| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 77fb3632a4a3d3004b3aa4950967be9164d9711d.
Reason for revert: This change inadvertently added a submodule.
Change-Id: I6cc2a3cd9d88986a2599a5ff2e5a066b1396a8c0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32472
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
arcada is designed to operate at max power of 140 Watt. Hence set psys_max to 140W.
BUG=b:124792558
TEST=Build and boot arcada.
Change-Id: I280dfb81b3e25c7619a68db487e2b18867f52fda
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Match SMBIOS type 17 device locator with motherboard silk screen,using
"DIMM-A" and "DIMM-B" instead of "Channel-0-DIMM-0" and
"Chaneel-1-DIMM-0".
TEST=Boot up with sarien platform and run dmidecode to check SMBIOS
type 17 have expected output.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie2125c0381bd24d96f725f68cde93a53da8c94c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the Kconfig option to automatically read the board ID
and populate it into the SMBIOS tables.
BUG=b:123261132
TEST=verify current board id from the OS:
cat /sys/class/dmi/id/board_version
rev1
Change-Id: Id41631bfaa627ca9d5034e2ebe93f8ace2ffdad8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32277
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change VmxEnable UPD values based on Kconfig ENABLE_VMX
and remove it from Devicetree and chip.h
Remove Vmx dependency on Vt-d
Change-Id: I4180c2270038a28befd6ed53c9485905025a15ba
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32117
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on HW change, reserve gpio pins for D3 cold control.
A13,A15 for Card reader
H13 for M.2 SSD
BUG=b:123263562
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib4245be8d77c015e56df7b1d53ef82722c51d656
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Three GPIOs are not being used and this change will save 2-3mW
power during S0iX and this power saving is only for Arcada
BUG=b:129990365
TEST= Measure total platform power during S0iX from Arcada
Change-Id: Ie0208bd6c7affb2e87fd76005b727ea7effdf434
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Set new tcc_offset value to 10 degree C. This configures the Thermal
Control Circuit (TCC) activation value to 90 degree C. It prevents
any abrupt thermal shutdown while running heavy workload. This helps
to take early thermal throttling action when CPU temperature goes
above 90 degree C.
Change-Id: Ica77264782b4a3f3e72e73e1b8cb8b2e464fb033
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a support melfas touch panel with i2c address:0x34.
BUG=b:122019253
TEST=tested with new melfas touch panel and worked
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I27f5c47517d093c819cbbbcdafd85d74145887e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32169
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option is duplicated in depthcharge:
https://crrev.com/c/1545144
BUG=b:124141368, b:124192753, chromium:943150
TEST=make clean && make test-abuild
CQ-DEPEND=CL:1545144
BRANCH=none
Change-Id: I48e20ad21cdcb948a23387d3e5fcf142723b0c82
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Follow thermal table for second tunning.
BUG=b:129509918
TEST=Built and tested on sarien system
Change-Id: I64844b84891dc3ab7abe9378cdca5dcf57b3e433
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:129375810
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in. Also confirm bluetooth itself is
functional.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I79a310a55d94d7d20d1705afc11fe47cbb81abc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow b:129375810 to set bluetooth reset_gpio as ACPI_GPIO_OUTPUT_ACTIVE_LOW
BUG=b:129375810
TEST=Verified BT function on Arcada DVT1 system.
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: I816eb2a76f642a2bb1702f38138bce7916334011
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Touchscreen lost function after boot with stylus
touching the screen
BUG=b:128554235
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: I692fc6f245b7fade67862da4986a83d11a2cd51f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32100
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When in romstage call into the EC init function so it can send a
progress code to the EC before memory training starts.
BUG=b:127875364
TEST=boot with FSP debug and ensure EC does not try to turn off the
system while it is still booting.
Change-Id: I5d99fb16bae250a82b652c530c13977e74c3378b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The TPM driver isn't loaded in other stages but verstage so when we try
to communicate with the TPM it fails. We don't need to communicate with
it anyway since the TPM won't continue to tell us that recovery was
requested, only the first query responds with the recovery request.
