Age | Commit message (Collapse) | Author |
|
We had two ways to configure the serial IRQ mode. One time in the
devicetree for FSP and one time through Kconfig for coreboot. We'll
use `enum serirq_mode` from soc/intel/common/ as a devicetree option
instead. As the default is `quiet mode` here and that is the most
common mode, this saves us a lot of lines.
In four cases kblrvp8, 11 and librem 13v2, 15v3, we had conflicting
settings in devicetree and Kconfig. We'll maintain the `continuous`
selection, although it might be that coreboot overrode this earlier
on the kblrvps.
Note: A lot of Google boards have serial IRQ enabled, while the pin
seems to be unconnected?
Change-Id: I79f0cd302e335d8dcf8bf6bc32f3d40ca6713e5c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/31596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the common VMX implementation, and set IA32_FEATURE_CONTROL
lock bit per Kconfig *after* SGX is configured (as SGX also sets
bits on the IA32_FEATURE_CONTROL register).
As it is now correctly based on a Kconfig, the `VmxEnable` devicetree
setting vanishes.
Test: build/boot google/[chell,fizz], observe Virtualization enabled
under Windows 10 when VMX enabled and lock bit set.
Change-Id: Iea598cf74ba542a650433719f29cb5c9df700c0f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29682
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename EC_ENABLE_TABLET_EVENT config as EC_ENABLE_MULTIPLE_DPTF_PROFILES
since it aligns with the use-case.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes (base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: If147f1c79ceaaed00e17ec80ec6c912a8f7a8c2e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Remove "IshEnable" from soc_intel_skylake_config since it's not
used anymore.
Enable/disable ISH by checking if ISH device is turned on or not.
Refer to https://review.coreboot.org/#/c/coreboot/+/26485/.
BUG=b:79244403
BRANCH=none
TEST=Built.
Change-Id: I4d2889af118659852431c87cb516fd19b577efc5
Signed-off-by: li feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/26521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables xDCI controller on poppy, nautilus and soraka.
BUG=b:78577893
BRANCH=poppy
Change-Id: I9b0f81bda889b822479ead4d1acc2b613151a304
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25849
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change sets VmxEnable to 1 to match the kernel setting.
If this feature is enabled at the kernel level and not in FSP,
then there is an issue where FSP expects it to be disabled so
it forces a cold reboot on every warm reboot.
BUG=b:78129261
BRANCH=poppy
Change-Id: Idedbde1d8eb0c9e959733b7b50e5dec804d61cae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25698
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Soraka, Poppy & Nautilus are designed to operate at max power of
45 Watt. Hence set psys_max to 45W.
BUG=b:66066340
BRANCH=None
TEST=Build and boot soraka.
Change-Id: If6f624733830b462329b5f539c20e2aea664143e
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/23757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
|
|
This change updates the passive setting for TCPU as per factory team
recommendation.
BUG=b:65467566
Change-Id: I081f63bdf811ff021c398f60efec9e6cccf462d5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23494
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change selects EC tablet event and provides trip point
temperatures for tablet and non-tablet mode so that DPTF can
be supported depending upon device mode.
BUG=b:65467566
TEST=Verified by changing modes that the trip point temperatures are
updated in the
OS (/sys/devices/virtual/thermal/thermal_zone{2,3,4,5}).
Change-Id: I071868982fa87821550b870a6d8050cf2a030b49
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23463
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change configures unused pins as not connected.
Change-Id: I6779d9fba73da8fb2faa08ad5d2236b813105720
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23416
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPP_F3 is not connected on poppy or any of its variants. This change
configures GPP_F3 as NC on poppy and all the variants.
BUG=b:70160119
Change-Id: I303276ab9546d56c846755fa3a6142978f6b8c92
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates scl_lcnt value for I2C5 to bring the bus frequency
closer to 400kHz.
BUG=b:65062416
TEST=Verified that I2C5 frequency is between 389-396kHz.
Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Variants nautilus and soraka currently provide the exact same
definition for variant_cros_gpios as provided by the baseboard. This
change removes the function defintions from variants so that the weak
definition in baseboard can be used.
Change-Id: Ic88623f34039792f0f9fb46842b24e4f1290981b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22705
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Soraka is no longer using SPI TPM. This change disables GSPI0 in
device tree and updates gpio config accordingly.
Change-Id: Ia0554ce3a0d553631123cc2b23b6dc2f6f40a1a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates device tree deep_sx_config to disable internal
pull-down on AC_PRESENT.
BUG=b:69983729
Change-Id: I041900a5262f8fd920856f126185329242a0639a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I6246300a4376a0194950d4de277af040b10b6c1f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds infrastructure to allow variants to define their own
camera.asl file.
- Poppy and soraka use the one provided by baseboard.
