Age | Commit message (Collapse) | Author |
|
Fix VBT SSF setting for panel T8/T10 as Akali/Akali360 panel
has T8 minimum 33.3 ms and T10 minimum of 100 ms.
BUG=b:111530392
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test & measure T8/T10 waveform
Change-Id: I642a1aa0b2d13b33e6113f94e73dfc77834766d4
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This change adds variant rammus derived from baseboard poppy.
The setting is copied from the poppy and will be modified later
BUG=b:111579386
BRANCH=master
TEST=emerge-rammus coreboot
Change-Id: I169c225e28183a7a93f1142a3bf87a60b26ce9ca
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/27547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable DW9807 NVM support by adding required ACPI code
BUG:b:110815821
TEST=On Nautilus board, execute "cat /sys/bus/i2c/devices/i2c-INT3499:00/eeprom"
in the terminal and see if there is any data to be dumped.
Change-Id: Ib83fa1a522402a59566e3f55fa5c1af4490266e4
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Reviewed-on: https://review.coreboot.org/27508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
Nautilus-WiFi board doesn't have external pull-up on USB2_OC2# route,then
abnormal over-current is asserted on USB type-A port.
It causes USB type-A port to be blocked, so we need this internal pull-up.
BUG=b:111578984
BRANCH=poppy
TEST=Verified over-current not triggered abnormally on basic sku board
Change-Id: I159f686cef9c8d254f390d7f1dff8011f43fc066
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable the GEO SAR feature for nocturne. OxM programs wifi_sar VPD key in factory.
coreboot reads the VPD and creates the ACPI table as per the WGDS spec.
BUG=b:65155728
BRANCH=none
TEST= Set the wifi_sar VPD with below command (values are junk for test purpose only,
actual values would be set be OxM)
sudo vpd -f <coreboot.rom> -s wifi_sar=30313233343536373839303132333435363738393030313
24142433435364445463031324142433400364445463031323343444546303132333435
Flash the <coreboot.rom> and boot to kernel. Get ACPI table and WGDS would get created
with VPD values passed in.
Change-Id: I32ad591f15fdb34704c8d98d98646dfa2d8882ff
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/27501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Latest nocturne architecture uses clk src 3 for nvme.
BUG=b:111514174
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify nvme
nocturne devices are able to recognize the nvme controller.
Change-Id: I5b2bf012ba88568cb4b0bb3918a3a2c6770ff4c1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27536
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Atlas has one sensor, create a single endpoint to CIO2. Create power
resource for enabling/disabling camera.
BUG=b:111141128
Branch=None
TEST=Testing on Atlas board
Change-Id: Ide0e923bbc34f869dd0227c0a29977645bc5d58d
Signed-off-by: Ping-Chung Chen <ping-chung.chen@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/27350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
|
|
Add new Pantheon sku-id for loading vbt-pantheon.bin
BUG=b:78663963
BRANCH=firmware-nami-10775.B
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I1ee156372754ac0e77caae5959a9ca9884de95f4
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27432
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FCAM_PWR_EN gpio should be GPP_B4 according to the latest board
schematics.
Change-Id: Id926bd224b3392d8a61b6d8ae0509053afaa5b9e
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Reviewed-on: https://review.coreboot.org/27433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To enable ISH device on atlas board, change "device pci 13.0 off end" to
"device pci 13.0 on end" in file
mainboard/google/poppy/variants/atlas/devicetree.cb. "IshEnable" is
not needed.
Config atlas board specific ISH setting in devicetree.cb.
Dynamically load gpio setting for ISH enabled/disabled cases.
BUG=b:79244403
BRANCH=none
TEST=Verified on Atlas board with ISH rework. ISH log showed on console.
Change-Id: I8269a85cd2ab7917bfc0e7d63d988e0e678d0bf2
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
the FPMCU_INT_L on GPP_C11 is active low but the kernel irq handler is
defined as IRQF_TRIGGER_LOW, so do not invert it twice.
BRANCH=poppy
BUG=b:78613978
TEST=On Nocturne, the 'cros_ec' IRQ count in /proc/interrupts does not
increment wildly.