BRANCH=none
BUG=b:129150074,b:123360379
TEST=1)boot arcada without recovery and notice that the "tpm transaction
failed" log lines are no longer present. 2) boot into recovery using the
ESC refresh power key combination and verify that the recovery reason
was "recovery button pressed"
Change-Id: I13284483d069ed50b0d16b36d0120d006485f7f4
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Assign the FSP UPDs for HPD and DDC of DDI ports. FSP assumes that all
DDI ports are enabled and hence configures the HPD and CLK for DDI ports.
This patch initializes only the required UPDs to enable display ports.
BUG=b:123907904
TEST=DP devices working correctly.
Change-Id: Ic0c172cd3d087fc8f49b01ab23feffdababf7166
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To support both boards with the same firmware add a SKU for
each variant that is used to include the proper EC firmware
image to match what the EC is expecting.
BUG=b:119490232
TEST=tested by faking the EC response to ensure that the OS
and firmware update tools are able to determine the correct
model based on the value returned by the EC.
Change-Id: Iaa677975e0bccbee5ec8a39821fe1637f08270fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update the Kconfig option for disabling ESPI SMI source
to disable it entirely, not just when ACPI mode is disabled.
For the situations where this is needed (just the sarien
board) it is better to completely stop the EC from sending
any SMI events as no actions are taken.
Change-Id: Id94481bb2f0cfc948f350be45d360bfe40ddf018
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:123342945
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibbe67887227af42b6c040deade7bf5da4ce3227f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We were used to set the same values in the system and board tables.
We'll keep the mainboard values as defaults for the system tables,
so nothing changes unless somebody overrides the system table hooks.
Change-Id: I3c9c95a1307529c3137647a161a698a4c3daa0ae
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Accoriding to 574354, we need to tune each port to pass eye diagram
other than just use recommanded setting as they are base guidence only.
Bug=b:124407280
TEST=Build and boot up on arcada board.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I587695809b368edd33852c4241de097ca31e9d66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31632
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable WLAN SAR power table.
BUG=b:123552641
TEST=Verified WLAN SAR power table forllows VPD setting
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I882b1c7ed0b1142a84eb338142e1c984df45eeba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We want to publish "arcada_ish.bin" as the fw name for Integrated
Sensor Hub (ISH) so the kernel shim loader code can use it to
construct the correct path in /lib/firmware/intel for the firmware
load process.
BUG=b:122722008
TEST=Verify that shim loader CLs use new value when constructing
firmware path
Change-Id: I6299de82566a3bad8521f8158bb047d5c1ff0cf8
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For Chrome OS (or vboot), The PRESERVE flags should be applied on
following sections:
RO_PRESERVE, RO_VPD, RW_PRESERVE, RW_ELOG, RW_NVRAM, RW_SMMSTORE,
RW_VPD, RO_FSG (b:116326638), SI_GBE (chromium:936768),
SI_PDR (chromium:936768)
With the new PRESERVE flag, we don't need RO_PRESERVE and RW_PRESERVE in
the future. But it's still no harm to use it if there are multiple
sections all needing to be preserved.
BUG=chromium:936768
TEST=Builds google/eve and google/kukui inside Chrome OS source tree.
Also boots successfully on eve and kukui devices.
Change-Id: I6664ae3d955001ed14374e2788d400ba5fb9b7f8
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#).
BUG=b:123342945
TEST=Verified BT function on Arcada DVT1 system
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I260a2312d47385da3c7ec215267ff63ada04f2c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable the support for providing a MAC address for a dock to use based on
the VPD values set in the platform.
