aboutsummaryrefslogtreecommitdiff
path: root/src/mainboard/google/reef/variants/baseboard
AgeCommit message (Collapse)Author
2017-06-05google/reef: Add coralPatrick Georgi
A new variant copied from reef. Allow override of the SKU. Change-Id: Ibe160e75aa23623812f0fb9121d1d8226afc00d8 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/20020 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-05-12mainboard/google/reef: Config needed GPIO for pull-up WALijian Zhao
This change is needed to minimize circuit level stress, by adjusting circuit voltage for proper operation. For mem config GPIO changes: To avoid leakge as those pins have internal 20K pull and 3.3K pull down on mainboard, change internal pull up to none. BUG=b:37998248 TEST=Boot up into OS and enter s0ix. Change-Id: Id82035d8e1fff9fbb8dd3b4125460cdf61a58488 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/19577 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2017-04-13mainboard/google/reef: Configure sdcard card detect (CD) pin GPIO_177Venkateswarlu Vinjamuri
This configures GPIO_177 as native function. This enables OS to boot from sdcard. BUG=b:35648535 TEST=Check OS boot from sdcard. Change-Id: I73901d4a1b39752cbc452f3286d494587dac95d4 Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/18948 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
2017-04-05mainboard/google/reef: increase trackpad data hold timeAaron Durbin
Even though the i2c spec has no minimum data hold time in fast mode the trackpad vendor indicates 300ns is their minimum. However, the topology of the board uses FET isolation to cross voltage domains. Therefore, the default 300ns which should work isn't reflected on the device side of the voltage isolation circuit. Therefore, increase the data hold time to show an observed data hold time of more than 300ns on the device side. BUG=b:36469182 Change-Id: I1b70f2f53c5a29cc7cfd5035a71ca5811b3bcba0 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/19065 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-03-29mainboard/google/reef: turn off DMIC_CLK_B1 in S0ixSathyanarayana Nujella
Wake On Voice stream capture configuration is mono. It is sufficient to keep DMIC_CLK_A1 on in S0ix; so, turning off DMIC_CLK_B1. Power saving should be visible in the boards which has more than one DMIC connected. BUG=None BRANCH=None TEST=WoV and quad channel DMIC capture works Change-Id: Ic46d4c7b30b945eba47a05d78386f48e4a675a03 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/19018 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Tested-by: build bot (Jenkins)
2017-03-19mb/google/reef: Remove CPU throttling effect of the charger sensorSumeet Pawnikar
It's not relevant to throttle CPU based on the charger sensor. So, remove this CPU throttling effect. BUG=b:35908799 BRANCH=master TEST=Built and booted on Electro DUT Change-Id: I267b6e07fa9def2c91ff9f6035f2d9437faf1965 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18852 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
2017-03-16mainboard/google/reef: Increase PL2 Max to 15WTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_DVT_v0.6_20170314.xlsx) 1. Increase PL2 Max to 15W. BUG=b:35583586 BRANCH=reef TEST=build and verify PL2 Max value on electro dut Change-Id: I13167e28267d5827d79a6bde31f077a01f2bd535 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18807 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-03-10mainboard/google/reef: Modify TCPU, TSR2 and TRT tableTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT2_v0.5_20170306.xlsx) 1. Update DPTF TCPU critical trigger point. TCPU critical point: 105 2. Update DPTF TSR2 passive trigger point. TSR2 passive point: 58 3. Change thermal relationship table (TRT) setting. Change CPU Throttle Effect on CPU sample rate to 10secs. Change Charger Effect on Temp Sensor 2 sample rate to 30secs. Change CPU Effect on Temp Sensor 2 sample rate to 60secs. BUG=b:35583586 BRANCH=master TEST=build and boot on electro dut Change-Id: I85564ccdaf327eeaa13bf1f31d9a933609a21582 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18610 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-03-10mainboard/google/reef: Configure SDCARD card detect pinVenkateswarlu Vinjamuri
This configures GPIO_177 as an input pin for SDCARD card detect. This also changes the ownership of the pin from ACPI to GPIO driver. Assign the sdcard card detect pin in devicetree for reef variants. CQ-DEPEND=448173 BUG=chrome-os-partner:63070 TEST=None Change-Id: Ia8aef60bd7d0ea36afb39f76fab051aa46a2ed64 Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/18497 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-25mainboard/google/reef: keep LPSS_UART2_TXD high in suspend stateAaron Durbin
