Age | Commit message (Collapse) | Author |
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
GPIO D4 was used for camera reset for both front and rear cameras
(RCAM_RST_L/FCAM_RST_L) in RIPTO. For later volteer versions,
GPIO F15 is dedicated to the rear camera reset (RCAM_RST_L).
Before, BOARD_GOOGLE_VOLTEER flag was used for setting the right
RCAM_RST_L per volteer version. However, we don't support RIPTO
anymore. Also using flags for different volteer version support can
be error-prone. Removing RIPTO support.
BUG=b:171726823
BRANCH=none
TEST=Build and boot volteer proto2 or later version. Camera should
work without an issue.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I961fc17092887b4807c12c95f7139bb7e7b33e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46826
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The camera privacy LED blinks during the boot and this gives a wrong
impression to the users that the camera is being used during the power
up. The blink happens when the camera module is probed and a series of
kernel patches and coreboot patches are being submitted to resolve the
issue.
The kernel patches are submitted to the chromium gerrit.
https://chromium-review.googlesource.com/2403386
https://chromium-review.googlesource.com/2403387
https://chromium-review.googlesource.com/2403385
https://chromium-review.googlesource.com/2403384
https://chromium-review.googlesource.com/2403383
https://chromium-review.googlesource.com/2403382
https://chromium-review.googlesource.com/2403381
https://chromium-review.googlesource.com/2403380
This is to separate the power resource for the VCM so that it can be
controlled by the driver and suppress the LED turn on.
BUG=b:169049942
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check if it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Id51c98e42c5f20e231d8096c9d2d98deebc7c968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Use PCIE_CLK_NOTUSED in place of 0xFF for unused PCIe ports
BUG=none
BRANCH=master
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I35f2bbce35420fa98541a35f77b14df7440e7980
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable the USB4 retimer driver with GPP_H10 as the power control.
Change-Id: I166bc477f94c159bb411620a6bf77b5d1f194fb2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
HybridStorageMode FSP UPD needs to be set only for optane storage.
Enabling HybridStorageMode causes some extra delay in FspSiliconInit due
to HECI command and hence is avoided for NVMe and SATA scenerios. This
change disables "HybridStorageMode" for volteer baseboard. For boards
using optane HybridStorage needs to be enabled from overwrite devicetree.
We are enabling HybridStorage for volteer and volteer2 as those plaforms
have SKU's with optane storage.
BUG=b:158573805
TEST=Build and boot non optane device and confirm that FspSiliconInit
time is reduced. This saves ~100ms.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I54fc78e3f888d4f2a02ba0ad6b9aef33eb872a9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Fix typo for power limit values under comment section in baseboard
BUG=None
BRANCH=None
TEST=Build for volteer system
Change-Id: I879b9587e863360bf4efda4099d96b42b904377e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the device aliases provided by tigerlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
volteer variants.
Change-Id: I5620004afd7fa4d50389f32dd79148960a2b2662
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44039
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the SLP_Sx assertion widths and power cycle duration
for volteer.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159108661
TEST=Verified that the power cycle duration is 1~2s with a global reset
on volteer.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Idf4e0c3a60b4ac59e31df1357f2ff28f195ff17f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
cameras
There is a patch https://lkml.org/lkml/2020/9/3/235 which allows i2c
device can support driver probe without power up the device.
In order to support this, need add coreboot add
"i2c-allow-low-power-probe" property.
BUG=b:169058784
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I46f90ff8d412b18c7ee4bd7f22f9a7db771eb84f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add AC connect and disconnect to S0ix lazy wake sources.
BUG=b:161466940
BRANCH=master
TEST=Connect and disconnect charger in S0ix; observe wake
Change-Id: I30046a379ff75c33b991e355cc8d142241ee8b2e
Signed-off-by: Abe Levkoy <alevkoy@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45669
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables CnviBtAudioOffload. FSP is invoked to configure
BT over USB and BT I2S pins for cAVS connection.
