| Age | Commit message (Collapse) | Author |
|---|
|
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal Shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device (B0: D20: F2) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Sarien.
Change-Id: Ibc336be0523ff4e65a818474907faf20fc417ff4
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device(B0: D18: F0) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Arcada.
Change-Id: I1915b974b10638b0f6ab97c6fb9b7a58d2cabc59
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase reset delay to 120ms of touchscreen to meet wacom touchscreen
T4 specification and resolve re-bind hid over i2c driver failed after
touchscreen firmware auto update.
BUG=b:132211627
TEST=Stress touchscreen firmware auto update 200 times and not found
re-bind driver failed.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I488660aefdc6df27077efc7fec2f3b99adbaef9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Reviewed-by: Nick Crews <ncrews@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Elan's touchpad requires min 0.3us data hold time.
To fine tune the data hold time of i2c1 to meet
specification of Elan's touchpad.
BUG=None
BRANCH=None
TEST=Verified data hold time of i2c1 is around 320ns
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I0fa9db3b50e74f193261be96bd9e305bb19841e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Crews <ncrews@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
These 4 GPIOs are being disconnected in the next board so use the
board ID to configure these pins as not connected to ensure
they do not cause leakage.
Also remove the ACPI _PTS S5 code that was configuring the GPIOs.
This does mean they will cause small leakage in S5 on existing boards,
but it will not affect the new boards.
BUG=b:132393441
TEST=boot on sarien with fake board ID and ensure that coreboot
configures these pads as expected.
Change-Id: I6ac04b9a635829811a09aeab7cba3bb58cfcff47
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
This patch is not actually disabling HECI1 as it requires a dedicated FSP UPD
for WHL/CML SoC code to set this HECI1 chip config.
Change-Id: Ia88f3315a9dc3365d0acc13ed887e7c596c97c91
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dptf for arcada DVT2.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: I302b7cd4c7e0579acb5482800241b5229cfc49f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
BUG=b:133389422
TEST=check SSD's power off sequence to meet PCIE requirement.
SSD's reset should be cleared before clearing SSD's power EN Pin.
Change-Id: Ia106b805deafb8a442b56bcce91b51135cb32988
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33182
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to we turn off SSD power in S5. CB:32952
Based on M2 spec we have to turn on SSD power
before RST assert.
BUG=b:133389422
TEST=verify warm boot and cold boot are boot
successfully.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5b78bab4be675bbb8795361bcfa5af52cb54bb1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Turn off SSD power in S5.
BUG=b:133389422
TEST=measure H13 is low in S5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I40b5381cac33b0eac962a7730ee5c57e60e6d375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify reset delay to 20ms of touchscreen to address
i2c hid driver rebind failed issue after auto update of
touchscreen firmware
BUG=b:132211627
TEST=Touchscreen works after auto update and no re-bind
driver failed issue
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: If17afbd160a2c97beb69d0cb50e4a7dc654775f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
sarien/arcada:
GPIO_COMM_0/2/3/4: Enable gpio community all PM configuration
GPIO_COMM_1: Disable RCOMP clock gating due to GPP_D18 IRQ mapped for H1 TPM.
hatch:
GPIO_COMM_0/1/2/3: Enable gpio community all PM configuration
GPIO_COMM_4: Disable RCOMP clock gating due to GPP_C21 IRQ mapped for H1 TPM.
BUG=b:130764684
TEST=H1 TPM interrupt working find and able to boot from fixed boot media
Change-Id: Ia4d5483847a4d243b9038119d4bb5990591cc754
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The FSP will lock down the configuration of GPP_A12, which
makes the configuration of the GPIO pin on warm reset not
work correctly.
This is only needed for the Arcada variant since it is the only variant
that uses ISH.
BRANCH=sarien
BUG=b:132719369
TEST=ISH_GP6 now works on warm resets on arcarda
Change-Id: Icb3bae2c48eee053189f1a878f5975c6afe51c71
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32831
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A12 is not current set for ISH_GP6 so the ISH_LID_CL#_TAB
signal is not making it to the ISH properly. Enable the second native
function instead of the first.
