Age | Commit message (Collapse) | Author |
|
disable unused usb2 ports of bard and ekko skus
BUG=120874946
TEST=build a test firmware and run lsusb to check usb ports
Change-Id: I2ef3cd17ada8b65c96bc80675650905949f235e1
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30986
Reviewed-by: Vincent Wang <vwang@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
close the FP module power in power off (s5)
BUG=122887366
BRANCH=Nami
TEST= build test firmware and measure the fp power enable pin
Change-Id: I80ddfbf1edf7c6435d263d5f5e0edb8b8701817d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30910
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enable at24 EEPROM by adding ASL of nvm
BUG=b:122583978
BRANCH=master
TEST=Build and run for basic camera functions
Change-Id: Ifc2060c2ceb7d1a8ef490f36f484deb425a37c95
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/30795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch revises the pad reset config of speaker reset GPIO pin from
RSMRST to PLTRST. Audio engineer suggested to reset the amps with
warm reset.
BUG=b:122441567
BRANCH=None
TEST=warm & cold reset & suspend_stress_test -c 10 and ensure the
speakers are working well.
Change-Id: I87c554b186b068da93e1662a97afaf01dddae0ef
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:119899987
TEST=build and flash to rammus, log into rammus and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Signed-off-by: marxwang <marx.wang@intel.com>
Change-Id: Ieadb3609c7634a20e96c7c4dfb96f5e3f23e468b
Reviewed-on: https://review.coreboot.org/c/30607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I2e28b9f4ecaf258bff8a062b5a54cb3d8e2bb9b0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Sync'ing the sku_ids list in the master sku sheet for Pantheon.
BUG=b:121207221
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ic03c3a6fe238f2692ce15c45016115087380c0ca
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Use smm-$(CONFIG_HAVE_SMI_HANDLER) instead of smm-y
Change-Id: I0f91bc3e6c8ab31d837ab89af62d700b35c1e01b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Modify the vbios's eDP signal setting from level0(0dB)
to level1 (3.5dB) for bard
Add VBT blobs and include it in cbfs
BUG=b:119448457
TEST=Test & measure eDP signal
Change-Id: I0b854a6adad43844282aed61d26e798727b5cb62
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30375
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove duplicate entry of dptf_enable.
BRANCH=None
BUG=None
TEST=None
Change-Id: I3ddd6a702180624d31c5c58c71acdce8f627c925
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for micron_dimm_MT40A512M16TB-062EJ (ram id: 12)
BUG=b:121217853
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I45e6a7a183556fb085f5442cd6bb429d79ef4235
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add SPD file for sdp micron_dimm_MT40A256M16LY-075F (ram id: 11)
BUG=b:120884302
BRANCH=firmware-nami-10775.B
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Icf731bfefd550e9b94b6404bc870d4d76451deb1
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 999b916015ea0558e3821bdb51501b43a60b5ed6.
The DMIC doesn't have an ACPI id. The patch which enables ACPI
device with id DMIC may create conflict in the feature. Also the
ACPI id "DMIC" doesn't comply with ACPI naming conventions. The
issue for which the patch was introduced, is already addressed in
kernel DMIC driver and the patches are upstreamed in to the Linux
kernel.
Change-Id: I42cb076700dcb5906599471bebfcd5b265b17644
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/c/30151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Set CONFIG_NO_FADT_8042 to avoid probing for the 8042 controller.
This speeds up boot on nocturne by 1.3 seconds:
Before change:
[2.162266] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
After change:
[0.867735] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
BUG=b:120960844
BRANCH=none
TEST=build, flash, and boot nocturne; check dmesg to verify that
boot is faster and that you don't see the following log in dmesg:
[0.671501] i8042: Probing ports directly.
Change-Id: I62a16e6de5e74fa17970d9967f6d1628497ec1d3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/30283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sync'ing the sku_ids list in the master sku sheet.
BUG=b:112876867
Change-Id: I658e8dc67679b5b528ab267861a1151f50e42414
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
correct memory part name
form hynix_dimm_H5ANAG6NCMR-VKC
to hynix_dimm_H5AN4G6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I0c33343eb1269919fba324333897805da1d1ff9b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
According to issue tracker b:119899090.
https://partnerissuetracker.corp.google.com/issues/119899090
We modify rammus devicetree.cb .i2c[1] configuration to meet ELAN touchpad I2C special timing requirement.
BUG=b:119899090
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and check touchpad I2C characteristics meet requirement
Signed-off-by: YanRu chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ifeb08c2530e6a7674f23f7d48cefa16cfc59cb13
Reviewed-on: https://review.coreboot.org/c/29922
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:111812662
TEST=flash to nocturne, boot nocturne, run "memtester 1g" and
verify it passes.