BUG=b:169045123
TEST=Verifed CnviBtCore and CnviBtAudioOffload settings and FSP
configuration. Booted up to kernel on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I1780da0824d145a79743d5cffdea4821236d4f74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naveen M <naveen.m@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This sets the state of GSPI chip select to 1 (deasserted) as applied
by the FSP during the silicon init phase. GSPI 0 and 1 are set to CS
mode manual in the SerialIoGSpiCsMode section which means we need to
explicitly configure CS to deasserted in the SerialIoGSpiCsState
section. GSPI0 is the CR50 and GSPI1 is the fingerprint sensor. We
were running into problems where the normal expected CS toggle
sequence to wake up CR50 did not work because CS was already asserted
when it was expected to be deasserted, leading to TPM timeouts.
BUG=b:168090038
TEST=booted on volteer, no more "TPM flow control failure" messages;
verified fingerprint enrollment still works.
Change-Id: I47aa5db429d75e66095d58a1eb77963dcfc3b9f3
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45384
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add MAX98373_ALC5682I_I2S_UP4 firmware configuration option and configure GPIOs properly for UP4 design. The design is also for Halvor.
BUG=b:153680359, b:163382106
TEST=FW_NAME=halvor emerge-volteer coreboot chromeos-bootimage, fw_config value in Halvor:
> AUDIO=MAX98373_ALC5682I_I2S_UP4
ectool cbi set 6 0x00000400 4 2
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ie25f278dfbdc2f41a36b70403699a2e3c2234600
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add newly defined fields for presence of keyboard backlight and
number pad to the firmware configuration table.
We don't have a need to use these in coreboot (yet) but this
keeps the bit definitions in sync.
BUG=b:166707536
TEST=abuild -t google/volteer
Change-Id: I066e445f7d0be056e45737d2c538be1850ae85aa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPP_E12 should not be defined in the baseboard as its use is
determined by the variant. For legacy reasons, we still have GPP_E12
defined in early_gpio but should not. Malefor and volteer* have the
same GPP_E12 definition, but that is a misconfiguration. I think that
was a copy-paste that slipped through the reviews.
BUG=b:157597158
TEST=volteer2 boots to the OS
Change-Id: Ic3ef864827aa94b0b96e335565119f3d5d008837
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Clean up the DPTF section of the baseboard devicetree; this makes
overrides simpler, as not necessarily all of the fields need to be
overridden.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iad46fd02f7602c9419d7c3674b0d2b6f5add9a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
For Volteer (and future Tiger Lake boards) we can enable mode S0i3.4
only if we know that the Cr50 is generating 100us interrupt pulses.
We have to do so, because the SoC is not guaranteed to detect pulses
shorter than 100us in S0i3.4 substate.
A new Kconfig setting CR50_USE_LONG_INTERRUPT_PULSES controls new code
running in verstage, which will program a new Cr50 register, provided
that Cr50 firmware is new enough to support the register.
This CL adds code to detect the case when Cr50 is unable to generate
longer pulses, and in that case explicitly disable the S0i3.4 substate
as well as setting gpio_pm_override to all zeroes. This will increase
power usage slightly, but guarantee that the GPIO block in the SoC
does not switch to a slower sampling clock. In practice, this case
will only be encountered in the factory, before the Cr50 chip is
updated to a new RW image.
(Prior to this change, the gpio_pm_override was hardcoded to zero for
Volteer, but the S0i3.4 substate was not disabled. According to my
conversations with Intel engineers, that was not enough to guarantee
detection pulses shorter than 100us. But it is entirely possible that
we have just been "lucky" that the SoC has not gone into low power
mode during the boot process, where most of the cr50 communication
happens.)
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
BUG=b:154333137
Change-Id: Idef1fffd410a345678da4b3c8aea46ac74a01470
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GPP_F11 was in the early gpio table, but the definition was missing
from the main gpio_table. This change adds GPP_F11 to the gpio_table
array.
BUG=none
TEST="emerge-volteer coreboot" and verify it builds correctly.
Change-Id: I40f887300a9dfd4f8e790031b77bbee8a014f499
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
With new board designs being introduced it does not make sense for the default
devicetree setting to be retimer disabled on port 0 for Aux Orientation.
Change the default to be Aux Orintation retimer controlled on all ports and
move the SOC controlled overrides to the corresponding overridetree files.