The cr50 part on reef is connected to the SoC's UART lines. However, when the tx signal is low it causes an interrupt to fire on cr50. Therefore, keep the tx signal high in suspend state so that it doesn't cause an interrupt storm on cr50 which prevents cr50 from sleeping. BUG=chrome-os-partner:63283 BRANCH=reef TEST=s0ix no longer causes interrupt storm on cr50. Power consumption normal. Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18491 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-22acpi: Add ACPI_ prefix to IRQ enum and struct namesFurquan Shaikh
This is done to avoid any conflicts with same IRQ enums defined by other drivers. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18444 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-20drivers/i2c: Use I2C HID driver for wacom devicesFurquan Shaikh
Wacom I2C driver does the same thing as I2C HID driver, other than defining macros for Wacom HID. Instead of maintaining two separate drivers providing the same functionality, update all wacom devices to use generic I2C HID driver. BUG=None BRANCH=None TEST=Verified that ACPI nodes for wacom devices are unchanged. Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18401 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-11mainboard/google/reef: Increase PL1 sampling periodSumeet Pawnikar
Performance degradation seen with current PL1 throttling rate as 8 seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1 throttling rate to 15 seconds, fps score improved. BUG=chrome-os-partner:60038 BRANCH=reef TEST=Built and tested on electro system Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/18317 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2017-02-07mainboards/google/reef: Add support for tablet mode switch.Gwendal Grignou
Reef is a convertible add support for sending Tablet mode switch changes from EC to AP. Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06 Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/18277 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-01-31mainboard/google/reef: remove NHLT DMIC 1ch and 2ch configurationSathyanarayana Nujella
Apollolake boards should use DMIC-4ch configuration in Kernel side and use CaptureChannelMap in userspace to distinguish boards with different number of DMIC's. So, NHLT DMIC 1-ch & 2-ch endpoint configuration will not be required and hence removed. BUG=chrome-os-partner:60827 TEST=Verify internal mic capture TEST='arecord -Dhw:0,3 dmic_4ch.wav -f S16_LE -r 48000 -c 4 -d 10' works Change-Id: Ibe81290906c9e379ae49e437648ee9cd6f123ff8 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/18252 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-31mainboard/google/reef: Set edge triggered interrupt for GPIO_22Vaibhav Shankar
EC sets the logic level based on outstanding wake events. When GPIO_22 is configured as a level triggered interrupt, the events are not cleared from the interrupt handler. Hence, we'd just be re-signalling over and over causing an interrupt storm upon lid open. So, GPIO_22 needs to be configured as EDGE_SINGLE instead of LEVEL. BUG=chrome-os-partner:62458 TEST=Lid close/open. check CPU usage using top. It should not show 70% CPU usage. Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Change-Id: I710a690578c6e5b63be34b7fbcb21c703ef56e3a Reviewed-on: https://review.coreboot.org/18267 Tested-by: build bot (Jenkins) Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-29i2c/generic: Allow GPIOs to be put in _CRS and PowerResource in ACPIFurquan Shaikh
Linux kernel expects that power management with ACPI should always be handled using PowerResource. However, some kernel drivers (e.g. ELAN touchscreen) check to see if reset gpio is passed in by the BIOS to decide whether the device loses power in suspend. Thus, until the kernel has a better way for drivers to query if device lost power in suspend, we need to allow passing in of GPIOs via _CRS as well as exporting PowerResource to control power to the device. Update mainboards to export reset GPIO as well as PowerResource for ELAN touchscreen device. BUG=chrome-os-partner:62311,chrome-os-partner:60194 BRANCH=reef TEST=Verified that touchscreen works on power-on as well as after suspend-resume. Change-Id: I3409689cf56bfddd321402ad5dda3fc8762e6bc6 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18238 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-01-29mainboard/google/reef: Set IOSSTATE for trackpad I2C GPIOsVaibhav Shankar