Change-Id: Iefc3957f915a39a47ad6018459e65b70d1b34091
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
update the new sku ids of bard/ekko
BUG=b:120257865
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
write the new sku id in cbi and verify the fw to
check it can get the correct settings by the sku id
Change-Id: I3579d3d8042a270d8ea8e2f7b5612ff8e2cdfa7b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30031
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The WACOM 5C01 touch panel power-up delay of 10mS is too aggressive
and causes "failed to change power setting" errors in the kernel, so
this change increases the power-up delay to 20mS which allows enough
time for the WACOM device's i2c controller to wake up.
BUG=b:120090384
BRANCH=none
TEST=flash and boot nocturne, log into kernel, execute the following
command and make sure the string is not found :
dmesg | grep "failed to change power setting"
Change-Id: I1db0b3f5ce666b79d8ada2939ec865233ce52a56
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29988
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We discovered that the gpios previously used for FPMCU_INT_L were in
two different groups with two different voltages (C group was at 3.3V
and D group was at 1.8V). Moving both to B group which is at 3.3V.
BUG=b:119447525
BRANCH=Nami
TEST=unlock OS with fingerprint
register fingerprint
run powerd_dbus_suspend and see if it goes int s0ix
Change-Id: I2332b0eb7a2f74e8178b95a23c8ac2091027a071
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ifa5a3a22771ff2e0efa14fb765603fd5e0440d59
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: David Guckian
|
|
This change adds ACPI properties for GTCH7503 device.
BUG=b:119169362
BRANCH=firmware-nami-10775.B
TEST=Verify touchscreen works with this change
Change-Id: I26e16b7e118121b3dd9a88c76d04898b97753df0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29768
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
|
|
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
This change produces the following nodes in the SSDT :
Scope (\_SB.PCI0.XHCI.RHUB.HS01)
{
Name (_DDN, "USB Type C Port 1") // _DDN: DOS Device Name
Name (_UPC, Package (0x04) // _UPC: USB Port Capabilities
{
0xFF,
0x09,
Zero,
Zero
})
Name (_PLD, ToPLD (
PLD_Revision = 0x2,
PLD_IgnoreColor = 0x1,
PLD_Red = 0x0,
PLD_Green = 0x0,
PLD_Blue = 0x0,
PLD_Width = 0x0,
PLD_Height = 0x0,
PLD_UserVisible = 0x1,
PLD_Dock = 0x0,
PLD_Lid = 0x0,
PLD_Panel = "UNKNOWN",
PLD_VerticalPosition = "CENTER",
PLD_HorizontalPosition = "CENTER",
PLD_Shape = "OVAL",
PLD_GroupOrientation = 0x0,
PLD_GroupToken = 0x0,
PLD_GroupPosition = 0x0,
PLD_Bay = 0x0,
PLD_Ejectable = 0x0,
PLD_EjectRequired = 0x0,
PLD_CabinetNumber = 0x0,
PLD_CardCageNumber = 0x0,
PLD_Reference = 0x0,
PLD_Rotation = 0x0,
PLD_Order = 0x0,
PLD_VerticalOffset = 0x0,
PLD_HorizontalOffset = 0x0)
) // _PLD: Physical Location of Device
}
Scope (\_SB.PCI0.XHCI.RHUB.HS03)
{
Name (_DDN, "Bluetooth") // _DDN: DOS Device Name
Name (_UPC, Package (0x04) // _UPC: USB Port Capabilities
{
0xFF,
0xFF,
Zero,
Zero
})
Name (_PLD, ToPLD (
PLD_Revision = 0x2,
PLD_IgnoreColor = 0x1,
PLD_Red = 0x0,
PLD_Green = 0x0,
PLD_Blue = 0x0,
PLD_Width = 0x0,
PLD_Height = 0x0,
PLD_UserVisible = 0x0,
PLD_Dock = 0x0,
PLD_Lid = 0x0,
PLD_Panel = "UNKNOWN",
PLD_VerticalPosition = "CENTER",
PLD_HorizontalPosition = "CENTER",
PLD_Shape = "UNKNOWN",
PLD_GroupOrientation = 0x0,
PLD_GroupToken = 0x0,
PLD_GroupPosition = 0x0,
PLD_Bay = 0x0,
PLD_Ejectable = 0x0,
PLD_EjectRequired = 0x0,
PLD_CabinetNumber = 0x0,
PLD_CardCageNumber = 0x0,
PLD_Reference = 0x0,
PLD_Rotation = 0x0,
PLD_Order = 0x0,
PLD_VerticalOffset = 0x0,
