| Age | Commit message (Collapse) | Author |
|---|
|
This moves GPIO setup from chip-specific SPI code to mainboard-
specific bootblock code. This makes exynos_spi_open a bit more
generic so it can eventually be used for any SPI channel. This
also benefits CBFS since the user can set media->context to
to any set of SPI registers.
Change-Id: I2bcb9de370df0a79353c14b4d021b471ddebfacd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Note: this patch was originally introduced in 2308, but there were
some ordering issues so it was reverted.
Change-Id: Ibc91c0e26ea8881751fc088754f5c6161d011b68
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use same console initialization procedure for all ARM stages (bootblock,
romstage, and ramstage):
#include <console/console.h>
...
console_init()
...
printk(level, format, ...)
Verified to boot on armv7/snow with console messages in all stages.
Change-Id: Idd689219035e67450ea133838a2ca02f8d74557e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2301
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This reverts commit 9029f4b63f6d0e29bf1608e666cdb025de45ca24
This patch needs to go at the end of the UART patch set. Sorry 'bout the confusion!
Change-Id: I5702c7d6130daf95776f2c15d24e5d253691cefd
Reviewed-on: http://review.coreboot.org/2319
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Change-Id: Ic863e222871a157ba4279a673775b1e18c6eac0d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2308
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The power_init is not required on Exynos 5250 (snow) in bootblock stage. To get
a cleaner and faster bootblock, we can remove it.
Note, power_init internally calls max77686 and s3c24x0_i2c, so both files are
also removed.
Verified to boot on armv7/snow.
Change-Id: I5b15dfe5ac7bf4650565fea0afefc94a228ece29
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The I2C initialization (on component MAX77688) is already done in power_init, so
we should not need an explicit call inside bootblock.
Verified to boot on armv7/snow.
Change-Id: I68c248a8b5fee4ab838b2fb708649e112559cc41
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Remove duplicated / testing code and share more driver for bootblock, romstage
and ramstage.
The __PRE_RAM__ is now also defined in bootblock build stage, since bootblock is
executed before RAM is initialized.
Change-Id: I4f5469b1545631eee1cf9f2f5df93cbe3a58268b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2282
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This attempts to clean out some dead code which was copy + pasted
into Snow's bootblock.c file, along with some unnecessary headers.
Change-Id: If9f157a52395a047c249a2a6385e0e8ddf310e59
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2291
Tested-by: build bot (Jenkins)
|
|
This patch moves ARM core and DRAM timing functions around to simplify
the dependencies for system_clock_init().
The original code was architected such that the system_clock_init()
function called other functions to obtain core and memory timings.
Due to the way memory timing information must be obtained on Snow,
which entails decoding platform-specific board straps, the bottom-
up approach resulted in having the low-level clock init code
implicitly depend on board and vendor-specific info:
main()
->system_clock_init()
-> get_arm_ratios()
-> CPU-specific code
-> clock_get_mem_timings()
-> board_get_revision()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
...then proceed to init clocks
...come back to main()
The new approach gathers all board and vendor-specific info in a
more appropriate location and passes it into system_clock_init():
main()
-> get_arm_ratios()
-> CPU-specific code
-> get_mem_timings()
-> board_get_config()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
-> system_clock_init()
...back to main()
Change-Id: Ie237ebff76fc2d8a4d2f4577a226ac3909e4d4e8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2271
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This gets rid of a bunch of duplicate I2C code in the bootblock.
Change-Id: I51f625a0f738cca4ed2453fbcb78092e4110bc7e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This gets rid of a bunch of copy + pasted GPIO code.
Change-Id: I548b2b5d63642a9da185eb7b34f80cbebf9b124f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This gets rid of a bunch of copy + pasted code from Exynos UART
files.
Change-Id: I9fbb6d79a40a338c9fdecd495544ff207909fd37
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2286
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Snow's AP, EC, PMU, and smarty battery share a bus. Both the AP and
EC can act as a master, so to avoid conflicts an arbitration
mechanism consisting of two GPIOs is used.
By default, the AP "owns" the bus unless it is off (in which case
the EC doesn't monitor the arbitration pins). This means the boot
firmware does not need to worry about these lines. The payload may
if it needs to communicate with the EC, though.
In any case, board-specific bus arbitration logic does not belong
in a low-level driver that is supposed to be generic for an entire
CPU family. If the payload needs to talk to the EC, we'll deal with
it there.
Change-Id: I0774d4592af2b21b6ad668441532c5ceab988404
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2272
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This removes some duplicate code from Snow's mainboard bootblock
by utilizing the bootblock build class.
Change-Id: I153247370a8c5127260082dcdca3ebdc5e104fb8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For ARM platform, the bootblock may need more C source files to initialize
UART / SPI for loading romstage. To preventing making complex and implicit
dependency by using #include inside bootblock.c, we should add a new build class
"bootblock".
Also #ifdef __BOOT_BLOCK__ can be used to detect if the source is being compiled
for boot block.
For x86, the bootblock is limited to fewer assembly files so it's not using this
class. (Some files shared by x86 and arm in top level or lib are also changed
but nothing should be changed in x86 build process.)
Change-Id: Ia81bccc366d2082397d133d9245f7ecb33b8bc8b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2252
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The SPI flash driver for Exynos chipset.
Verified to boot on snow/armv7.
Change-Id: I7eef67a9c57f825d09f13ea44c2b59b54345fa7b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2229
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch does a few things to get us into romstage:
- Add romstage as a stage (a later patch adds it as a binary, which
is probably wrong). The Makefile magic is complex enough that we
let it build the XIP file for now, but we no longer use it.
- Replace findstage with loadstage. Loadstage will find a stage,
load the code to memory, and zero the remaining part of memory.
Now we can link the romstage to go anywhere!
- Eliminate magic offsets from code/ldscripts and centralize Kconfig
variables in src/cpu/samsung/exynos5250/Kconfig.
- Tidy up code and serial output
Change-Id: Iae4d2f9e7f429cb1df15d49daf9a08b88d75d79d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2174
Tested-by: build bot (Jenkins)
|
|
This is the bloated Snow bootblock which includes:
- SPI driver
- UART, including requisite I2C, Maxim PMIC, and clock config code.
- Adjustments for magic offsets (id section, stack pointer address)
This is just a temporary solution until we have romstage loading.
Once that happens, we'll rip out all but the code necessary for
copying SPI ROM content into SRAM.
Change-Id: I2a11e272eb9b6f626b5d9783eabb4a720a1d06be
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