BUG=NONE
BRANCH=NONE
TEST=Built image for delbin and verified that port 0 flip is working.
Change-Id: I5ff59493472db096c027d223f2fd61545dc935e2
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
TBT ports should be disabled if the DB is a USB3 DB. It is assumed if
the DB doesn't support USB4 the platform as a whole should only be USB3
capable and TBT functionality on both ports should not be enabled.
BUG=NONE
BRANCH=NONE
TEST=Built coreboot and verified that TBT was disabled on platform with
USB3 DB and enabled on platform with USB4/TBT DB
Change-Id: I594f2e9483aaf896de2b6aea9a3460bd3826c58c
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add new ddr_memory_cfg structure to support both DDR4 and LPDDR4x
memory types.
Change existing variant code to use the new meminit_ddr() call
instead of calling meminit_lpddr4x() directly.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that
volteer still boots. NOTE that this only tests the lpddr4 side
of the implementation as I do not have a DDR4 board to test this on.
Change-Id: Id4bca2bfa97530f0d04a0e8d90f01b8281d2aea6
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
It is expected TCSS D3Hot is enabled. D3Cold configuration is
through SoC stepping determination. D3Cold is disabled on pre-QS
platform and enabled on QS platform.
BUG=None
TEST=Verified both of TCSS D3Hot and D3Cold configuration on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I9a8b838dcb449ca78d15b18543d97d84b59417ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44004
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7378aa7d6156ece3ab3959707a69f45886f86d21
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set power limits in devicetree for Tiger Lake Y-SKU based volteer
variant boards.
BUG=b:152639350
BRANCH=None
TEST=Built and tested power limits on volteer variant board.
Change-Id: If4f1226473b48365e5962df9fff29910c99007fc
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43607
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While the DPTF refactor was in progress, TSR3 was added to volteer's
dptf.asl file, and I forgot to update the devicetree with TSR3 as well.
Also missed a swap in the passive policies of TSR0 and TSR1. This patch
fixes those.
BUG=b:149722146
TEST=boot volteer, dump SSDT & DSDT, verify TSR3._STA returns 0xF
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I71bc798492ec45bb1e2f8d779e6829db52ef4499
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Enable SataPortsEnableDitoConfig for port 1.
BUG=b:151163106
BRANCH=None
TEST=Build and boot volteer.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I552faaa0e7172e77208025cf4251bb848cc90709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42415
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SaGv needs to be enabled for only QS. On ES2, we are seeing system
instability.
BUG=b:159198381
TEST=Tested for boot. Power and performance tests were run with
volteer2 with qs setup. System showed stability.
Tested for boot stability on on delbin.
Change-Id: I1bce3b9f837fb19ba5a20ae31750a73474a86788
Signed-off-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This patch converts the current DPTF policies from static ASL files into
the new SSDT-based DPTF implementation. All settings are intended to be
copied exactly.
Change-Id: I964c53afbd503d47a07b982672425f0e7a986a3f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41895
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Windows definition
There was a review comment for Chromium Linux ov2740 driver that
Windows driver already set the HID as INT3474 and suggested to have
the same value for Chrome.
The upstreamed Linux driver code has INT3474 as HID and this patch is
to set the same HID in ACPI configuration.
https://patchwork.kernel.org/patch/11540753/
BUG=b:160334865
BRANCH=none
TEST=User-facing camera should work with the driver which set the HID
as INT3474
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I10e98d32899f31d91c1cc7ddfa099af73d8aef37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43006
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer world-facing camera has a privacy LED and it is supposed
to be turned on only when the camera is being used. But the LED
is always on and this is to fix the issue.
RCAM_SNR_PWR_EN (RearCAMera_SeNsoR_PoWeR_ENable) GPIO, which
controls the world-facing camera LED, was not in the power-up
and power-down sequence definitions and this caused the issue.
BUG=b:160341981
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check the world-facing camera LED is only turned on only when
the camera is working.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I564690baffddfdd0f998525992643aaf16ba4b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42985
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable HotPlug for the PCIe root port that the SD express is on so the
OS can re-train the link without needing a reboot if it goes down
unexpectedly at runtime.