I2C data (GPIO_132) and Clk (GPIO_133) lines are pulled low during standby states S3/S0ix. This causes leakage of power. To reduce the leakage, we have to pull these lines high during S3/S0ix. This is done by programming the IOSSTATE to HIz. Also note that we are using the internal pull ups to keep at SOC at 1.8V and the I2C lines are not floating. BUG=chrome-os-partner:62428,chrome-os-partner:61651 TEST=Enter S3/S0ix. Measure trackpad power. It should be less than 4mW. Also I2c lines should be pulled high in S3/S0ix. Change-Id: I5570ac37ec3cc41f6463dd6b858fdb56a20a1733 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/18251 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-01-22mainboard/google/reef: Increase TSR1 trigger pointTim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT2_v0.4_20170120.xlsx) 1. Update DPTF TSR1 passive trigger point. TSR1 passive point: 46 BUG=chrome-os-partner:60038 BRANCH=master TEST=build and boot on electro dut Change-Id: If35e4cf2dbf7c506534c52a052598f6204d5315a Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/18183 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-21mainboard/google/reef: remove internal pullups on PP1800_S railAaron Durbin
The PP1800_S rail is turned off in S3. However, enabling internal pullups on the pins which are connected to PP1800_S results in leakage into the P1800_S rail. Fix this by disabling the internal pullups on PP1800_S rail pins. BUG=chrome-os-partner:61968 BRANCH=reef TEST=measured leakage on PP1800_S rail. Gone with this patch. Change-Id: I5ae92b31c1a633f59d425f4105b8db1c9c18c808 Signed-off-by: Aaron Duribn <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18189 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-01-19mainboard/google/reef: Ignore Audio DMIC IOSSTATEVaibhav Shankar
Audio DMIC PLL needs to be ON in S0ix to support Wake on Voice. This requires GPIO_79 and GPIO_80 to be configured as IGNORE IOSSTATE. So DMIC CLKs will be ON in S0ix. Change-Id: If91045a8664ce853366b670b9db38d620818fbab Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/18155 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-17mainboard/google/reef: Ignore SPI IOSTANDBYLijian Zhao
SPI controller need to access flash descriptors/SFDP during s0ix exit, so all fast SPI IO can't be put into IOSTANDBY state. For reef, that will be FST_SPI_CLK_FB, GPIO_97, GPIO_99, GPIO_100, GPIO_103 and GPIO_106. BUG=chrome-os-partner:61370 BRANCH=reef TEST=Enter s0ix state in OS, after resume run flashrom to read SPI content. Change-Id: I5c59601ec00e93c03dd72a99a739add0950c6a51 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/18137 Tested-by: build bot (Jenkins) Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-01-03mainboard/google/reef: Update DPTF parameters EVT1_v0.3Tim Chen
Update the DPTF parameters based on thermal test result. (ZHT_DPTF_EVT1_v0.3_20161227.xlsx) 1. Update DPTF CPU/TSR1/TSR2 passive/critial trigger points. CPU critical point:103 TSR1 passive point:45 TSR2 passive point:55, critical point:90 2. Change thermal relationship table (TRT) setting. Change CPU Throttle Effect on CPU sample rate to 3secs Change Charger Effect on Temp Sensor 2 sample rate to 60secs Change CPU Effect on Temp Sensor 1 sample rate to 8secs BUG=chrome-os-partner:60038 BRANCH=master TEST=build and boot on electro dut Change-Id: I3746750f7ea4a2e01153a36c28a5c33140c9e38c Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17975 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-17google/reef: Use exported GPIOs and ACPI regulator for touchscreenFurquan Shaikh
ELAN touchscreen device expects firmware to export GPIOs and ACPI regulators for managing power to the device. Thus, provide the required ACPI elements for OS driver to properly manage this device. BUG=chrome-os-partner:60194 BRANCH=None TEST=Verified that touchscreen works properly on boot-up and after suspend/resume. Change-Id: I298ca5de9c0ae302309d87e3dffb65f9be1e882e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17799 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-12-16drivers/i2c/generic: Allow mainboards to export reset and enable GPIOsFurquan Shaikh
Add power management type config option that allows mainboards to either: 1. Define a power resource that uses the reset and enable gpios to power on and off the device using _ON and _OFF methods, or 2. Export reset and enable GPIOs in _CRS and _DSD so that the OS can directly toggle the GPIOs as required. GPIO type needs to be updated in drivers_i2c_generic_config to use acpi_gpio type so that it can be used for both the above cases. BUG=chrome-os-partner:60194 BRANCH=None TEST=Verified that elan touchscreen works fine on reef using exported GPIOs. Change-Id: I4d76f193f615cfc4520869dedc55505c109042f6 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17797 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-12-13mainboard/google/reef: implement phase enforcement pinAaron Durbin