- Dummy file is added for nautilus since it does not have camera
support enabled yet.
TEST=Verified that DSDT table remains the same with and without this
change.
Change-Id: I0f0b489e74739aa4708283d58d8b7626b77a89a3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: shkim <sh_.kim@samsung.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
On shutdown, Soraka enters Deep S5 and not S5 state. Setting
pad reset config of a gpio to RSMRST will not preserve
the gpio config across deepSx and the gpio should be configured again.
The WLAN_PE_RST signal should be brought up early in the bootflow
for giving the device enough time to initialized before PCIE init in FSP-S.
Hence, the gpio WLAN_PE_RST (GPP_B8) pad configuration is done in
early pad configuration in bootblock also.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S5, S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I5c7a4a3871a3bff69c1136379c78a8368c6258a6
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Poppy and variants won't be using deep S3. This change disables deep
S3 option in devicetree.
BUG=b:69053636
Change-Id: I5fb4a6a0e4216a3648b5ed888f6dc6618f1a9fc4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22378
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In skylake based platforms, setting GPIO pad reset config
to DEEP will reset the gpio configuration across warm reset,
set it to RSMRST to preserve the configuration across warm resets.
Also, moving the configuration from early to late as appropriate.
BUG=b:64386481
BRANCH=none
TEST= WiFi functionality across S3, DeepS3, S0ix and warm/cold reboot.
Change-Id: I38940b7c7d71e60bf0e51d6978a00be148ad61bc
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change 1760cd3e (soc/intel/skylake: Use common/block/gpio) updated all
skylake boards to use common gpio driver. Common gpio code
defines PAD_CFG_GPI without GPIO_DRIVER ownership. However, for
skylake PAD_CFG_GPI set GPIO_DRIVER ownership by default. This
resulted in Linux kernel failing to configure all GPIO IRQs since the
ownership was not set correctly. (Observed error in dmesg: "genirq:
Setting trigger mode 3 for irq 201
failed (intel_gpio_irq_type+0x0/0x110)")
This change fixes the above issue by replacing all uses of PAD_CFG_GPI
in skylake mainboards to PAD_CFG_GPI_GPIO_DRIVER.
BUG=b:67507004
TEST=Verified on soraka that the genirq error is no longer observed in
dmesg. Also, cat /proc/interrupts has the interrupts configured
correctly.
Change-Id: I7dab302f372e56864432100a56462b92d43060ee
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change 868b3761 (mainboard/google/soraka: Reduce Wacom resume time)
removed the delay after taking device out of reset since it seemed
unnecessary in system resume case (because there is enough time after
taking device out of reset and before communication with device
starts).
However, without the delay, kernel driver runs into issue while
talking to the device during boot-up and runtime
suspend/resume. (Observed this error in dmesg: "i2c_hid
i2c-WCOMCOHO:00: failed to change power setting."). Thus, add 10ms
delay after taking device out of reset. Verified on multiple Soraka
system that with 10ms delay, kernel driver does not run into any issue
talking to the WCOM device during boot-up, runtime suspend/resume and
system suspend/resume.
BUG=b:65358919
TEST=No more errors talking to WCOM device in kernel dmesg.
Change-Id: I485b753cbae4b653e74337e048aea4d26ffdbb81
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21910
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rajat Jain <rajatja@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the WCOMCOHO registers a reset delay of 110ms to execute their
_ON_ asl power on method. This seems to be correct as per WACOM product
design specifications but it introduces an unwanted delay in overall system
resume time. This delay should be removed from ACPI critical path since the
entire kernel resume gets blocked on this sleep call unless this is over. In
the kernel I2C communication with WACOM driver starts with the resume
callbacks of I2C HID driver which gets triggered after display is completely
resumed. The display resume process takes at least 230ms so it's safe to
reduce the delay from coreboot and unblock the critical ACPI path.
BUG=b:65358919
BRANCH=None
TEST=manual testing on Soraka board to ensure that touchscreen works at boot
and after suspend/resume. Also verify that the overall S3 resume time is
reduced by 110ms.
Change-Id: I59d070977a95316414018af69d5b43e3147ccf4e
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/21692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update I2C5 bus parameters to obtain clock frequency <400kHz.
BUG=b:65062416
TEST=Verified using an oscilloscope that I2C5 bus frequency
in factory is ~397kHz.
Change-Id: I3d0b0388343d4c6c5e7eabf3e06799d059307517
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable LTR for Root port 0, where wifi card is connected.
BUG=b:65570878
TEST=After enbaling LTR on port 0 on the MB devicetree, No errors reported
by AER driver for root port 0.
Change-Id: I222a87fe2094c8424760ccf578e32b9ac042f014
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/21548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Cloned from baseboard/dptf.asl and update the parameters for soraka.