BUG=b:156879564
BRANCH=master
TEST=enable HotPlug on Volteer Root Port 7 (SD express) and check in
linux that it is identified as a HotPlug capable root port
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: Ie9d427dd297567f06123119a670b5ed2e1f73701
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42897
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set tcc_offset value to 10 in devicetree for Thermal Control
Circuit (TCC) activation feature.
BUG=None
BRANCH=None
TEST=Built for volteer platform and verified the MSR value
Change-Id: I6438547e09a3ff3a1c01addfcc01383e89f5b435
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This is to enable Intel ME communication interface HECI1 by
devicetree for PAVP with CSE Lite.
BUG=b:159615125
TEST=Build and boot volteer. Run lspci and check pcie device
00:16.0 Communication controller: Intel Corporation Device a0e0
Change-Id: I68eb51c6a0af77982c060767993265764a2bc926
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move the following volteer-specific devices from baseboard's
devicetree.cb into volteer's overridetree.cb file:
- Goodix Touchscreen
- ELAN Touchscreen
- ELAN Touchpad
- SAR0 Proximity Sensor
Adjust the other variant's overridetree.cb files to correspond to
the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959
TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot
volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update fw_config definition in devicetree.cb to match current
definition for volteer.
BUG=b:159157584
TEST=none
Change-Id: I761893818231880d86fd13cfa61319157d06a7d5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42331
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The pass through mode (SW CM) RTD3 is not supported until QS platform.
D3Cold is needed to be disabled along with upstream TBT firmware
signed_TGL_HR_4C_A0_rev6_pre4_SW_CM_PM_support_ENG_VER_perst_check_fix.
This temporary patch will need to be reverted once PM RTD3 support is
validated on QS platform.
BUG=b:159050315
TEST=Verfiy PM S0ix along with upstream TBT firmware.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I98ed991e4185abf1f3168e33b099e0e97c9075f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42504
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Divya Sasidharan <divya.s.sasidharan@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using guidance from Intel, a new set of power limits (PL1, PL2 & PL4)
are available for TGL-U. They are dependent upon the SKU of the CPU
that the mainboard is running on. Volteer is updated here to use these
new limits.
To accomplish this, the SoC chip config's power_limits_config member
was expanded to an array, which can be indexed by POWER_LIMITS_*_CORE
macros. Just before power limits are applied, the correct set of them
is chosen from the array based on System Agent PCI ID. Therefore, a
TGL board should have two sets of power limits available in the
devicetree.
BUG=b:152639350
TEST=On a Volteer SKU4 (4-core), verified the following console output:
CPU PL1 = 15 Watts
CPU PL2 = 60 Watts
CPU PL4 = 105 Watts
Change-Id: I18a66fc3aacbb3ab594b2e3d6e2a4ad84c10d8f0
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
TGL RVP and Volteer use ov8856 camera module from different vendors.
TGL RVP from Foxlink and Volteer from Sunny. ov8856 sensor is identical
for the two modules but VCM and EEPROM are different. Originally,
Volteer ACPI was set to align with Sunny module, GT9679. But it turned
out GT9679 is compatible with Foxlink's DW9768. So Volteer camera ACPI
configuration doesn't need to keep GT9679.
BUG=b:158188369
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check user-facing camera functionalities.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I792608f86a59b16545dfa4edf6508de7a444bb26
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Daniel H Kang <daniel.h.kang@intel.corp-partner.google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Temporary workaround for S0ix issues related to FSP's handling of 0 value.
When IomTypeCPortPadCfg is 0 FSP completely skips any flow related to this
value which seems to be causing issues with s0ix.
This is still being debugged and a final solution will be made when available
BUG=b:159151238
TEST=flash image with workaround to volteer and verify that s0ix
cycles correctly.
