e27b40f270bb004f4196bc7be
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
GPP_A19(DP_HPD1) and GPP_A20(DP_HPD2) were configured native function
(NF1) without internal pull-down which wrongly presents HPD interrupts.
DP_HPD had been removed for EVT design as those events are through eSPI.
This change configures GPP_A19 and GPP_A20 to be no connection and
disables DdiPort1Hpd and DdiPort2Hpd.
BUG=b:162566436
TEST=Booted to kernel and verified no kernel HPD pins assertion message
on Volteer EVT board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia3245741b776b75073d2b43d36c8ea40b476b3ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44501
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This applies to the goodix touch screen on both the volteer and
volteer2 variants: Define GPP_E3 as the stop_gpio for the touch screen
"Report_Switch" signal. Goodix defines a 1ms (minimum) delay after
stop off. In addition, no longer drive this GPIO high by default as it
is now controlled by the kernel through ACPI.
BUG=b:153705232
TEST=touch screen still functional on volteer; confirmed timings with
scope (VDD, RESET, REPORT_SWITCH)
Change-Id: I3ead9cf79812d08c4917be4585ed273050465a9b
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The latest realtek RTS5261 SD daughterboard exposes the PRSNT# pin to
GPP_D16 but there is a RTS5261 requirement to pull up this pin and not
drive it at power on. We can meet this requirement without breaking
other boards by changing GPP_D16 to be a no-connect with an internal
pull up. Other boards use this signal as an enable input, so changing
this to pull up is OK.
BUG=b:162722965
TEST=Verified RTS5261 and GL9755 daughterboards enumerate on PCI and
can read SD cards.
Change-Id: I096d76ec12b7c3afaf02e621fd301b6704913d5d
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Create the volteer2 variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.1.1).
Modified to alphabetize and update to duplicate latest volteer changes
currently in the review and merge pipeline.
Added the following missing files from the variants/volteer2/ folder:
- gpio.c
- include/variant/acpi/dptf.asl
- acpi/mipi_camera.asl
- Makefile.inc
- memory/dram_id.generated.txt
- memory/Makefile.inc
- memory/mem_list_variant.txt
- overridetree.cb
BUG=b:159135047
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLTEER2
Change-Id: I987c72b83dc993af248a753a2caa56be0f26c1ad
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42605
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|