BRANCH=none
BUG=b:131785573
TEST=gpioget on ISH now shows the correct gpio level
Change-Id: Ib3a654ae659037263aa9aa29d45b42ca67b7955b
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32738
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Leakage power is observed from TOUCH_SCREEN_PD# (GPP_E7 which is connected
to RESET pin of Wacom controller) during S5.
To avoid leakage power, GPP_E7 needs to be turned off before S5 entry.
BUG=b:129899315
TEST=Measure leakage power in S5 from both Arcada and Sarien
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie4229477b7149c0a75f4a8c6c7c453a37cc1c78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Set tcc offset value to 1 degree celsius for Arcada system.
BRANCH=None
BUG=b:122636962
TEST=Built and tested on Arcada system
Signed-off-by: Bonnie Lin <bonnie_ty_lin@wistron.corp-partner.google.com>
Change-Id: I3ca4be2f7b92e29fb133ecc32023526b177d2ac2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Move optional EC PTS and WAK function into mainboard level.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie91a8168ae234f4fb4843c8587c77ae2f74aeb81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Update dptf for arcada DVT1.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia8024a69547a569d288e02931190a98676eeaab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Fill SMBIOS type 9 fields for both sarien and arcada platform.
BUG=b:129485789
TEST=Boot up into OS and check with dmidecode -t 9 to we do have entry.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I47a697131b7aeeb64e0c4b4c0556842f1cb1b02e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Turn off camera power when s0ix for power saving.
BUG=b:129177593
TEST= measure camera power comsumption is 0mV under s0ix
Change-Id: I5a9b7ec1e95cc9931d8d5f2dc1254805c9d0ffed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
A13 and A15 need to set low before H12 reset. Change
the program sequence for fit HW requirement.
BUG=b:131876963
TEST=boot up and check SD card functional
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2f1752070f24833aaaab75dea8493caf2ed7f157
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I395b2fc527705ab207325cfd7147e6af5f300fce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Chromebook doesn't require support wake on LAN in S5.
Disable it by default for power saving.
BUG=b:131571666
TEST= check LAN indicator is off under S5
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia90c9d2f3ea9b3580e9a7bbfb47c917dd51e3c03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
|
|
This reverts commit 77fb3632a4a3d3004b3aa4950967be9164d9711d.
Reason for revert: This change inadvertently added a submodule.
Change-Id: I6cc2a3cd9d88986a2599a5ff2e5a066b1396a8c0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32472
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
arcada is designed to operate at max power of 140 Watt. Hence set psys_max to 140W.
BUG=b:124792558
TEST=Build and boot arcada.
Change-Id: I280dfb81b3e25c7619a68db487e2b18867f52fda
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change VmxEnable UPD values based on Kconfig ENABLE_VMX
and remove it from Devicetree and chip.h
Remove Vmx dependency on Vt-d
Change-Id: I4180c2270038a28befd6ed53c9485905025a15ba
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32117
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on HW change, reserve gpio pins for D3 cold control.
A13,A15 for Card reader
H13 for M.2 SSD
BUG=b:123263562
TEST=N/A
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib4245be8d77c015e56df7b1d53ef82722c51d656
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Three GPIOs are not being used and this change will save 2-3mW
power during S0iX and this power saving is only for Arcada
BUG=b:129990365
TEST= Measure total platform power during S0iX from Arcada
Change-Id: Ie0208bd6c7affb2e87fd76005b727ea7effdf434
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Set new tcc_offset value to 10 degree C. This configures the Thermal
Control Circuit (TCC) activation value to 90 degree C. It prevents
any abrupt thermal shutdown while running heavy workload. This helps
to take early thermal throttling action when CPU temperature goes
above 90 degree C.