Change-Id: I56c13c797b133dd22669a2299bcd16ef14eed335
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/27221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I85cd567a923cccd2504f351aae276b5f0d9db4de
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt Delco <delco@google.com>
Reviewed-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Until now, chromeec was doing keyboard initialization for the boards
that have DRIVERS_PS2_KEYBOARD selected. However, coreboot does not
leave the keyboard controller in a default reset state. This could
result in payloads or OS failing to probe the controller as there
could be stale data buffered in the controller during the handoff.
Since the boards using chromeec already perform keyboard
initialization in payload, there is no need to initialize the keyboard
in coreboot too. This change gets rid of DRIVERS_PS2_KEYBOARD
selection from all google mainboards using chromeec.
BUG=b:110024487
TEST=Keyboard works fine after booting to OS even if user hits keys
during BIOS to OS handoff.
Change-Id: I1f49b060eb005c0f2b86f9d68d6758954eeb3cf0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Image Processing Unit and CIO2 device that constitute IPU3.
BUG=None
TEST=Build and boot up into Nocturne platform and check with lspci.
Change-Id: Ic2edf5ec7bde5c55ce1b13cf7b680094a9fffc6a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
To make image sensor working, the intended power sequence need to
applied.
BUG=NONE
TEST=NONE
Change-Id: I4833c0e303174b297c1d193495e08e55d294a717
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/27094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Sensors and CSI2 receiver configuration for Nocturne platform.
IMX355 module has VCM, NVM and is on the second port of receiver.
IMX319 module has NVM and is on the first port of receiver.
Change-Id: I37c877df8062d5c79e25ed27775ab58e977555db
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-on: https://review.coreboot.org/26283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These bits start the acquisition process. They should only be set by the
driver.
BUG=b:74363445
TEST=compile
Change-Id: I9e10f5570ac82124f7f4b5cc7aaad27da0c578be
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use lower case for hex values.
BUG=b:74363445
TEST=compile
Change-Id: I24afea58b1a791fac3c87ad397a696f7f6e0d127
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/27264
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to sona thermal table, PL2 need to check cpu id.
And then set PL2 value.
BUG=b:110867809
TEST=The thermal team verify OK
Change-Id: I5759fb3c685e3d4eef1be054541f950843d19874
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
nayna/NT6CL256T32CM-H1 file change byte 145/146 to be"20" for JEDEC spec
BUG=b:79443146,b:109708239
BRANCH=nami
TEST=emerge-nami coreboot chromeos-bootimage
Test on R69.10825 with mosys
Change-Id: Iadc820111f0aed34e5b46d7e23dff44cb5bb811d
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27275
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit changes the uid and desc fields for the sx9310 entries
in the devicetree to be unique, and correctly identify the position
of the respective sensors.
Change-Id: I501df7d3349fdebc9673c9815f5b1b2458abac6e
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
|
|
We would use GPP_B20 instead of board id to determine nautilus SKU.
BUG=b:80052672
BRANCH=poppy
TEST=Verified the new coreboot could determine SKU correctly
Change-Id: I1978b544eef7a184a3da191306ee32d862fa8c36
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27220
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates TSR sensor info with appropriate names.
Also, updates Charger effect with correct TSR sensor mapping.
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board.
Change-Id: Ia3bbc78f8d823e88a91265e0d55c5ac2a4ea31a9
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/27210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
We found GPP_C3 keeps high when system in S0ix mode. It caused 1.8V
leakage. To fix this problem, add GPP_C3 into config for Pantheon
Synaptics touchscreen.
BUG=b:78436458
BRANCH=None
TEST=Let DUT in S0ix mode and check GPP_C3 is normal.
Change-Id: Idb2dab93178af1dae54265e49522b473b69a35af
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27177
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables xDCI controller on nami.
BUG=b:110443736
BRANCH=None
TEST=None
Change-Id: Ieb63e0d65ac1a142c151a3f93afe306b80a5d99a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/27181
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- add K4E6E304EC-EGCF and K4EBE304EC-EGCF to memory strapping table
BUG=b:110498646
BRANCH=none
TEST=none
Change-Id: Iddacdf1e1d0e2bae0c6168c86e54f5f602cd9d19
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27184
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configures a GPIO pin for enabling/disabling bluetooth on the
next version of the atlas board. The default is for bluetooth to be
enabled at this point.