PLD_HorizontalOffset = 0x0)
) // _PLD: Physical Location of Device
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0062
}
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x01)
{
Package (0x02)
{
"reset-gpio",
Package (0x04)
{
\_SB.PCI0.XHCI.RHUB.HS03,
Zero,
Zero,
One
}
}
}
})
}
Scope (\_SB.PCI0.XHCI.RHUB.HS05)
{
Name (_DDN, "USB Type C Port 2") // _DDN: DOS Device Name
Name (_UPC, Package (0x04) // _UPC: USB Port Capabilities
{
0xFF,
0x09,
Zero,
Zero
})
Name (_PLD, ToPLD (
PLD_Revision = 0x2,
PLD_IgnoreColor = 0x1,
PLD_Red = 0x0,
PLD_Green = 0x0,
PLD_Blue = 0x0,
PLD_Width = 0x0,
PLD_Height = 0x0,
PLD_UserVisible = 0x1,
PLD_Dock = 0x0,
PLD_Lid = 0x0,
PLD_Panel = "UNKNOWN",
PLD_VerticalPosition = "CENTER",
PLD_HorizontalPosition = "CENTER",
PLD_Shape = "OVAL",
PLD_GroupOrientation = 0x0,
PLD_GroupToken = 0x0,
PLD_GroupPosition = 0x0,
PLD_Bay = 0x0,
PLD_Ejectable = 0x0,
PLD_EjectRequired = 0x0,
PLD_CabinetNumber = 0x0,
PLD_CardCageNumber = 0x0,
PLD_Reference = 0x0,
PLD_Rotation = 0x0,
PLD_Order = 0x0,
PLD_VerticalOffset = 0x0,
PLD_HorizontalOffset = 0x0)
) // _PLD: Physical Location of Device
}
Scope (\_SB.PCI0.XHCI.RHUB.HS07)
{
Name (_DDN, "POGO") // _DDN: DOS Device Name
Name (_UPC, Package (0x04) // _UPC: USB Port Capabilities
{
0xFF,
0xFF,
Zero,
Zero
})
Name (_PLD, ToPLD (
PLD_Revision = 0x2,
PLD_IgnoreColor = 0x1,
PLD_Red = 0x0,
PLD_Green = 0x0,
PLD_Blue = 0x0,
PLD_Width = 0x0,
PLD_Height = 0x0,
PLD_UserVisible = 0x0,
PLD_Dock = 0x0,
PLD_Lid = 0x0,
PLD_Panel = "UNKNOWN",
PLD_VerticalPosition = "CENTER",
PLD_HorizontalPosition = "CENTER",
PLD_Shape = "UNKNOWN",
PLD_GroupOrientation = 0x0,
PLD_GroupToken = 0x0,
PLD_GroupPosition = 0x0,
PLD_Bay = 0x0,
PLD_Ejectable = 0x0,
PLD_EjectRequired = 0x0,
PLD_CabinetNumber = 0x0,
PLD_CardCageNumber = 0x0,
PLD_Reference = 0x0,
PLD_Rotation = 0x0,
PLD_Order = 0x0,
PLD_VerticalOffset = 0x0,
PLD_HorizontalOffset = 0x0)
) // _PLD: Physical Location of Device
}
BUG=b:119275094
TEST=build and flash to nocturne, log into nocturne and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Change-Id: I65d9b580fd69fd0a2c84f14b78a8e8b5e9217b16
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
|
|
We are seeing problems (interrupt storm) with using the same gpio for
FP MCU wake and irq signals. Reverting back to using separate gpios
for wake and irq until we resolve the issue.
BUG=b:119447525, b:115706071
BRANCH=Nami
TEST=Run powerd_dbus_suspend from kernel and make sure see DUT drop
into S0ix in the EC console. Also, unlock from lock screen with
fingerprint.
Change-Id: Id7987f28526256808b8ed49e66f66298f7cdbcee
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
|
|
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_D6 needs to be inverted to enter S0ix because FPMCU_INT_L is
active low. Keeps device awake otherwise.
BUG=b:119447525, b:115706071
BRANCH=Nami
TEST=Run powerd_dbus_suspend from kernel and make sure see DUT drop into
S0ix in the EC console.
Change-Id: Iad5df124e2439bbdc078d6a33f8d0510d25ecf6f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29650
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_F10 (HP_IRQ_GPIO) to use PLTRST.
BUG=none
TEST=none
Change-Id: Idc6c42cb4dc6e8eb368d605c83f584f4c69077dc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29540
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With this change, coreboot thinks we're running at 1MHz:
DW I2C bus 2 at 0xd1133000 (1000 KHz)
Elan eKT3644 IC Specification (trackpad) requires:
Low Time larger than 500ns (61 * 8.3ns = 506ns).
High Time larger than 260ns (32 * 8.3ns = 265ns),
Data Hold_time larger than 0ns.
Start Condition Hold time larger than 250ns.
Rise/Fall time of less than 120ns.