Change-Id: Ica77264782b4a3f3e72e73e1b8cb8b2e464fb033
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a support melfas touch panel with i2c address:0x34.
BUG=b:122019253
TEST=tested with new melfas touch panel and worked
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I27f5c47517d093c819cbbbcdafd85d74145887e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32169
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow thermal table for second tunning.
BUG=b:129509918
TEST=Built and tested on sarien system
Change-Id: I64844b84891dc3ab7abe9378cdca5dcf57b3e433
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:129375810
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in. Also confirm bluetooth itself is
functional.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I79a310a55d94d7d20d1705afc11fe47cbb81abc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow b:129375810 to set bluetooth reset_gpio as ACPI_GPIO_OUTPUT_ACTIVE_LOW
BUG=b:129375810
TEST=Verified BT function on Arcada DVT1 system.
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: I816eb2a76f642a2bb1702f38138bce7916334011
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Touchscreen lost function after boot with stylus
touching the screen
BUG=b:128554235
Signed-off-by: Mike Hsieh <mike_hsieh@wistron.corp-partner.google.com>
Change-Id: I692fc6f245b7fade67862da4986a83d11a2cd51f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32100
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Assign the FSP UPDs for HPD and DDC of DDI ports. FSP assumes that all
DDI ports are enabled and hence configures the HPD and CLK for DDI ports.
This patch initializes only the required UPDs to enable display ports.
BUG=b:123907904
TEST=DP devices working correctly.
Change-Id: Ic0c172cd3d087fc8f49b01ab23feffdababf7166
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To support both boards with the same firmware add a SKU for
each variant that is used to include the proper EC firmware
image to match what the EC is expecting.
BUG=b:119490232
TEST=tested by faking the EC response to ensure that the OS
and firmware update tools are able to determine the correct
model based on the value returned by the EC.
Change-Id: Iaa677975e0bccbee5ec8a39821fe1637f08270fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add bluetooth Rfkill function to recover the Bluetooth controller in
cases where itself has entered a bad state and needs to be recovered.
Bug=b:123342945
TEST=Boot up into OS and dump SSDT table, check there's _DSD entry under
Bluetooth devices with GPIO in.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibbe67887227af42b6c040deade7bf5da4ce3227f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Accoriding to 574354, we need to tune each port to pass eye diagram
other than just use recommanded setting as they are base guidence only.
Bug=b:124407280
TEST=Build and boot up on arcada board.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I587695809b368edd33852c4241de097ca31e9d66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31632
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
We want to publish "arcada_ish.bin" as the fw name for Integrated
Sensor Hub (ISH) so the kernel shim loader code can use it to
construct the correct path in /lib/firmware/intel for the firmware
load process.
BUG=b:122722008
TEST=Verify that shim loader CLs use new value when constructing
firmware path
Change-Id: I6299de82566a3bad8521f8158bb047d5c1ff0cf8
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#).
BUG=b:123342945
TEST=Verified BT function on Arcada DVT1 system
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I260a2312d47385da3c7ec215267ff63ada04f2c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
On Sarien, change pin config of 0x19 (headset mic) and
0x21(headset headphone) to change jack location so that naming does
not use "Front" in the name."Front Headphone" --> "Headphone" so it
matches naming on Arcada.
BUG=b:126334749
TEST= verify with 'evtest' command that jack name is
"HDA Intel PCH Headphone" not "HDA Intel PCH Front Headphone"
Change-Id: I36ccf0c0a3952ab363fe6ee313fac8f0cce4dd61
Signed-off-by: Joyce Toh <joyce.toh@intel.com>
Reviewed-on: https://review.coreboot.org/c/31624
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on Sarien EVT
Touch Screen CLK (Elan): 389.7 KHz
Touch Screen CLK (Melfas): 377.7 KHz
Touch Pad CLK: 385 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope with sarien.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I53b60354e5a7a0ace8efb677775c0a9f8779061d
Reviewed-on: https://review.coreboot.org/c/31476
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow b:123461432#5 to update GPIO H3(CNVI_EN#) for DVT1.