1. Update DPTF CPU/TSR0/TSR1/TSR2 passive/critial trigger points.
CPU: passive point:85, critial point:100
TSR0: passive point:55, critial point:65
TSR1: passive point:58, critial point:70
TSR2: passive point:60, critial point:75
TSR3: passive point:60, critial point:75
2. Set PL1 Max to 7W, and PL1 Min 4.5W
3. Change sampling period of thermal relationship table (TRT) setting
CPU: 5 seconds
TSR0: 30 seconds
TSR1: 30 seconds
TSR2: 8 seconds
TSR3: 8 Seconds
BUG=b:65467566
TEST=build, boot on soraka, and verified by thermal team.
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Change-Id: I6af93fa358a037df2088213ee4df5e2cfd047590
Reviewed-on: https://review.coreboot.org/21453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fine tune usb 2.0 strength for port 4 to pass eye diagram.
BUG=b:65306272
TEST=build on soraka, measure usb2.0 eye diagram, and result is pass.
Change-Id: I2c79e96e2e3dea1364d7b71af19b57f4c9307fcb
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds imon and vmon slot numbers for Maxim 98927 driver.
These values are used to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I4382da4f984507d147751c168e8177b58c88a70f
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable PCIe Advanced Error Reporting for PCIe root port 0.
Change-Id: I76742801e84449d0910ddadf31d39597df3263b9
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/21402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently PMIC (tps68470) is in active state even when cameras are not
in use. PMIC is put into SLEEP mode only when entering S3 via
smihandler.
With this change PMIC will be put into SLEEP mode as soon as sensors &
VCM voltage outputs are turned off. This will allow run time power
saving when camera is not in use.
PMIC will be reset in first boot & across S3 & S0ix cycles.
Also, remove the smi handler for PMIC power management & handle it as
part of sensor and VCM ACPI PowerResource.
BUG=b:63903239
TEST= Build for Soraka. Check Camera probe, Capture image across
S3 & S0ix cycles.
Also checked the following & found no regression:
1. Typical camera use cases
2. Stability tests related to camera
3. Reliability tests related to camera
4. PnP tests related to camera
5. Latency related tests with camera
Change-Id: I23b0c0a887c9eb5d29b89f14aebba273b01228e0
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We have no wacom digitizer on I2C#3, so remove it.
TEST=build and boot on soraka.
Change-Id: I3f5a1b9ece6fc9a9443477c7a7aa77dbcdf6a703
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21309
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:64987428
TEST=Verified that touchscreen works on boot-up and after
suspend/resume. No power leakage via stop gpio in suspended state.
Change-Id: Ia260eb444081dbe1646c90e82c2725661e7306bc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
We no longer use this touchscreen device, so get rid of it.
BUG=b:64987428
Change-Id: I67af787d231317a80998fb483eed5674de19aeb4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Tune I2C params for I2C buses 0, 1, 2, 4 and 5 to ensure that the
frequency does not exceed 400KHz.
BUG=b:35948024
TEST=Verified for 25 iterations that the frequency on each bus ranges
<= 400KHz.
I2C0: 393 - 397
I2C1: 393 - 400
I2C2: 392 - 400
I2C4: 392 - 400
I2C5: 392 - 400
Change-Id: I3e12c75eb7e82a83aa6a6bcfcc11c12f83f2d3d4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch to provide new config options to perform LPC and SPI
lock down either by FSP or coreboot.
Remove EISS bit programming as well.
TEST=Build and boot Eve and Poppy.
Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update PL2 override setting to 15W as per KBL Power Arch Guide.
Change-Id: I4a6f875f8c3bdb012d6ff97c1429f32db5210893
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/20943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPP_B8 acts as input to the inverter whose output controls PERST#
signal to wifi module. Out of reset, GPP_B8 is configured as
input by default. Since there is no external pull-down on it, this
line is floating and results in PERST# being asserted until ramstage
where the GPIO was originally configured. Because of this the wifi
chip is not ready during the PCIe initialization step. Move the
configuration of GPP_B8 to bootblock so that wifi device is taken out
of reset as early as possible.
BUG=b:64181150,b:62726961
TEST=Verified with warm reboot and suspend-resume stress test that
wifi is still functional.
Change-Id: I68e1bd67499262a17daade72e9a9fd32934a184d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add gpio.c to bootblock so that the variant early_gpio_table can be
used for configuration in bootblock.
BUG=b:64181150,b:62726961
Change-Id: I77181334257f2fd19982ecafc1f58afe912f4280
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
WLAN_PE_RST control was moved from EC to SoC, it connected to GPP_B8.
Configure GPP_B8 to drive low.
TEST=Wifi card is detected and connect to an AP.