On upcoming boards an optional pull up is applied on GPIO_10 to indicate if the board should have security features locked down for a shipping system. Provide a weak pull down so that all boards will indicate a logic 0 until the stronger pull up resistor is stuffed. BUG=chrome-os-partner:59951 BRANCH=reef Change-Id: I6f514a69bccd05ca02480f3c30d0ad503a955b1e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17803 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-12-08mainboard/google/reef: Set PL2 override to 15000mWSumeet Pawnikar
This patch sets PL2 override value to 15W in RAPL registers. BUG=chrome-os-partner:60535 TEST=Built, booted on reef and verified PL2 value. Change-Id: I4ff6a5e7b8686d97134846ee80cdac10916d58ef Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17730 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-02mainboard/google/reef: Add all DMIC endpointsSathyanarayana Nujella
Independent of Board DMIC configuration, add all DMIC points i.e. add DMIC-1ch, DMIC-2ch, DMIC-4ch endpoints. This allows flexibility to userspace to open capture devices as needed. This is a temporary fix; once upper layers support choosing particular channels from 4-ch PCM stream, we will limit exposing only DMIC-4ch endpoint. BUG=chrome-os-partner:60444 BRANCH=none TEST=Verify All DMIC blobs are included Change-Id: I9729a3570c0668f3da4e7986291ebad6fe1de47a Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/17660 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-12-01mainboard/google/reef: allow variants to modify nhlt oem revisionAaron Durbin
In order to mirror the full flexibility of the NHLT library that allows a caller to set the OEM revision field in the ACPI header modify the variant callback to override the value. Change-Id: I16e539b350a50e3c163be1439c8637b82e53a759 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17651 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2016-11-29mainboard/google/reef: Set DPTF CPU passive temperature trip point to 95CSumeet Pawnikar
This pach sets the DPTF passive temperature trip point for CPU back to 95 degree celsius from 61 degree celsius as per previous thermal optimizations (https://review.coreboot.org/#/c/16766/). BUG=chrome-os-partner:60038 BRANCH=master TEST=built, booted on Reef and verified the passive trip point funtionality. Change-Id: I83ce69b19a94e4ea8ebedfc06f259579ed6dd5d3 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17598 Tested-by: build bot (Jenkins) Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-28mainboard/google/reef: Set PL1 MAX power limit value to 12WTim Chen
Set PL1 maximum power limit value back to 12W (https://review.coreboot.org/#/c/16596/) from 6W due to Intel's and thermal team's suggestion. BUG=chrome-os-partner:60038 BRANCH=master TEST=build, boot on electro dut and verify by thermal team member Change-Id: I57ae29180962724fde72d522caa542f0f21d5922 Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17574 Tested-by: build bot (Jenkins) Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-20mainboard/google/reef: Update DPTF parameters provided from thermal teamTim Chen
Update the DPTF parameters based on thermal test result. 1. Update DPTF CPU/TSR0/TSR1/TSR2 passive/critial trigger points. CPU passive point:61 TSR0 passive point:120, critial point:125 TSR1 passive point:46, critial point:75 TSR2 passive point:100, critial point:125 2. Update PL1/PL2 Min Power Limit/Max Power Limit Set PL1 min to 3W, and max to 6W Set PL2 min to 8W 3. Change thermal relationship table (TRT) setting. Change CPU Throttle Effect on CPU sample rate to 80secs Change CPU Effect on Temp Sensor 0 sample rate to 120secs The TRT of TCHG is TSR1, but real sensor is TSR2. Change Charger Effect on Temp Sensor 2 sample rate to 120secs Change CPU Effect on Temp Sensor 2 sample rate to 120secs BUG=chrome-os-partner:60038 BRANCH=master TEST=build and boot on electro dut Change-Id: I7a701812cb45f51828a3cbb3343e03817645110e Signed-off-by: Tim Chen <Tim-Chen@quantatw.com> Reviewed-on: https://review.coreboot.org/17466 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-17mainboard/google/reef: disable unused devicesJagadish Krishnamoorthy
The following devices i2c6, i2c7, spi1, spi2, uart3 are not used. BUG=chrome-os-partner:59880 TEST=Boot to OS and lspci command should not list the above disabled devices. Change-Id: I819cdb34709703e6431b49446417ed9d6b3543cd Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com> Reviewed-on: https://review.coreboot.org/17441 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-17mainboard/google/reef: set i2c bus timings by rise/fall timesAaron Durbin