Update setting GPIO H3 to output and low level.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I6a56df9a7bf75f49133a646312ae5093c2652698
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow thermal table (b:123383634 comment#1) for EVT1 tunning.
BUG=b:123383634
TEST=Built and tested on sarien system
Change-Id: I22908e4bf39aedb8cf31a9060084f6f36bff56ca
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create VR settings configuration as per board design.
BUG=N/A
TEST=Build and boot up into sarien platform.
Change-Id: Ic196fd80e5211bd5146158d4d340b52c850a4e62
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/31404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Update dptf for arcada EVT.
BUG=b:123924662
TEST=Built and tested on arcada system
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ieed8021b83776fdb6320ff89b57c8d2747667fd5
Reviewed-on: https://review.coreboot.org/c/31331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Eanble Elan touch for sarien EVT build
BUG=b:119763054
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: I790436338705fc9d68f714245e9b9bb518ddb30a
Reviewed-on: https://review.coreboot.org/c/31413
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Sarien board may have different touchscreen devices that use the
same I2C slave address but have different requirements such as needing
a special driver or ACPI configuration.
In order to support this the devicetree may be configured with multiple
devices at the same address and at boot time the unused devices will be
disabled.
Because there is no GPIO for selecting the device that is present it can
instead be selected with Kconfig, or by setting a VPD key to the HID of
the touchscreen device that is present. The default for Sarien devices
is to not enable a touchscreen for the OS.
The touchscreen selection is currently limited to the Sarien variant but
this also adds the touchscreen HID for Arcada to Kconfig so it would not
complain about the key not being set.
BUG=b:122019253
TEST=This was tested on a Sarien board by adding a second entry to the
devicetree at the same address. Without this change the SSDT is not
loaded by the kernel because of the address conflict. After this change
no touchscreen is enabled by default, but one can be selected with
Kconfig or by setting the 'touchscreen_hid' VPD key.
Change-Id: I4da12b1de0c551bcd89325fe0d8c66c6ffeb7afc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Follow Northbay and intermal project to add GPIO H3(CNVI_EN#) for DVT1.
BUG=b:123461432
TEST=Built and tested on sarien system
Change-Id: I580a6e094d84a7bada534b14c2b65ecf4b9942b0
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Follow b:123342945 to add GPIO H15(BT_RADIO_DIS#) for DVT1.
BUG=b:123342945
TEST=Built and tested on sarien system
Change-Id: I0caf97f6a2a8abf2914667350c76300733ead1b8
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/31330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable ASPM L1.2 support for embedded realtek card reader, after change
the power consumption for SD controller from 5mW to less than 2mW.
BUG=N/A
TEST=Build and boot up on Arcada platform, check the PCI configuration
on pcie root port offset 0x208 is 0x0f, and offset 0x168 on card reader
is also 0x0f.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I08d85ee332ceee8ed85cd816bc3e6c895528fdb0
Reviewed-on: https://review.coreboot.org/c/31145
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove hard coding for SaGv config in devicetree.cb and apply macro for
SaGv config for CNL variants boards
Change-Id: If007589d5c1368602928b1550ec8788e65f70c05
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
After adjustment on Arcada EVT
TouchScreen: 390 KHz
TouchPad: 389 KHz
H1: 389 KHz
BUG=b:120584026, b:120584561
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia6eb332e7a664b211a5025ad07e0d01bf7f8d5bb
Reviewed-on: https://review.coreboot.org/c/31124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Current Melfas touchscreen driver cannot unregister ifself when
connecting without Melfas touchscreen or connecting with other devices.
And Melfas touchscreen FW can use I2C and HID over I2C driver, so
switch to using HID over I2C driver.
BUG=b:122710830
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Change-Id: If04a2904a0f72a6c8363ab2c9865926c71cb5186
Reviewed-on: https://review.coreboot.org/c/31062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Set tcc offset value to 5 degree celsius for Sarien system.