BUG=b:110614620,b:110613353
BRANCH=none
TEST=none
Change-Id: I4ba940e89b1dc03548b7ab44b8f84dc9a3097acb
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27185
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify DPTF TRT parameters to solve thermal sensor QT2 PSV problem.
BUG=b:109941652
TEST=The thermal team verify OK
Change-Id: Id9d39d8282712a0341fea10f74c0e40bb1ac9d7c
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I7358ee34df873098a86d692cc8a909b0ec5023a8
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/27172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- add K4E6E304EC-EGCF and K4EBE304EC-EGCF to memory strapping table
- add SPD files for K4E6E304EC-EGCF and K4EBE304EC-EGCF
BUG=b:110277021
BRANCH=none
TEST=none
Change-Id: If1322311bd91842d6d32725822d91fd6d9e8077c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When played Left Only Audio and Right Only Audio, we observed that Audio
got swapped. Left Data played on Right Speaker and Viceversa.
This patch fixes the above issue.
BUG=b:73635449
TEST=Play Left only & Right only Audio and cross check Audio.
Change-Id: Ie9c417ad0634a76fc8a4126ee75886603f1b3da0
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27167
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set register speed_shift_enable=0 in devicetree to disable
p-states in coreboot as a temporary workaround for an SoC hang.
BUG=b:79666828
BRANCH=none
TEST="emerge-nocturne depthcharge coreboot chromeos-bootimage",
flash spi image onto nocturne, boot to kernel and verify device
stays alive and responsive for several minutes without locking up.
Change-Id: I71ed4c80c109b28ffa85d48338ce3a62396d272e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is a temporary hack to test camera presence before we have full
camera support implemented. Basically, we can now probe the camera
over i2c to verify that it's connected and the camera LED turns on.
BUG=b:80106316
BRANCH=none
TEST=camera LED comes on and camera can be probed over i2c.
Change-Id: Ibaabf6c6f6a1dabaddd2fc47c820e090ca5984a5
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27128
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the necessary config to enable touchscreen sensor in linux.
BUG=b:110286344,b:110286345
BRANCH=none
TEST=verified touch functionality using eval board
Change-Id: I21efafda3f2ae1dcea19e44f8d66f6dfaac1bb12
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We plan to use i2c-hid compatible trackpads on atlas, so this switches
the trackpad config to i2c-hid.
BUG=b:80662079
BRANCH=none
TEST=used trackpad to verify motion tracking
Change-Id: I2702e61a6aa96250c0c09ea4bd15d0c671eedadc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/27126
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change defines SAR sensor device into devicetree.cb.
Since only LTE sku has SAR sensor, we will use GPP_B20 as a device_present_gpio.
BUG=None
BRANCH=poppy
TEST=Verified SAR sensor device is loaded by driver in Chrome OS
Change-Id: Ib4969e4b82d18b1b1a599de8226c2d7d4bda7915
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27149
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nautilus 2nd SKU has a leakage voltage at GPP_D0 in S5 state. We need to set this to LOW when entering S5 for clear the leakage.
BUG=None
BRANCH=poppy
TEST=Verified the leakage is gone after update coreboot
Change-Id: I054e707b2bc2e63d6f99cd2fd8a57be20615f111
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For supporting new SKU, we need to override GPIO table and device configuration.
The board ID of 2nd SKU of nautilus is started from 9, so we would determine SKU with it.
BUG=b:80052672
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: I7242f23f47010664cc29ea86a126e63c9dd62ccd
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27147
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to schematic, we need to correct USB OC pin configuration.
- OC0 for Type-C Port 1
- OC1 for Type-C Port 0
- OC2 for Type-A Port
- OC3 to NC
BUG=NONE
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ic71baef646926cc6aadcc5dda7cb14f00e8d3687
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/27099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dptf.asl and TCC parameters from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI
Change-Id: Ic0ffc169ad3939cacb46824ed23999c61a23d2c4
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_E2 will be used as a BT reset line, so configure GPP_E2 as an
output and initialize it high (high = out of reset).
BUG=b:80089559
BRANCH=none
TEST=none
Change-Id: If45ef3a592c389a0b80298c59eea849d07d9671e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FCAM_PWR_EN signal is changing to connect to GPP_B4 instead of
GPP_D8 as it needs a 3.3v gpio to provide enough power to also
directly power the camera LED.