Provide the rise and fall times for the i2c buses and let the library perform the necessary calculations for the i2c controller registers instead of manually tuning the values. BUG=chrome-os-partner:58889,chrome-os-partner:59565 Change-Id: I0c84658471d90309cdbb850e3128ae01780633af Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17397 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2016-11-16mainboard/google/reef: Add proper DMIC endpoints based on DMIC config pinSathyanarayana Nujella
Reef board uses GPIO_17 as DMIC config pin. This pin distinguishes board with Quad DMIC's or Mono DMIC. This patch adds necessary DMIC endpoints to support either of those configurations. CQ-DEPEND=CL:*304339,CL:409774 BUG=chrome-os-partner:56918 BRANCH=none TEST=Verify Mono and Quad Channel DMIC record Change-Id: I5b2825b5f39f8962985a129f8ec65265fb18f0b2 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/17158 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-11-10mainboard/google/reef: Add digitizer device to devicetreeFurquan Shaikh
BUG=chrome-os-partner:56246 BRANCH=None TEST=Verified kernel is able to talk to the device. Even without the digitizer, no issues observed with the kernel. Change-Id: I894a5f4cd8f6a51e641a2c8f7b1f682ab76712ae Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17343 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-11-10mainboard/google/reef: Tune digitizer I2C frequency to 400kHzFurquan Shaikh
This brings the I2C frequency down to 400kHz which is spec for fast I2C. BUG=chrome-os-partner:56246 BRANCH=None TEST=Verified frequency in kernel. Change-Id: Ib83c57eec8644903cb9c4b2ab50c94038eb690c1 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17342 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-07mainboard/google/reef: update DMIC related pins configurationSathyanarayana Nujella
CLK_B1(GPIO_80) and DATA_2(GPIO_83) pins needs to be configured as native mode to use them for DMIC record on other potential DMIC's. DMIC blobs configure the clocks. For stereo & quad channel record, both CLK_A1 and CLK_B1 are enabled. For mono channel record, only CLK_A1 is enabled. BUG=chrome-os-partner:56918 BRANCH=None TEST=During DMIC record, check CLK_B1 and DATA_2 lines Change-Id: I838009b85190de5360d593238e48c9593c1dc43a Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/17199 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-11-04reef: tune trackpad i2c frequency to 400kHzAaron Durbin
This brings the frequency down to 400kHz which is spec for fast i2c. BUG=chrome-os-partner:58889 Change-Id: Ibc5f152e55ed618f18ac6425264f086b1f2d1ffa Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17215 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-11-04reef: tune tpm i2c frequency to 400kHzAaron Durbin
This brings the frequency down to 400kHz which is spec for fast i2c. BUG=chrome-os-partner:58889 Change-Id: I8689a062b5457aa431eaa7fb688a7170dad83fcf Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17214 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-28mainboard/google/reef: allow variants to override NHLT OEM stringsAaron Durbin
In certain cases a board variant may need to override the NHLT OEM strings in the main NHLT table. Therefore, provide that path. BUG=chrome-os-partner:56918 Change-Id: I57cc4fd3665698e41ceebb1949180f86bb60b61f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17167 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
2016-10-28mainboard/google/reef: update comment for DMIC config usageAaron Durbin
Going forward GPIO_17 is used to determine the configuration of the board w.r.t. the number of DMICs on the board. BUG=chrome-os-partner:56918 Change-Id: I03edb880e0649977030c1b87219ebebac631a519 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17163 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-27mainboard/google/reef: drop disabling periodic training for micronAaron Durbin
In anticipation of getting fixed material remove the disabling of periodic training for MT53B512M32D2NP and MT53B256M32D1NP. BUG=chrome-os-partner:59003 Change-Id: Iaadaa979d85cab78dda527db7480420af02fd832 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17130 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-10-27mainboard/google/reef: clarify memory part number detailsAaron Durbin
Explain the reasoning for the part_num strings used in the memory SKU table explaining the necessity of keeping mosys in sync with the strings used. It's possible that actual part numbers could change as the higher speed material gets cheaper, for example. BUG=chrome-os-partner:58966 Change-Id: If895e52791dc56e283261b3438106116b8b2ea05 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/17129 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-10-25mainboard/google/reef: Add PowerResource for ELAN touchscreenFurquan Shaikh