BUG=b:123925776
TEST=tested on sarien by setting VPD values and observing the string
returned by the AMAC() method:
> vpd -i RO_VPD -s "ethernet_mac0"="AA:AA:AA:AA:AA:AA"
> vpd -i RO_VPD -s "dock_mac"="BB:BB:BB:BB:BB:BB"
1) Test with no policy set, returns "dock_mac"
ACPI Debug: "VPD region RW did not verify"
ACPI Debug: "Found VPD KEY dock_mac = BB:BB:BB:BB:BB:BB"
ACPI Debug: "MAC address returned from VPD: BB:BB:BB:BB:BB:BB"
ACPI Debug: "AMAC = _AUXMAC_#BBBBBBBBBBBB#"
2) Test with policy set to "builtin", returns nothing
> vpd -i RW_VPD -s "dock_passthru"="builtin"
ACPI Debug: "Found VPD KEY dock_passthru = builtin" [AMAC returns Zero]
3) Test with policy set to "ethernet_mac0"
> vpd -i RW_VPD -s "dock_passthru"="ethernet_mac0"
ACPI Debug: "Found VPD KEY dock_passthru = ethernet_mac0"
ACPI Debug: "Found VPD KEY ethernet_mac0 = AA:AA:AA:AA:AA:AA"
ACPI Debug: "MAC address returned from VPD: AA:AA:AA:AA:AA:AA"
ACPI Debug: "AMAC = _AUXMAC_#AAAAAAAAAAAA#"
4) Test with policy set to "dock_mac"
> vpd -i RW_VPD -s "dock_passthru"="dock_mac"
ACPI Debug: "Found VPD KEY dock_passthru = dock_mac"
ACPI Debug: "Found VPD KEY dock_mac = BB:BB:BB:BB:BB:BB"
ACPI Debug: "MAC address returned from VPD: BB:BB:BB:BB:BB:BB"
ACPI Debug: "AMAC = _AUXMAC_#BBBBBBBBBBBB#"
Change-Id: I90474e264cc433c0fd1a4b0dbaf98e5f74180d54
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
In order to prevent keyboard keys pressed at boot from causing issues
in the payload remove the PS2 keyboard driver so it does not get
initialized until it is needed in libpayload.
This was enabled initially because the keyboard controller on this
platform does not come up in translated mode, so unless coreboot
called keyboard_init() the keyboard would never work properly in the
kernel because it would come up as an "AT Raw" device instead of an
"AT Translated" device.
Instead of initializing the keyboard in coreboot a workaround is
added to the payload to put the keyboard into translated mode.
BUG=b:126633269
TEST=boot on sarien while pressing keys and ensure libpayload and/or
the kernel does not have any issues initializing the keyboard.
Change-Id: I765e808f0d2589cf23c0349798a07e2706a2a7a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On Sarien, change pin config of 0x19 (headset mic) and
0x21(headset headphone) to change jack location so that naming does
not use "Front" in the name."Front Headphone" --> "Headphone" so it
matches naming on Arcada.
BUG=b:126334749
TEST= verify with 'evtest' command that jack name is
"HDA Intel PCH Headphone" not "HDA Intel PCH Front Headphone"
Change-Id: I36ccf0c0a3952ab363fe6ee313fac8f0cce4dd61
Signed-off-by: Joyce Toh <joyce.toh@intel.com>
Reviewed-on: https://review.coreboot.org/c/31624
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the _DSM method 5 and 6 for entering and exiting S0ix.
The _DSM method gets injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ia908969decf7cf12f505becb4f4a4a9caa7ed6db
Reviewed-on: https://review.coreboot.org/c/31101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After adjustment on Sarien EVT
Touch Screen CLK (Elan): 389.7 KHz
Touch Screen CLK (Melfas): 377.7 KHz
Touch Pad CLK: 385 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope with sarien.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I53b60354e5a7a0ace8efb677775c0a9f8779061d
Reviewed-on: https://review.coreboot.org/c/31476
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow b:123461432#5 to update GPIO H3(CNVI_EN#) for DVT1.
Update setting GPIO H3 to output and low level.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I6a56df9a7bf75f49133a646312ae5093c2652698
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow thermal table (b:123383634 comment#1) for EVT1 tunning.
BUG=b:123383634
TEST=Built and tested on sarien system
Change-Id: I22908e4bf39aedb8cf31a9060084f6f36bff56ca
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
The Intel SOC can only shadow the top 16MB of SPI into memory so
in order to make it easier to access the NVRAM region with memory
mapped interface move it above the much larger RW_LEGACY region.
I tested to confirm that this region can now be read via MMIO
interface and does not need to use the hwseq SPI controller.
Change-Id: Iafacb01eec07beaf474b6a1f2b36a77117e327da
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Create VR settings configuration as per board design.
BUG=N/A
TEST=Build and boot up into sarien platform.