BUG=b:79667559,b:78122599
BRANCH=none
TEST=none
Change-Id: Ie875ced45dfa2aa7069851004edde8f77329df34
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/27022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add tablet motion control config to nami devices.
BUG=None
BRANCH=None
TEST=run evtest
make sure tablet switch value is 1 in tablet mode and 0
when not in tablet mode
Change-Id: Ie1480934dc003d9b467883e001ed89f9a3694d10
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26970
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- configure GPP_B7 (PCIE_NVME_CLKREQ_ODL) for NF1
- enable root port 9
- add nvme register settings to devicetree
BUG=b:78122599
BRANCH=chromeos-2016.05
TEST='emerge-nocturne depthcharge coreboot chromeos-bootimage',
boot to kernel, and verify /dev/nvme* entries exist.
CQ-DEPEND=CL:1090070
Change-Id: I0070d33b1ed09bd1f51a680d92ddb7e2bcb1ebc2
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
TPM over SPI/I2C config selection got changed in
https://review.coreboot.org/c/coreboot/+/24903 so this CL is fixing the
same.
BUG=None
BRANCH=None
TEST=Build for Soraka & make sure that TPM is probed over I2C interface
rather than SPI.
Change-Id: I077e4dc03520e26eb9f6404a7eb1edd99925de77
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26890
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Sona.
We need to disable rear camera/DMIC on all Sona sku.
BUG=b:109710674
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Sona
Change-Id: Id84ee22c9ffc15db78be3bbad148af5cd7dc866e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since there are two cameras on Nami and only one camera on Pantheon.
We need to disable rear camera/DMIC on all Pantheon sku.
BUG=b:109720689
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Pantheon
Change-Id: Ibe48a945dc57f2c05344479253040ad1945d92fd
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Issue observed on the board is: too many jack interrupts.
cat /proc/interrupts | grep da7219
58: 84292 15709 0 0 IO-APIC 58-fasteoi da7219-aad
Updated pad configuration for Jack IRQ pin to fix the issue.
BUG=b:109655907
TEST=Jack insertion & removal detection is working.
Change-Id: I41ef9d40325677b01ca94ec3215e7feded76dcc3
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
During measurement of signals during Elan touchscreen power on, saw
that the enable_gpio delay was not sufficient as there is a +1.5 ms
delay during power on. Adding more delay to take this into account.
BUG=b:78311818
BRANCH=None
TEST=probe power on signals to ensure meet timing requirements
Change-Id: Id661a202188a97aef97514ebecd0be6fc022d21e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Power off does not seem to use the ACPI _OFF function, but rather the
smihandler. Creating variant_smi_sleep function for nami to handle
the power off sequence during reboot/power off.
BUG=b:78311818
BRANCH=None
TEST=Run "poweroff" command from AP console with SMI_DEBUG enabled
Make sure delays are consistent with spec
Change-Id: Ifeea545fe268be249793b3e508c51f5e4c1a3460
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since Vayne added one more skuid 3A67, we need to disable rear
camera/DMIC for vayne skuid 3A67.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera/DMIC shown on Vayne
Change-Id: I9131b4c41bf189829be4e7e6bfaf4a96765cfa15
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26855
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Remove 2nd software stack in pc80 drivers directory.
* Create TSPI interface for common usage.
* Refactor TSS / TIS code base.
* Add vendor tss (Cr50) directory.
* Change kconfig options for TPM to TPM1.
* Add user / board configuration with:
* MAINBOARD_HAS_*_TPM # * BUS driver
* MAINBOARD_HAS_TPM1 or MAINBOARD_HAS_TPM2
* Add kconfig TPM user selection (e.g. pluggable TPMs)
* Fix existing headers and function calls.
* Fix vboot for interface usage and antirollback mode.
Change-Id: I7ec277e82a3c20c62a0548a1a2b013e6ce8f5b3f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Load vbt-vayne.bin by reading sku-id.
BUG=b:80509366
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: Ia26ea4a9b7679aeb9d98f19ffaa1b686af828339
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The driver only supports streaming images flipped horizontally
and vertically. In order to ensure that all current users will
be fine if or when support for upright streaming is added,
require the presence of the "rotation" control now.