Define reset_gpio and enable_gpio for touchscreen device so that when kernel puts this device into D3, we put the device into reset. PowerResource _ON and _OFF routines are used to put the device into D0 and D3 states. BUG=chrome-os-partner:55988 Change-Id: Ia905f9eb630cd96767b639aec74131dbd7952d0e Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/17083 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-10-18mainboard/google/reef: Configure PERST pin for reef DVTVaibhav Shankar
Configure GPIO 122 as PERST on DVT. This is to assert WiFi PERST during s0ix entry. BUG=chrome-os-partner:55877 TEST=S0ix functional on DVT Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Change-Id: Iab18b2de621a1a9226c78493f6defa15081db875 Reviewed-on: https://review.coreboot.org/17030 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-10-16mainboard/google/reef: Set PL1 override to 12000mWVenkateswarlu Vinjamuri
Reef is using APL SoC SKU's with 6W TDP max. We've done experiments and found the energy calculation is wrong with the current VR solution. Experiments show that SoC TDP max (6W) can be reached when RAPL PL1 is set to 12W. Therefore, we've inserted 12W override after reading the fused value (6W) so that the system can reach the right performance level. BUG=chrome-os-partner:56922 TEST=webGL performance(fps) not impacted before and after S3. Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Change-Id: I21c278e82b82d805f6925f4d9c82187825fd0aa0 Reviewed-on: https://review.coreboot.org/17029 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-10-10google/reef: update timing of sdmode togglingSathyanarayana Nujella
Maxim98357a speaker amp requires BCLK & SFRM to be active and stable before it is unmuted. If there is a BLCK and no SFRM, it results in a pop sound. sdmode_delay property already exists which facilitates this configuration. This patch updates "sdmode_delay" to avoid pop sound. BUG=chrome-os-partner:58356 BRANCH=None TEST=while audio playback via headset, remove headset. Audio will be switched playback to speaker. Observe if pop sound comes from speaker. Change-Id: I7ad68caa88d7b3ff52ac1379fe6564de27d97777 Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-on: https://review.coreboot.org/16933 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-10-07x86/acpi_device: Add support for GPIO output polarityFurquan Shaikh
Instead of hard-coding the polarity of the GPIO to active high/low, accept it as a parameter in devicetree. This polarity can then be used while calling into acpi_dp_add_gpio to determine the active low status correctly. BUG=chrome-os-partner:55988 BRANCH=None TEST=Verified that correct polarity is set for reset-gpio on reef. Change-Id: I4aba4bb8bd61799962deaaa11307c0c5be112919 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/16877 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-10-01mainboard/google/reef: Update DPTF policy temp. values for CPUSumeet Pawnikar
This patch increases the CPU specific passive temp. trip point and critical temp. trip point value for DPTF policy. BUG=chrome-os-partner:57903 TEST=Built, booted on reef and verified this passive and critical temp. trip points with heavy workload. Change-Id: I2a38d01a6539c1bd478f8716c4b543ebcd1f2080 Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/16766 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
2016-09-28google/reef: Mark touchpad and touchscreen as probed devicesDuncan Laurie
Add the 'probed' flag to the touchpad and touchscreen devices so they are probed by the kernel before being loaded, in case they do not exist or are replaced with another vendor. BUG=chrome-os-partner:57686 Change-Id: I0a61964e6874cd99fab0c21fa404a43548fc8ab5 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/16743 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-09-26mainboards/google/reef: use chromeec's ASL lid switch implementationAaron Durbin
Defer to the lid switch implementation provided by the chromeec. BUG=chrome-os-partner:56677 Change-Id: Ida451dc29c8cf55fb88015e48a9e0bca3740f645 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16733 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2016-09-21mainboard/google/reef: Enable cr50 TPM interruptDuncan Laurie
Enable the cr50 TPM and interrupt as GPE0_DW1_28 for use during verstage. The interrupt is left in APIC mode as the GPE is still latched when the GPIO is pulled low. BUG=chrome-os-partner:53336 Change-Id: Ib0247653bdcbaccb645cd16b81d7ec3c38f669af Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/16673 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-09-19Revert "mainboard/google/reef: Enable cr50 TPM interrupt"Duncan Laurie
This reverts commit 24de342438208d9b843e87627f15b9a272285b0f.
