Age | Commit message (Collapse) | Author |
|
This patch adds explicit initializations for the remaining named display
(power) control GPIOs to the bootblock GPIO init code. These pins are
usually mapped to pins that are already configured to pull-downs on
power-on reset so this wasn't really required, but we have already moved
them around so often that you never know when EEs might one day move
them to a pin with a different power-on reset configuration, so it's
better to be explicit.
In one particular case, GPIO(67) (used by CoachZ rev1+ but not by
anything else for the EN_PP3300_DX_EDP pin) is not actually a pull-down
on boot, even though that is claimed by the datasheet. This is likely
due to the fact that it can serve as the SPI_HOLD pin for the boot flash
QSPI bus, so even though our board's boot flash doesn't really use that
pin, it seems that the boot ROM still configures it as such.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I533baa962d2dfc87cfa510f442ed2e8912e0e5b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
The BACKLIGHT_ENABLE pin on this board unfortunately defaults to a
pull-up on power on, meaning the backlight is immediately enabled. Best
we can do about that is to turn it off again early and wait until it is
actually correct in the panel power sequence to turn it back on.
Some panels want an explicit 80ms delay after training the eDP
connection before the backlight is turned on (this is probably just to
avoid temporary display artifacts, but whatever). We don't want to
busy-wait that extra time, so instead just delegate turning on that GPIO
to the payload (which is also in charge of the backlight PWM already).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Id8dafbdcb40175fbc9205276eee698583b971873
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Currently it's not possible to add multiple graphics driver into
one coreboot image. This patch series will fix this issue by providing
a single API that multiple graphics driver can use.
This is required for platforms that have two graphic cards, but
different graphic drivers, like Intel+Aspeed on server platforms or
Intel+Nvidia on consumer notebooks.
The goal is to remove duplicated fill_fb_framebuffer(), the advertisment
of multiple indepent framebuffers in coreboot tables, and better
runtime/build time graphic configuration options.
Replace set_vbe_mode_info_valid with fb_add_framebuffer_info or
fb_new_framebuffer_info_from_edid.
Change-Id: I95d1d62385a201c68c6c2527c023ad2292a235c5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Coachz rev1 has changed EN_PP3300_DX_EDP from gpio52 to gpio67.
BRANCH=none
BUG=b:174123578
TEST=emerge-strongbad coreboot chromeos-bootimage.
flash coreboot and boot up normally.
Signed-off-by: yuanliding <yuanliding@huaqin.corp-partner.google.com>
Change-Id: I32a721d0d725bf217debe35a5cdc01aa8f5d5daf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
"printk()" needs <console/console.h>.
Change-Id: Iac6b7000bcd8b1335fa3a0ba462a63aed2dc85b8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Enable caching of memory training data for recovery as well as normal
mode because memory training is taking too long in recovery as well.
This required creating a space in the fmap for RECOVERY_MRC_CACHE.
BUG=b:150502246
BRANCH=None
TEST=Run power_state:rec twice on lazor. Ensure that on first boot,
memory training occurs and on second boot, memory training is
skipped.
Change-Id: Id9059a8edd7527b0fe6cdc0447920d5ecbdf296e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46651
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds some Kconfig hints to make it clearer that the
USE_QC_BLOBS option is required for SC7180 boards and guide the user in
the right direction through menuconfig. Also add those little arrows to
the Trogdor board options that are there on most other boards.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I973cae8026a229408a1a1817c4808b0266387ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Currently, trogdor devices have a section RO_DDR_TRAINING that is used
to store memory training data. Changing so that we reuse the same
mrc_cache API as x86 platforms. This requires renaming
RW_DDR_TRAINING to RW_MRC_CACHE and removing RO_DDR_TRAINING in the
fmap table.
BUG=b:150502246
BRANCH=None
TEST=FW_NAME="lazor" emerge-trogdor coreboot chromeos-bootimage
Make sure that first boot after flashing does memory training
and next boot does not.
Boot into recovery two consecutive times and make sure memory
training occurs on both boots.