HCNT controls both High Time and Start Condition Hold time.
LCNT controls Low Time.
SDA_HOLD controls Data Hold Time.
P2 Atlas "Rise time" is 90ns and "Fall time" is 32ns and tuned
using resistors on the board and must be considered when
adjusting any of the parameters since these times are all measured
at 30 or 70% of base and peak voltages (0v/1.8v).
The eKT3644 requirements are met with LCNT=69, HCNT=33, SDA_HOLD=20
which yields the SCL at around 950KHz - suboptimal but compliant.
Lower LCNT or HCNT results in "lost arbitration" errors or not complying
with eKT3644 requirements.
Verified by gaggery.tsai@intel.corp-partner.google.com.
Scope shots posted here:
https://b.corp.google.com/issues/78601949#comment177
BUG=b:78601949
BRANCH=none
TEST=Farzam provided test points on track pad for SCL/SDA/GND.
Waveforms measured with oscilloscope and screen shots attached
to bug (comment #177, #155, #100).
Operate trackpad/touchscreen
Review dmesg (kernel) output for correct speed, parameters, and
no errors (e.g. "lost arbitration" or "host controller timeout")
Change-Id: Iaf42ba7b8818b7cd9c8dcc657823dac705659d38
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Tested-by: gaggery.tsai@intel.corp-partner.google.com
Tested-by: grundler@chromium.org
Reviewed-on: https://review.coreboot.org/29553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
|
|
GPP_D0 is NC in 1st SKU board design, so we should control GPP_D0
for only 2nd SKU.
BUG=none
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ifd85693c9155ed960f0c794d4b83fe8863b77134
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/29631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The GPP_E1 gpio was incorrectly being defined as a no-connect.
Configure GPP_E1 for the WLAN_WAKE_L signal as per the schematic.
BUG=b:119508897
TEST=Build and flash nocturne, boot nocturne and
1) Verify nocturne can successfully suspend/resume from S3 and S0ix.
2) Verify wake from wlan wakes device from S3 and S0ix.
To do so,
a) as root, execute "iw phy phy0 wowlan enable disconnect" on DUT
b) connect DUT to mobile hotspot
c) sleep device via "powerd_dbus_suspend"
d) turn off hotspot, verify DUT wakes from S0ix
e) enable hotspot again
f) connect DUT to hotspot
g) sleep DUT via "sudo echo mem > /sys/power/state"
h) turn off hotspot, verify DUT wakes from S3
Change-Id: I4efb4f6d601e172ae4807901e3bd4c9954319f80
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rename EC_ENABLE_TABLET_EVENT config as EC_ENABLE_MULTIPLE_DPTF_PROFILES
since it aligns with the use-case.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes (base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: If147f1c79ceaaed00e17ec80ec6c912a8f7a8c2e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Remove defining EC_ENABLE_TABLET_EVENT configuration from the boards where
it is not required.
BUG=b:118149364
BRANCH=None
TEST=Build
Change-Id: Iee70192916ac6c53bb27b7f73f3ad6d069afd030
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_D9 and GPP_D10 to use PLTRST.
BUG=b:119202293
TEST=none
Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3.
Changed GPP_C11 configuration to use PLTRST instead.
BUG=b:114196791
TEST=Build, flash, boot nocturne, log in to kernel and execute
the following two commands and verify it passes :
echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd
sudo suspend_stress_test -c 2
Change-Id: I008532fce963c51a435378001440ac72b5ebfffc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
add the memory parts as ram id 10:
hynix_dimm_H5ANAG6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I137259b88f39779768a58959a2dcc565645eee6d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some variants of nami will have a fingerprint MCU.
BUG=b:118503113
BRANCH=Nami
TEST=None (build and boot, but no hw yet)
Change-Id: I446dc09cdf7f84a801723cb403d2de80e0997c65
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add option for Nanya NT6CL256T32CM-H1 part.
Add comments to indicate total memory size for convenience.
BUG=b:118624505
BRANCH=master
TEST=none
Change-Id: I82200e7b3d0a13295cb38f53ab576697ff8d302b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable the radium touchscreen support
BUG=b:117960394
BRANCH=master
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. boot up on ekko DUT to check touchscreen device by evtest
/dev/input/event3: Raydium Touchscreen
Change-Id: I16167d5d3ce6eac9d64832b52bb1945999a63a90
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to syndra thermal table, PL2 need to check cpu id.
Set up syndra PL2 value.
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
Refer to b:116836990#comment10.
BUG=b:116836990
TEST=The thermal team verify OK
Change-Id: I766a886121a089683565608252b4c176c70e88a3
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Variants of Nami need to accommodate single channel DDR. Will use
GPP_D10 on nami for identification. GPP_D10 will return 1 when device
is using single channel DDR and 0 when using dual channel DDR.