BUG=None
BRANCH=None
TEST=Verified the MIPI and USB camera function on DUT board
Change-Id: I7e3abdea9071da1a089c7165f6bb609428090792
Signed-off-by: Lai, Jim <jim.lai@intel.com>
Reviewed-on: https://review.coreboot.org/26727
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FPMCU is using the standard cros-ec-spi interface on GSPI1.
Configure the GPIOs controlling the MCU too.
We need to be able to wake from S3 on the MCU interrupt, re-configure
GPE0 DW0 to point to GPP_C bank.
BRANCH=poppy
BUG=b:79666174
TEST=exercise the cros_ec interface, e.g. 'ectool --name=cros_fp version',
verify the MKBP events by doing 'ectool --name=cros_fp fpmode fingerup'
then 'ectool --name=cros_fp waitevent 5 10000', toggle the other GPIOs
with the flash_fp_mcu script.
Change-Id: Ib417dcf84cda8e354060785cd16a7b6b812148d5
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/26684
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves PL2 override to variant_devtree_update for two reasons:
1. This function was added to basically override devtree settings in
variant specific code. So, it would be a good idea to perform all the
overrides in a single place.
2. Adding a device for performing nami_enable would require changes to
devicetree and special handling for calling this device enable. Thus,
nami_enable was never getting called.
BUG=b:80148703
Change-Id: Ifa24a7b6e99cad2368b3d656a757f26297373121
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The BT W_DISABLE2# pin is connected to GPP_E4 in the latest schematic.
Update GPP_E4 as GPO and set 1 as default.
BUG=b:79993692, b:72007632
BRANCH=None
TEST=Enable/disable BT/WLAN by following command.
Enable:
localhost ~ # iotools mmio_write32 0xfdae0590 0x40000201
localhost ~ # iotools mmio_write32 0xfdae05a0 0x40000201
Disable:
localhost ~ # iotools mmio_write32 0xfdae0590 0x40000200
localhost ~ # iotools mmio_write32 0xfdae05a0 0x40000200
Change-Id: I9ef1a5314652ab29172d246abd58ee4e1a8a6299
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26502
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables SAR config on Nami with CHROMEOS option.
BUG=b:75077304
BRANCH=master
Change-Id: I8217333db2db6c0fd5e1c144dedd3692b1e1e6a3
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:79617938
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage", flash nocturne,
boot to kernel, run evtest and verify that cros-ec-buttons is present
and functional.
Change-Id: Id710782e1f4e18eaac2a90c7c0f91af5223dbce3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable I2C #5 for rear camera and SAR.
BUG=b:79784124
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' and verify i2c bus #5
is detected.
Change-Id: Ic5b754fb97231aeab0278d71f8ced9343c30feda
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Drive SPKR_RST_L (GPP_A19) high at boot to take audio amps out of
reset.
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage", boot to kernel,
and verify sound works via "aplay /dev/random"
Change-Id: Ia49931f2dc7802edc8a46114b081e4a96eeee604
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- add ACPI register information for touchscreen WCOM digitizer
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify
touchscreen on Nocturne board works.
Change-Id: I9790a930e8ed2748d568ce58c931ce34b3e22007
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The I2C CLKs of SoC should be 400kHz, but waveform show 460kHz to
470kHz. Add I2C parameters to adjust I2C CLKs which 5% lower than
400kHz.
BUG=b:78819970
TEST=The I2C CLKs are 5% lower than 400kHz.
Change-Id: I2c3012b5b59c089801cda8fd7b0c433aad9df36d
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26282
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:78122599
BRANCH=none
TEST="emerge-nocturne coreboot chromeos-bootimage" and verify pogo
pin port is working.
Change-Id: Ide7359366821f33c4746284e65cacdf4e240931d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/26315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update dptf.asl from tuning of the thermal team.
BUG=b:72974136
TEST=Match the result from DPTF UI.
Change-Id: I21ddc337359c3e11ad9756e61ba174b33dfc3c75
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Since there are two ALS device nodes on Nami, need to remove one.
BUG=b:79227879
BRANCH=master
TEST=Verify if only one ALS node is found in /sys/bus/iio/devices
Change-Id: I850af06bec833739afa0c8c516d351d81952ce2c
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26271
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load pantheon.bin by reading sku-id.
BUG=b:78663963
TEST=Boots to OS and display comes up.
Check the board specific vbt binary loaded.