Change-Id: Id79dd1c49958389cdb666b3760abd821bc1973a8
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42268
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.corp-partner.google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables the fourth thermal sensor for fan in DPTF for volteer
BRANCH=None
BUG=b:149722146
TEST= On volteer system check
`cat /sys/class/thermal/thermal_zone5/type` for TSR3
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: Ie11496828133aa71f1017f759516e2e5d3dff2d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
For Volteer mainboard, this patch set optimized values for PCH external
VR settings and ext rail voltage/current, to achieve better power
savings in sleep states.
v1p05 and vnn power rails can be used as an alternative source
by-passing vccin_aux during Sx. This by-pass feature, enables us to
shutdown vccin_aux rail which is higher voltage rail compared to v1p05
and vnn. These both rails were disabled by default in FSP. Changes in
this patch are:
1. v1p05 and vnn rails are enabled and enabled supported voltage types
in S0i1, S0i2, S0i3, S3, S4, S5 states. They were disabled by default.
2. Icc Max for v1p05 changed to 500 mA from default 100 mA.
3. vnn rail's voltage is changed to 5 V from default 4.2 V.
BUG=None
BRANCH=None
TEST="Build and boot volteer and check VR settings with Intel ITP-XDP
debugger and verify approx 250 mW power savings in Sx"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib46423872c956af9aaa92902fce552d5447237c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42223
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF_TSR2_SENSOR_ID to 2. Fixes the issue where TSR1 and
TSR2 have the same DPTF_TSR#_SENSOR_ID value causing them to
report the same temperature under /sys/class/thermal
and also swap TSR0 and TSR1 in DTRT to match physical sensor
in volteer schematics
BRANCH=None
BUG=b:149722146
TEST=On volteer system check TSR1 and TSR2 temperatures, should
report different values
`cat /sys/class/thermal/thermal_zone[3,4]/temp`
Also verify other TSRs using `cat /sys/class/thermal/thermal_zone*/temp`
and `ectool tempsinfo all ; ectool temps all`
Signed-off-by: Deepika Punyamurtula <deepika.punyamurtula@intel.com>
Change-Id: Idc5f35e4faf59b0ee726eb32a08eab4654fb342d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42232
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Move the GPIOs that are likely to be volteer-specific (mostly
peripherals) to reside in variants/volteer/gpio.c so that
variants don't have to override too many GPIO settings.
- Modify malefor's gpio.c to adjust for the changes to baseboard's
gpio.c.
- Remove unused GPP_C3 (USB4_SMB_SCL) and GPP_C4 (USB4_SMB_SCA)
settings.
- Remove unused GPP_D9, GPP_D10, GPP_D11, and GPP_D12 settings.
- Remove unused GPP_E8 (SLP_S0IX), COEX, WWAN, and SNDW related
settings for malefor.
- Remove unused GPP_R4 (HDA_RST_L) setting.
BUG=b:157597158
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer SKU4 to kernel.
Change-Id: Ib2f384f539d55a3a8d4a7608336ef22aca3d8c4f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add the current firmware configuration table for the volteer mainboard
and define some actions based on probe results for audio:
- When I2S options are selected disable the SoundWire GPIOs.
- When SoundWire is enabled disable the I2S GPIOs.
- When no audio is enabled disable all the GPIOs.
BUG=b:147462631
TEST=Test that GPIOs are configured as expected based on the current
value of the fw_config field in cbi.
Change-Id: I179f8b6436be83a2b37911777764bd26a0d404b7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41215
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Move all audio devices from baseboard to the volteer variant.
- Add max98373 devices and enable the driver
- Disable everything in FSP and let coreboot configure GPIOs.
BUG=b:147462631
TEST=this change makes all audio devices show up in ACPI, so this
was tested by ensuring that all audio devices are present in ACPI.
Change-Id: Ic654ea52a549053622603aa8c81fb37577d4e011
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This explicitly enables TCSS DMA0 controller and disables
TBT PCIe2 and PCIE3 since they are unused on volteer.
BUG=:b:146624360
TEST=Built and booted on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I05cc9e3964d8037d433fca443be6e8d5b444bbce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41387
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In Tiger Lake we have support for enabling MIPI clocks at runtime in
ACPI. Hence remove setting pch_islclk from devcietree and chip.h.
Also update functions which reference pch_isclk.