BUG=b:117194353
BRANCH=None
TEST=dmidecode | grep Channel and make sure that the correct number of
channels gets returned.
Change-Id: If86ab2c5404c4e818ce496ea935227ab5e51730a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change uses CRFP ACPI name for FP device since user space
utilities expect this name for triggering different actions.
BUG=b:112974410
BRANCH=nocturne
Change-Id: I63309227c916b43917e529c223cf738fc3baa209
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29231
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, set GPIO GPP_C22 to 1 for touchscreen power on.
And add touchscreen device "PNP0C50" to I2C0.
According to touchscreen spec, device power on initialization takes
105 ms, so set "generic.enable_delay_ms" to 120.
We found there is i2c error log pop up when we set delay
time to be 110ms or 105ms. If we set delay time to be
120ms. System will not pop up i2c error log.
BUG=b:115944726
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure touchscreen works.
Change-Id: Ibce552d04991e85c99ae3a0a92455fc747d9fced
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Before entering the OS, the AP relies on the smi handler to shutdown the
system when the lid closes. Without the smi_events setting, the AP will
not receive the smi handler. As a result, the AP won't shutdown and will
always keep in S0.
This problem is caused by the https://review.coreboot.org/c/coreboot/+/28983
and this patch adds the smi_events back to support the smi handler for
the lid close.
BRANCH=master
BUG=b:115572596
TEST=test_that -b ${BOARD} ${IP} firmware_ECLidShutdown
Change-Id: Id82311a8ccd109f9c26516f59a45bdf34da98529
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/29191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change link frequency of IMX319 from 360Mhz to 482.4 Mhz to match the
changes from kernel driver. IMX319 has two PLLs and it can be configured
either single or dual. Previous driver implemente dual PLL mode, however
image sensor vendor prefer single PLL mode and calculate the pixel rate
became easier. So the kernel driver changed to use single pll, coreboot
change will match that.
Bug=b:116082248
Change-Id: Iac9a72253e0529bf2c0785fb701b7bc251bcbab5
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28736
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While these pins were set to a pull-down 20KOhm, NPCX EC consumes
~2.1mW higher power. Becasue there was leakage current on both GPIO67
and GPIO70 from NPCX EC. With the external pull-up 10KOhm for
USB_OC0#/USB2_OC1#, this wasn't enough to prevent leakage current.
BUG=b:117139495
TEST=Check nxpc EC power to see power improvement
Change-Id: I685d876461c263f07ca4c8f8046635cb7087279c
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/29007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update CPU passive temperature threshold value from 70C to 80C,
to avoid early throttling for spiky workloads. Also, change CPU
throttling interval from 1 sec to 5 sec for CPU temperature.
BUG=b:116400298
BRANCH=None
TEST=Manual performance testing on nocturne.
Change-Id: Ic5031a4aa16f750237565f4e4928e78834b1d686
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/29044
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Syndra.
We need to disable rear camera/DMIC on all Syndra sku.
BUG=b:112876867
Change-Id: I92fb43ec84387c268ffdb6d0d34a5e5b13bcf50a
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
More platforms are not able to hibernate under certain circumstances,
such as when AC is plugged. This original path was conservatively put in
to prevent potential damage when cr50-update-caused asynchronous resets
occur. Julius' compelling argument that async resets from recovery mode
requests should have enough coverage of the design over the course of
project development. Remove the hibernate path and assume all is well
going forward.
Change-Id: I37121e75ff4e6abcb41d8534a1eccf0788ce2ea2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/29076
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change implements the callback to provide google_chromeec_event_info
structure in nocturne variant and sets MKBP SCI based on board id.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: Ifcc10aefc8f450214bd64dfffaf8854ada43f323
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a variant callback to read google_chromeec_event_info
from variant at runtime to allow override of any events based on
factors like board id.
This callback is used in ramstage and smm to get
google_chromeec_event_info structure for performing various actions
like setting masks and logging wake events from EC.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: If89e904c92372530a0f555952f87702f068e0b03
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add SPD file for sdp samsung_dimm_K4AAG165WB-MCRC (ram id: 9)
BUG=b:112679174
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Iac1e3ca4b009cc9be94608cd342f535fa581a5eb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28974
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Wifi wake register is incorrectly set in devicetree.
Set wifi wake to its correct wake source, GPE0_DW2_01.
BUG=b:117330593
TEST='emerge-nocturne coreboot chromeos-bootimage', flash nocture,
connect wifi to a hotspot, suspend device, echo freeze >
/sys/power/state, and then shutdown the hotspot and verify device
wakes.
Change-Id: Iafa865ca79d33541d7f47b69d2fb209e7f9c98af
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28938
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The WAKE# signal has moved to LAN_WAKE, so WAKE# is now
floating and must be disabled. This change disables WAKE#.