BRANCH=None
BUG=b:122636962
TEST=Built and tested on Sarien system
Change-Id: I06fbf6a0810028458bdd28d0d8a4e3b645f279ca
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Replace B0D4 with TCPU for DPTF thermal sensor. This helps to
maintain consistency between coreboot and UEFI BIOS.
Change-Id: I024068c19160e1c08badef3d304ada14455c045f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31028
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for arcada platform, the slow slew rates
are fast time dived by 2.
BUG=none
BRANCH=none
TEST=none
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: Ia838818a76a7f638b24146f3eb48493a4091c9cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31034
Reviewed-on: https://review.coreboot.org/c/31034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add available thermal sensors information for CPU throttling action.
BRANCH=None
BUG=b:120058043
TEST=Built and tested on Arcada system
Change-Id: I748ca0ce43915c96d71e63fb03fc3d1a02adc56c
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After adjustment on Sarien EVT
TouchScreen: 380.7 KHz
TouchPad: 379.3 KHz
H1: 392.2 KHz
BUG=b:122657195
BRANCH=master
TEST=emerge-sarien coreboot chromeos-bootimage
measure by scope
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I0dd92b054d934b38a17898dc8ce9cc18bda1633f
Reviewed-on: https://review.coreboot.org/c/30949
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change tcc offset from 15 to 3 for sarien.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: I1c5d144e92d1e6e9c81b3e6686805ccf744b7203
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30808
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Modify ELAN touchpad bus i2c clk from 466Khz to 400Khz.
BUG=b:119628524
BRANCH=master
TEST=measure ELAN Touchpad CLK
Change-Id: Ia8433c6ef320cea9a0145db4ba440d67ccd0f41e
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30588
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable acoustic noise mitgation for sarien platform, the slow slew rates
are fast time dived by 8.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I5d38a1e03af08f106e2422a319b34c3fb54bdf28
Reviewed-on: https://review.coreboot.org/c/30448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Define SATA mode to AHCI mode instead of 0, make devicetree more
readable.
BUG=N/A
Change-Id: I903545d9487c1409f9008407fe5bee6aa4959b98
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable ELAN Touchpad and Disable ALPS Touchpad
BUG=b:119628524
BRANCH=master
TEST=ELAN Touchpad can work normally.
Change-Id: I7839459a70768fa95ba4871b1915d2ea86419bbb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Enable Elan touchpad and WACOM touchscreen
BUG=b:119924134, b:120103010
BRANCH=master
TEST=Verify touchpad and touchscreen on arcada work with this change.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I3dcdb4eeeb32766e64553d9e69e6b7e2b5ba85aa
Reviewed-on: https://review.coreboot.org/c/30146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
There's no LAN connection on Arcada board, so disable PCH GBE.
BUG=N/A
Change-Id: I07c66df50dbe9fefd95a67b5af9e3f61ce6a18aa
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
BUG=b:119799550
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Change-Id: I926c988c141628ae2d98206f9eb615d06357a366
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Turn on the ISH in the device tree.
BUG=b:120295222
Change-Id: I0ba08c245d050aebc6eb06055690c422ab9b51c6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30034
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet
the logic output for WWAN_PERST#_R to high.
BUG=120004153
TEST=Boot up Sarien board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Implement HD Audio verb table for RealTek ALC 3204/3254 codec on google
sarien and arcada board.
BUG=b:119058355,119054586
TEST=Confirm audio play back is working on Sarien and Arcada board.
Change-Id: Icedbb510c7668d96c99c657091fc865f03bf7783
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
|
|
Setting sku_id() is not enough to get a value to show up in the SMBIOS
tables, it also needs to be returned as a string for the table creation
to consume. This change defines the smbios_mainboard_sku() function
and returns a string constant of "sku#" as expected.
Change-Id: I03013bab89d53d1eba969c6ffb7e95fcbb315a81
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Trent Begin <tbegin@google.com>
|
|
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
