| Age | Commit message (Collapse) | Author |
|---|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I5e07584d7857052c7a9388331a475f5a073af038
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BT_DISABLE_L (GPP_A13) has to asserted in early_gpio_table to reset
bluetooth on reset.
BUG=b:171085081
TEST=volteer2 boots; scope shows assertion of the signal
Change-Id: Iaa5799e9cab69c074b7920604c8a6c85ad07358a
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
disabling DDI port 1 and 2 HPD.
This patch adds the PMC MUX and CONx devices for lindar. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:172533907
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id5ee78b7ece8421144086af9b95f5f0d849be56c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Update lindar gpio settings for Synaptics trackpad no function issue.
Update I2C5 bus freq to 400kHz.
Improve Goodix Touchscreen power on sequence.
BUG=b:160013582
BRANCH=firmware-volteer-13521.B
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device. Verify trackpad function workable.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I8c1ab6bab1f9de187e2a78ead7b5bbaf758f5fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
According to the spec provided by Bayhub, the 3.3V power rail must be enabled at least 100ms before reset is released.
To ensure this, set the power enable signal in the bootblock GPIO table.
BUG=b:173676531
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS, test USB function normally.
Change-Id: I0c536f36c138ace93766f3024f6ec5d47b38269f
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47799
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on schematic and gpio table of lindar, generate gpio and
overridetree.cb settings for lindar.
BUG=b:161089195
TEST=FW_NAME=lindar emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Julia Tsai <julia.tsai@lcfc.corp-partner.google.com>
Change-Id: Ib869eef08433dab367edd46b3dc577190b6673d8
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
|