BUG=b:117284700
TEST=none
Change-Id: I1c25e4ba28cd2b8807cd155d47c29c0d3ee9e8a5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change uses the generic device driver to provide DMIC properties
in ACPI table to the OS driver.
BUG=b:112888584
Change-Id: I239f571bc29f02793f017a4713b5af03b23cfa3e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28797
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nautilus-LTE sku shows abnormal reset symptom at high temperature chamber
test, but the root cause is unclear.
Experimentally, setting SlowSlewRate IA/GT/SA to 1/2 improves this abnormal
reset issue, so we would apply it until find root cause of this issue.
BUG=b:117130599
BRANCH=poppy
TEST=Built and passed on reliability test with modified coreboot
Change-Id: I7fa0041989113097e3b283dbcf4ca2a73629fe54
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28785
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the ACPI controls for power sequencing the touchscreen.
The initial setting is to keep the touchscreen powered off and in
reset. When linux is ready to talk to the touchscreen, it powers it
on and releases reset via ACPI.
BUG=b:110286344
TEST=verified touchscreen is functional in chromeos
Change-Id: I58c42a8f09342cfe54f82ef0e6cd8ea72a5140dc
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28869
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPP_C19 is not being set as the code is incorrectly setting
GPP_C16 instead, causing SAR sensor not to work, so this change
sets GPP_C19 to NF1.
GPP_E3 is not being initialized in the code. Initialize GPP_E3
to a no connect as documented in the board schematic.
BUG=b:117124878
TEST: 'emerge-coreboot chromeos-bootimage', flash nocturne and
verify that i2c transactions work for the left SAR sensor.
Change-Id: I9e972dbe4214cdd15d80d63dfa058e7755f7ecbb
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28867
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase the reset delay for the touchscreen to 10 ms.
BUG=b:116857433
TEST='emerge-nocturne coreboot chromeos-bootimage', flash and boot
nocturne to kernel, log in and execute the following two commands:
echo "i2c-WCOM50C1:00" > /sys/bus/i2c/drivers/i2c_hid/unbind
echo "i2c-WCOM50C1:00" > /sys/bus/i2c/drivers/i2c_hid/bind
and verify the bind command does not echo back a
"-bash: echo: write error: No such device" error.
Change-Id: I102b57ea5a10d22bee6d4f7c6f114b380a5d586b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28803
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Caveh Jalali <caveh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch modifies "oem_table_id" from "RAMMUSMAX" to "RAMMUS"
so that the audio topology file can be loaded properly by the
operating system.
BUG=b:112945714
BRANCH=master
TEST=There is no error message like "failed to load topology firmware" in
kernel v4.4 log.
Change-Id: I66a38ea38791dd3d9606a05b7b696236c350237f
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use GPIO GPP_D17 pin as the EC sync interrupt and provide this value
to the embedded controller to be exported to the OS.
This interface was tested on a reworked Nocturne board with modified
EC and a modified kernel driver to ensure that the interrupt asserts
as expected and can be used by the kernel driver.
Change-Id: Ie2b33692367b5d9ecc2b128180d8cfe4f6b347b1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/28759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We refer to Intel Doc#594883.
The recommended Ac/Dc loadline values are as below:
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------+-------+
#| Domain/Setting | SA | IA | GTUS | GTS |
#+----------------+-------+-------+-------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 2A | 2A | 2A | 2A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AcLoadline | 14.4 | 4.2 | 5.7 | 4.47 |
#| DcLoadline | 14.0 | 4.17 | 4.2 | 4.3 |
#+----------------+-------+-------+-------+-------+
BUG=b:112167318
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: I2d83d835ec841ac4cc811a0a69f74d203d5ea173
Signed-off-by: statham_chu <statham_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase power limit1 maximum value from 5W to 7W. This value as per
recent measurement on closed system which shows better performance
results.
BUG=None
TEST=Build and tested on Nocturne system. Performance tests
show better results.
Change-Id: I7485b1d2afde46ec28d548c13be35a43e7572918
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add tdp_pl1_override value as 7W.
BUG=None
BRANCH=None
TEST=Build coreboot for Nocturne board
Change-Id: I16d3894da68bc3be6eff526062f9a88ef2df60c7
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
|
|
The previous does not work well enough when testing with
high ambient temperature. Update DPTF settings to make
it work better.
List of tweaks:
1. Raise DRAM Critical temperature from 48C to 55C
Note that there are mechanisms in EC that complement
this because of DPTF limitation that we can't have
multiple passive temperatures.
2. Lower response time for DRAM temp sensor from 60s to 5s.
3. Increase throttle priority to the charger when DRAM hit
passive temperature from 100 to 200.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: Idf7efa76b2c6085cf97aa9f65c6ce066e8cff99a
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28738
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit aef592d9b66aa18d83b0a211ead26013ff1f7d98.