Change-Id: I66cb43d87363b3e8b1a1498cdae8eeeb8b75219d
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:74595040
BRANCH=master
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. Booted on Pantheon with S7817 PCBa connected
3. Check touchscreen device is enabled by evtest
/dev/input/event4: SYTS7817:00 06CB:7817
Change-Id: Ic11684d5ed961af5eb704909f7d06eb0898068c2
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds board-specific implementation of
mainboard_vbt_filename which returns "vbt.bin" by default. This is in
preparation to allow multiple vbt binaries to be added to single
image. More sku_id specific names will be added in follow-up CLs.
BUG=b:79396300
Change-Id: I3821d55bfbe9e5773bd2eb0b0003045a80158d8c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This adds a new SPD entry for samsung's new 4GB memory and updates
atlas to use it instead of the previous gen memory.
BUG=b:79444337
TEST=booted on atlas
Change-Id: I19567736c45a1321586378c3d964c2cbebe24755
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/26185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
hynix/H9CCNNNCLGALAR-NUD
nayna/NT6CL256T32CM-H1
BUG=b:79443146
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I3a362080b9e60adecbac14d5cfe193da44bf87c8
Signed-off-by: T.H. Lin <t.h_lin@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch updates the below:
1)
Nocturne board has only Max98373 speaker amp.
Update both NHLT and DT entries to include only Max98373
and not include DA7219.
2) I2S2 is used for Boot Beep.
So, update GPP_F0 ~ F2 pins accordingly.
3) Include DMIC-4ch configuration.
BUG=b:79362472
TEST=None [Waiting for HW to verify]
Change-Id: I0e9b3a564c22de6e84e96e5e937a3aca4ae73d75
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change:
1. Allows mainboard to add OEM table to CBFS
2. Provides mainboard specific smbios_mainboard_manufacturer that reads
OEM ID from EC using CBI and compares it against the OEM ID in CBFS
table to identify the right OEM string.
BUG=b:74617340
Change-Id: Iff54b12745de3efa7be0801c9a3a9f2a57767dde
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/26142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I8e549e4222ae2ed6b9c46f81c5b5253e8b227ee8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
From coreboot side, include DMIC 4ch NHLT configuration and its
DMIC blob. In OS side, cras picks the needed channels using UCM's
channel map configuration.
So, this patch updates to include DMIC 4ch config.
BUG=b:79158926
TEST=Verified 4-ch record with arecord
TEST=Also verified internal mic record with cras using
'cras_test_client --capture_file dmic.raw --rate 48000
--num_channels 2 --duration 10'
Change-Id: Ic6df00c2f26ad9cdf54152ab021c2b10499c429c
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26019
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This gpio should be active low, but is not currently configured that way.
Changing gpio configuration to reflect that.
BUG=b:73121017, b:77941823
BRANCH=None
TEST=iotools mmio_read32 0xfdae0588 (GPP_E1) Make sure that when pen
is ejected, gpio is low and when pen is inserted, gpio is high.
Also tested that wake upon pen eject is working.
Change-Id: Ic49eea6412c3378dca39a3338b43df12bc27037d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/26017
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's very confusing trying to find the google platform names, because
they seem all unsorted in Kconfig. They're actually sorted according
to the variant name, but previously, that was impossible to tell.
- Add a comment to the top of variants in Kconfig.name
- Inset each variant name. If you start a prompt with whitespace,
it gets ignored, so after trying various ways to indent, the arrow
was the option I thought looked the best.
It now looks like this:
*** Beltino ***
-> Mccloud (Acer Chromebox CXI)
-> Monroe (LG Chromebase 22CV241 & 22CB25S)
-> Panther (ASUS Chromebox CN60)
-> Tricky (Dell Chromebox 3010)
-> Zako (HP Chromebox G1)
Butterfly (HP Pavilion Chromebook 14)
Chell (HP Chromebook 13 G1)
Cheza
*** Cyan ***
Change-Id: I35cb16b040651cd1bd0c4aef98494368ef5ca512
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Currently, we've set TOUCHSCREEN_DIS gpio to disabled. Enabling
through ACPI. Set reset/enable/stop_off_ms variables to get timings
of power off sequence correct.
BUG=b:78311818
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: Ib1543f41f24cbe8c33aeb02e6aa43fd3dd977ed4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a new variant of poppy for the nocturne board.