Change-Id: Ic196fd80e5211bd5146158d4d340b52c850a4e62
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/31404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Update dptf for arcada EVT.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ieed8021b83776fdb6320ff89b57c8d2747667fd5
Reviewed-on: https://review.coreboot.org/c/31331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
According to request of comment 35, setting ELAN as the default.
BUG=b:122019253
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: Iee5e7a21545ca798c0c22f86906acc8e7d81e945
Reviewed-on: https://review.coreboot.org/c/31430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Eanble Elan touch for sarien EVT build
BUG=b:119763054
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I790436338705fc9d68f714245e9b9bb518ddb30a
Reviewed-on: https://review.coreboot.org/c/31413
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Follow Northbay and intermal project to add GPIO H3(CNVI_EN#) for DVT1.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I580a6e094d84a7bada534b14c2b65ecf4b9942b0
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#) for DVT1.
BUG=b:123342945
TEST=Built and tested on sarien system
Change-Id: I0caf97f6a2a8abf2914667350c76300733ead1b8
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
All platforms using this code have NO_CAR_GLOBAL_MIGRATION.
Change-Id: I72effa93e36156ad35b3e45db449d8d0d0cabf06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This change uses cnl_configure_pads to configure GPIOs in ramstage so
that cannonlake SoC code can re-configure the GPIOs after FSP-S is
run. This is just adding a workaround until FSP-S is fixed.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I9973c6c49154f1225f0ac34a3240a0d19f911f18
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Select the appropriate system type for the different variants of
the Sarien board.
This will allow the Arcada variant to use the tablet mode feature
of the Intel Virtual Button driver.
Change-Id: I8a829aab012256ec196c8ec0fa298fd2bc77f2e1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove hard coding for SaGv config in devicetree.cb and apply macro for
SaGv config for CNL variants boards
Change-Id: If007589d5c1368602928b1550ec8788e65f70c05
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
After adjustment on Arcada EVT
TouchScreen: 390 KHz
TouchPad: 389 KHz
H1: 389 KHz
BUG=b:120584026, b:120584561
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia6eb332e7a664b211a5025ad07e0d01bf7f8d5bb
Reviewed-on: https://review.coreboot.org/c/31124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase BIOS region(SI_BIOS) from 16MB to 28MB to make more spaces for
upcoming payloads.
BUG=b:121169122
TEST=Build and boot up fine into OS on sarien and arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I4b03e20a485cb819b468c00e68f1539e92731237
Reviewed-on: https://review.coreboot.org/c/31054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
need it
Hide "Add gigabit ethernet firmware" option for boards that do not
use GbE firmware in GbE section.
The option is now hidden by default and can be reenabled on a
per-board basis by selecting MAINBOARD_USES_IFD_GBE_REGION in the
mainboards Kconfig.
The following boards seem to use this:
mb/roda/rv11
mb/ocp/wedge100s
mb/ocp/monolake
mb/lenovo/x230
mb/lenovo/x220
mb/lenovo/x201
mb/lenovo/x200
mb/lenovo/t530
mb/lenovo/t520
mb/lenovo/t430s
mb/lenovo/t430
mb/lenovo/t420s
mb/lenovo/t420
mb/lenovo/t400
mb/kontron/ktqm77
mb/intel/saddlebrook
mb/intel/kblrvp
mb/intel/dg43gt
mb/intel/dcp847ske
mb/intel/coffeelake_rvp
mb/intel/camelbackmountain_fsp
mb/hp/revolve_810_g1
mb/hp/folio_9470m
mb/hp/compaq_8200_elite_sff
mb/hp/8770w
mb/hp/8470p
mb/hp/8460p
mb/hp/2760p
mb/hp/2570p
mb/google/sarien
mb/facebook/watson
mb/compulab/intense_pc
mb/asus/maximus_iv_gene-z
The boards were identified by looking at devicetree.cb, but this
list is possibly still incomplete.
Change-Id: Ibfb07902ad93fe5ff2bd4f869abcf6579f7b5a79
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set tcc offset value to 5 degree celsius for Sarien system.
BRANCH=None
BUG=b:122636962
TEST=Built and tested on Sarien system
Change-Id: I06fbf6a0810028458bdd28d0d8a4e3b645f279ca
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace B0D4 with TCPU for DPTF thermal sensor. This helps to
maintain consistency between coreboot and UEFI BIOS.