Reason for revert: Use values from driver instead of hardcoding in
firmware (b:113303916)
Change-Id: I02d21803f38da227f1d85b00cb6b5274d81dbbb4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28690
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD "CmdTriStateDis" to disable TriState for
the rammus boards. Rammus is LPDDR3 design without RTT for CMD/CTRL.
BUG=none
TEST=Run memtester app and also webgl fishtank on the LPDDR3 kabylake
boards and also check the margin data is proper in FSP.
Change-Id: Iee115f49ba5b36dc5b0425e9da02b58cd19b2236
Signed-off-by: Marx Wang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28568
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change GPP_D17 and GPP_D18 to no connects as DMIC was moved
to DMIC0.
BUG=b:113744731,b:111106010
TEST=none
Change-Id: I8ef42627e542182707c81389af9da33a114bc184
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28689
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF settings based on recommendation from thermal team.
BUG=b:112550414
BRANCH=None
TEST=Manually tested by thermal team.
Change-Id: I26f09392a3293ce4b3481f2be341a667d606bc10
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-on: https://review.coreboot.org/28666
Reviewed-by: Todd Broch <tbroch@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As we don't use the MIPI camera on Rammus, disable SA Imaging Unit and
CIO2 devices to avoid the system failed to enter S0ix.
BUG=b:114502527
BRANCH=master
TEST=On DUT, echo freeze > /sys/power/state
1. check the S0ix status on EC console
2. check the value of /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Change-Id: I91629732db01ee534f0ddb67a2b358d725ef810e
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch sets the MRC UPD CmdTriStateDis for the atlas boards.
Atlas is a LPDDR3 design without RTT for CMD/CTRL.
The original change for
nocturne is I0f593761dcbd121e7e758421af178931b9d78295
mb/google/poppy: Set UPD CmdTriStateDis for Nocturne
BUG=b:111812662
Change-Id: I45b6dd22412c689c8db64f4650e9fa9e87dec2ec
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Only for those that are x86 and also have a RW_LEGACY region.
The assumption is that all devices touched have 64k block sizes when
choosing size and alignment of the region.
Change-Id: I12addb137604f003d1296f34f555dae219330b18
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add MICRO 4G and 8G SPD file.
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: I7cb5b7f2bcdc6fbe0cbc640cad4af014f1a0edd6
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add two memory parts and ram id:
hynix_dimm_H5ANAG6NCMR-VKC
micron_dimm_MT40A1G16KNR-075E
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ia052f16b6c1e64ee6458fbdeea56a482a728c35a
Signed-off-by: Ren Kuo <Ren.Kuo@quantatw.com>
Reviewed-on: https://review.coreboot.org/28536
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On rammus, headset uses DA7219 so that we need to enable it.
BUG=b:112945714
BRANCH=master
TEST=emerge-rammus coreboot chromeos-bootimage
Flash FW and check in kernel to see if DA7219 is up.
Change-Id: I92dd412374d007aab264661e698fbbbbcf1eae45
Signed-off-by: marxwang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/28537
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch sets the MRC UPD CmdTriStateDis for the
nocturne boards.Nocturne is LPDDR3 design without RTT
for CMD/CTRL.
BUG=b:111812662
TEST=Run memtester app and also webgl fishtank on
the LPDDR3 kabylake boards and also check the
margin data is proper in FSP.
Change-Id: I0f593761dcbd121e7e758421af178931b9d78295
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/28379
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for a x2 NVMe device on PCIe bus PCIe lines 5+6 and
clock#4.
BUG=b:113369699
TEST=booted on atlas
Change-Id: I08e7c4d65662ddbb7d936915c896eb1fcb240ba8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
On rammus, system halt was observed because of gspi clk value being set to 0.
Log info from serial coreboot:
FMAP: area RW_NVRAM found @ 9fa000 (24576 bytes)
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
VBNV: Restore from flash failed
ASSERTION ERROR: file 'src/soc/intel/common/block/gspi/gspi.c', line 443
gspi.c
442
443 assert(gspi_clk_mhz != 0);
444 assert(ref_clk_mhz != 0);
445 return (DIV_ROUND_UP(ref_clk_mhz, gspi_clk_mhz) - 1) & SSCR0_SCR_MASK;
BUG=none
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure system boots up.
Change-Id: Ibe3937902901b2cdc1a196415c08fabb0f3155f2
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28405
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DMIC's are now connected to DMIC_CLK0/DMIC_DATA0.
So, enable the pins accordingly.