2016-09-19mainboard/google/reef: Enable cr50 TPM interruptDuncan Laurie
Enable the cr50 TPM and interrupt as GPE0_DW1_28 for use during verstage. The interrupt is left in APIC mode as the GPE is still latched when the GPIO is pulled low. BUG=chrome-os-partner:53336 Change-Id: I28ade5ee3bf08fa17d8cabf16287319480f03921 Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-19mainboard/google/reef: Configure WLAN as wake sourceVaibhav Shankar
This implements PRW method for WLAN and configures PCIe wake pin to generate SCI. BUG=chrome-os-partner:56483 TEST=Suspend the system into S3 or S0ix. System should resume through wake event from wifi. Change-Id: I9bd078c2de19ebcc652b5d981997d2a5b5f0b1b7 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/16611 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2016-09-15mainboard/reef: add variant support to ASL codeAaron Durbin
There are certain board-specific options for reef variants. The big one is the DPTF settings. Rearrange the ASL files such that dsdt.asl is the main landing area. The ACPI options for Chrome EC are contained in the variant/ec.h header so the actual code #includes can just reside in dstd.asl. Since most of the mainboard specific peripherals are auto generated by the acpigen from devicetree there's no real separate need for mainboard.asl. The one thing not addressed in this CL is the notion of a variant having the Chrome EC or not (along with lid, etc). Future indirection can be provided when needed to address that requirement. BUG=chrome-os-partner:56677 Change-Id: I5c888f5fc64913dcff010c28f87e69ac5449e6b6 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16604 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-14mainboard/google/reef: Configure PERST_0 pinVaibhav Shankar
This configures PERST_0 in devicetree. For boards without PERST_0, the pin should be disabled. For boards with PERST_0 the correct GPIO needs to be assigned. BUG=chrome-os-partner:55877 Change-Id: I705009b480e02b4c9b2070bb4f82cb4d552e9a46 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/16603 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-09-13mainboard/google/reef: add MKBP EC event as SCI event.Gwendal Grignou
Add MKBP as a SCI event: the EC is then able to send events coming from the sensors. BUG=b:27849483 TEST=With EC configure to send MKBP events, check sensor information are retrieved by the kernel. Change-Id: Ib06241bfcdc8567769baff4f3371cc0c6eab3944 Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/16594 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-09-12mainboard/google/reef: Enable lpss s0ixVenkateswarlu Vinjamuri
This setting enables lpss to power gate in S0ix. BUG=chrome-os-partner:53876 Change-Id: I0a0fecb0e2b6e5e2f89ac505dd603f4be1bc161e Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/16558 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-09-12mainboard/google/reef: Disable CLKREQ of unused PCIe root portsVenkateswarlu Vinjamuri
1. Removes PCIe blocker for S0ix. 2. Set the correct PCIe root port for wifi/bt on EVT. 3. Turn off CLKREQs of unused PCIe root ports to power gate the IP. Change-Id: Iefd8869688d3a44b435dab9fc792275cd7f7e091 Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com> Reviewed-on: https://review.coreboot.org/16557 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2016-09-08mainboard/google/reef: move devicetree to baseboardAaron Durbin
Move the current devicetree.cb to be under variants/baseboard. New variants can provide their own devicetree as needed. BUG=chrome-os-partner:56677 Change-Id: Ib109ca4be883884b318264500d14aa8d40e3072a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16510 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-09-06google/reef: Enable 20K pull ups for LPC CLKRUN and LAD0:3 linesShamile Khan
The pull up for CLKRUN is required to resolve keyboard slowness and malfunctioning observed on some reef systems. The CLKRUN signal was probed and found to be floating when the pull up was not enabled. Also Added pull ups for the LPC Multiplexed command, address and data lines LAD0:3 because the LPC Interface specification requires them. BUG=chrome-os-partner:55586 BRANCH=none TEST=When a key is pressed, the character is immediately visible on the screen. Also the interrupt count for i8042 increments immediately in /proc/interrupts. Change-Id: I16df1a0301a3994c926a609f61291761219f9e01 Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/16426 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2016-09-06mainboard/google/reef: drop remaining proto board referencesAaron Durbin