BUG=b:148884060
Branch=None
Test=build and boot volteer and verify camera functionality
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I6b3399172c43b4afa4267873ddd8ccf8d417ca16
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41570
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This explicitly enables both of TCSS D3HotEnable and D3ColdEnable
from Volteer devicetree.cb setting.
BUG=:b:146624360
TEST=Built and booted on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I1a168ad87169c0f6633704c55c9293aa25710188
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
BUG=b:156990317
TEST=emerge-volteer coreboot chromeos-bootimage
Boot to kernel and check the ELAN trackpad can wake up unit from suspend.
Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Change-Id: If4bea8a9742f7533be2e51b855cc39ca77d73608
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable DPTF functionality for volteer platform
BRANCH=None
BUG=b:149722146
TEST=Built and tested on volteer system
Change-Id: I385fb409ccd291d97369295ff99f21c9430880f9
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41427
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Historically in coreboot, the PMC's fixed PCI resources were described
by the System Agent (the MMIO resource), and eSPI/LPC (the I/O
resource). This patch moves both of those to a new Intel SoC-specific
function, soc_pmc_read_resources(). On TGL, this new function takes care
of providing the MMIO and I/O resources for the PMC.
BUG=b:156388055
TEST=verified on volteer that the resource allocator is aware of and
does not touch these two resources:
("PCI: 00:1f.2 resource base fe000000 size 10000 align 0 gran 0 limit 0
flags f0000200 index 0
PCI: 00:1f.2 resource base 1800 size 100 align 0 gran 0 limit 18ff
flags c0000100 index 1")
Also verify that the MEM resource is described in the coreboot table:
("BIOS-e820: [mem 0x00000000fe000000-0x00000000fe00ffff] reserved")
Verified the memory range is also untouchable from Linux:
("system 00:00: [mem 0xfe000000-0xffffffff] could not be reserved")
Change-Id: Ia7c6ae849aefaf549fb682416a87320907fb3fe3
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41385
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Link frequency and a format was not correct for volteer proto 2
ov2740 user-facing camera.
The link frequency is calculated in the following way.
(max frame width * max frame height * max fps * data format in bps
/ number of lanes / data rate) + max 35% of overhead
For ov2740, (1920 * 1080 * 60 * 10 / 2 / 2) = 311Mhz.
360Mhz after adding 18% of overhead.
BUG=b:148428976
BRANCH=none
TEST=Build and boot volteer proto 2 board. Start a camera app
and check user-facing camera functionalities.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I3b51826e123dec394c1b4eb9a1c5b64b8b11459e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41157
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Volteer port 0 (MB PORT) does not have a retimer so the port needs
to be configured for the SOC to handle Aux orientation flipping. This
requires 2 changes setting the TcssAuxOri UPD to 1 for port 0 (Bit 0)
and configuring AUXP and AUXN GPIOs to Native Function 6 so SOC can
control the orientation
BUG=b:145220205
BRANCH=NONE
TEST=booted Volteer proto 2 and verified that the AUX channels flip
when the cable is flipped
Change-Id: Ic81adc24d10322cc305bf0fa4c38514468ea0942
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
As per schematics configure headset interrupt as
edge both for ripto and volteer baseboard.
BUG=b:147085988
BRANCH=none
TEST=Build and boot ripto board. Test that jack functionality
is working fine and also confirm with evtest.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I8e1625140ccf55db8cb0fe3c039f1c31c01069b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on Fibocom HW user manual RESET should be deasserted at least 20ms after the power on pin.
The design for the reset pin is open drain connected to a pull up, so it is set to high-Z (configured as GPIO in) after 20ms.
BUG=b:152013143
BRANCH=none
TEST=traced the signals using a scope to verify timing is met.
Signed-off-by: Alex Levin <levinale@chromium.org>
Change-Id: I7c947d1bc4cce1f97383a2f2c254986e182661c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables the keyboard backlight feature in ACPI for volteer.
BUG=b:156326050
TEST=Verified 'KBLT' shows up in the DSDT ACPI table.
Change-Id: Id1b1bb059368b0cc36cb06e6cdb8b989060a1dde
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kernel pinctrl driver changed for Tiger Lake and went to old scheme.