Change-Id: I024068c19160e1c08badef3d304ada14455c045f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31028
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for arcada platform, the slow slew rates
are fast time dived by 2.
BUG=none
BRANCH=none
TEST=none
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia838818a76a7f638b24146f3eb48493a4091c9cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31034
Reviewed-on: https://review.coreboot.org/c/31034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add available thermal sensors information for CPU throttling action.
BRANCH=None
BUG=b:120058043
TEST=Built and tested on Arcada system
Change-Id: I748ca0ce43915c96d71e63fb03fc3d1a02adc56c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After adjustment on Sarien EVT
TouchScreen: 380.7 KHz
TouchPad: 379.3 KHz
H1: 392.2 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I0dd92b054d934b38a17898dc8ce9cc18bda1633f
Reviewed-on: https://review.coreboot.org/c/30949
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Change-Id: If336e9d7016987be151ab30d5c037ead3a998fe0
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change tcc offset from 15 to 3 for sarien.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: I1c5d144e92d1e6e9c81b3e6686805ccf744b7203
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30808
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Accoding to desciption in FSP header, Vref Configuration will be set to
2 if VREF_CA to CH_A and VREF_DQ_B to CH_B.
BUG=N/A
TEST=Build and boot up on Arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I02e16e141b81d766a6060ca08283f432abd96647
Reviewed-on: https://review.coreboot.org/c/30280
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Most boards currently do not use EC firmware from SPI flash in the
IFD, this hides this option by default and shows it only for boards
that need it.
A new config variable MAINBOARD_USES_IFD_EC_REGION is introduced to
enable this option for boards that need it.
The following list of boards requiring this was provided by
Lijian Zhao:
1. intel/cannonlake_rvp
2. intel/coffeelake_rvp
3. intel/icelake_rvp
4. google/sarien
5. google/hatch
Change-Id: I52ab977319d99a23a5e982cc01479fe801e172a7
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
1) Add a Platform Data Region called SI_PDR which is allocated in the flash
descriptor for this platform
2) Add a DIAG_NVRAM region for use by the diagnostic payload for non-volatile
storage.
3) Encapsulate both RW_LEGACY and DIAG_NVRAM in a region called RW_DIAG
so it is clear they are associated.
4) Move the RW_DIAG region to the start of the RW region so that once we can
re-enable a larger BIOS region this sub-region will be in the uncached area
since it is not accessed on a normal boot.
BUG=b:119435206
TEST=tested on Arcada board to ensure expected regions are present
Change-Id: Ieb8bc4cf70d0a931e4944210112cfaf5c543f9f3
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify ELAN touchpad bus i2c clk from 466Khz to 400Khz.
BUG=b:119628524
BRANCH=master
TEST=measure ELAN Touchpad CLK
Change-Id: Ia8433c6ef320cea9a0145db4ba440d67ccd0f41e
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30588
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for sarien platform, the slow slew rates
are fast time dived by 8.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I5d38a1e03af08f106e2422a319b34c3fb54bdf28
Reviewed-on: https://review.coreboot.org/c/30448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Define SATA mode to AHCI mode instead of 0, make devicetree more
readable.
BUG=N/A
Change-Id: I903545d9487c1409f9008407fe5bee6aa4959b98
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable ELAN Touchpad and Disable ALPS Touchpad
BUG=b:119628524
BRANCH=master
TEST=ELAN Touchpad can work normally.
Change-Id: I7839459a70768fa95ba4871b1915d2ea86419bbb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
This reverts commit ad41f5512306d118047d2f7243678ddb32b4b06b.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Elan touchpad and WACOM touchscreen
BUG=b:119924134, b:120103010
BRANCH=master
TEST=Verify touchpad and touchscreen on arcada work with this change.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I3dcdb4eeeb32766e64553d9e69e6b7e2b5ba85aa
Reviewed-on: https://review.coreboot.org/c/30146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
There's no LAN connection on Arcada board, so disable PCH GBE.
BUG=N/A
Change-Id: I07c66df50dbe9fefd95a67b5af9e3f61ce6a18aa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