Change-Id: I6a6ea0ddefe8402284fe37665864c7a1961cbc15
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/20804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
After updating to Wacom Firmware version 501, touchscreen can't work.
Wacom FW (ver. 501) enables STOP function.
STOP Pin:
High: Normal Operation
Low: Stop Scanning
So pull TOUCHSCREEN_STOP_L high
BUG=b:37007801, b:37265219
BRANCH=none
TEST=manual testing on Soraka board and touchscreen works at boot
and after suspend/resume.
Change-Id: I8a2bdce1554fd99dea30cf91fa48d0529f40b7b0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/20664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable S0ix for poppy and soraka in their device trees respectively.
BUG=b:36630881
BRANCH=none
TEST=Verified S0ix and S3 operation on Poppy and Soraka (250+ iterations).
Change-Id: I9ba91499e54f729970448af6f71804ad5b3cb836
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPP_B7, GPP_D1 and GPP_D2 are not used going forward. Mark them as NC
in gpio table.
BUG=b:62322846,b:62240755
Change-Id: I7aee08314e6ce96d5913ae315bf75f5c04ab7370
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20672
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that soraka is starting to deviate from the baseboard w.r.t. gpio
settings, make a new copy of gpio table before we make any
variant-specific changes in it.
BUG=b:62240755,b:62322846
BRANCH=None
TEST=Verified with gpio_debug=1 in skylake/gpio.c that the gpio
configuration before and after this change remains same.
Change-Id: I448d18f18b63e9bfb739c518d599de3b9b602dc2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add wacom touchscreen support.
BUG=b:37007801, b:37265219
BRANCH=None
TEST=manual testing on Soraka board to ensue that touchscreen works
at boot and after suspend/resume.
Change-Id: I0fbae4782c6442149cda57d23c61ed87546621bb
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/20476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update Psi2Threshold, IccMax, AcLoadline, DcLoadline
VR config settings as per board design.
BUG=b:62063434
BRANCH=none
TEST=Build and boot soraka.
Change-Id: I254bbb88b82ddf278f0ec71bc98873df1d5e0d27
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: G Naveen <naveen.g@intel.com>
Reviewed-on: https://review.coreboot.org/20309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Soraka uses MPS2949 IMVP8 controller and does not need the VR
workaroud similar to Eve.
BUG=None
TEST=Build & boot on soraka. Ensure IMVP8 controller goes to low power
mode in S3 and S0ix by measuring power.
Change-Id: Ib98bb709ecc9e362a5cef437e7319e41f398a73b
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/20255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove MIPI camera related register entries from devicetree.cb.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy and soraka.
Change-Id: Ic6a6a98d4c8ed6cba760eae5fd87bc2a3f15d7d2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/19619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=Verified that board still boots to OS without any error.
Change-Id: I02d2a6cbcab92766a35993bfd20aaeed4ca22c90
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that we dynamically disable TPM interface based on config options,
add support for generation of SPI TPM ACPI node if SPI TPM is used.
Change-Id: I87d28a42b48ba916c70e45a061c5efd91a8a59bf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update user facing camera i2c address to 0x36.
BUG=None
TEST=Build & boot on soraka. Make sure user facing camera is detected.
Change-Id: I4645ae5734faef4b6a821c04ab817a7b99da6e4b
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
1. Do not enable touchscreen device by default in gpio configuration.
2. Select use of PowerResource for touchscreen device in devicetree so
that the ACPI subsystem can take care of powering on/off the
device. When system enters suspend, touchscreen device is powered off
and on resume, it is powered back on.
BUG=b:62028489
TEST=Verified 100 cycles of suspend-resume. Touchscreen still works on
poppy.
Change-Id: Ia0bebc7259b10cc60a9fa5b53542dfdd9685663e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19829
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Soraka uses OV 13858 sensor. Hence update the same.
Change-Id: I4dd39a25da47e379cca3f8748250b3ce1ff61e50
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:37712455
Change-Id: Ia3d13ac7c18be8fa92603b6501a2e5df476adcf0
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19766
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add a separate devicetree file for soraka variant and add H1 node.
2. Enable H1 TPM for soraka.
BUG=b:36265511
Change-Id: Id9947dce9b7f755971f0199f043af8d251d275ab
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19519
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
BUG=b:37712455
Change-Id: I3209aaef774712edab5e9f656ee84bfb6917b1c1
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19472
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Create Soraka board which derives from Poppy, a KBL reference board.
More Soraka specific changes need to be done later on.
BRANCH=master
BUG=b:36995255
TEST=Build (as initial setup)
Change-Id: I8af68d2cf475df56336aa0e3bebe86a54ece1999
Signed-off-by: YH Lin <yueherngl@chromium.org>
Reviewed-on: https://review.coreboot.org/19343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|