Kernel patch: https://chromium-review.googlesource.com/c/chromiumos/
third_party/kernel/+/2116670
BUG=b:151683980
BRANCH=none
TEST=Build and boot tgl board. In /sys/kernel/debug/pinctrl
verify INTC34C5:00 listing all the pins.
Cq-Depend:chromium:2116670
Change-Id: I9f1d399ff7380125ad5b935f9590a7d9cc442b04
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39801
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:152893285
BRANCH=none
TEST=Build and boot to OS volteer with Intel SATA and reboot
from OS console
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ibed8f8c445bf2ac2290ffb670d8dfb83fc960438
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Moves mipi_camera.asl from mb/google/volteer/acpi/ to
mb/google/volteer/variant/baseboard/include/baseboard/acpi/.
Adds mipi_camera.asl to variant/[volteer|ripto]/include/acpi/.
Adds new VARIANT_HAS_MIPI_CAMERA Kconfig option.
Adds VARIANT_HAS_MIPI_CAMERA for volteer and ripto variants.
BUG=b:154648941, b:154646959
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
Ripto and Volteer to kernel.
Change-Id: I2f28243dfb945857d26f27f07968a15a3eeb7a4f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40578
Reviewed-by: William Wei <wenxu.wei@bitland.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:149588766
TEST=ELAN and Goodix touchscreen works.
Signed-off-by: Alex Levin <levinale@chromium.org>
Change-Id: I1c3e75eb03a8ab434ee58bf36a155f2255612083
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Remove explicit setting of iDisp Link parameters. These settings are
related to configuration for the link between HD-Audio controller and
Display unit for purposes of HDMI/DP Audio playback. During PO,
observed that without setting these params display part was not
binding. With the latest code verified that we dont need to explicitly
set these parameters anymore. HDMI/DP audio playback works fine with
default settings.
BUG=b:151451125
BRANCH:none
TEST= build and boot volteer/ripto and verify HDMI/DP audio playback
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie003d119918d363e2ff9172936b70416fd73c7f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40263
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jairaj Arava <jairaj.arava@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:154279851
TEST=none
Change-Id: Ibb56d97d5180ab199c52119135f7eff265908667
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update device enable/disable based on PCH EDS#576591 vol1 rev1.2
BRANCH=none
BUG=b:154037185
TEST= boot up OS in volteer and check and check lspci
Unsupported IP should be visable from lspci result
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I61a328da1014ab7584c3ec789971a106c7a0a403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40394
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:151166040
TEST= build and boot volteer and check LTR and AER value
from FSP log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ibbf55e6a08ff5e8f358325bb8e9f1487cc982f95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40268
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix GPIO_PCH_WP (GPP_B11) to associate GPP_PCH_WP with community
zero instead of community 1.
BUG=b:152876091
TEST="emerge-volteer coreboot chromeos-bootimage", flash, boot to
and log into Volteer kernel, execute "wp enable" in H1 console,
execute "crossystem" at kernel prompt and verify that "wpsw_cur"
shows as being "1", Execute "wp disable" in H1 console, execute
"crossystem" at kernel prompt and verify "wpsw_cur" is 0.
Change-Id: I082154efd72459ec54999ed7c7bb7420a38f7b6e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Update memory configuration on Tiger Lake platform to enable Early
Command Training. This feature was not supported before FSP v2527.
BUG=b:150357377
BRANCH=None
TEST= Build and boot volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I674c30f4dfc1af6c0c4a460d66684545a190caf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40023
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change reorganizes memory initialization code for LPDDR4x on
TGL to allow sharing of code when adding support for other memory
types. In follow-up changes, support for DDR4 will be added.
1. It adds configuration for memory topology which is currently only
MEMORY_DOWN, however DDR4 requires more topologies to be
supported.
2. spd_info structure is organized to allow mixed topologies as well.
3. DQ/DQS maps are organized to reflect hardware configuration.
TEST=Verified that volteer still boots and memory initialization is
successful.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib625f2ab30a6e1362a310d9abb3f2051f85c3013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This implementation removes all JSL references from the TGL SoC code.