Change-Id: I16d429119563707123d538738348c7c4985b7b52
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Id913fc4a89ad5eff6b3487354ff8be7661539fe5
Signed-off-by: Manideep Kurumella <mkurumel@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch updates the display power enable GPIO which moved from 30 to
52 for Coachz. Veterans of this project know that there's no point
trying to ask *why* this change was necessary -- the pins move in
mysterious ways and all we can do is watch and wonder. Pin 30 is now
used for a new camera reset GPIO... surely, there must have been some
excellent reason why that pin couldn't just have become pin 52 instead.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I00ad6a6249df66006b4f2b953a0a2449bd478f6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: Ia76323c749a9ba71cc752a91c968aeacc11e0093
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45212
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:162409909
BUG=b:164196066
BRANCH=NONE
TEST=Verify build of strongbad target
Signed-off-by: Bob Moragues <moragues@chromium.org>
Change-Id: If83bd2c8f25fdd3c9625f40121e55c3c922a66fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45276
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Apparently what I thought was lazor-rev2 is actually lazor-rev3 and
nobody is really sure what lazor-rev4 is going to be at this point or
how we proceed from there. What seems to be somewhat agreed upon is that
for now all Lazor revisions use the "old" GPIO mapping and it's not very
clear if that's ever going to change for Lazor, so let's take the
revision restriction out from Lazor for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4939ccfd8464da6e72b5e01a58489b8c80f5b4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Add sc7180 display hardware pipeline programming support
and invoke the display initialization from soc_init.
Changes in V1:
- added display init required check.
- added edid read function using i2c communication.
- added sn65dsi86 bridge driver to init bridge.
- moved display initialization to mainboard file.
Changes in V2:
- moved diplay init sequence to mainboard file
- moved edid read function to bridge driver.
- calculated timing paramters using edid parameters.
- removed command mode config code.
- moved bridge driver to drivers/ti.
- seperated out bridge and soc code with mainboard file as interface.
Changes in V3:
- add GPIO selection at runtime based on boardid.
- add vbif register struct overlay.
Changes in V4:
- update gpio config for lazor board.
Change-Id: I7d5e3f1781c48759553243abeb3d694f76cd008e
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add sn65dsi86 bridge driver to enable the eDP bridge.
Datasheet used : https://www.ti.com/lit/ds/sllseh2b/sllseh2b.pdf
Changes in V1:
- fix the dp lanes using mask
- separate out the refclk and hpd config to init function
Change-Id: I36a68f3241f0ba316c261a73c2f6d30fe6c3ccdc
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Configure GPIO pins as I2S mode for audio speaker.
The audio speaker does not work on Trogdor revision 1, as the
layout was changed.
Developer/Reviewer reference, be aware of this issue:
https://partnerissuetracker.corp.google.com/issues/146533652
Change-Id: Ia4bbfea591a3231640b53e64f0e4e9d43c4437a3
Signed-off-by: vsujithk <vsujithk@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Some Trogdor variants power their USB hub from a PMIC LDO that is
already enabled by QcLib, and some have a discrete LDO that is
controlled by GPIO_84. For the latter, let's make sure we assert that
GPIO on boot.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9d206cd7154ded3bf179e68c2b1421d0a8ee89f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: mturney mturney <mturney@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
We're moving a lot of pins around on Trogdor again. For firmware this
only affects the RAM and SKU strapping ID pins. Since there are quite a
few of the old devices in circulation this time and some people seem to
care about mosys RAM information working, let's actually check the board
revision and support both cases this time.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If7728d8ea4b7f6e7ff6721ade90f975f6efd5ddd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This is no longer used for chromeos.c.
BUG=b:160752610
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9a716a88ff9811fff46abca229be15522733bfef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This pin has been removed from recent revisions (or at least moved to a
pin that's not controlled like a normal GPIO). It has also never been
used on older ones (I think?). The same GPIO is now used as a SKU ID
pin, so make sure we're not incorrectly configuring it as an output
(although sku_id() overrides that later anyway, but it's still
incorrect).
BUG=b:160754995
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I6e0d56e230d0bef172d7b78cc48263e9b6f059de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43471
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a new variant called Pompom that is identical to Lazor
for now. Also reorder variants alphabetically while we're here.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5a0f297413765bce8353d5a781f0f67446de4e7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Diffentiate Lazor and trogdor build configuration
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I3ad413ea6e658e939796bebdff8c1e0dd76417cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42730
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change defines a Kconfig variable MEMLAYOUT_LD_FILE which allows
SoC/mainboard to provide a linker file for the platform. x86 already
provides a default memlayout.ld under src/arch/x86. With this new
Kconfig variable, it is possible for the SoC/mainboard code for x86 to
provide a custom linker file as well.