Key differences from baseboard include:
- GPIO changes
- devicetree.cb changes
- memory stuffing option changes
BUG=b:78122599
BRANCH=none
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Change-Id: I11c7829041b3c45407c17f71b08cc7fc17f717e8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/25803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:74595037
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. check touchpad function
3. evtest
/dev/input/event5: PNP0C50:00 06CB:CD84
Change-Id: I47cb1b13881f0d52860f0afe4bbca7483409de54
Signed-off-by: ivy_jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25913
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configures GPP_A23 as a wake source for the trackpad. We also
need to set up GPP_A GPE0_DW0, thus evicting GPP_B. We don't have any
interesting signals in GPP_B, so we won't be missing it.
I don't have hardware with A23 wired up, so i just tested the wake
source using A19 which is essentially identical to A23.
BUG=b:78541883
TEST=verified we can trackpad can wake system from suspend
Change-Id: If800464c8b2319d758b1823850571919f85bdc6c
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change enables xDCI controller on poppy, nautilus and soraka.
BUG=b:78577893
BRANCH=poppy
Change-Id: I9b0f81bda889b822479ead4d1acc2b613151a304
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25849
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
This change adds keyboard backlight feature for Nami platform
BUG=b:78360907
BRANCH=none
TEST=keyboard backlight works when EC reports correct info.
Change-Id: I3fceb83e155032b6e9f1763c4e2a29e7521269d2
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/25782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enables the i2c trackpad on atlas.
BUG=b:75454415
TEST=able to move pointer using trackpad
Change-Id: If4a82aa605ec68fd38e52c13406eaf803f9e86cc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/25759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change sets VmxEnable to 1 to match the kernel setting.
If this feature is enabled at the kernel level and not in FSP,
then there is an issue where FSP expects it to be disabled so
it forces a cold reboot on every warm reboot.
BUG=b:78129261
BRANCH=poppy
Change-Id: Idedbde1d8eb0c9e959733b7b50e5dec804d61cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25698
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating some GPIOs based on changes in the latest schematics. Also
renaming signals to match that of latest schematics.
BUG=b:73749640
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/poppy -x -a
Make sure different SKUs still boot.
Change-Id: I7d912f4bc6765f065c75c68a45bdf9ee844e0c1d
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/25646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The commit enables DPTF function. The DPTF parameters are provided by
thermal team.
BUG=b:72974136
BRANCH=poppy
TEST=emerge-nami coreboot then check the parameters in DPTF ui tool
Change-Id: I9b7ae34ee64f19ef783a8c1571831b2293105a18
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp hynix_dimm_H5AN8G6NCJR-VKC (ram id: 15).
BUG=b:77893710
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I434d42ff12e6dae39e5676f36ba6cf00b3a48b06
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp micron_dimm_MT40A512M16LY-075E (ram id: 14).
BUG=b:77930401
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: Ia44e70948e57c2f19664d874ae005ac39d748f92
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fixes: ba49c09b2f ("mb/google/poppy: Add variant for Atlas")
Change-Id: I9c5c10abf8129ff61b97312a70ed4749606a3090
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/25556
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Vayne.
We need to disable rear camera on all Vayne sku.
BUG=b:75073617
BRANCH=master
TEST=Verify if only front camera shown on Vayne
Change-Id: I6e7c1e8791462f00ad8336372954ee0a9465d9b8
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp hynix_dimm_H5AN8G6NAFR-UHC (ram id: 6).
BUG=b:77290144
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I33503de21c9fc14537c00c092986fd4d2998dace
Signed-off-by: chriszhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add a new variant of Poppy for the Atlas board.
BUG=b:75454415
TEST=tested on a P0 board. System boots and is mostly
functional, though some peripherals are not ready so there
are no touchpad/touchscreen devices configured yet.
Change-Id: I5a0bccd1bda0134aa51885ac2c6e7bb5b45de924
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD file for sdp samsung_dimm_K4A8G165WC-BCTD (ram id: 8).
BUG=b:76086834
TEST=Verified that the device with this memory part boots to OS fine.
Change-Id: I49fa114f07ad2eef10f18de9f6c3380173681bdd
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25379
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add an SPD for this particular Hynix memory type to the poppy board
so it can be used by poppy variants.
BUG=b:75454415
Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|