| Age | Commit message (Collapse) | Author |
|---|
|
The "write protect" GPIO's cached value is never actually
read after entering depthcharge. Ensure the value from
get_write_protect_state() is being transferred accurately,
so that we may read this GPIO value in depthcharge without
resampling.
The cached value of the "recovery" GPIO is read only on certain
boards which have a physical recovery switch. Correct some of
the values sent to boards which presumably never read the
previously incorrect value. Most of these inaccuracies are from
non-inverted values on ACTIVE_LOW GPIOs.
BUG=b:124141368, b:124192753, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: Ic17a98768703d7098480a9233b752fe5b201bd51
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The TPM driver isn't loaded in other stages but verstage so when we try
to communicate with the TPM it fails. We don't need to communicate with
it anyway since the TPM won't continue to tell us that recovery was
requested, only the first query responds with the recovery request.
BRANCH=none
BUG=b:129150074,b:123360379
TEST=1)boot arcada without recovery and notice that the "tpm transaction
failed" log lines are no longer present. 2) boot into recovery using the
ESC refresh power key combination and verify that the recovery reason
was "recovery button pressed"
Change-Id: I13284483d069ed50b0d16b36d0120d006485f7f4
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Under some scenarios the key ladder on the Cr50 can get disabled. If
this state is detected, trigger a reboot of the Cr50 to restore full
TPM functionality.
BUG=b:121463033
BRANCH=none
TEST=Built coreboot on sarien and grunt platforms.
TEST=Ran 'gsctool -a -m disable' and reboot. Verified coreboot sends
VENDOR_CC_IMMEDIATE_RESET command to Cr50 and that the Cr50 resets and
then the platform boots normally.
TEST=Performed Cr50 rollback to 0.0.22 which does not support the
VENDOR_CC_TPM_MODE command, confirmed that platform boots normally and
the coreboot log captures the unsupported command.
Tested-by: Keith Short <keithshort@chromium.org>
Change-Id: I70e012efaf1079d43890e909bc6b5015bef6835a
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
All platforms using this code have NO_CAR_GLOBAL_MIGRATION.
Change-Id: I72effa93e36156ad35b3e45db449d8d0d0cabf06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
By default this board is configured to not power up after an
EC reset. However in the case of a cr50 firmware update that
will reset the EC it will end up powered off. In order to have
it stay powered up configure the board to power up. This will
get reset to the configured default when it boots again.
BUG=b:121380403
TEST=update cr50 firmware and reboot to ensure system boots and
does not end up powered off.
Change-Id: I85beae24b1bc56bb0813f1fd1305218f04b0c1c8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31058
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support the physical recovery GPIO on sarien it needs
to enable the option VBOOT_PHYSICAL_REC_SWITCH and set the GPIO
number in the coreboot table appropriately so that depthcharge can
correctly determine the GPIO number. The same is done for the
write protect GPIO in this table.
Additionally since we are reading a recovery request from H1 it
needs to cache the result since H1 will only return true on the
first request. All subsequent queries to H1 will not indicate
recovery. Add a CAR global here to keep track of the state and
only read it from H1 the first time.
BUG=b:121380403
TEST=test_that DUT firmware_DevMode
Change-Id: Ia816a2e285d3c2c3769b25fc5d20147abbc71421
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31043
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On the Sarien/Arcada platforms, the EC is not trusted to provide
the state of the ESC+REFRESH+PWR recovery combination. On these
platforms the Cr50 latches the state of REFRESH+PWR for use as the
recovery mode key combination.
BUG=b:122715254
BRANCH=none
TEST=Verify recovery mode screen shown after pressing REFRESH+PWR
Change-Id: If336e9d7016987be151ab30d5c037ead3a998fe0
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Sarien is a new board using Intel Whiskey Lake SOC. It also uses
the newly added Wilco EC, enabled in a separate commit.
Sarien is not a true reference board, it is just one variant of
a very similar design. For that reason it is not considered the
baseboard but rather a standalone variant.
Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