The last vestige of the proto boards is the memory sku id gpios. The internal pullups are still required because there's only pulldown stuffing options available on the reef boards. BUG=chrome-os-partner:56791 Change-Id: I04d541a897ec9aacbf2011293d18242fa32896d2 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16432 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-09-06mainboard/google/reef: add baseboard nhlt configurationAaron Durbin
Move the current NHLT configuration implementation to the baseboard area such that other variants can leverage it or provide their own configuration. BUG=chrome-os-partner:56677 Change-Id: If0d48cacdc793492e1618d0eda02a149e33f0650 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16431 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-06mainboard/google/reef: add baseboard memory configurationAaron Durbin
Move the current memory configuration implementation to the baseboard area such that other variants can leverage it. The swizzle config is exported as a global to allow duplicate swizzles to use the same structure while still allowing different memory SKUs. BUG=chrome-os-partner:56677 Change-Id: I57201118053051c01f0e3f164ab4bbaf650b892b Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16430 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-06mainboard/google/reef: provide cros_gpio variant APIAaron Durbin
Add support for Chrome OS gpio ACPI table information by providing weak implementation from the baseboard. BUG=chrome-os-partner:56677 Change-Id: I517764b78f47fb7b3637482ff9efc053cdd1ac69 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16422 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-06mainboard/google/reef: consolidate gpio related defines to one placeAaron Durbin
Since multiple boards will be living within one directory move all the macros for defining anyting related to GPIOs to the gpio.h header file. That way, when other boards land they can override or use them as is. BUG=chrome-os-partner:56677 Change-Id: I36967e57fc61ef354e0b51d1ff1396ce562fa805 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16421 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-06mainboard/google/reef: declare mainboard_ec_init() in each C fileAaron Durbin
There's no common EC header file in the code base, and I didn't want to use a header file for single declaration. Therefore, just move the declaration to each file that uses that symbol. BUG=chrome-os-partner:56677 Change-Id: Ibaebb0ea6a07029aec02d5185cf05ffb8593b117 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16420 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2016-09-06mainboard/google/reef: add variant API for board_id and gpioAaron Durbin
Provide APIs for the board_id() and gpio table functionality. Default and weak implementations are provided from the baseboard. BUG=chrome-os-partner:56677 Change-Id: I02d8deb7f60f8c4842916a9d35f51d8af74b1da4 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16419 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2016-09-04mainboard/google/reef: provide baseboard and variant conceptsAaron Durbin
To further the ability of multiple variant boards to share code provide a place to land the split up changes. This patch provides the tooling using a new Kconfig value, VARIANT_DIR, as well as the Make plumbing. The directory layout with a single variant, reef (which is also the baseboard), looks like this: variants/baseboard - code variants/baseboard/include/baseboard - headers variants/reef - code variants/reef/include/variant - headers New boards would then add themselves under their board name within the 'variants' directory. No split has been done with providing different logic yet. This is purely a organizational change. BUG=chrome-os-partner:56677 Change-Id: Ib73a3c8a3729546257623171ef6d8fa7a9f16514 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/16418 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-18 19:38:09 +0000