Makefile.inc is updated for all architectures to use this new Kconfig
variable instead of assuming memlayout.ld files under a certain
path. All non-x86 boards used memlayout.ld under mainboard
directory. However, a lot of these boards were simply including the
memlayout from SoC. So, this change also updates these mainboards and
SoCs to define the Kconfig as required.
BUG=b:155322763
TEST=Verified that abuild with --timeless option results in the same
coreboot.rom image for all boards.
Change-Id: I6a7f96643ed0519c93967ea2c3bcd881a5d6a4d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42292
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We decided to store the FSG on eMMC instead of SPI flash, so we don't
need this region anymore. Getting rid of it allows us to put more space
into CBFS (to store hi-res bitmaps). Also grow VPD by some remaining
amount to keep the FMAP alignment reasonable.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If73450b65718affae71b6ada70ded5c5f45cfb4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
I'm not quite sure what happened when we first added the code for
Trogdor strappings but something clearly seems to be wrong. First of
all, on newer schematics the RAM_ID_1 pin is actually pin 19, not pin
91. It only used to be 91 on rev0. Whether that was an intentional
change or someone just swapped the digits on accident at some point,
we're not quite sure anymore, but it seems to be 19 going forward so
that is what we should be programming. (ram_code wasn't used for
anything on Trogdor rev0 so we don't care about adding
backwards-compatibility for that.)
The sku_id pins are also somewhat out of whack: first of all, a new
SKU_ID_2 pin was added for rev1 that wasn't there on rev0. Second,
SKU_ID_0 is not GPIO_114. In fact, it has never been GPIO_114. I have no
idea how that number got there. Anyway, fix it. (Like with the ram_code,
SKU IDs were also not used for rev0 so we won't make this
backwards-compatible.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ia14ec74ec2f16ce2661f89d0d597a5477297ab69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Change-Id: I8a207e30a73d10fe67c0474ff11324ae99e2cec6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41360
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configuring pull for SD-card detect pin.
Without this SD-card detection is not working as expected
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Change-Id: I77bf355a049224784a160defa6bee66d0f9ceb75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40534
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Configuring GPIO Pins as I2S mode for Audio speaker.
Change-Id: I681aa6d0d57671b0fd9b7bc88de6f2cc202a7af0
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch implements the pin changes needed for Trogdor rev1.
Unfortunately, coreboot has to get the EC and TPM SPI busses compiled
into Kconfig, so we cannot really build a single image that runs on both
revisions. Introduce a Kconfig to handle this instead.
Change-Id: I2e48dc4565682c12089b6cf92c29f4cef4d61bb8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required for TPM IRQ.
Change-Id: I8198213cf2808be5291620892185b1e534263e3f
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38714
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8ff5dd63fac28ffa558aec71e79a6de87d7885e0
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37306
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I64d9468682a4aae3084b17b8724d035f17d01dff
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Used commands:
perl -i -p0e 's|\/\*[\s*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-only */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*]*free[\s*]*software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*either[\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License,[\s*]*or[\s*]*.at[\s*]*your[\s*]*option.[\s*]*any[\s*]*later[\s*]*version.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-or-later */|' $(cat filelist)