Additionally, mainboard code changes are done to support build.
BUG=b:150217037
TEST=build tglrvp and volteer
Change-Id: I18853aba8b1e6ff7d37c03e8dae2521719c7c727
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to create a working baseline all ports are being set to have
retimers. Setting the TcssAuxOri UPD to 0 in order for the SoC to not
misconfigure the ports. Volteer will need some additional changes after
this is implemented to account for ports that do not have a retimer.
This setting is in the process of being documented in the TGL EDS and we
can update once it is fully understood what this setting is changing on
the SOC side.
BUG=b:145943811
BRANCH=none
TEST=Boot to OS and check Type-C port1 Display on Volteer,
Connecting Type-c display should work regardless of Type-c cable
orientation.
Change-Id: I29eb0513299126ad8d1ee11ded2c771f28ad13f3
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39460
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is required for PD notifications on the cros_ec driver.
BUG=b:150649744
TEST=Boot volteer with this patch and verify that PD notifier events are
being generated.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Change-Id: I2e72320b025a3dfa7412181586cb142a4503eda5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add HID field in max98357a_config and allow mainboards to set it.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I22d2d078a9a4eb6ab330da8439737ff5133086d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39286
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Provide settings for configuring the link between HD-Audio controller
and display unit for purposes of HDMI/DP Audio playback.
BUG=b:144708516, b:148385924
TEST=none
Change-Id: I225faac68729b28be65b4d8f1f83769a874f84ff
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39356
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Optane memory module shows up as 2 NVMe devices in x2 config - NVMe
storage device and NVMe Optane memory. Storage device uses rp9 and
optane memory uses rp11. This patch enables rp11. Please note that
these two share clk related pins.
Configuring pciecontroller3 to be set from 2x2. This will by done by
auto detecting optane memory: enabling HybridStorageMode.
BUG=b:148604250
BRANCH=chromeos
TEST='Build, boot and look for two NVMe devices with lspci on Volteer'
Cq-Depend: chrome-internal:2501837
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: I5430829b496ed275e2e3bda3c0bf21c3d2132628
Reviewed-on: https://chrome-internal-review.googlesource.com/c/chromeos/third_party/coreboot-intel-private/jsl-tgl/+/2424428
Tested-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39420
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable WWAN PCIe to allow WWAN enumerate as USB on Volteer.
BUG=b:146226689
BRANCH=none
TEST=lsusb shows WWAN device
Change-Id: I04e49e3ec989d20ea3469fce06051c475b0ed0c8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=144874778
TEST=Built with Volteer recipe and verified USB functionality
Change-Id: I6cbdbd8a4f65a0fe19e3fb8d7b60b8b849f104e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:147500717
TEST=none
Change-Id: I32fa27b399127dbf8608e0556c77431d2dad652d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- declare the FPMCU interrupt to be level-triggered
- change EC_PCH_WAKE_ODL gpio to native function mode
- corrected spelling of a signal name in a comment
BUG=b:144933687, b:148179954
BRANCH=none
TEST=none
Change-Id: I62da900d0b71139e55b52d06ec09ca25106f73cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi.
BUG=none
BRANCH=none
TEST=Build and boot volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ia8baf1c7b770db23f31383bda46ae8d090468560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Declare variant_early_gpio_table() weak to allow override by variants.
BUG=b:148385924, b:150810535
TEST=none
Change-Id: Ife5e3b75256f71ecd763c4000fd2c7d7c927bb64
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39300
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the common memory code that was being performed in
mainboard has moved into the soc to reduce redundant code.
This change adapts volteer to use Tiger Lake's new common code.
BUG=b:145642089, b:145238504, b:145564831
BRANCH=none
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, boot to kernel, "cat /proc/meminfo" and verify it reports
"MemTotal: 8038196 kB".
Change-Id: I32c9b8a040728d44565806eece6cf60b6b6073b6
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Created a new Google baseboard named volteer from scratch.
BUG=b:142961277
BRANCH=master
TEST="emerge-volteer coreboot" compiles successfully.
Change-Id: I03a13f3df4e819ab9cf63ad69867c807d2a1b651
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|