BUG=b:113744731,b:111106010
BRANCH=none
TEST='emerge-nocturne coreboot chromeos-bootimage' builds the image
Change-Id: I48cace3c6099a2853fcb377c695a5e325094baf6
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/28433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus-Wifi with m3 AP got a halt issue during CTS test.
Nautilus-Wifi was FCS with Celeron AP first and also its PCB/BOM was
validated only with Celeron. Since Celeron deos not support turbo
boost mode, its steady power demend and lower CPU frequency may not
reflect the potential noise hidden inside the board.
Bumping VCC_SA voltage offset 75mV confirmed works to mitigate the
potential noise coupling to VCC_GT/SA, and we verified this change
makes this issue go away on Nautilus-Wifi board.
Nautilus-LTE doesn't show this issue, since it has 10L PCB, will have
better grounding and less noise/ripple than 8L PCB.
BUG=b:111417632
BRANCH=poppy
TEST=Verified CTS test pass without an issue.
Change-Id: Id13fcc36a5b6ed42620c66f57a7303f30bff1a50
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds the mainboard.c in order to support the sku id in smbios
table where the sku id is queried from the eeprom via EC.
BUG=b:113714761
BRANCH=master
TEST=check the result of 'dmidecode'
Change-Id: I3413784cca1ac10a2468d84f2d06c0e1d701fdcb
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds the DRIVERS_SPI_ACPI to enable the tpm device node.
Without DRIVERS_SPI_ACPI, the kernel will popped out the below error:
cr50-update[592]: Starting cr50 update
cr50_get_name[595]: updater is /usr/sbin/gsctool -s
cr50-update[609]: exit status: 3
cr50-update[613]: output: Could not open TPM: No such file or directory
cr50_get_name[615]: board_id: '' board_flags: '0x', extension: 'prod'
cr50-update[617]: hashing /opt/google/cr50/firmware/cr50.bin.prod
cr50-update[678]: current state 3 in /var/cache/cr50.a3055efbc9.state
cr50-update[682]: not running
cr50-result[782]: Not running normal image. Skip setting Board ID
trunksd[795]: TPM: Error opening tpm0 file descriptor at /dev/tpm0: No such file or directory
BUG=none
BRANCH=master
TEST=/dev/tpm0 is created
Change-Id: I35287c6c54299c2677c41fc830675570b9d45a94
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/28400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set threshold parameter for grip sensor STH9321
.ProxCtrl6: 75
.ProxCtrl7: 99
BUG=b:113303916
BRANCH=poppy
TEST=Built and verified parameter passed to driver
Change-Id: I8a410a23b5e3831fc8e90118b810fc2409a026eb
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/28381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Enrico Granata <egranata@chromium.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is meant to solve an issue where the proximity sensor may fluctuate
between CLOSE / FAR in rapid succession upon the user removing their hand
from the unit, before settling on the correct output.
Using the hardware debouncing filter solves this issue and removes the
spurious fluctuations.
BRANCH=None
BUG=None
TEST=manual on Nocturne, observing events come in
Change-Id: I78cc4852d42fcda6209fedce1ce91236b5814571
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/28112
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nami doesn't support wakeup from hibernation by CR50. This causes the
device to remain turned off after CR50 update.
This patch disables turning off EC on cr50 update. CR50 resets the
whole system. So, EC reset is not required.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
BUG=b:112604277
BRANCH=none
TEST=gsctool -a -u /media/removable/cr50.bin && reboot
Verify EC reboots. AP prints 'Waiting for CR50 reset to pick up update'
then reboots.
Change-Id: I06f5eb6100e8af6ffec45d4de2b40eff44f89709
Reviewed-on: https://review.coreboot.org/28113
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This file contains two instances of "dptf_enable" = "1". This change
removes the 2nd instance (it doesn't have an explicit comment like the
1st instance).
The dptf devices still seem to be present even with this change, as
expected.
Change-Id: I890006644be9176ebaf555cc121c816e12f2b596
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The spec of the sx9310 says the I2C interface can handle standard
(100kb/s) and fast mode (400kb/s). The current setting is using fast
plus (1000kb/s) so this change is reducing the speed to fast mode.
I've been using the sensors with this change for a few weeks now, though
I also don't recall seeing an issue prior to this change.
Change-Id: I337fc02c52565d6ec4d7bac1b3564f65238962dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 1fdb76945a9d06bbff37dee9da69e13a86c933f4.
Camera power is now handled by ACPI rules - no need to force the GPIOs
on by default.
BUG=b:80106316,b:111141128
Change-Id: Ifefec320884989f106a4b09c956d3a3279a1491a
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28072
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ping-chung Chen <ping-chung.chen@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This defines new GPIO pin for controlling the display panel CABC
function. The default value is high (enabled).
BUG=b:112154569
Change-Id: I29083ab18e37f929a55b450b143463c67fe0abea
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28070
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|