perl -i -p0e 's|\/\*[\s*]*.*is[\s*#]*free[\s*#]*software[;:,][\s*#]*you[\s*#]*can[\s*#]*redistribute[\s*#]*it[\s*#]*and/or[\s*#]*modify[\s*#]*it[\s*#]*under[\s*#]*the[\s*#]*terms[\s*#]*of[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*as[\s*#]*published[\s*#]*by[\s*#]*the[\s*#]*Free[\s*#]*Software[\s*#]*Foundation[;:,][\s*#]*either[\s*#]*version[\s*#]*3[\s*#]*of[\s*#]*the[\s*#]*License[;:,][\s*#]*or[\s*#]*.at[\s*#]*your[\s*#]*option.[\s*#]*any[\s*#]*later[\s*#]*version.[\s*#]*This[\s*#]*program[\s*#]*is[\s*#]*distributed[\s*#]*in[\s*#]*the[\s*#]*hope[\s*#]*that[\s*#]*it[\s*#]*will[\s*#]*be[\s*#]*useful[;:,][\s*#]*but[\s*#]*WITHOUT[\s*#]*ANY[\s*#]*WARRANTY[;:,][\s*#]*without[\s*#]*even[\s*#]*the[\s*#]*implied[\s*#]*warranty[\s*#]*of[\s*#]*MERCHANTABILITY[\s*#]*or[\s*#]*FITNESS[\s*#]*FOR[\s*#]*A[\s*#]*PARTICULAR[\s*#]*PURPOSE.[\s*#]*See[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*for[\s*#]*more[\s*#]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-3.0-or-later */|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w]*.*is free software[:;][\#\s]*you[\#\s]*can[\#\s]*redistribute[\#\s]*it[\#\s]*and\/or[\#\s]*modify[\#\s]*it[\s\#]*under[\s \#]*the[\s\#]*terms[\s\#]*of[\s\#]*the[\s\#]*GNU[\s\#]*General[\s\#]*Public[\s\#]*License[\s\#]*as[\s\#]*published[\s\#]*by[\s\#]*the[\s\#]*Free[\s\#]*Software[\s\#]*Foundation[;,][\s\#]*version[\s\#]*2[\s\#]*of[\s\#]*the[\s\#]*License.*[\s\#]*This[\s\#]*program[\s\#]*is[\s\#]*distributed[\s\#]*in[\s\#]*the[\s\#]*hope[\s\#]*that[\s\#]*it[\s\#]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
perl -i -p0e 's|(\#\#*)[\w*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist)
Change-Id: Ia01908544f4b92a2e06ea621eca548e582728280
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41178
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This replaces GPLv2-or-later and GPLv2-only long form text with the
short SPDX identifiers.
Commands used:
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist)
Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
That makes it easier to identify "license only" headers (because they
are now license only)
Script line used for that:
perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist...
Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I4d9bc98863c4f33c19e295b642f48c51921ed984
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37069
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We decided to add a third RAM_CODE pin to the Trogdor family for devices
after rev1. This patch adds support to read it. Since the newly used pin
was previously unconnected (not pulled down) on rev1, this will change
the RAM_CODE result for previous versions (and actually make it
undetermined until we enable tri-state). But since we're not actually
using RAM_CODE for anything yet, and since those are development
revisions that will eventually be discontinued, this should be fine.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9b52982f17646a305b1a3e2c7d37606a7c38d0c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I2ba6f07aa2568c6abf20d6c92ec26bc97f4acdbb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40198
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds GOOGLE_LAZOR which is just a copy of GOOGLE_TROGDOR for
now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0dca8e1c29bdd91625d58b3cb583b530ed925e9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
wpsw_boot is deprecated in favour of wpsw_cur. As such,
coreboot no longer needs to share "write protect" GPIO
with depthcharge.
BUG=b:124141368, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I2fcb7f82aa063fd72928171af5cbef0356ba620c
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:2088434
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39318
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9eedae837634beb5a545d97fdf9c1810faba5138
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37271
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I126d1d6b582ea95c97ac55784d44d3081aabdae7
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch changes all existing instances of clrsetbits_leXX() to the
new endian-independent clrsetbitsXX(), after double-checking that
they're all in SoC-specific code operating on CPU registers and not
actually trying to make an endian conversion.
This patch was created by running
sed -i -e 's/\([cs][le][rt]bits\)_le\([136][624]\)/\1\2/g'
across the codebase and cleaning up formatting a bit.
Change-Id: I7fc3e736e5fe927da8960fdcd2aae607b62b5ff4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Change-Id: Ic92e08ae5b741889a8200d10ea8148e4b4384dc8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37270
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Guckian
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kconfig became stricter on what it accepts, so accomodate before
updating to a new release.
Change-Id: I92a9e9bf0d557a7532ba533cd7776c48f2488f91
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I06cdb8eaaf7f74b47e1d1283dcaa765674ceaa45
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36070
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic2f0944b92dcad7048a0c38720d2ef3c855ef007
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|